HP Officejet J6480: Start printer [J6480) with light turns off wireless]

Similar Questions

• Start button / stop flashing light turns off

  Original title: Power up

  When I turn on my Dell Demension E510, the power button flashes amber in color. I can't turn on my desk until there is a clicking sound or reset and the flashing light goes off.

  Hi HOWARD R Ruscin,.

  This seems to be a hardware related issue. Your best bet of contact would be the manufacturer to resolve the problem.

  Visit the following link to contact:

  http://en.community.Dell.com/

• HP Officejet 4620 e-all-in-one stop wireless print whenever it is turned off

  My HP 4620 stop wireless print whenever it is turned off, although it is connected to the network (by the results of the test network wireless, pass & the quality of the signal is excellent).  No troubleshooting - HP Print & Scan Doctor work there is no help, I have to uninstall & reinstall the printer each time to be able to print wireless again.

  I use it on/on button to turn the printer off, don't disconnect not.

  Please help, or I need to return to the store, this is the third time!

  I also had the same issue and after a few game it seemed to have fixed so here's what I did... Hope this helps someone else.

  -My printer is connected to my wireless network.

  -On my computer that I'm connected to the printer through the IP address 192.168.1.153... (Yours may vary) in a browser

  * You can find the ip address printers on the control panel of the printers by pushing the wireless button and pushing the ok option 1, it should appear with the intensity of the signal and the ip address is at the bottom.

  -Once I was on the Printers page in my browser, I went to the tab network at the top.

  -Then to Internet Printing Protocol section (on the left in the advanced settings)

  -On my own PPI was already on, but the location was empty I put a '1' in the location box and then applied settings.

  -C' is the only thing that I changed and now my printer is asleep as always, but when I print something from my iphone, mac or pc it wakes up and prints as it is supposed to!

  BTW before I went to the printer via the browser. I changed layout sleep in 15 minutes via the Control Panel on the printer itself, don't know if it helped the issue or not because I still had the problem of sleep after I set the timer to 15 minutes instead of 5 min. But I solved my problem after performing the steps above!

  Also note that on the one hand some ppl on here say it's a network problem or a router! This is NOT the case I never even tried these roads and I solved my problem only by changing the setting of the printer! I have not set a static ip address or something like that!  The above steps is things ONLY I touched and my problem is SOLVED!

  Router: NETGEAR AT & T 7550 wireless router/dsl Modem

  -Security: WPA2-PSK (AES)

  -Printer connected to the router via WPS (push button configuration)

  Printer: HP Officejet 4620e all-in-one

  Computer: Apple iMac OS X Version (connected to the network via wifi) 10.7.5

  Dell running Windows 7 server (connected to the network via wifi)

  Apple iPhone 4S (connected to the network via wifi)

• Why has my laptop started to randomly stop before turning off

  Original title: computer power questions

  Why has my laptop started to randomly stop before turning off? I had no problem with this computer at all for more than a year. I tried to run all the updates available, but of course, it turned off before she finished. Sometimes it will run fine then others that it is a nightmare. can anyone help please? I would be very happy to help!

  Hello

  Could be heat related - try using a small fan to blow into the air intakes to see if that helps.
  It is just like it loses power or stop it in the normal way?

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Remove the dust bunnies and clean the
  air vents. Check that fans are working (before and after opening the case). When your laptop on all the
  You can do is to reinstall the memory and clean the vents (still may try to add a small fan as a
  test).

  This sounds like material so if the above does not help you then probably need the help of a
  real computer store (not of leeks and glances at a Best Buy or other department stores) or the system
  Support from the manufacturer.

  ===========================================================

  Check with these utilities to see if information may be collected: BlueScreenView run to see if
  There were some BlueScreens and MyEventViewer at the time, check if the stop (or a little
  seconds before) see the event log contains useful information.

  It is an excellent tool for displaying the blue screen error information

  -Free - BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  and displays information about all accidents of a table.
  http://www.NirSoft.NET/utils/blue_screen_view.html

  -------------

  MyEventViewer can be verified at the time of the blue screen (BSOD) within a second or so of the
  time of the BSOD to provide more information about the possible cause - see TIP.

