HP Pavilion dv4 stops unexpectedly

Similar Questions

• HP Pavilion DV7 stops unexpectedly

  Hi all

  A few days ago, I was looking through random Internet when my HP Pavilion DV7 stops suddenly. I turned on and it loaded on the Windows screen and then off again. I removed the battery, a memory (I have 2 DIMM 4 GB) and put back the battery and the other DIMMS in but the problem remains. It's a very strange problem - when I press F2 to enter the memory test, it starts to scroll a memory check and then turns off again. When I try to start it in recovery mode or in safe mode also stops. I don't know if it's a hardware or operating system problem - of ideas?

  OK, thanks for your help

• Windows Resume Loader black screen on HP Pavilion dv4-2145 dx laptop Windows 7

  I have a HP Pavilion dv4-2145 dx laptop with Windows 7. After pressing the button "on", the logo operation windows says its "recovery" windows, but a black screen titled "Windows Resume Loader" appears with the following message:

  The last attempt to resume the system from its previous location failed. Attempt to resume again?

  With the 2 following options:

  1. continue with system summary, (which does not work and I end up with the resumption of the "Windows" followed a blank black screen...)

  2 Delete restoration data and proceed to system boot menu (I haven't ' truei stops because I wasn't sure what that meant)

  But I managed to go to the reviews section diagnostic systems and it seems that he pass all 5 of the test, including hard drive and memory, poster, etc. So I don't know what the problem...

  Please notify.

  Thank you very much!

  Hello

  I think that in this case, you will have to choose the second option - "Delete restoration data and proceed to system boot menu" and see if that fixes the problem.  If all etc. documents you had open before hibernation were saved, then you should not lose anything.  If there are unsaved changes (for example if you have added to a document), the file will be to the point that his last record and you lose additional data.

  Kind regards

  DP - K

• HP Pavilion dv4-1548dx Entertainment Notebook w / win7 crashes on logout...

  Hi all

  I have the HP Pavilion dv4-1548dx Entertainment Notebook w / 4 GB of DDR3 RAM and erased the computer and installed a full charge of Win7 Ultimate 64. I installed all the drivers concerned on HP page.

  When I stopped, my computer sometimes freezes on the pages of Win7 "Logging OFF... "and while the icon of the ring runs very well, nothing happens and sometimes I have to make a hard closed down by holding the button for 4 seconds power about.

  I have a few additional programs installed, would highlight Adobe CS3, ZoneAlarm Internet Security Suite, and Office 2003.

  Anyone else experienced this or have any ideas?

  Thank you!

  Thanks for the reply. I note that my problem seems to have disappeared on its own. the only thing I did was to reinstall the wireless drivers, but don't know if it was the solution. It seemed, to the contrary, go in as a result of various windows updates, but it may have been the driver update/reinstall wireless network.

• HP Pavilion DV4-1125nr cannot start after the update/update BIOS version F.12 to d.55

  System: HP Pavilion DV4-1125nr PC Notebook

  Product #: FR922UAR #AB

  The system board ID: 30F7

  Version of the BIOS (before the update): F.12

  OS: Windows 7
  

  I tried to update the BIOS to d.55 which was provided by HP. After the successful installation the closure of new windows BIOS correctly. I restart the PC, HP Logo appears and then nothing happens. The operating system do not load or start at all.

  I also tried to boot using the Windows 98 Second edition CD (to charge BACK), but it did not work.

  Please help me...

  Fortunately I found a Solution to this problem.

  Here are the summaries (and modified according to my needs) the steps that I've taken of the following thread:

  http://h30434.www3.HP.com/T5/notebook-hardware/dv4-1140GO-won-t-boot-after-flashing-latest-BIOS/m-p/19698#M2730

  1. go to the hp site and download the correct version of your BIOS. In my case it had to F.12. Why not the latest version? Because there is no guarantee that the last one will work for you, know after measures.

  2. go where you downloaded the file and using 7 - Zip (or tool of your choice of course) unzip the contents to a folder of your choice. We'll get to that later, so keep this file open.

  3. use 128 MB or no matter what key-USB USB key (the smallest, you might find, because they said the smaller the better ) and reformatted to FAT or FAT32 click with the right button on the drive by clicking on "format".

  4. now that my USB is ready, go back to the folder where you extracted the file to update the BIOS (always open to the right of the folder?)

