HP pavilion a6614f not start

Similar Questions

• HP Pavilion will not start? help please.

  A few weeks ago, I had a pavilion dv6700 out of my brother, when I turn it on hp invent comes on the screen and shortly after it turns off then try to start over, he repeats this process again and again, sometimes after that it says "not found opperating system".

  Ive tried a system restore and also led a diagnosis whose results were, for the primary hard drive no self-test "no IDE device".

  and 'transmitted result' memory test any help would be great thanks in advance.

  http://h10032.www1.HP.com/CTG/manual/c01295877.PDF

  {+} Removeal and replacement procedures

  [+] component replacement procedures

  Click on HARD drive

• HP Pavilion does not start after upgrading Windows 10

  (Sorry for my bad English)
  Last night I started to update my HP Pavilion Windows 8.1 to 10, but I have a problem, because today, in the morning, the update was 99%, and it ended, just after I have shut down the computer and is going to school and when I got home, I turned on my HP and the problem was that the HP logo appeared and he began to load , but he didn't only show anything else than that, so I thought I'd let load after 3 hours, it was still loading and it was reseting every 5 minutes and now I just can't not try windows 10. Help?

  Hi there @lmao1,

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that once you tried to upgrade to Windows 10, now stuck on the HP Logo at startup.

  If the computer hangs at the HP logo screen, try to clean the vents from the computer to the air and then restarting the laptop.

  Please note , remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  Have you tried a hard reset?

  Have you tried to Test for hardware failures?

  Are - that you receive error messages or error codes?

  You happen to see a blue "option ' screen at all? '"

  Follow these steps to remove and reinsert the memory modules for troubleshooting:

• HP Pavilion will not start

  I have a Pavilion P6774Y desktop computer.  A few days ago, he would not wake up.  I turn it off and be restarted using the power switch and the blue HP screen appeared, followed by a black screen with a cursor blinking in the upper left corner who disappered after a few seconds.   After repeating this a couple of times, I swapped the monitors and HRT has not set.  Then I unplugged it, let it sit for a few minutes, plugeed it it and restarted and it started normally.    Since then, the same question has occurred several times.   Sometimes it reboots normally, other times, I get the black screen.  Sometimes it takes to unplug and reboot several times for it to start.  Does anyone have any suggestions where to look for a solution?

  TF1965, welcome to the forum.

  There are two possibilities: 1) a lack of power supply unit (PSU) or 2) a hard drive failed.

  Here's a guide to troubleshooting of the PSU.  You can test the hard drive by using the Test SMART in BIOS.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion will not start past blue hp invent screen

  My computer does not boot past the blue hp
  Invent the screen. I took the sides off the computer. I started and I realized what was the noise that I heard and whence he came. It's the hard drive makes a noise like a fan starting then a rattling noise. Then it stop trying to load and is repeated several times, then closes. I unplugged the power supply for the drive hard drive now it
  take care when I unplug it but I can't do anything without hard drive.

  Your hard drive has failed. If you are still in warranty, contact HP to send a new hard drive. If you are out of warranty, it will be much cheaper to buy a retail hard drive to replace the original. Hope you have a value recovery disk?

• Pavilion does not start

  Hello

  My Pavilion (3 years old/Vista/2 hard drives) locked - no response from the mouse/keyboard, couldn't ctrl-alt-delete.

  I forced to close (and hold the button), and now it does not restart.

  When I turn it on, the lights come on and the fan comes on, but no disk activity hard and nothing - not even a flicker - on the screen. I plugged it up to an old VGA - nothing.

  It is a model of 2 hard drive, and I'm sure that came with no boot CD (I have an old XP CD - worth a try to boot from that?)

  Any suggestions? Motherboard failure likely? I can't point diagnostics running, so I send to HP?

  Thank you very much

  Answered my own question.

  I called local repair guy and he said to remove the battery for an hour, then restart with just the power supply. I did and it restarted.

• 6746c Pavilion: my Hp Pavilion will not start

  I have a Hp Pavilion desktop computer that is running Windows Me on this subject. I had the computer since 2000 I only use it for computer games now. I've never had a problem with this computer before, but recently it started having a problem. When it starts it only starts up only Hp Invent screen and does nothing else. I started using another keyboard and mouse for him.

  HP Pavilion 6746c

  After doing some tests, is the keyboard that was causing the end Ill have to check the goodwill of an older keyboard.

• HP Pavilion will not start the power upward

  I have a HP Pavilion (prod. # GG753AV #ABA) running under Windows 7.

  Power on, the switch lights up blue, fans are taking place but not boot upward and no display

  I tried unpluggin keyboard etc but no luck

  Thanks for any help

  Thanks for getting back to me!

  Make sure that the monitor is on the correct input/source. On the monitor, you should have a Menu button or a button input/Source. The Source of entry/must be set to VGA. If the monitor is set to a different port like DVI or HDMI type, it might be initially to go to sleep because it does not detect plugged into ports. Check and double check the input source.

