HP pavilion dv6 3236nr wil not not allow me to access my home network.

Similar Questions

• HP Pavilion DV6 6120us does not completely close

  My HP Pavilion DV6 6120us crashes during stop. Windows looks like it goes through the process of closing and the screen goes black but the border mouse pad remains on and wifi (f12) button goes orange. The only way to close it completely is to hold the power for a few seconds. Once I start it again, it said that Windows was not shut down properly. After a few days ago, now the laptop battery is not detected.

  I went into the BIOS and run the embedded memory test and hard drive, but both passed. I haven't done a reinstall of Windows, but the battery problem now I think it could be the motherboard, but I hope that it is something else, because it is out of warranty. I am running Windows 7 family SP1 64-bit edition.

  I've seen a few posts on this forum with the same symptoms, but it never seems to be solutions. Any help is appreciated.

  Hello @Rangor and @dottorepcdotcom,.

  I'm sorry to hear that you both have the same problem with your HP Pavilion dv6-6120us Entertainment Notebook PC computer to not stop correctly. I have things that you can try before you commit a material error.

  First of all, I would like to you follow the steps in the HP Support document: performing a hard reset or forced to reset.

  Secondly, I would like to try a stop with ALL USB devices disconnected from your computer.

  Thirdly, I would like to allow you to start your computer in Mode safe. You can do so by following the steps in the HP Support document: Windows 7 Safe Mode and once it is completely started to stop him. If it stops correctly we have driver problem and I would like you to use the HP support document: use of the Recovery Manager to restore the software and drivers (Windows 7) to load the original drivers supplied with your computer. Make sure that you start with the Chipset drivers and install ALL the drivers available. DO NOT RUN UPDATES! Now try to shut down your computer. If it still has the issue make sure that you now follow the steps in the HP Support document: using HP Support Assistant (Windows 7) and make sure that ALL the HP and Windows updates are done.

  Back, I would like you press F10 at startup and enter your BIOS. Once you are in the BIOS, press F9, which will save and quit with the default values.

  Fifth, I want to make sure that your BIOS is up to date. You can check your update of the BIOS on the HP Pavilion dv6-6120us Entertainment Notebook PC Drivers page.

  I hope these suggestions help to solve this problem for you. Thanks for posting on the HP Forums. Have a great day!

• HP Pavilion dv6-3103sa: HP Pavilion dv6-3103sa does not then illuminate that plugged

  Hi - my HP Pavilion dv6-3103sa has recently developed a fault.

  It lights up with the power cable connected to it.  So that the laptop starts I have to first remove the power cable.

  Similarly, before you turn off the laptop, I need to unplug the power cable.

  If I leave it plugged in and turn off the machine, I can't start at all. The solution is to remove the power cable and the battery, then replace the battery only and then turn on the machine.

  I also noticed that with the removed battery and the power cable is connected, the laptop does not start again.

  Watching the light next to the power cord plug when plugged in the cable it quickly flashes of white, to orange, then back - tell me no power isn't learning laptop in this State.

  I also tried a different power supply with the same intensity from a mobile phone of similar work with the same results.

  Please notify.

  @ScatchyMonkey,

  Hello and thanks for the display on the HP support forums.  The problem you are having is with the motherboard.  There is a part that regulates the power and allows the system to know if it is connected or not connected and if it failed, you will need to have it sent repair.  Here is the link that will help you communicate with the correct service.

  Contact HP support.

  Thanks again for posting and have a great day.

• XJ437PA #ACJ: Pavilion DV6 - Audio does not

  Hello

  The audio has stopped working in my laptop since these days. It started with the audio does not not intermittently, but he has completely stopped working. I shared my PC specs below:

  Product name: HP Pavilion dv6 Notebook PC
  Product number: XJ437PA #ACJ

  Processor name: Intel (r) Core i3 CPU M 370 @ 2.40 GHz (2 400 MHz)

  I went through this forum and tried a few things:

  (1) to reinstall the codec IDT high definition

  (2) using the file available in the Recovery Manager

  (3) using the MicrosoftFixit

  But the problem is not yet solved.

  Can you please provide some suggestions?

  Thank you

  David

  Hi David,

  I would suggest you try a slight variation on the first two methods.
  
  Download IDT Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp47001-47500/sp47393.exe
  
  One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.