  "5. If you have the graphics card Intel integrated like me, copy the ' 30F7F12U. FD"of the key USB and RENAME the file '30F7F12U. FD' at '30F7. BIN ". Remember that this name calling to order "DV4-1125nr. If you have a different motherboard, the system or the BIOS, the name must be determined according to the.

  The next steps are exact 0.0 as follows (the link of a full detailed discussion is provided below), I simply numbered:

  6 unplug the adapter from the laptop.

  7 remove the battery from the laptop.

  8 insert the USB key into one of the USB ports on the laptop.
  Does not seem to matter which.

  9. press the 'Windows' key and the 'B' key

  10. connected to the power adapter.

  11 press the 'Power' button on the laptop.

  12. when the LED is entered, letting go of the power button / stop and the two keys down earlier.

  13. After about 10 seconds the notebook started to read the USB key. While searching for the file, the laptop beeps every seconds.
  The number of beeps varied, depending on what size of the key USB has been and
  the number of files on the USB key, a single beep for many.
  If the file was not found, the laptop will restart and try again.

  14. If the file is found then it took about 12 seconds for the laptop to load. No beeps sound not heard during the loading time.

  15. when it is responsible for the laptop has started flashing, indicated by beeps every 2 seconds. It took about 32 seconds.

  16. about 5 seconds after the ringtone had stopped off the laptop computer.

  First I update my pc with the last BIOS (F.66), but did not work for me (operating system not loaded after HP Logo ). So I decided to go back to the old F.12 (the version that has been shipped when the laptop was purchased) according to the procedure described above. But the problem is where to find version F.12 as HP currently provides links only for the version of the BIOS F.66 to d.55 (in the drivers from the hp support site section)

  Fortunately, I found a direct link to this version F.12 in the next thread.

  http://Forum.NotebookReview.com/HP-Compaq/304332-C700-CQ40-CQ45-dv4-dv5-DV6-hdx18t-Insyde-BIOS-recovery-using-USB-thumbdrive-2.html

  F.12 version:

  FTP://ftp.HP.com/pub/SoftPaq/sp40501-41000/sp40749.exe

  This was F.12 and worked for me. Thank God Almighty I return my PC.

  Thanks to all who contributed in the discussions above.

  Kind regards

  -gmuhammad.

  If you think that this post has helped you, then please give KUDOS *.

  Close the thread (Accept as Solution), if your problem is solved *.

• Blue screen on HP Pavilion dv4-1115ef

  Dear all

  I have HP Pavilion dv4-1115ef laptop.

  It was working fine. I have properly stop but the next day that I was not able to start my laptop.

  There was a message that there is a problem and start the machine in normal mode or initiated a start.

  Start mode, there was blue screen, but I'm not able to start my laptop.

  I have a lot of data that I want to retrieve all the data.

  Please suggest me the best option to get my phone in workng position without losing any data.

  Thank you very much in advance.

  Thank you very much.

  I'll try that.

• leader revovery pavilion dv4 1225dx

  My pavilion dv4 1225dx stopped randomly start, showed a blank screen and the caps and scroll lights were blink every few seconds. What I've read, it is unfortunately a major problem. I tried a hard reset, taking and in the stack, the stack of the RTC, try different combinations of these two modules and WLAN module to see if the computer should start without it. Nothing has worked.

  I understand that my computer is done at this stage, but I need to get the files out of it. Can I use a USB adapter cable to transfer the files from my hard drive? If so, how?

  -Desperate and tired-

  Hello

  Probably your best option is to remove the hard - see Page 68 of your Service Guide & -place it in an external enclosure (an example of what you need is on the link below), that connect to another PC and see if you can access your files.

  External 2.5 HARD drive caddy ".

  Kind regards

  DP - K

• HP Pavilion dv4 problem of disk controller!

  Hello, I have a Core i5 Pavilion dv4, wich is recently have frozen, and then a BSOD appears with stop 0x000000F4. I checked for software issues, but everything is normal. I ran the memory and the disk self-test with results 03F0 in two tests.

  I noticed that when I do the computer work stronger than normal (e.g. a 6 GB on an external disk file copy), or as when installing Adobe Master Collection CS5, the computer freezes at a part of the installation and then the HARD drive is not recognized by the BIOS, so I have to on your computer (then turn on turn off).

  After X times to get the same question, I look for the events in the event viewer, I get only an event source 'Disk', with the comment «the driver detected a controller on \Device\Harddisk error...» "blah blah blah... This event is coded: 11.

