HP Envy Rove 8.1 - when the monitor sleeps, it cannot be restored

Similar Questions

• How change the default resolution for windows to use when the monitor is not connected

  Hi, how can I set the resolution by default that windows uses when the monitor is turned off or not connected at all? My problem is that normally I use 1920 x 1080, but when I put the pc to sleep or just turn monitor and leave it like that for a while with a few app maximized, when I get back and turn the monitor on the resolution is correct but the enlarged window is resized to 1024 x 786 resolution. I tried to change in the registry DefaultSettings.XResolution a DefaultSettings.YResolution in all instances and it worked fine for a long time. Then some update that happened and now it no longer works. I reinstalled the system, but it still does not. How can I force windows to use always the 1920 x 1080?

  It seems that TMM disabling did the trick. Maximized windows are not yet moved to the left edge of the screen, well, those who have been maximized is maximized correctly as they should. I had to disable TMM through registry as I had no MMR in Task Scheduler.

  If anoyone is interested I've followed the instructions described here:

  http://superuser.com/questions/120983/how-to-disable-monitor-auto-detection-in-Windows-7

• windows program will rearange themselves when the monitors are in mode 'sleep' - how to stop windows switching screens

  IV has 3 screens on a map via display port adapter and a 4th on a second card in order to have a 1 on top of three parameters.

  the computer itself does not sleep because I have servers running but I put screens on standby after 10 minutes.

  for a long time, all screens would go to sleep and wake up without any problems... in the course of the last months, 2 questions.

  1. once the monitors to sleep and no consistent time 1 monitor wakes up enough to show the backlight, but no display... wake up ok and sometimes screens dislocated.

  and

  2 when the monitors have the power save / standby mode, some of the Windows I had open will have been moved to different monitor as monitors have been disconnected or "detected" numbers have changed and I saw the change number several times as well, but not always.

  I say some because I have 4 windows open on my left most monitor and 2 of them end up on my right monitor after the glitch.

  Sometimes things on my low Center {main} will end up on the top of the single monitor page.

  no rhyme or reason... a few days no problem at all don't wake up and everything is where it should be and all the screens have slept through the night

  for all the tech info

  ATI 5750 and 5770 in mode xfire w / 1displayport/DVI / HDMI/DVI 1 / 1 DVI.

  and ATI 5450 to the top of the monitor page

  Windows 7 x 64 / 8 core AMD8320 / 16 gig mem.

  latest video drivers...

  any info?

  I'm a tech and iv been scratching my head for a while on this one

  thnx in advance for reading even to see my problem

  thnx even more for an answer... lol

  Hello

  Welcome to the Microsoft Community Forum.

  The question you posted would be better suited to the TechNet community.

  Please visit the link below to find a community that will support what ask you:

  Microsoft TechNet

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  Thank you

• HP Envy m7-n011dx: HP Envy m7-n011dx - change to external monitor Sleep Mode close lid so that the aid & external keyboard

  I added an external keyboard and an external monitor to my HP Envy laptop m7-n011dx.  Both are recognized by the laptop, if I leave the lid open.  When I close the lid, the computer goes into mode 'sleep', and I can't use the laptop with the keyboard and the monitor.

  How do I charge the laptop does not go in mode 'sleep' when I close the lid, so I can use the keyboard and the monitor?

  Thank you very much!

  MPBEqual

  Hi @MPBEqual,

  Welcome to the HP Forums!

  I read your post and wanted to help.

  I understand that you want to use the external keyboard and the monitor while the laptop lid is closed.

  You must go to the Power Options. Set it to do nothing when the lid is closed.

  You can view this document in order to manage power options:

  HP Notebook PC - management Power Options (Windows 10)

  Thank you for being a part of the community of HP. Please let me know if that helps solve the problem by marking this message as "accept as a Solution. If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me congratulations.

  Kind regards

• How can I change the video display Mode when the monitor mode not supported?