  Also try reinstalling the RAM, which is just out the RAM and put it back in. If you have 2 sticks of RAM, you can also try to just put one in at a time in each slot to see if the screen lights up.

  I hope this helps. Let me know what you get results.

• HP Pavilion will not start, has horizontal lines on monitor - HP Pavilion Elite M9280a

  I tried to start my computer yesterday and I had a brief message 'Error in Vista' then - my computer would not respond.

  The monitor has just shown the colored horizonal lines.  Then, I rebooted the computer.

  Since then, I can't reboot my computer at all however, I can get into safe mode to connect but remain - lines horizinal who won't go away.  The icons are much larger in safe mode too.

  When I try to log in normally, the system will repair mode and finally displays the following message:

  ' Start can't fix computer automatically "I went to see the details of the problem and this will display:

  Signature of the problem

  The Startup Repair V2 problem event name

  Problem signature 01 Auto failover

  02 6.6.6000.16396.6.0.5001.18000

  6 03

  04 131074

  05 no cause root

  06 no cause root

  07 0

  2 08

  WRP 09 repair

  2 of 10

  6.06.000.0.00.256.1 OS version

  Locale 1033 ID

  I did start diagnostic tests and everything seems ok, but the computer doesn't not recogise my graphics video card.  The system, it shows the video card - VGA video controller - PCI Bus 2 - device 0, function 0.

  Can someone help me please!  Products listed below

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay?javax.portlet.begCache...

  Hello

  Technical page in your PC Watch: the Nvidia GeForce 8600 GT, or integrated graphics. You can check which graphic solution you have?

  You can see the desktop when it is in safe mode?

  Try the safe mode with networking enabled.

  A position that interests you, your Version of the OS (6.06.000.0.00.256.1) indicates you are running the original version of Vista. You must also upgrade Vista to Service Pack 2 (6.0.6002).

  If you can not download the drivers in safe mode with network, can you download the driver on another PC and save to disk?

  While in safe mode try to remove the possible corrupt driver using Control Panel, restart and see if Vista will load a generic graphics driver. Then, you should be able to download and install the appropriate driver.

  Jaco

• HP Pavilion will not start. Password Startup requirements.

  I have a ho27c model 23 H P Pavilion all-in-one number.  After an altercation with a crook of phishing, I can't get starts the request a password at startup.  After several tries, I get nothing, but demand repeated password.  I never opened a session as an administrator and has never seen it before.  Can anyone help?

  Product number is: F3D92AA #ABA and the model is: 23 h 027 c

  Thank you...

  ... LWMc

  It is always helpful if you specify the operating system installed.

  You have two options.

  Download a stand-alone antivirus\malware\adware scanner of a real antivirus company.

  Search for your game of recovery disks and perform a factory image recovery.  You can also do this from the power on with a F11 key. You is probably the best option.

  Once you got make sure that your PC and install a highly rated internet protection suite. Freebie antivirus programs are no help when it comes to rogue virus and malware such as you seem to have picked up. I prefer ESET Smart Suite and Norton Internet protection.

• My Pavilion does not start

  Error message:

  GLQ7JM - K 5, 1682 - XD0141 - 60RE03

  Hello

  The player at the link below is an example of one that would be perfect for your laptop.

  750 GB hard drive for laptop.

  The procedure to replace the hard drive begins Page 55 of your & Maintenance Guide.

  Once this is done, simply use your recovery DVD to reinstall the operating system on the new drive - a guide on this procedure can be found here.

  If you do not have your recovery discs, you can order a replacement set using the link below.

  Order HP recovery disks.

  If you have a problem with this link, order them directly from HP.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• Pavilion 15-p027tx: Beats Audio not start on windows Startup

  I updated my Hp Pavilion windows 10 p027tx when windows 10 has been released. But 2-3 days before I updated my drivers little to the last version that was available. I've also updated the audio driver realtek. But the problem is after update, Beats Audio does not start on starup windows. Beats Audio is still there but I have to start it manually by searching on it. Earlier, it allows to start in backgroud with an icon in the system tray. But now it doesn't. I have to start it manually. All the solutions to this?

  Hello

  Another option would be to add the missing registry key which you can follow these steps.

  First, hold down the Windows key and press R.  In the run window, type : starting the interpreter, hit enter and then delete the boot entry you added earlier.

  Before you begin, click the Start Menu, select settings, select system, Notifications & actions select on select icons appear in the taskbar - make sure that that there is not an entry for "Realtek HD Audio Manager" which is just off."

  According to what you find, follow these steps.

  1. if there is an entry for "Realtek HD Audio Manager", set it to On and restart the computer and see if it fixed the problem.

  ***********************************************************

  2. if there is not an entry for "Realtek HD Audio Manager", hold down the Windows key and press R.  In the run window, type regedit, press ENTER, and then click 'Yes' to the uac prompt.

