HP Envy m7-n011dx: HP Envy m7-n011dx - change to external monitor Sleep Mode close lid so that the aid & external keyboard

Similar Questions

• HP envy 700-414: HP Envy 700-414 Windows 7 driver network controller says I don't meet the minimum requirements

  I recently installed Windows 7 on my hp envy 700-414 and missing a lot of pilots. A user by the name of banhiem gave me a link to download the drivers of a 700-230 hp envy. After I did it, I clicked on another link, it gave me to install the Realtek network controller. Whenever I tried to install the driver, it would tell me that I did not meet the requirements. Other drivers work fine now, except the network controller. The steps on how to fix this error would be greatly appreciated.

  Hello:

  See if this card wireless driver works...

  The package contains the Broadcom wireless LAN drivers and utility which are required to enable the LAN adapter wireless Broadcom integrated in the supported models that run an operating system supported.

  FTP://ftp.HP.com/pub/SoftPaq/sp70501-71000/sp70888.exe

• ENVY 15: Turn off Adaptive display for ca mode

  Hello

  I'm in the curiosity of how I can turn off Adaptive brightness for the external mode display.

  http://i.imgur.com/nnDnd9Y.jpg

  I already turned off in Power Options in Control Panel. Initially, it wasn't only to turn off Adaptive brightness so I also disabled display Power Saving Technology for battery operation of the Intel Graphics Control Panel.

  It works like a charm for Adaptive functioning on battery power but display is always active when the external power and I couldn't find an option to turn off in Intel Graphics Control Panel, there is no display of techniques for saving power for external power.

  http://i.imgur.com/WtLe6kB.jpg

  So, how can I stop the Adaptive brightness for current alternative before going blind in the sudden brightness changes when I am plugged into the wall?

  Any help is appreciated.

  Thank you!

  Hi @yldzanl ,

  Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP ENVY 15 laptop and wanted to turn down the brightness in AC mode. On your first page it shows you in editing parameters. You will notice that the brightness level, one for battery mode and the other for the AC adapter / CC, they are not the same.

  Change this to be the same for the battery and save the settings.

  Thank you should take care of it.

  Thank you.

• HP Envy 700-470na: changing the case of the HP Envy 700-470na.

  Today, I upgraded my PSU and GPU for my HP Envy 700-470na. The case for my PC is too small and I can barely sort out the cables.
  
  If someone can recommend a decent case that is less than £50, can put all the pieces of pc HP in the case like the motherboard, hard drive etc and lots of space for the circulation of air and cables. Who would be appreciated! Thank you. I hope that my problem can be resolved soon.
  
  PSU - Corsair CX600M
  GPU - EVGA GTX 970

  The form factor for the motherboard is: Μatx: 24.4 cm (9.6 inches) x 24.4 cm (9.6 inches).  You must buy a case that is made for this.  This means that the accessory in the case must match the holes in the motherboard.  HP has their mothers caught their specifactions cards.  So, they can be standard.  In addition, the connectors in the case may not match the connectors on the motherboard.  The front connector for the power button is the one who comes to mind.  It is very difficult to recommend a case that is certain to work.  You can find the case you like and contact the manufacturer for Technical Support to see if they can make sure it will work for your components.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• ENVY 15 t-k200: how to find if my 15 t-K200 motherboard supports a backlit keyboard

  I HAVE an ENVY 15 t-k200 AND would like TO KNOW HOW TO find OUT IF MY MOTHERBOARD SUPPORT a BACKLIT KEYBOARD

  Hello

  This isn't a CTO machine so no complete listing available BUT based on the following site, many machines on the same series (15-knnnaa) have backlit keyboard:

  http://support.HP.com/us-en/product/HP-envy-15-K200-notebook-PC-series/7527530/product-info

  I believe that all the machines of the series whlole have mother who sleeps for a backlite keyboard. Why you have not ordered backlit keyboard in the first place?

  Kind regards.

• HP Envy Rove 8.1 - when the monitor sleeps, it cannot be restored

  I recently started having a new problem where the monitor on my all in a touchscreen Envy Wick not wake up after sleeping. To the best of my knowledge, the computer turns on and seems to work, but the screen is still asleep. By pressing the power button, move the mouse or press the keyboard keys seem to wake up the monitor. When I hard shut down the computer by pressing the power button and then restart the system, everything starts fine. It has been improved for Win8 to 8.1, but I don't think it's when the issue began.

  I've been reviewing several similar problems, but none seem to reflect this specific question. Any guidance would be appreciated.

  SOLUTION:

   

  Open BIOS (at first press ESC, press f10).

  F9 for default of restor

   

  Then save and exit (press f10, once again)

  Restart the computer.

  Doing this again and set it back on "Enable" that can help the computer wil not fire.

  And now your ROVE will start and sleep properly.

