HP ENVY 750-170se: cannot access the RAID configuration via Ctrl + i on startup

Similar Questions

• Cannot access the AIP SSM via ASDM

  CISCO recommendations below:

  Cannot access the AIP SSM via ASDM

  Problem:

  This error message appears on the GUI.

  Error connecting to sensor. Error Loading Sensor error

  Solution:

  Make sure that the IPS SSM management interface is up/down and check his IP address configured, default gateway and the subnet mask. It is the interface to access the software from Cisco Adaptive Security Device Manager (ASDM) on the local computer. Try to ping the address of management of IPS SSM IP interface on the local computer that you want to access the ASDM. If it is impossible to do a ping check the ACLs on the sensor

  ----------------------------------------------------------------------------------------------------------------------------------------------

  I've tried everything recommended above. I can ping the host ASDM the FW and the SSM-10 module. Well, I ping the host machine and the SSM of the ASDM. I opened as wide as possible ACL. I changed the IP addresses and masks several times. The management of the ASA port and the SSM and the PC are on the same subnet.

  A trace of package from the PC to the SSM shows that it is blocked by an ACL rule, and yet I opened wide.   I've seen this kind of problem before and it was solved by applying the double static NAT, but I don't know how to do that if all the IP addresses are on the same subnet.

  Tried everything, need help from high level.

  The IDM software that comes with ASDM does not support java 1.7. The portion of the ASDM ASA supports 1.7 but launch the IPS cmdlet works only with 1.6. The TAC enginner suggested that I use the IME (IPS Manager Express) which is available for free on the Cisco's (http://www.cisco.com/en/US/products/ps9610/tsd_products_support_general_information.html) Web site.

  I've been playing with it today, and so far it seems to work pretty well.

• Cannot access the raid config in the BIOS on m8330f

  Recently given a m8330f to see if I could fix it.  much to my surprise, I find that it was originally built with two 320 GB drives in raid 0.  My thoughts on this side, I can't find how to access the raid controller in the bios to make changes.

  The RAID was already broken when I received it.  IM thinking its a nforce2 chipset and I used to have a Board with this chipset on it and it was pretty obvious where the raid utility.

  can someone help me?  can someone also as a side note, explane to me what thought HP sells a Computer Configuration with RAID 0 out of the box?

  Hello

  I can't tell what thought HP during the implementation of RAID for CTO models , using the card mother NARRA3 was released.  Review the image below.

  

• Cannot access the Media folder via App IOS Readycloud

  I have a RN204 4.6.2 running in an OSX system which will not allow access to the Media folder via the IOS app on iPhone or iPad. I can access the media folder via the ReadyCloud portal or the finder on MAC without problem, but the IOS App shows "Access Denied" and requests user & password, which, when entered, does not. I can access all other folders via the application, just not the media folder. Permissions are set the same as the other issues so I'm not sure what the question is that if she's Readycloud app for IOS. I guess the user & password requested is for NAS, although I tried the credientals of Readycloud just for fun but no help. As a note, I don't get "Connection failed" but "Access Denied", so the network access is OK but access to the file is doesn't understand why all other folders are accessible but not the media folder. And that's on both VPN connections & local. Any ideas?

  OK, get it fixed. I have changed the name of the folder, allowed full access, then he changed the name of moose. Now I can access the folder via the ios app. I'll have to rescan the actions in my media streamer, but to the East, I now access app.

• Cannot access the Web Configuration of RE1000 page once I have connected to my wireless network

  I can't access the Setup page of my wireless range Extenders RE1000 via IP 192.168.1.1 address once I have connected the Extender to my wireless network.  I was connected to the router via my mac and even took my mac out of wireless networks (just to be sure he wasn't trying to get to the IP 192.168.1.1 wireless.

  It happened a few times.  After it happened the first time I reset the access point and was able to get back to the web administration page.  I updated the firmware and exactly the same problem repeated once I plugged in my network home.

  This is a security feature? (Perhaps once it's on the wifi network you don't want just anybody access admin functions...?) A bug?  Or something else?

  Thank you

  If you don't set a static on the RE when IP address configure it on the connection of the SSID, it will grab an IP address from the router. You need to look in the router DHCP client table to find the RE of the new IP address. You can also use a reservation DHCP from the router to assign an IP address to the STIMULUS, but static IP is the best.

• Customer remote cannot access the server LAN via VPN

  Hi friends,

  I'm a new palyer in ASA.

  My business is small. We need to the LAN via VPN remote client access server.

  I have an ASA5510 with version 7.0. I have configured remote access VPN and it can establish the tunnel with success. But I can not access the server.