  While creating my new monitor, I changed the computer video display mode at 120 Hz by accident.  Now I see something on the monitor other than the words not taken in CHARGE the MODE.

  My system is a new HP Pavilion p7-1423W running Windows 8.1 with Intel i5-2320 3 ghz

  I tried the start mode by pressing ESC on power but do not help the startup options.  And the just F11 menu option makes the startup screen disapear and puts the monitor mode not supported.  Tapping F8 doen't work and tapping F12 just puts me in the bios menus that do not help.

  How can I upgrade the video card integrated with a video mode that is supported when I can't see the screen?

  I answer my own question because I found my solution, thanks to my grandson (freshman to Renselear Politech).

  I shoot to buy a monitor that displays a refresh rate of 120, so I could put my rear view.

  Here is the solution.

  My computer double exit DVI.  My grandson told me to connect my new monitor to the other output because the output does not get touched when I changed the original mode of production.  He has worked and is automatically selects the default monitors mode.  Then I've reconfigured the original output using the integrated display software. Solved!

• No Signal message when the monitor is connected to the graphics card.

  Thus, after posting this problem on different forums, I was told that my power (300w) was too low for my Radeon HD 7570 I tried to install. After you install a 585w power supply, the problem is still happening.

  Model: HP Pavilion h8 - 1240 t

  OS: Windows 7 64-bit

  Error: Monitor says "no signal" when connected in the PCI slot where is the graphics card.

  Changes: this always happened, did not get a single card to run this stupid computer!

   

  The DVI cable is completely plugged the monitor into the PCI slot and the graphics card is fully in. The fans on the graphics cards spin but it is not detected at all. It does not appear in Device Manager.

  Data sheet:

  I7-2600 3.4GHz

  8 GB RAM

  Orion 585w PSU

  Radeon HD 7570 (it didn't come with the computer, otherwise it would work...)

  PEGATRON CORPORATION 2AD5 1.03 (I guess that's the motherboard)

  No. I went to Dell and downloaded THE drivers that ACTUALLY work. Computer restarted and everything works fine.

• Resolution is lower when the monitor is connected to the laptop

  Recently, I knew that my laptop of girlfriends who is a Dell XPS streched to the office and the max resolution is 1280 x 1024, what happened during the night. The resolution used to go up to 1680 x 1050.

  The stretching occurs only when its acer monitor is connected to the laptop. When disconnect us the laptop resolution is up to 1900 x 1200 (finally something like that).

  Operating system is windows 7 x 64.  I have the exact same monitor works fine on a windows Vista on a Dell XPS.

  Anyone know what to do about it?

  
  

  Best regards Sune

  Well, I have the same problem with my lcd... and I discovered that this is due to the ability of the tv... or the screen, your laptop have a high native resolution but perhaps the native resolution of your screen is less than I say 1360 x 768... by that your pc or laptop detects the monitor and adapt to... but this will give you a No 4 k true HD display.

• System hangs when the computer sleeps with error KMode_Exception_Not_Handled after generation installed 9926

  Since the new version update (9926), whenever my computer goes to sleep or when it is left for several hours compress I get unhandled KMode Exception error.  I deleted a suspicious program who has problems during the previous generation, but that made no difference.  When the computer restarts, I wonder if I want to use the previous windows platform and I encounter the KMode problem, but after a day or two, the computer did an update to 9926 and I started having the problem again.  I looked for all devices that are evidence of a driver problem and have not found any.  Tech is able to examine the file DMP to give me a clue as to the program/device must the fixed driver so that I can get past this error?  Here is a link to the folder that contains the file.

  https://onedrive.live.com/embed?CID=932A5B907D806E8A&RESID=932A5B907D806E8A%21225306&AuthKey=AMaX68Y4-fpbXcE

  I looked in the pilot and I have the most up to date, but I was able to solve the problem until the next update by turning on my screensaver and do not allow the HARD drive to sleep.

• Disable the lock screen sleeps but not when the computer sleeps.