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the whole of the record-
  Set it for a bit before and after the time of the BSOD.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  ------------

  AppCrashView - free - a small utility for Windows Vista and Windows 7 that displays the details of all the
  application goes down has occurred in your system. The information breaks down is extracted from the .wer
  the files created by the Windows Error Reporting (WER) of the operating system component of each
  time that an accident has occurred. AppCrashView also allows you to easily record the list of accidents to
  text/html/csv/xml file.
  http://www.NirSoft.NET/utils/app_crash_view.html

  ------------------------------

  Also do this so you can see the probable bluescreens. (You may or may not be able to see
  them if they occur even after doing this according to the cause.)

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  =========================================

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  =========================================
  =========================================

  More if needed and you think that the closure could related to the Options of food or sleep.

  Check your settings (BIOS/CMOS) - usually F2 as you start - Wake on Lan, Wake on Modem and so on.

  Troubleshooting Windows Vista sleep and extended
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  May need to reset all to default power settings and then place back as you prefer.

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  Panel configuration-Control Panel Home view (non-conventional) in the top-right search pane
  type of hibernation - see turn Hibernate on / off

  May need to reset all to default power settings and then place back as you prefer.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• 10GBase-T module lights turn off after turning the power on switch

  I have a pc6248 with the latest version of the firmware and a 10gbase-t module which lights do not go after turning on the switch.  But if I do a "reload", the module lights turn off and works normally.  So there's something about switching on the switch that causes the module lights stay on and the module is not connect or traffic through until I do a 'reload '.  I have another module that works normally in the switch, so it doesn't seem to be a problem with the switch.  Has anyone else seen elsewhere?  Clues about what can happen?  Any help would be appreciated, thanks.

  I see, unfortunately there isn't really anything that can be done of these modules. No update of the firmware or something like that.  Having two of the same exact module, 1 works and 1 does not work, indicates a problem with the module. Is the module a recent purchase? If so, you can get toggled.

  With the defective module installed, if you issue a shutdown command and then a no shutdown interface command, behavior change at all?

• (Redirected) Power adapter green light turns off when the laptop battery is plugged into the laptop and does not load.

  Power adapter green light turns off when the laptop battery is plugged into the laptop and will not charge; If the laptop battery is not plugged into the laptop adapter it's still green and will charge the laptop.

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Tip: when you post a message, preferable to always include the computer model.

  Bev.

• After that update notebook bios don't start. It starts for 5 seconds and turns off several times

  Today morning I upodated bios hp Web site, mp model laptop computer is hp pavilion dv4 5009tx, bt after update it does not start. It starts for 5 seconds and turns off, and cela go pass away...

  Please suggest me what I'll do now.

  MY LAPTOP IS IN WARRANTY PERIOD. I bought this month

  Read the paper > HERE on the restoration of the BIOS.

• OfficeJet Pro 8620: Print borderless with Officejet Pro 8620

  Hello

  I recently bought a hp OfficeJet Pro 8620 and I'm testing now a few important functions for my business. One of them is printing without margins of leaflets in A4 format. But the problem is: even if I chose "A4 borderless" paper size and "photo paper" like paper it always prints a white border around entire page--so he is not chosen in the menu borderless printing. The flyers that I want to print all pdf format and print them with a program called "document viewer", but using another program for printing without margins such as gimp makes no difference!

  By the way: I'm (Lubuntu 16.04) Linux as an operating system, the printer is connected via usb and the driver that I use is "HP Officejet Pro 8620, hpcups 3.16.3.

  Please help me to find a solution to this huge problem, because printing flyers for my small business is one of the most important reasons I bought this printer for and I urgently need print flyers (without borders) for the weekend too.

  Thanks in advance!

  Hello everyone,

  It's me again. Yesterday, I solved the "problem".  The problem is that the image of the pdf file that I wanted to print without borders had the size 210 x 297 mm (A4), but I had to larger scale to 214.5 x 300 mm, 9 mm up to what he had the correct size for printing without margins (A4).

  Unfortunately, these strange dimensions does not exactly appear in the dialog box size media in settings print HP Tools program but rather to the dialogue of the PDF Viewer, if you select the paper type and paper size. I do not understand this, but I finally works, and that's all I wanted. In any case thanks for trying to help me!

• HP OfficeJet Pro 8610: Printer cannot connect to the new wireless network

  I got the OfficeJet Pro for a while and everything worked very well (including wireless printing from my Mac and iPad AirPrint). Yesterday, we got a new Modem Router (from Ubee). As I tried to connect the printer with the new network, I fail miserably.

  Here's what I've tried several times: on the small screen of the printer, I select: Network Setup > wireless setting > Wireless Setup wizzard. The printer seems to networks, find the network and asks me the password, I get the password (I did this several times, so no typos!). The printer then "trying to connect to the network"... then it crashes: for a very short moment, I get a blue screen with a white error code (not always the same, for example.) B3FF3802) and then the message "error in the printer, turn off the power, then press.