  Client VPN is 5.0.07.0290 version. Encrypted packages have increased but the decrypted packet is 0 in the VPN client statistics, after I connected successfully.

  Next to the ASA, I show crypto ipsec sa, just deciphering the packets increase.

  Who can help me?

  Thank you very much.

  The following configuration:

  ASA Version 7.0(7)
  
      !
  
      hostname VPNhost
  
      names
  
      dns-guard
  
      !
  
      interface Ethernet0/0
  
      nameif outside
  
      security-level 10
  
      ip address 221.122.96.51 255.255.255.240
  
      !
  
      interface Ethernet0/1
  
      nameif inside
  
      security-level 100
  
      ip address 192.168.42.199 255.255.255.0
  
      !
  
      interface Ethernet0/2
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      !
  
      interface Management0/0
  
      shutdown
  
      no nameif
  
      no security-level
  
      no ip address
  
      management-only
  
      !
  
      ftp mode passive
  
      dns domain-lookup inside
  
      access-list PAT_acl extended permit ip 192.168.42.0 255.255.255.0 any
  
      access-list allow_PING extended permit icmp any any inactive
  
      access-list Internet extended permit ip host 221.122.96.51 any inactive
  
      access-list VPN extended permit ip 192.168.42.0 255.255.255.0 192.168.43.0 255.255.255.0
  
      access-list VPN extended permit ip 192.168.43.0 255.255.255.0 192.168.42.0 255.255.255.0
  
      access-list CAPTURE extended permit ip host 192.168.43.10 host 192.168.42.251
  
      access-list CAPTURE extended permit ip host 192.168.42.251 host 192.168.43.10
  
      pager lines 24
  
      mtu outside 1500
  
      mtu inside 1500
  
      ip local pool testpool 192.168.43.10-192.168.43.20
  arp timeout 14400
  
      global (outside) 1 interface
  
      nat (inside) 0 access-list VPN
  
      nat (inside) 1 access-list PAT_acl
  
      route outside 0.0.0.0 0.0.0.0 221.122.96.49 10
  
  
      username testuser password 123
  
      aaa authentication ssh console LOCAL
  
      aaa local authentication attempts max-fail 3
  no sysopt connection permit-ipsec
  
      crypto ipsec transform-set FirstSet esp-des esp-md5-hmac
  
      crypto dynamic-map dyn1 1 set transform-set FirstSet
  
      crypto dynamic-map dyn1 1 set reverse-route
  
      crypto map mymap 1 ipsec-isakmp dynamic dyn1
  
      crypto map mymap interface outside
  
      isakmp enable outside
  
      isakmp policy 1 authentication pre-share
  
      isakmp policy 1 encryption des
  
      isakmp policy 1 hash md5
  
      isakmp policy 1 group 2
  
      isakmp policy 1 lifetime 86400
  
      isakmp nat-traversal  3600
  
      tunnel-group testgroup type ipsec-ra
  
      tunnel-group testgroup general-attributes
  
      address-pool testpool
  
      tunnel-group testgroup ipsec-attributes
  
      pre-shared-key *
  
      telnet timeout 5
  ssh timeout 10
  
      console timeout 0
  : end
  

  Topology as follows:

  

  Hello

  Configure the split for the VPN tunneling.

  1. Create the access list that defines the network behind the ASA.

     ciscoasa(config)#access-list Split_Tunnel_List remark The corporate network behind the ASA. ciscoasa(config)#access-list Split_Tunnel_List standard permit 10.0.1.0 255.255.255.0 

  2. Mode of configuration of group policy for the policy you want to change.

     ciscoasa(config)#group-policy hillvalleyvpn attributes ciscoasa(config-group-policy)#

  3. Specify the policy to split tunnel. In this case, the policy is tunnelspecified.

     ciscoasa(config-group-policy)#split-tunnel-policy tunnelspecified 

  4. Specify the access tunnel split list. In this case, the list is Split_Tunnel_List.

     ciscoasa(config-group-policy)#split-tunnel-network-list value Split_Tunnel_List 

  5. Type this command:

     ciscoasa(config)#tunnel-group hillvalleyvpn general-attributes 

  6. Associate the group with the tunnel group policy

     ciscoasa(config-tunnel-ipsec)# default-group-policy hillvalleyvpn 

  7. Leave the two configuration modes.

     ciscoasa(config-group-policy)#exit ciscoasa(config)#exit ciscoasa#

  8. Save configuration to non-volatile RAM (NVRAM) and press enter when you are prompted to specify the name of the source file.