  What could be?

  I also have a problem with the WebCam, it is not recognized by the software.

  Help! Please...

  $ $ DJ-JaaM

  Hello

  03F0 is a failure of the bios hard disk test, you may well need to replace.

  It may be useful to check the following running.  Click on the Start Menu, computer, left click Local disk C once to highlight, right-click Local disk C and select Properties.  Click the Tools tab and then click on the button "check the drive for errors.  In the next window make sure that both boxes are checked, then click Start.  Part of this process will require a reboot to check the disk.  After the restart, as Windows checks the HARD disk, keep a watch for the number of defective sectors found.

  Kind regards

  DP - K

• Looking for parts for HP Pavilion dv4-1155se

  I have a HP Pavilion dv4-1155se laptop which works very well! No problem at all... except for one thing. One of the children fell on the right rear corner and broke the monitor casing and bent the hinge. The LCD still works fine, but it is only half attached the bottom of the case.

  I need to find replacement parts at reasonable price. I think I would need the largest part of the whole of the screen under the screen itself. This is the model of "be" with the black and blue case graphics on it. I would get the same thing if I can. Anyone know where to buy these pieces for a good price? Or is there a list of part numbers that I could do a google search for? All I could find so far are LCD screens that I don't need.

  http://h10032.www1.HP.com/CTG/manual/c01597750.PDF

  Here's the manual for your interview with reference numbers.  See if that helps.

  I've been on ebay see what would correspond to your computer.  There are a lot of things out there.  For most bronze. A couple of black people.  There is an a black right now that the owner spilled vodka top and it has stopped working. But the case is perfect and it's cheap.  You might want to look around on ebay in the components of the computer.  You might not get the blue graphics.

• Recently upgraded to El Capitan, I had that problem for Mail stop unexpectedly when I saw some posts.  I followed the steps and was able to remove the trouble messages.   Now I can't restore the mail window message viewer component.

  Recently upgraded to El Capitan, I had that problem for Mail stop unexpectedly when I saw some posts.  I followed the steps and was able to remove the trouble messages.   Now I can't restore the mail window message viewer component.  When I try to catch the separator bar to go back to the left, only half of the small arrow icon and line appears, and it cannot be moved.   Can open the message by double clicking a message viewer.

  Hi there, alicefrompa!

  Thank you for using communities Support from Apple. From your post, I understand that you do not see the Message Viewer box which allows you to read your e-mails; only see you the Inbox that includes a brief overview of the message and are unable to restore access using the separator bars. I have had this happen to my own Mail app and am happy to let you know how I could fix!

  You are really on the right track - you want to roll your mouse over the divider between the Inbox and sections Message Viewer (which should now be on the extreme right edge of your mail window) and drag it to the left.  When you click on the receipt/Message Viewer box, the cursor turns into a line continuous black with a single arrow pointing to the left. When you see the cursor change, click with the left button of the mouse and (while holding down the mouse button in) drag the combination line / arrow to the left. You may need to drag a little further than before to get it. I had to hang mine almost completely in the middle of my Mail app before the display of the message box appeared.

  From there, you should be able to adjust the boxes to your widths you want as expected.

  If you are still not able to get the display of the messages visible after have try this, here are a few more things that you can do.

  1. Press command + O on your keyboard.
  2. Exit the Mail application, and then press on and hold the SHIFT key on your keyboard while reopening.
  3. Restart your Mac by selecting the menu  Apple in the upper right of your screen restart from the menu drop down.

  See you soon!

• HP Pavilion dv4-1120br: doubts about the BIOS update for my model with the operating system current instaled.

  Hello

  I have a HP Pavilion dv4-1120br, I know that this model of HP laptop is old, but I instaled the 64 bit of Windows 10 on my machine and saw that my BIOS is version F.30 and the last of them available on the site of HP F.66 has.

  The problem is that this model is not suport for Windows 10 because, as I said, is too old. Can I download and run the update of the BIOS for Windows 7 64-bit available in the Web site, or I need to downgrade my OS to Windows 7, update the BIOS and then pass it back to Windows 10?

  Thanks for the help!

  Cantarino

  Hello;
  
  Let me welcome you on the HP forums!
  
  Your second proposal is correct - as the updates to the BIOS on the HP site are specific to the OS version and if you try to run one for Win7 in Win10, it will refuse to run.