• HP ENVY 7640: new HP Envy 7640 will not feed documents in scan mode

  New HP ENVY 7640 will not feed for scanning documents.  It transmit documents in copy mode but not when you try to scan several pages.

  Hello

  Thank you for using the HP Forums.

  Have you installed the software features FULL?

  If this isn't the case, please download and install the FULL features software:

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-7640-e-all-in-one-printer-series/6617267/model/6617268#Z7_3054ICK0K8UDA0AQC11TA930C7

  Once you have done this, launch the Scan software (via the HP printer Assistant) and make sure that the source is "heavy use document feeder.  (Example shown)

  

  For more tips scan, please reder to this resource:

  Scanning for Dummies

  Your printer uses the NEW interface of scanning.

  Hope that helps!

• disable the pop up keyboard hp envy m7

  I would like to disable the keyboard to form screen popping up whenever I click on the text box or in a document. I have a HP Envy with Windows 8.1 m7.

  Hello

  You can disable the service charge as follows.

  From the desktop, hold down the Windows key and press R.  In the run window, type services.msc and press to enter.  Navigate to the touchscreen keyboard and Handwriting service panel, right click and select Properties.

  In the drop-down list box next to "Startup Type", select disabled and click on apply to save the changes.

  Click on the "Stop" button to end the service.

  If you have never wanr to use on-screen keyboard, this service must be re-enabled and started the first.

  Kind regards

  DP - K

• Computer TouchSmart HP Envy 17 t 2 weeks without a break stop at or just after the connection

  Hello

  I really need help because I am pulling all my hair out with frustration. Here are the details:

  I got a new Notebook HP TouchSmart 17 t for my birthday last week. I'm a developer and a code about 15 hours a day, and my laptop 15 inch 3 years was certainly an obstacle. Needless to say, I was very excited by envy, especially 17-inch screen.

  That excitement lasted about 2 days.

  In the first two days of use, I installed all the Windows, Windows updates 8.1, Chrome, Visual Studio, SQL Server 2012 and Management Studio, MySQL Workbench, Adobe Creative Cloud, MS Office, and Avast. The system will periodically re-start during this time, but he wasn't even epidemic.

  But from about the 3rd day, the computer began to stop more frequently. Initially, it was once every 30 minutes or so, but then increased rapidly so it restarted at or just after the login screen 9 of the 10 startups. Every 10th reboot or so, the computer will allow me to connect and I immediately try troubleshoot it before it will re-start again in 5 minutes or less.

  The only thing I could think of that changed on the 3rd day is I installed Kaspersky to replace Avast (the laptop came with a 1 year free Kaspersky subscription). I didn't know if it was the culprit, or if I had a lemon of a computer that was overheating because of hardware problems, but to be sure, I tried to uninstall it. However, the computer wouldn't stay long enough for me to do.  I couldn't even in HP Recovery to restore the system.

  Fortunately, I had burned the recovery DVDs and was able to start the recovery tool by booting from the DVD. I restored the computer configuration with minimal additional software installed (restore failed the on the first trial to 99% complete, but the second test was a success). I was really hoping this would solve the problem so I can start using my new laptop.

  No luck.

  The first time I turned on the computer after the restore, it immediately starts close to, or just after the screen connection again. As before, I am able to use the computer for 5 minutes every 10th reboot or so before it restarts. During those rare moments, I was able to enter the power management settings to turn off sleep and Hibernate, given that several forum posts which indicate as a potential culprit. However, the computer won't stay long enough to install updates of window or Windows 8.1, or to ensure that all drivers are up-to-date.

  Furthermore, I believe that the BIOS flashed when Windows 8.1 has been installed and I wonder if it needs to be reset. (I don't think the restoration process reactivates the BIOS to its original settings, but I have really no idea.)

  Anyway, here I am with a new laptop that I can not use.  I don't know if it's a driver problem, software conflict, hardware problem, problem of BIOS or something else. Needless to say, I am very frustrated and I would really appreciate suggestions.

  Thank you

  Tom

  Tom, welcome to the forum.

  This isn't how HP computers to run.  I strongly suggest that return you it and get another HP computer that works.  If it does not work long enough to install the updates, it will very probably not get much better.  I want to help you to save your hair!

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP ENVY 120 CZ022B: Change the operating language

  Hello

  My HP Envy interface language has changed. How can I change it back to English?

  Hello @Penny4them ,

  Welcome to the forums of HP.

  I understand that the language on your DESIRE of 120 changed.

  I would like to help.

  Touch the key icon in the upper right of the display of printers.

  You should have 4 options.

  In English, they are Menu Setup, Web Services, Toolsand Preferences.

  Tap Preferences.

  The first option should be Set Language.

  You should see English as an option.

  If the dose that does not work for you, please let me know.

• HP Envy 17: portable lockout... can't login to my account using the login screen

  This is a brand new HP Envy, I had nothing but software problems, first windows 10 which he is responsible with and now this.