  Right-click on the Audio display Intel entry and select uninstall - this time check the confirmation box to remove the driver and continue the uninstall.

  Then, right-click on the IDT device and select uninstall - for this entry, also check the box confirmation to remove the driver and uninstalling.

  Once completed, restart the laptop.

  When windows has reloaded, open your download folder, right click on IDT Installer and select "Run as Administrator" to launch the installation. Once done, restart the laptop.

  Any improvement?

  Best regards

  DP - K

• Pavilion dv6: laptop does not

  I was given a Hp pavilion Dv6 some time ago and I tried to run but I don't know what's wrong with him

  When I plug in the power ring lights and when I press the power button on the fan and other lights come on but the screen does not work. When I press Ctr alt delete it restarts and now the backlight of the screen lights up but nothing appears. When connected to an external monitor a cursor appears in the corner of the screen for a few seconds then disappears, I tried to put disc in there but I still nothing No bios or the empty start screen.

  Thanks in advance if you can help me!

• Pavilion dv6-6b19wm wifi not working not

  Hello, I recently did a factory reset on my computer because it was really slow and now my laptop is not connecting to my wifi. I even pressed the button wireless on my keyboard, but it still shows an orange light of signalling that it is switched off/disconnected. I also tried to connect through the LAN / Ethernet cable, but it still does not work. When I go to Device Manager and click on 'Network controller' it says in the status of the device: "the drivers for this device are not installed. (Code 28) - there is no driver selected for the item or a set of device information. What should I do to correct this beings I can't connect to the internet for this problem on my laptop.

  Here is some information on my computer:

  Product name: HP Pavilion dv6-6b19wm

  Product #: A1T65UA #ABA

  Reinstalling the software/drivers:

• HP Pavilion dv6-6160se: could not find PCI Simple Communications Controller

  Hello I just reinstall windows 7-64 bit and it has this damage that I can not find the suitable driver for.

  I can't find the PCI of Simple Communications controller on
  (HP Pavilion dv6-6160se) with this code:

  PCI\VEN_8086 & DEV_1C3A & SUBSYS_3388103C & REV_04
  PCI\VEN_8086 & DEV_1C3A & SUBSYS_3388103C
  PCI\VEN_8086 & DEV_1C3A & CC_078000
  PCI\VEN_8086 & DEV_1C3A & CC_0780

  Thank you is advanced.

  Hello

  First of all, make sure that you have installed the Chipset driver from the link below.

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55095.exe

  Once completed, restart the laptop.

  The hardware id you have posted is the driver of the IMEI on the following link.

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55100.exe

  Kind regards

  DP - K

• Pavilion dv6 Webcam does not?

  I have a Pavilion dv6-1030 ca laptop, and since a few weeks, I had trouble with my webcam. When I open the HP MediaSmart Webcam, I get the following error message: "no video device detected. Please connect a video device to your computer. If you are using a built-in camera, please make sure that it is turned on. "I have a built-in camera, and (usually) lights up when the webcam application opens. I am running Windows Vista with SP1 and tried many things to fix it, nothing helps. The webcam does not appear in the device, under imaging devices Manager, nor any of the Hubs USB root. So far I have tried:

  -Reinstalled the drivers of USB root hub

  -A tried to fix the solution in the BIOS (that another thread suggested)
  -A tried to use Recovery Manager to reinstall the driver (wasn't in the list)

  -The recovery disks created to solve the problem (it didn't)

  -Updated the MediaSmart Webcam software

  I'm at school right now, and I can't really afford to give my phone to obtain compensation for three weeks since I have exams coming. Any help would be appreciated! Thank you!

  Message edited by annabelle89 on 27/07/2009 20:30
  Message edited by annabelle89 on 27/07/2009 20:31

  Don't pay fees to repair overpriced... it happened to dv6 my boss, lift just the frame surrounding the top and sides.  You don't need a crowbar on the bottom of the frame.  Use your nails under the inside edge of the frame, they have adhesive tape double-sided, so it can be a little difficult to dislodge.  Lift slowly so that the band can separate on its own.  Don't force quickly or you could damage it.  Make sure you are not prying the metal frame silver of the LCD, only the black plastic frame.  There are hooks plastic that will make a click sound when you lift up the frame, it will need a strength, so don't be afraid if you hear the wink, he should be able to put it back together if you did it correctly, otherwise you will need to use some tape to tape the rear frame, better than paying $100 +... haha.  Once you have pryed on the top of the frame and have access to the webcam module, you should see the cable going into it from the bottom, push the cable into the webcam, then see if the problem is resolved, the cable most likely just came loose.  If that solved the problem, I suggest to use something you can remove, as hot glue to hold it together, just in case the webcam really needs to be replaced, you can melt the glue wide and swap out.