  Good luck

• How to capture a screenshot on my HP Pavilion dv4 laptop so I can paste to word? Thank you!

  How to capture a screenshot on my HP Pavilion dv4 laptop, so I can paste to word? Thank you!

  Hello:

  You have a print screen button?  Probably abbreviated. Prnt Scrn

  You may need to use the Fn + the print screen key if it is combined with another article on the same key.

  Paul

• Pavilion dv4: problem in installing drivers

  Hi everyone, I am facing a problem by installing the following drivers. Please help me. Thanks in advance.

  Notebook: pavilion dv4
  OS: Windows 7 Ultimate

  1 standard VGA Graphics adapt - version: 6.1.7600.16385
  Hardware ID: PCI\VEN_1002 & DEV_6741 & SUBSYS_1646103C & REV_00
  PCI\VEN_1002 & DEV_6741 & SUBSYS_1646103C
  PCI\VEN_1002 & DEV_6741 & CC_030000
  PCI\VEN_1002 & DEV_6741 & CC_0300

  2. Ethernet controller
  PCI\VEN_10EC & DEV_8168 & SUBSYS_1646103C & REV_06
  PCI\VEN_10EC & DEV_8168 & SUBSYS_1646103C
  PCI\VEN_10EC & DEV_8168 & CC_020000
  PCI\VEN_10EC & DEV_8168 & CC_0200

  3 PCI Device-
  PCI\VEN_10EC & DEV_5209 & SUBSYS_1646103C & REV_01
  PCI\VEN_10EC & DEV_5209 & SUBSYS_1646103C
  PCI\VEN_10EC & DEV_5209 & CC_FF0000
  PCI\VEN_10EC & DEV_5209 & CC_FF00

  4 unknown Device
  ACPI\HPQ0004
  * HPQ0004

  Hello:

  What is the complete model number or the product number of your laptop?

  Many products are on the label as well as the serial number.

  Other than graphics, here are the other drivers you need...

  Ethernet: 3rd driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 13 & PFid = 5 & Level = 5 & Conn = 4 & DownTypeID = 3 & getdown = false

  PCI device:

  1 driver on the list...

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 15 & PFid = 25 & Level = 4 & Conn = 3 & DownTypeID = 3 & getdown = false

  0004:

  This will install HP 3D DriveGuard, which offers protection for internal laptop disk drive if the computer accidentally falls or suddenly hits another object. This package is available on mobile phones supported with supported operating systems.

  File name: sp53462.exe

• AC100 - the process android.process.acore has stopped unexpectedly

  Our AC100 suffers from frequent and annoying messages: the process android.process.acore has stopped unexpectedly (well it is said in Dutch, so I hope that the translation is good). After googeling I found many people with the same problems (but for other devices as a computer of Toshiba), and it seems that the only solution is to reset the original settings (after having a back-up).

  But since everything downloaded widgets and applications will be gone then, I'm looking for another option. Does anyone have any experience with this message? How you solve the problem?

  And who knows how starts this problems?

  Hello

  I also recommend the return parameter of the Android to the factory settings. The widget could be saved on external source before setting the notebook to factory settings.

• Cannot install driver for hp pavilion dv4-2045dx cd player

  Computer: HP Pavilion dv4 2045dx using Windows 7 (64-bit)

  I currently have problems with my computer's CD drive.  He has been unable to read discs of any kind of music, DVDS and software programs for several months now.  The main problem seems to be with an inability to properly install the driver for the cd drive.

  When running "find and solve the problems" of section "Troubleshooting" in the Control Panel, I get an error message that says that there is a problem with the driver for the cd drive.  Whenever I try to install the driver, he is not able to do so and contact the manufacturer of your computer.  I also tried to download all the updates and I get essentially the same message.

  Also, here's all that I've done so far.  I followed all these steps, but the last two listed in the help or support of the site.  Here is the link I used:

  http://support.HP.com/us-en/document/c01897812

  I couldn't do a restore of the system in step 7, because the last date that I could find to a restore point has been today (or yesterday).  In addition, I couldn't do step 8.

  Any help would be greatly appreciated.

  Thank you

  Hello:

  See if ongoing automated microsoft fix tool for you works.

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/

  If AutoCorrect does not work, try the manual fix in section "Let Me difficulty it myself, ' on the link below.

  Right to the title of this topic is a "click here to view the solution."

  http://support.Microsoft.com/kb/982116