  I turned off the printer and turn it back on several times (incl. pulling out the power plug and restart after a while), but when I go through the steps above, but I just get the same endresult.

  I deleted the old network as I feared it might interfere with the creation of the new network. No noticeable effect.

  I printed the "results of the wireless network test," which confirms that "your HP printer is unable to connect to your wireless router. In the results of the diagnosis, he states that 'network name (SSID) was found - Fail.

  I quite understand the message that the printer detects the network and shows good SSID / network name. I thought to enter the SSID manually but can't find where I could do.

  I'd be very grateful for any suggestions on what could be the problem (I can't imagine that the printer would not work with a new router... I searched the internet and found stuff on 'Hello compatibility', but do not know which is the issue I'm facing.

  Thanks for your help!

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this post has instructions.

• HP Officejet 6500 a: printer will not connect to the wireless network.

  I got this HP printer for a while and it worked fine.  Our old router is out and we had to get a new one.  Installed perfectly and printer continued to work properly.  The password for the router was ridiculous, that's why I changed it to something much more simple to remember.  Since then, my printer will not connect to wireless internet.  I have a ~ and reinstalled the printer but still have the same problem.  I thought maybe to try the former password would, but who does not work either.

  Anyone has any ideas that might help before chuck it and go and get a new one altogether?

  Thank you.

  Easy things first.  Turn off the router and the printer.  Turn on the router and wait 3 minutes.  Turn on the printer and see if it connects to your router.  Status?

  If no joy, temporarily disable all security in the router.  Now try to connect the printer to your SSID not guaranteed without password.  Status now?

  If OK, go back and add WPA2-AES with your simple password.  Status now?

• L7680 All In One - scan light turns off before full page is scanned

  When I choose to scan or copy, my L7680 starts the function chosen, but after scanning about 3 inches of the page, the scan turns off light and the rest of the document will appear as solid black. Any ideas on what is the problem and how it can be repaired?

  Thank you.

  Hi there SLM64,

  Welcome to the Forums

  I noticed the problem you are having with your Officejet Pro L7680.

  I understand that you notice the scanner bulb turn off and it's causing most of your explorations or copies of out of the black. It is a hardware problem that seems as the scanner begins to fail. I have a guide below for you that means two things to try, however, if the guide does not solve the problem, I would suggest calling technical support of HP. They have an option of recovery for you to buy a new unit.

  A "Failure of the Scanner" Message appears on the all-in-one control panel and you can not scan, copy, or fax

  If you call in North America, the number is 1-800-474-6836 and for all
  other regions, click here: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html

  All the best,

• Problems with restart, turn off, finder app and desktop missing files

  I put my macbook (Pro 15 inch Retina 13 end) on 'sleep' last weekend and didn't use it for a few days. Came home and found that my office files have disappeared and the "finder" icon does not work and will not restart. Tried to download El Capilan to see if that helped - but that did not work, or the other. It seems to be downloaded, but accuse mac to OS X Yosemite than current version. When I try to download the OS X El Capitan again, he gets only to restart - which does not happen. In addition, the mac does not have to reboot or turn off the buttons. Any suggestions this is appreciated please

  Mac

  Reset the NVRAM/PRAM memory.  http://support.Apple.com/kb/PH18761

  Reset the SMC. Choose the method for "on Mac Laptops with non-removable battery.

  https://support.Apple.com/en-us/HT201295

  Boot mode safe. https://support.Apple.com/kb/PH21875?locale=en_US

  El Capitan

  Finder > Applications > install OS X El Capitan.app

  Double-click it to start the installation.

• Pavilion 15 laptop: Start button / stop does not turn off

  After the upgrade to windows 10, "sleep" mode did not work, however a windows update corrects this problem. The only problem I have seen today is that when I stopped my laptop the power button stays on your battery and I have to manually turn off (by pressing for 5 seconds).  What I do is turn on the computer again and stop it again, and then it turns off completely. I m afraid that force close down may harm the computer.  As info... I bought my laptop this year, came with windows 8.1.  Any help? Thanks in advance.