  If your microphone works very well and just the webcam does not work, then the problem is most likely a driver problem, or the webcam itself somehow has been damaged, which is highly unlikely.

• HP Pavilion dv6-6c57ea detects not wireless card

  HP Pavilion dv6-6c57ea

  Windows 7 64 bit

  No error message

  Uninstalled the wireless adapter

  I was getting problems that google chrome could not connect to the internet so I decided to uninstall my wireless adapter and then restart my laptop in the hopes that it will automatically reinstall the adapter and my chrome problem will be fixed, until I realized that he never reinstalled the adapter and I have stuff like my laptop restart and reinstall the drivers , but which did not help.

  Hey AttackOfZaq

  1. when I rebooted my laptop I had some sort of error from the BIOS.

  2. it still lists himself as controller of network in other devices.

  3 then network works perfectly.

  4. the work of the internet.

  I solved the problem by updating the drivers for the network controller because there were none installed for this according to windows.

• HP Pavilion dv6 - 6052ea: fan of hp Pavilion dv6-6052ea does not

  Hi, this is my first post so here.

  I have a HP pavilion dv6-6052ea LL050EA product number and the fan has stopped working so I need to replace it, but I'm

  not sure that one to buy.

  I have windows 7 64-bit with 2 GHz Intel Core i7-2630QM processor and graphics card AMD Radeon HD 6490 M (1 GB of DDR5 memory).

  If I read the information about the product and he understood (as much as I can) I think that I need the fan/radiator kit which is

  part number 641477-001, someone can confirm that this is the one I need and also someone could tell me if

  This includes the thermal material bre what I owe this to buy separately.

  Thanks in advance for your help.

  Hi Phil,

  This number is for portable computers running AMD processor. You must get the so-called 641477-001.

  I think you better return her you already received.

  Confirm the part number with the seller and then proceed with the purchase.

  Concerning

  Visruth

• HP Pavilion dv6 a1u58av: drivers Hp Pavilion dv6 a1u58av Can not find good Wifi

  Hey! I seem to have a problem.

  I just did a clean install of Windows 7 on my HP Pavilion dv6. In the BIOS it says it's an a1u58av. (dv6t 6 c 00?)

  I used this page to get all of my drivers:

  http://support.HP.com/us-en/drivers/selfservice/HP-Pavilion-DV6-entertainment-notebook-PC-series/521...

  All those I work except for the Wifi drivers. I downloaded the ralink those, and they do not seem to work. I get the windows error message that they do not seem to be installed correctly. After several attempts, research on Google and it recharges, I still can't connect to wifi, or even find task bar icon in my status bar. Realtek LAN drivers work for the ethernet, and this is what I currently use.

  Any help would be greatly appreciated, thank you!

  Hello

  It's a machine CTO, wireless card can be one of the following:

  

  Source: http://PartSurfer.HP.com/search.aspx?SearchText=A1U58AV 

  To find out which, you need the hardware id. Please use following instructions to get hardware id missing then return:

  http://www.WikiHow.com/find-hardware-ID

  Kind regards.

• HP Pavilion dv6 entertainment: Cortana not see internet wifi (in English and Italian)

  I'm Italian,

  I've recently updated to windows 7 to 10.

  I have some questions:

  (1) why Cortana not see my wifi connection? Ditto Microsoft Edge.
  But the connection goes because I am not here.

  (2) why can't I activate windows 10, after update to 10 windows 7home Premium.
  -----------------------------------------------------------
  IO sono italiano.

  Ho aggiornato al windows 7 10 recently.

  Ho delle request:

  (1) boom Cortana non vede internet outdo mia? Lo stesso vale per Microsoft Edge.
  The hotel will not sari since that.

  (2) perched non posso switch windows 10 dopo aggiornamento di windows 7 Home Premium al 10?