  Go to the following.

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run       (click on Run to make sure it is highlighted ).

  In the larger right pane, right-click on an empty area, move the pointer over new, and select string value.

  Name RTHDVCPL and press ENTER.

  Now, do a right click of RTHDVCPL and select Edit.

  Copy the entry below and paste it in the "Value data" field

  "C:\Program Files\Realtek\Audio\HDA\RtkNGUI64.exe" s

  Click Ok to save it.

  Close the registry editor and restart the laptop.

  When windows has reloaded, click on the Start Menu, select settings, select system, Notifications & actions select on select icons appear in the taskbar - make sure that the entry for "Realtek HD Audio Manager" is set to one.

  Kind regards

  DP - K

• HP Pavilion a6040a will not start

  Hi guys,.

  My Pavilion a6040a desktop running Vista home, does not start. All I get is a blank screen and a beep code (1 short, 1 long, pause, repeating endlessly). I can't run any recovery CD and I got up to the part where I have to take part in the troubleshooting guides (http://support.hp.com/us-en/document/bph07107). However, I do not trust myself to remove, and will send a Tech if there is anything else I can do to solve the problem.

  What happened in head upward to the accident:

  Was functioning normally, do not try anything too demanding (just updated the client Java but I don't think that it would be the cause?)

  Had a BSOD, restarted in safe mode, can't find the cause so restarted in normal mode to connect to the net.

  An another BSOD a few hours later, restarted directly in the system recovery to run a diagnostic.

  During the tests, the screen locked completely, and I had to force a shutdown.

  Following this accident, the computer was unable to restart (see above).

  Blue screens came too fast for me to read, and the error code that came after the first BSOD has been saved on the hard disk, which I cannot now access. If there is any other information that might help, I will try and provide them, keeping in mind, I can't have the system running at all to check the news!

  Any help is very appreciated. My partner has an assignment for her master's degree due to a week and really needs the computer in place and running

  Thank you!

  Unplug the computer and open the computer and remove and reinstall the memory. It is as simple as simple can get.

  Simple directions:

  Open the case.

  http://support.HP.com/us-en/document/c00968217

  Installation of memory.

  http://support.HP.com/us-en/document/bph03886

  Even if you have the open computer take care of blowing dust around the CPU. Just look at the pictures in the link I sent. It could be that a fan does not spin also. Before you replace the cover, Plug and turn to see if fans turn.

  Message edited by dmhoo29 on 03/16/2009 01:13

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Pavilion HPE H8-1121: Pavilion HPE H8-1121 - new graphics card + power supply does not start after screen HP (Revisited)

  I have the same problem as this post 2013!  Ouch. Pavilion HPE H8-1121 - new map chart + power supply, does not start after HP screen.

  I installed a new power supply (Seasonic 620W), which works well.  I also installed a GTX 660Ti last year and it was works fine as well.  I recently bought a ZOTAC GTX 970 and attempted to install it, but it will not go beyond the blue HP screen and I get the same code of beeps (1 long, 3 short), who, seems, suggests that the video is not initialized.

  My BIOS date is 2011.

  Where can I find an update for this?

  I'm also using Windows 10, which I found on the HP site is not tested on my model and would probably not favourable to good use.  Should I do back up to 7 or 8?  and then update the BIOS?  Y at - it a update for my BIOS and where can I find.

  In any case, I hope that this is a solution.  Again, this is not a bad machine to be 5 years old.

  Thanks for any help!

  If the video card that you have purchased dose not a legacy vBIOS it will never start. An update of the BIOS doesn't solve that.

  It is likely that your new video card has a vBIOS UEFI and that only is for the PC motherboards newer than yours which have a UEFI BIOS. Your motherboard has a legacy BIOS. 2012 is the year of model when the UEFI BIOS more or less became the de facto on motherboards standard.

  I return it for a refund. Find the candidate of video cards that support the old BIOS. It can be inherited only or switchable vBIOS (legacy or UEFI) vBIOS.  I suggest looking at the site of Sapphire Technology. ZoTac is not known to provide enough information about their video cards in the way. You upgrade a pre-built desktop PC and it's different and a little more difficult to set up a DIY PC. I looked at the site of Zotac and see that nothing is said about their video vBIOS cards.  I would return to the map.  Carefully read the specifications of the video card. A candidate for your motherboard card must have inherited vBIOS support or simply, it won't work.

  ZOTAC (they don't say anything about their product vBIOS)

  https://www.ZOTAC.com/us/product/graphics_card/GTX-970-amp-extreme-core

  Sapphire Technology

  http://www.sapphiretech.com/catapage_pd.asp?cataid=305&lang=eng

  Because you look at game with 4 GB cards. Take a look at the following map. It has a double vBIOS. legacy and UEFI. http://www.sapphiretech.com/productdetial.asp?pid=640A98CD-0CF0-4191-B75C-CA2800111ADB&lang=eng