  1. Download version 9 or 10 of the Intel Management Engine Interface (MEI) driver.
     • Navigate to HP Software and Driver Downloads site (http://www8.hp.com/us/en/drivers.html) to find the last pilot approved for your model.  Filtrer filter by version, select Microsoft Windows 8.1 on the menu drop-down.  Find the download in the category 'Driver-Chipset'  If a pilot of MEI with a version from 9 or 10 number is listed, download.  [9.5.24.1790 version 1.5 M (http://ftp.hp.com/pub/softpaq/sp66001-66500/sp66228.exe) works for most models.]
     • If a pilot of MEI with a version from 9 or 10 number is NOT listed, download the driver appropriate directly from Intel (https://downloadcenter.intel.com/search?keyword=intel+management+engine).  [9.5.24.1790 version 1.5 M (https://downloadcenter.intel.com/download/23091/Intel-ME-9-Management-Engine-Driver-for-Intel-NUC) works for most models.]
  2. Download the Package of troubleshooting Windows 10 "show or hide updates" (http://download.microsoft.com/download/F/2/2/F22D5FDB-59CD-4275-8C95-1BE17BF70B21/wushowhide.diagcab).
  3. Change the Windows Update Services automatic (delayed start) parameter to the manual.
     • In Control Panel, select administrative tools, and open Services.
     • Go to Windows Update and double-click it to view its properties.
     • Click on stop to stop the service to run.
     • Change the Startup Type to manual, and then click OK.
  4. Install version 9 or 10 of the Intel Management Engine Interface (MEI) driver.  If you receive a warning dialog box about the replacement of a newer version of the software, accept it.
     • NOTE: You have NO need to uninstall version 11 before installing version 9 or 10.  The presence of a version of the driver is required to 'upgrade' (or demote in this case).
  5. Run the Windows 10 Troubleshooting Package 'Show or hide updates' and hide the updates of the Intel Management Engine Interface (MEI) driver.  (This will block your system automatically reinstall or display of updates for version 11 of the pilot).
  6. Change back the setting of Windows Update Services to manual automatic (delayed start).
  7. Restart your computer.
  8. Rejoice!  You can finally sleep and stop again.

  -DanG

• Help me with the "Turn Off screen" app

  Hello world!

  I start developing BB10, I want to make a request, there can turn off the screen with 1 button icon on the screen.

  How can I do? where should I start from?

  Hi dominic9, welcome to the Forums of the Dev Support.

  What you're trying to do can be done in 10 BlackBerry, there is no way to stop the screen programmatically.

  Your application can set its own brilliance, but it will only apply to your application (brightness will return to normal when you exit / minimize the application), but even if the brightness is set to 0, the screen will be WE and touch screen will result in key events, which means that the user will continue to interact with the screen, but he won't see what it does.

  Use this C API to control the brightness of your application:
  https://developer.BlackBerry.com/native/reference/core/com.QNX.doc.screen.lib_ref/topic/screen_set_w...

  Code snippet:
  https://github.com/RodgerLeblanc/TheUnexposedAPIs/BLOB/master/src/backlight/backlight.cpp#L85

• HP officejet 6500 a printer works with Mac Mountain Lion but scanner is not

  had a 10.6.8 imac and I used and scan with hp printer HP officejet 6500 a.

  Just got a mac mini 10.8.4 and the wizard migration used to move all my programs and information.

  The printer works just fine but the scanner does not work.  When I try to start the scan by pressing the printer screen it says computer no. detected as part of the message.

  If I click on the scanner icon on my dock it says

  HP Scanner 3 cannot be opened locks of Aproblem.  Check with the developer to make sure that HP Scan 3 works with this version of Mac OS X.  You may need to reinstall the application.  Don't forget to install the updates that are available for the application and OS X.  There is also a report I can click on and sent to apple.

  I got a free mini mac technical support - they helped me with the migration, and then a few days later, I called for what they help me with things that were not working as before.  All resolved but this.  They said contact that HP may be there is something that I can download to make the scanner work?  Hope I don't have to buy a new printer.

  Thanks for the tips .

  Hello

  Yes, go ahead and put this folder in the trash, I would also suggest restarting the Mac and repair disk permissions in order to avoid any possible permissions errors that can impact on the installation:

  Hello
  Follow the steps below to repair disk permissions:

  1. open the Applications folder.
  2. go to the Utilities folder.
  3. double-click on disk utility.
  4 Select the hard disk that contains the boot volume.
  5. go to the first aid tab and select Repair disk permissions.
  Note: This process may take several minutes depending on the Mac and the amount of the permissions that need to be repaired. The progress log shows when the process was completed.

  Once you have finished my steps above to reinstall the software.

  Shlomi