  Hello
  My goal (and thousands of other users of Windows 8) are to save the batteries without be pestered constantly to enter my password - but at the same time to preserve the security of the computer.
  My goal is the following:
  -Screen could sleep in X minutes (to save power) without the computer
  -Lock the computer when the computer goes to sleep in X + Y minutes.
  I intentionally left the details that are not important. Please do not post a response unless you have been able to do successfully is Windows 8 - i.e. only requires a password when the computer goes to sleep, but not the screen.  It was no problem in Windows 7.  Is - this another Windows 8 'development '?
  X and Y are two positive integers. 8-)
  I expect an answer of reg-edit...
  Thank you

  Hello

  1 have had any changes made on the computer before the show?

  2. have you set any screensaver on your computer?

  If you have set a screen saver, I suggest you to follow these steps and check if it works:

  a. right click on the desktop.

  b. click on Customize.

  c. click on screen saver.

  d. in the new window, uncheck the option on the resume, the logon screen.

  e. click apply and OK.

  Let us know the results.

• Alterations of the screen when the monitor or projector is connected to the Tecra M5

  Hello

  I do experience screen corruption when (and only when) I use my Tecra M5 connected to an external monitor or a LCD projector, through a VGA cable and via a cable DVI (and docking station). It seems fine when I use the internal LCD screen.

  He got a Nvidia Quadro NVS 110 M video card with, apparently, the most recent drivers. Alterations can be captured with a copy of Θcran, but I can't post the JPG here! They are usually green or magenta and look like rectangles, longer than high, about 2cm long and full of dashed horizontal lines.

  Sorry for the vague description - but he doesn't that sound familiar to anyone?
  Thank you

  Hello

  I can't say exactly what it could be, but I n t think that there is something wrong with the graphics card.
  I think that if the graphics card would be corrupted, therefore the fault or whatever is displayed on the internal display, but it doesn t.

  Have you changed the screen resolution? Or have you changed the color quality?

• How to fix a pc when the monitor receives no signal?

  I have a hp m9000t series, recently, I do some changes in the BIOS and after the record setting and the release of the bios computer restarts, but monitor losing signal. After many restarts still no luck still blank monitor. How can I fix my pc without monitor get a signal? BTW... I'm sure that all devices are working correctly. It is in any case to restore the setting without the bios screen?

  Hello

  Shut down the PC, remove the AC power supply.  Follow the procedure to clear the CMOS, which is under the heading "Compensation bios settings" to the bottom of the page on the link below.  You must make sure that you put yourself in the Earth or wear an anti-static strap to prevent damage to components on the motherboard.

  http://support.HP.com/us-en/document/c01077641

  I hope this helps.

  Best wishes

  DP - K

• How to make a copy of the sent IMAP messages when the sent folder file cannot be found?

  My Thunderbird works fine. I also see messages in the "sent" folder but I wonder are only registered in the IMAP server messages. For the backup application, I would like to copy the file from the "sent" folder but I can't find a local file for this.

  In home/me/.thunderbird/44g5fxvp.default/ImapMail/mail. .fi [mymail] I have files
  Archives - 1.sbd
  Archives.MSF
  Deleted messages
  Messages.MSF deleted
  Drafts.MSF
  INBOX
  INBOX.msf
  inbox_old
  inbox_old. MSF
  msgFilterRules.dat
  Sent.MSF
  Templates.MSF
  Trash.MSF
  Trash.SBD

  IE Sent.msf exists but is not named file sent. I am looking for a bad place? My Thunderbird settings or preferences are wrong? Is there something obvious that I missed?

  What is the most convenient way to make a local copy of the sent messages folder if Thunderbird does not have a local copy of it?