  This morning, HP has uploaded a new bios update. After a reboot in the name of account in the form it does not accept my password. There is no place for a PIN or fingerprint sigon either, only the password.  I know that it is the correct password because I wrote it down.

  I'm stuck on the computer. With the help of a computer laptop back to write this.

  Please HELP, I use this for a home business.

  Since it is a Windows password, I'll give you the same suggestion that Microsoft and HP are likely to give you.

  Remove the hard drive and put it in a drive enclosure hard usb.

  Connect it to another PC of Windows and copy all the important files on an external storage device.

  Once this is done, you can use the recovery media that you must have created by now to find your laptop to the factory delivered State in which it was when you removed from the box.

  Once you have done this, you should make sure that the HP download options are on install only when you want. Alternatively, you can stop Windows 10 update if you wish.  This should prevent your being in this situation once again.

  HP didn't download anything on your PC. You allowed the download occurs allowing the setting to be "automatically download and install updates". In other words, as you now know, not always such a great idea.

• E HP Envy 7640 All-in-One-Sanchez: now, I have my documents stuck in the queue and I can get out. Help! I hate this printer...

  Whenever I change the paper (photo paper) when I get back to paper ordinary, it is immediately past offline or it gets stuck in the queue.  Now it is stuck in the queue.  Is it possible to get this printer to print without all these problems.  I am extremely illiterate on computers and this crazy.

  You helped me with "off connection" now can help you with this problem.  Thanks for the help, I really appreciate it.

  Hello @Sam141, greetings!

  Welcome to the HP support forums. I'd love to help you with your printing problems with your printer Envy 7640.

  I understand that you are a new user with this printer, that's why I suggest using an automated tool to correct this and many other common printer related issues.

  Go to http://hp.care/2bZ9w2q to download and install HP print and scan the doctor. This tool will be quickly and automatically perform several tasks resolution known problems for this problem. You can save this for future issues you can still.

  Please let me know if that solves the problem, or if you need assistance.

  See you soon

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• HP Envy 15: Screen changes brightness level at random

  HP Envy 15

  Product number: K2N89PA #ACJ
  OS: Windows 8.1

  Intel graphics card

  The brightness level of the screen continues to change at random. I checked the different power management settings, but it does not help.

  Hello:

  There is a feature called Adaptive brightness W8.1.

  If you don't like screen brightness fluctuations, you can disable this setting.

  Check this link to see where to change this setting.

  http://www.intowindows.com/how-to-disable-auto-brightness-in-Windows-8-1/

• HP envy 23-c110xt all-in-one: MONITORS AND ACCESSORIES of the MULTIPLE

  Hello.. THIS? IS ON AFTER I PLUG MY MONITOR 2 TO MY HP VIA VGA USB ADAPTER DO I NEED A 2ND ANOTHER KEYBOARD AND MOUSE FOR THE 2ND MONITOR.  MY INTENTION WITH THE HELP OF THE 2ND MONITOR TO OPEN OTHER WINDOWS FROM MY MAIN PC... BUT IF I OPEN A DJ APP ON MY 2ND MONITOR OF THE HP ENVY ON THE RISE... HE WILL PLAY AGAIN THE AUDIO?

  You must not second mouse you just need to change your display mode to extend (a quick google will be answered on your operating system) and regarding audio, it will display the sound to a headset or speakers, but if you have connected, it will display the sound to the main display (the one with the bar downstairs with things like your apps) (a quick google this will help you to discover that one is)

  hope this helps

• HP Envy 750-197c Desktop: you can add a SSD internal flash disk to the envy of HP 750-197c Desktop

  You can add an internal SSD to the envy of HP 750 - 197c Desktop that has a 2 TB drive installed?

  DMSIceman, welcome to the forum.

  Yes, you can move the HARD disk and install an SSD.  You will need to buy at least a 128 GB SSD.  Here is the data sheet for the computer.

  The best way to install an SSD is to leave the current HARD drive as it came from the factory.  Connect the SSD drive to another SATA port on the motherboard.  Install the software of Migration data provided by the SSD manufacturer on the HARD drive.  Once installed, open it and follow the instructions carefully.  You choose the SSD as a target.  After the data is transferred from the HDD to the SSD, you can disconnect the HARD drive and start the computer.  It should start on the SSD.  Then, you can disconnect the SSD to the first SATA connector and move to another Bay HARD drive and connect it to another SATA port on the motherboard.  You can use it for storage.

  I like the SSD Samsung EVO.  Samsung offers its data Migration software to clone HARD drive.  In addition, they provide their software Wizard to optimize the performance of the SSD.  You can find all the software at the bottom of the page in the link I provided for the EVO.  The Samsung SSD were good about starting in HP computers without changing the BIOS settings.  You will need to buy an adapter to allow the reader to 2.5 "to fit into a 3.5 Bay".

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.