HP Jet 7 fails to start after the incomplete BIOS update

Similar Questions

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• Satellite L40 - 14 H - do not start after the successful BIOS update

  Hello

  I have Satellite L40 - 14 H which was working fine until I thought to an update of the BIOS will not hurt. Seems I was wrong.

  I downloaded the update to the BIOS, it unzipped in a folder and started the action.

  After a few seconds was asked to wait, and then after few more firm.

  After the reboot, I pressed F2 to enter the BIOS and check that it is version everything was fine, version 2.0 so was I left once the parameters.

  After that, nothing happened.

  I almost tried everything without success. Removed the power and battery power, put their back, but still no start. Just the light of the HARD drive lights up for a few seconds and the cd turns a bit, but after that nothing happens at all and completely the screen is black.

  I don't know anything else to try.

  Please let me know what that can do to restore its functionality without taking it to the service, I can't do it.
  I think that may not be cause of failure of the BIOS update I have seen it is the version and was right.
  Is it possible to reset the BIOS? I need to disassemble the laptop to do this?
  Let me know what to do, I have good experience in such things, but I can't understand this.

  Thanks in advance for any response.

  Kind regards
  Stefan

  Hello

  I agree with Akuma. It really isn't that you can do about it. BIOS problems are complex and cannot be set by the owner of the laptop. Believe me you need professional help with this.
  Contact the closest Toshiba ASP and explain the situation.

• Satellite A100 does not start after the wrong Bios Update

  Yesterday, I upgraded my BIOS of 1.90 to 2.20 for VISTA... now, apparently, I downloaded the BIOS bad a100 to my A100 (PAAS...)

  Now the computer turn on (no display) then a few seconds later stops offshore and turns on again (without interruption), I am under warranty (and the computer is in the store) but I was wondering what to do if Toshiba is not honor the warranty?

  Thank you very much for your help!

  Hello

  I'm sorry to say, but it seems that you don't have the choice.
  You can ask him authorized partner in your country for the help that I know, BIOS update errors are not covered by a warranty and you will have to pay a small fee for fixing.

  In the worst cases, the motherboard must be replaced:(mais peut-être avez_vous une évasion chanceuse et seulement la puce ROM doit être flashée à nouveau)

• Get an error 'he cannot read the file' in Windows media player after the recent bios update

  * Original title: windows media player cannot play the files after the recent bios update

  I installed the latest update of the bios on my Hewlett Packard Windows 7 and now windows media player comes up with an error message saying that it cannot read the file for each file that he used to play.  Is it possible to uninstall and reinstall windows media player separately from windows?  or y at - it a file update or repair that I can download to make it work again.  I don't get a codec error.

  Hello

  1. What is the full error message?

  2. What is the number of KB of the update of the Bios?

  Please follow the steps below and get back to us with the results.

  Method 1: Open the troubleshooting Windows Media Player settings Troubleshooter

  http://Windows.Microsoft.com/is-is/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Method 2: Uninstall and reinstall Windows Media Player.

  Step 1: Uninstall Windows Media Player.

  a. go to start and in the search type 'Turn Windows has or not'.
  b. click on "Turn Windows features on or off".
  c. find multimedia and uncheck the brand in the face of Windows Media Player.
  d. restart the computer

  Step 2: Reinstall Windows Media Player.

  a. go to start and in the search type 'Turn Windows has or not'.
  b. click on "Turn Windows features on or off".
  c. find the multimedia functions and place a check mark in front of Windows Media Player.
  d. restart the computer and check with the question.

  Turn on or off Windows features

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-features-on-or-off

  I would say that you can download the last packs of codec for Windows Media Player to the Internet and check out them. Make a search using your favorite search engine.

  Warning: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Let us know if it helps!

• Windows 7 does not start after the installation of updates - sounds familiar!

  Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

  Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

  Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

  Here's the resolution...

  I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

  My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

  Now my system is up to date with all windows updates and I'm able to restart without any problems!

  Close this message.

• Equium L350 - Vista fails to start after the installation of recovery

  Hello world

  I have an Equium L350 after an accident I couldn't restart my pc. I tried to solve by using the recovery f8 menu and it did not work so I contacted Toshiba and got a restore disc. I reinstalled from the disc, after the instalation it said complete installation but visa does not start.
  I get: Windows cannot repair this computer automatically click finished to turn off your pc

  After a format and reinstall my computer broken? He is 13 months here for out of warranty

  Hello

  Normally after the installation of recovery your laptop should work fine again.