  Information on my system:
  The application databases
  Name Thunderbird
  Version 31.0
  User Agent Mozilla/5.0 (X 11; Linux x86_64; RV:31.0) Gecko/20100101 Thunderbird/31.0

  Application version identifier 20140721092545
  Permit Plugins about: plugins
  Build configuration about: buildconfig
  Memory usage on: memory

  Mail and News accounts
  [...]
  account3 mail (imap). [mymail] .fi:993 password smtpa Normal SSL/TLS. true password [mymail] .fi:465 Normal SSL/TLS

  Subscribed IMAP folders accounts configured to synchronize and place a copy of the folder on the server in the profile of mail, but this issue is constantly updated to match the server, so if you have new messages then these changes are made to the server folder and the folder on your computer is updated to match the server folder. Or if you delete mail from your copy then it will update the server. Then synchronized files are constantly changed and updated.
  Moving while copy/move, it stops the activity on files synchronized and enables offline that get you a copy to anywhere else you want.
  Less chance of something going wrong.
  then go back to online mode.

  I knew that some people have problems with copy/move emails in online mode that are offline.

  Easy way to go 'offline and online.
  To go offline:
  Click 2 bluescreen icon located in the bottom left of the status bar.

  To go online again:
  Click 2 screen black icon located in the bottom left of the status bar.

  Some useful info on IMAP backup:

  • http://KB.mozillazine.org/IMAP_backup

  ImportExporttool - very useful:

  • https://addons.Mozilla.org/en-us/Thunderbird/addon/ImportExportTools/

• reloading windows vista when the windows version 7 cannot be permitted?

  I bought windows 7 for my laptop earlier this year and have no problem. However STUPPIDLY that I have loaded on the rise also on my desktop do not know that it could be run only on a single computer. I just want to re install windows vista on my desktop since it is the version with which it came. However I can't find the restore for vista disc or product key. I need them as surely as they were not completely removed from the computer during the installation of 7. What is the best way?

  Desktop manufacturing may have provided a "recovery Partition" on the drive hard, check the owner's manual or call the technical support of the manufacure team. You can also request filtering alternatives if you have no restore partition.

  As for a product key, check the side or back of the case for the product key sticker.

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• SimplePass scanner stops working when the laptop sleeps

  Hi, I have a Pavilion m61045dx notebook for Windows 7 64-bit.  I managed to get any installation Simplepass chose Google Chrome as a browser, because it seems that Firefox does not support this version of Simplepass 5.4, and then the fingerprint reader has stopped working.  I found a suggestion on this forum or another, can't remember now that said to go to the Device Manager and choose the validity and under power management sensor, uncheck the box "allow the computer to turn off this device to save power".  Rebooted as directed and Voila! validity sensor works again. But now every time that the computer will sleep the validity sensor does not power back upward with the rest of the computer.  Whenever this happens, I was able to make it back by going to Device Manager and the deactivation and reactivation of the validity sensor and then restart.  But seriously, what a pain.  Any suggestions?  I'd be happy to find that it is just a matter of setting, but failing that maybe an update to the latest version for my machine.  Unfortunately, the software Simplepass has no option ' check for updates ', or device driver updates either.  Any suggestions?

  Please disable power saving mode for USB in Device Manager.

  · Click on Start Orb > typeDevice Manager in the search box

  · Click Device Manager in the search results

  · Expand USB root huhb > right click on your mouse > clickProperties

  · Click the power management tab

  · Uncheck allow the computer to turn off this device to save power

  · Click OK

  that you change the power supply for the USB options.

  Here are the steps to do so.

  http://www.SevenForums.com/tutorials/147369-USB-selective-suspend-turn-off.html

  disable the mode of suspension from there...

  Hope this helps, good luck!

• Log on screen is displayed when the computer sleeps or battery operated

  I have a HP Elitebook 8470P running Windows 7 Pro. She put does not demand connection password. That works fine as long as I turned off the laptop and it starts the next time I use it. However, if I put the computer to sleep or unplug it, then run it on battery I get the login screens. It shows my administrative username and said that the account is locked. I click on that and a new page indicates my administrative username and says I'm connected. I then have to click on it to get to my office. Anyone know how to get rid of this problem? Thank you!

  Changing the way that the computer wakes from sleep?