  Hi @alienogiocoso,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dv6 Notebook and questions with Cortana. Here is a link to solve problems with Cortana.

  I hope this helps.

  Thank you.

• Pavilion dv6-7029wm, do not boot after BIOS update

  Hello

  Here are the details of my laptop and the problem.

  Product name: Pavilion dv6-7029wm

  OS: Windows 7

  Error: Fail to start. Caps Lock flashing in 1-1/2 dry once continuous, red wifi light on. Power light and the battery light on, no flicker.

  Pre-grant changes: updated to the latest BIOS updates as well as 3 other updates; security etc.

  I've tried remove the battery, unplug adapter, start-up. It still does not work.

  Its only for 5 months I've had this laptop. Please help me.

  Hello again Sowmya_Harsha.

  Unfortunately there is nothing more I can do.  However, I've increased your case.  You should be contacted by a specialist soon.  They normally have with customers using the feature of private message on the forums.  If you don't know how to use the private message function, take a look at this thread. I wish you a great weekend!

• HP pavilion Dv6 laptop: does not start in normal mode, safe mode

  Hi all

  I have HP Pavilion DV6 laptop with windows 7 Home premium 64-bit OS. It was working fine up until two or three days.

  After that some software upgrades, it has stopped booting.   When I tried to start it in safe mode, it stops at disk.sys.

  I don't have win 7 OS CD or recovery CD.  So I downloaded the trail version of windows 7 SP1, I want to install this, but he is suspended the windows logo.  I Googled it has bitten, I loaded a linux kernel and access the hard disk.  I backed up all the files required by using this boot of linux.

  I don't know what to do now?  What is the problem with my system. When I ran the drive diagnostic. It was a failure. That means that I can't use this HARD drive?

  Any help is greatly appreciated.

  Concerning

  Stéphane

  Hi stephane,

  Well the error code certainly would indicate that the player began to fail, but just in case, you might try to wipe the entire hard drive first and then reinstalling the operating system as described below.

  Download and install Killdisk on the link below - (this application will write zeros to the entire disk).

  http://Software.LSoft.net/KillDiskSuiteFree-Setup.exe

  Download and install ImgBurn on the link below.

  http://download.CNET.com/ImgBurn/3000-2646_4-10847481.html

  Access the application of disc kill you have installed in all programs, open the main folder, then select Bootable Disk creators, then the BACK Bootable CD Creator that will burn the ISO on a blank CD bootable.

  During the following process do not worry about all warnings as your Windows 7 installation disk will reformat the HARD drive.

  Insert this CD into your PC which is unable to load the operating system properly. Close Notepad, and then start again to boot from the CD of Killdisk and follow the instructions on the screen to kill disk.

  A brief description of the process here is Killdisk.

  Use it to wipe the entire hard drive, Select (80 h) and press f10 (you will also need to type a confirmation and press enter) - ( This will make sure to include all of the partitions , and then start the process - this may take a few hours!).

  When the process is complete, remove the CD of Killdisk and try to reinstall Windows 7.

  If it still does not work, I think your only option is to replace the HARD drive.

  Kind regards

  DP - K

• HP Pavilion dv6 keyboard works not properly

  Hello

  I use a HP Pavilion dv6 laptop running Windows 7 for about a year and a half.  Recently (I can't say exactly when) I noticed that my keyboard does not work properly.  There is nothing huge, but sometimes I have to push a button twice before she will comply, or it will be delayed in its response.  Another thing is that I originally used to have to hold the function key and press the space bar at the same time turn off the light that surrounds the touchpad. Now, I just simply press the function key (not now) and, no matter how many other keys I press on in the meantime, the next time that I press the space bar, the light turns off.  It's both distracting and frustrating because I need to press the space bar to operate normally.

  My drivers are all up to date.  I tried to remove them and reinstall them. I changed a few settings in the Bios, and then reset the default settings, all to nothing does not.  I would appreciate any idea or you guys can offer me solutions.

  Thank you!

  Hi El Nacho,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP Pavilion dv6 and keyboard problems. Here is a link to uninstall the keyboard. Restart the computer after the uninstall, it must be reinstalled automatically.

  Have you tried to take a little air to the keyboard to see if maybe it's dust or debris which initially are intermittent use?

  Thank you.