  In my opinion, it could be a malfunction of the equipment. Did you test the HARD drive for bad sectors? You can do this with Drive Fitness Test: http://www.hitachigst.com/hdd/support/download.htm#DFT
  Download the ISO image and burn it to a disk. Then you can boot from it and test your HARD drive for errors.

  I also recommend to check the RAM for errors: http://memtest86.com/
  Memtest is a good diagnostic tool for the RAM.

  I hope I could help a bit. :)

• BlackBerry JDE fails to start after the installation of Simulator Tour 9630

  I use JDE 4.7.0 on Win XP + a bunch of simulators.

  After the Tour 9630 Simulator (v 4.7.1.40), I installed the JDE does not start.

  I tried to run ide.bat via command line - it does not give error messages.

  I tried to reinstall my JDE (with deletion of the dir of installation in order to remove settings from JDE is) - it did not help.

  I am now able to run the JDE again after that I uninstalled the Tour 9630 Simulator. But I really need this Simulator because I develop an application for the round.

  What could be the problem?

  Thanks to Marc post here the solution I managed to solve this problem.

  The solution is:

  1. install the Simulator
  2. Make a copy of its installation directory
  3. uninstall the Simulator
  4. manually create a new Simulator in JDE by using the copy of the directory

• Windows 2003 fails to start after the conversion from a virtual hard disk with vSphere Standalone Converter 4.0.1

  Hello

  I've recently updated my host to vSphere 4. I've also upgraded to vSphere Converter 4.0.1. However, when I convert a Microsoft Windows 2003 virtual hard drive in vSphere, the resulting virtual machine does not start. He gets just after the BIOS screen, then turns black with only a white line in the upper left corner of the console.

  I tried the hot and cold conversions. I tried changing the different settings of default conversion. I tried to remove the source machine and recreate.

  It worked well under ESX3.5, so I wonder what I'm doing wrong on vSphere.

  Any help appreciated.

  Thank you.

  In v4 disk are in SCSI format only.

  Probably also the source was in the SCSI format... so v7 to the IDE format give you not configured in the bootloader of the disks.

  André

• Windows Vista 32-bit is failing to start after the success of the recovery.

  Hi all, my apologies if this has already been covered in another post, I checked but I'm new here so might have forgotten.

  I have a HP Pavilion a6442a with Windows Vista 32-bit. A couple of weeks it froze, forcing me to maually shut down, and now it does not restart. It gets so far then goes to startup repair, which never seems to find no problem. I tried restoring the system (to several different restore points), conducted diagnostic tests, conducted tests of memory and hd and tried commissioning in all modes as I could: no problem can't find anywhere and I always had the same problem. Finally, I backed up my files and made a full recovery of the system. It said it completed successfully, I restarted to complete the installation of Windows, it gets "Please wait a moment while Windows starts for the first time... "freezes, restarts and then traced directly back to the start screen for repair.

  I am at a loss, I've done everything I can think. Does anyone have any suggestions?

  Hello:

  Have you added any hardware configuration inventory (other than replace the hard disk or add memory)?

  Do you have only the mouse, keyboard and screen plugged in when you ran the recovery procedure?

  If the answer to question 1, remove any material that you have installed that do not come with the PC and try to recover again.

  If the PC is recovering successfully, close and reinstall your spare hardware.

  If not, question 2, unplug anything other than the mouse, the keyboard and the monitor and try to recover again.

  If you continue to be confused and you can read all 25 characters of the product key of Vista on your PC case, you can make your own Vista installation media.

  It will be just a simple installation of Vista and no software other than the operating system will be included.

  You can install the drivers and software available to support for your PC and driver page.

  Link to the info below... click on the blue link of the reinstallation of Windows Guide PDF and start reading the news of Vista that starts on page 296.

  http://philipyip.WordPress.com/Dell-community-forums/

• Failed to start after the duplicate database dbconsole

  Hello
  
  The last time I tried to replicate a database on oracle database 11 g 2. Data source a sid is vvcoredb and database target a sid is orcl. I duplicated from VVCOREDB to well ORCL. I can access and query the database on ORCL. But I can't access dbconsole. I don't know why. I missed a few things?
  
  P/s: I database starting with the default command is: sql > startup.
  
  Anyone have any suggestions for me?
  