  Kind regards
  Abhishek Purohit
  CCIE-S-35269

• Cannot access the server gmail via any web browser; code 105 error message cannot access server

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: have cleared cache, spilled all saved passwords and I can not even access accounts gmail via Google Chrome; Internet Explorer or Firefox... I can not access through my laptop but can access files in gmail on other public computers

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  http://www.Google.com/support/forum/p/chrome/thread?TID=1b6ea4f035dadc16&hl=en

• Cannot access the web configuration utility - server wrote: level_15_access

  I've been using a Dlink router and wasn't getting any beach on my network, so I tried to configure my router linksys wrt150-n v1.1. I pressed the button reset for 20 seconds, then unplugged my modem (cable) and the router, then plugged in. When I open a browser window and type http://198.162.1.1, instead of open the configuration page, I get a message saying "the http://198.162.1.1:80 server requires a user name and password. "The server said: level_15_access.

  I left the empty user name and used the password default admin, and who does nothing.

  Tried to reset the router on 4 or 5 times without success. Any ideas on what I forget? I did not initially provided with the router Router installation CD, and it is not a downloadable file - I should be able to and have in the past been able to use the default IP address and the admin PW.

  Thank you!

  Try a Hard Reset:

  Hard Reset (aka 30/30/30 reset):

  The following procedure will clear the memory NVRAM and set dd - wrt return to default values:

  • With the power on, press and hold the reset button the back of the unit for 30 seconds
  • Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
  • Plug in the appliance ALWAYS keeping the reset button a final 30 seconds

• cannot access the internet after upgrading to firefox 30.0 on windows 7

  After the upgrade to firefox 30.0 on windows 7, cannot access the internet. FF 30.0 works OK under Vista

  Sometimes it's because of your security software thinking that the upgrade may not be legitimate. You can consult this article: problems connecting to websites after Firefox update.

• Just upgraded to El Capitan and cannot access the calendar. It opens with a "Shift schedules to the server" message Can only Force Quit

  Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.

  I cannot access all features and can be closed only by using force quit.

  Please stop calendar and also the application of reminders, runs. Force quit if necessary.

  Back up all data.

  If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.

  If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.

  Launch schedule and see if there is an improvement.

• I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
  Turn on/off the menu bar is a new feature in version 3.6.
  (Linux and OSX see: what happened to the file, edit and view menus? )
  Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
  Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
  The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
  See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing

  Navigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).

  To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).

  Mode full screen
  http://KB.mozillazine.org/netbooks#Full_screen

  See also:
  Back and front toolbar buttons or others are missing
  Customize controls, buttons, and Firefox toolbars

• 42RL833 - latest Firmware installed and cannot access the YouTube app

  I have 42RL833 Toshiba which is updated to the latest firmware, however I still cannot access the application on my YouTube. I get an error saying that Youtube XL is no longer supported.

  What can I do to fix this?

  > I get an error saying that Youtube XL is no longer supported.

  Google has stopped the YouTube XL service and, therefore, this service isn't available anymore.
  http://www.Toshiba.EU/innovation/generic/YouTube-XL/

  You can read details here:
  https://support.Google.com/YouTube/answer/3123170?hl=en

  It also seems that YouTube XL has been replaced by YouTube Leanback Lite:
  http://www.YouTube.com/leanbacklite
  See also:
  https://support.Google.com/YouTube/answer/3153576#

  There is also a note that if you can connect your computer to your TV, you can continue to use the YouTube TV-optimized experience by visiting youtube.com/tv.

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!

• "Windows cannot access the specified device, path or file" for each X 86 application on a Windows 2003 x 64 server

  Hello

  I have a Windows 2003 X 64 server and since a week ago everything works fine.

  For a week or two when I try to run an X 86 application, I always get this error:
  "Windows cannot access the specified device, path or file.
  If I run a x 64 apps everything works fine.
  What made a mistake?
  Thank you

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please post your question in the TechNet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• I get all the time can not download anything 'Windows cannot access the specified device, path or file. You can't have the permissions to access the have__appropriate element. »

  Original title: problems cannot do anything

  Windows cannot access the specified device, path or file. You can't have__appropriate the permissions to access the item. I get it all the time can not download anything

  Hi birdylod,

  ·         What version of the operating system is installed on the computer?

  ·         You did changes to the computer before the show?

  ·         You use Internet Explorer? If so, what version are you using?

  ·         What files you download?

  Follow these methods.

  Method 1: Performs a search using the Microsoft safety scanner.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 3: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  For reference:

  What to know before applying permissions to a file or folder