  Thanks in advance!

  See the emca command-line reference
  http://docs.Oracle.com/CD/E11882_01/server.112/e25494/dbcontrol002.htm#ADMIN13410

  EMCA - deconfig dbcontrol db | all - rest drop
  EMCA - config dbcontrol db | rest all - create

  Hemant K Collette

• Only get a blinking cursor when you try to start after the installation of updates

  Original title: blinking cursor when you try to start

  After installing Windows updates last night, our laptop Dell running that Vista gives only a blinking cursor when you try to start

  Hello

  1 update you tried to install?

  Step 1:

  You can check out the following link and try the steps.

  The update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista and Windows 7

  Step 2: When you're able to start normally, check the history of update to discover updates failed as a result of the article:

  See the Windows updates are installed

  Step 3:

  If there are updates failed, then try to download and install the stand-alone package with updates from the Microsoft Download Center.

  a. to download updates from the Microsoft Download Center

  b. Enter the item number in the field search and download the same.

  c. double-click on the downloaded file.

  d. click on run and follow the wizard to install it.

  Hope this information is useful.

• Reviews of Ubuntu does not start after the installation of updates

  I have a Windows 10 host and a guest Office Ubuntu 15.10. Ubuntu installs and runs fine until I have install updates, and then it gets so far through the boot sequence, but blocks trying to start the GUI.

  What should I do?

  Hello

  can confirm: after installing the last invited Ubuntu patches of the slaughtered 3.16.0-62 core during startup.

  Latest posts is: failed to start the vmware services.

  logfile VMware stops at the loading HGFS subsystem.

  To access the guest computer resolution: Boot with advanced options (hold SHIFT to start, until the menu loader grub is shown). Now select boot option (!) lower than 3.16.0 - 62.

  With 3.16.0 - 60, the guest operating system will start normally. Reinstallation or reconfiguration of the vmware tools don't fix this behavior. If something seems broken with kernel 3.16.0 - 62

  Any solution with core 3.16.0 - 62?

  Best wishes

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• ENVY M6 - 1184ca: 8.1 for Windows does not start after the installation of update KB2919355

  Updating Windows 8.1 KB2919355 has proved to be extremely problematic for me. When he was released at the beginning of 2014 that I was not able to get installed it with the exception of two occasions, the first being several months ago and the second time, a few days ago. I have constant pain to try to get the update of KB2919355 until recently. What finally got the update installed was opened as administrator command prompt and type the following commands,

  DISM/Online/Remove - Package PackageNameackage_for_KB2919355 ~ 31bf3856ad364e35 ~ amd64 ~ ~ 6.3.1.14 

  and then

  DISM / online/cleanup-image /startcomponentcleanup

  So now, the update of KB2919355 has been installed. Only one problem: like the first time I had the installed, Windows Update leave commissioning. As the HP splash screen that normally appears during the startup process appears after about 3 seconds, Windows displays an error Stop, and for a fraction of a second will display SYSTEM_THREAD_EXCEPTION_NOT_HANDLED error, which as I read, is related to the graphics drivers. The thing is, after the cancellation of the update (the computer in Mode safe start put Windows automatically uninstall the update and everything goes well after), then go in and uninstall the graphics driver, restart, reinstall the graphics driver and reboot again, and then reinstall the KB2919355 update, the problem recurs. I also tried to download and to install the new update of firmware for my particular DESIRE machine which was released a few days ago, but which has not helped either.

  I'm really stuck. I looked up and down, and I scoured Internet for anything that might help. I need to update KB2919355 be installed because without it, I can't book my free upgrade of Windows 10. This laptop is about 2 years and a half old now, so it fulfills all the prerequisites for Windows 10.

  Please do not suggest that I do a Refresh of the system or a system reset, as I have no way to back up my programs, that which some I would not be able to reinstall because I have more drives for some of my programs. Also, I can lose to save him for some of my games.

  When people ask me "What's up?", I always say 'the CAP '.

  So that seems to have solved the problem that is described in this post here. I followed the suggestion, which was to uninstall the driver, SPDT DuplexSecure (which has something to do with the SCSI devices, I'm not quite sure) using the SPDTinst (download here) and now it seems that Windows has started without crashing after installing the update KB2919355. I'll check my Windows Update history and see if it is there.

  Low and behold, a year to be really behind value is ultimately more. I have successfully obtained the update of KB2919355 works on my computer.