HP Photosmart C8180 will not light

Hello

I have a HP PhotoSmart C8180.  I recently moved and the printer was working fine until I moved it, but once it was plugged in after the move, the printer lights not at all.  The move was only 1/2 mile so he simply sat nicely on a car for the car seat and has not been disturbed around.  I tried a second original HP power and it made no difference.

The power light comes on and the system powers the LightScribe disc but nothing else.  Making sure power is disconnected for hours even before plugging it back in does not give any different results.  I tried to press a variety of buttons while it turn to try to force a system reset any without change as well.

Any suggestions?

Thank you!

Keith

Thank you.  I had no time to answer back previously, but in fact, this has been resolved.  I think that what ended up finding it was the small watch battery figure on the map system inside the printer, leaving all the drains of power that remained in the chips, then put the whole thing back together again.  After turning on it always came not for a few minutes and then roar back to life again.

Thank you!

Keith

Tags: HP Printers

Similar Questions

  • Why my Photosmart C8180 can not see my Virgin super hub, when he sees all the other distant routers?

    I'm on Mac OS x 10.7.2. I have a blank superhub. My Photosmart C8180 will not detect the hub using the wireless Assistant, but sees other networks in the region. I tried setting that allows a fixed IP address in the range of the router. Still nothing.

    Pilots etc have been updated for Lion ffollowing as instructions on the HP site but still no luck. Can anyone help?

    Diagnostic summary reports: -.

    Radio on: PASS

    The radio work: PASS

    Cable not connected: PASS

    Network name (SSID), found; IN CASE OF FAILURE

    The six remaining diagnostic report does NOT RUN

    Record of the summary reports: -.

    Network name: NOT APPLICABLE

    Hardware address (MAC): {identified but not included here}

    IP address: NOT APPLICABLE

    Configuration source: NOT APPLICABLE

    Communication mode: INFRASTRUCTURE

    Authentication type: NOT APPLICABLE

    Encryption: NOT APPLICABLE

    The blue light above 802.11 g on the right face is on.

    The printer works properly when connected by USB, but not with the radio.

    Kind regards

    Michael

    Security mode is set to [AES] WPA2-PSK and SSID Broadcast is checked.

    ID of 5 GHz Wireless band setting

    I tried to change to auto WPA, but it has no effect. Still does not see my router.

    Printer is set up for sharing in the Mac system preferences

    Just found my own solution.

    Changed Wireless 2.4 GHz band and has appeared.

    Thank you for taking the time to answer anyway. One to save for the future, if someone else reports similar problems with blank superhub.

    Kind regards

    Mike

  • HP Photosmart d110a will not scan.

    HP Photosmart d110a will not scan.  The resettled drivers, checked, put off - tension, nothing works.  Using Windows 7.  Error message is ' try scan from computer or see the documentation.

    Hello smhbcd

    The current software and try to reinstall using the latest drivers from the website. The link below will take you to the page "Select your operating system". Do it and download the latest driver full features.

    Photosmart D110 software

  • HP Photosmart 3210 will not install on Windows 7 Pro 64 bit.

    HP Photosmart 3210 will not install on a brand new desktop running Windows 7 Pro 64 bit.  I downloaded the latest software, and when I run it, the installation window disappears shortly after it starts.  No error message.  I ran into several related issues lately.  I can't install a ScanJet 5590 on a new laptop running Windows 7 Pro 32-bit.  Said it ends, but nothing is installed.   Could the fact that there are other HP printers installed on these computers (network printers) installed using driver only before attempting to install the software cause problems?  I spent hours trying to solve these.

    OK, much better progress!

    If the software is always installed, tell him you'll connect later.

    Go to devices and printers, look for the printer here, make sure you that no documents waiting to print and delete the printer if it is there.

    Then go into Device Manager and remove all photosmart series 3200 drivers you find, you may need to click displays hidden on the view menu.

    Thirdly, go back to the devices and printers. Select another printer, as the writer XPS comes with Windows. Along the top, with adding a device, add a printer, print server, you will see properties. What to choose and go to the tab drivers. If you have the HP drivers in there you do not, select them and choose delete and "delete the driver only."

    Now restart and go to your Start menu and your HP folder. You must have installed the software, just no device driver, select "add a device" or "printer setup and software." Installation should complete without problem.

    One last thing, you must temporarily turn off firewall and antivirus installation, in which case he mistakingly tries to block the attempt to install.

    Good impression!

  • Acerc720 screen is still very low and will not light

    I have an Acerc720 that has been discontinued (student), and now the screen will not light up. I tried the suggestion of recommended powerwash here and also checked to see if the function keys have been activated (not an easy thing to do with the dark screen). Nothing helps so far.

    Any other suggestions?

    Hello

    Connector to cable/LCD CHEK the EDP as thos:

    1. Unscrew the screws of the bottom
    2. Drop the bottom
    3. Disconnect the battery from the motherboard
    4. Remove the LCD Panel
    5. The LCD connector is located in the Middle under the black ribbon. Check if it is correctly inserted.

    If this doesn't solve your problem, the LCD is faulty.

  • Photosmart 6525: will not print in black

    My photosmart 6525 will not print in black ink.  Clean the printheads 6 times. Cartridge replaced twice. Any suggestions?

    Hello

    Welcome to the Forums of HP Support! I see that you are having problems printing in black. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

    Try the following steps to see if it will solve the problem, HP Deskjet 6520, printers HP Photosmart 6520 - printer prints a blank Page or doesn't print in Blac...

    Here is a document to manually clean the contacts of the cartridge, "not compatible ink cartridge" or "specified ink cartridge needs to be replaced" views for HP Deskjet i...

    Do not take into account the title.

    Here is a document for the reset of the printer. Ignore the title, HP printers - solve the 'problem with printhead,' "The printer failed," 'Ink system failure', or ' 0 x. / c0 > »

    Please let me know the result and if there is anything else I can help you. Thank you.

  • Curve Smartphones blackBerry 8330 will not light

    Hello I had my Blackberry Curve 8330 on my Verizon plan for 2 months and the trackball fell and the phone now will not light. No, he is not dead. I loaded hours (the light turns while loading) and yet the phone still turn. Please help and thank you

    Leave the appliance to charge on a wall charger, then, still connected to the cable, remove the battery from the camera for a minute and reinsert. If it starts - let - the charges to 100% (check the Options > status for the percentage). If it is not restart on the first attempt, leave several hours. I had a charge for two days before, she came back to life after extreme exhaustion of the battery. Every 3-4 hours with the device plugged into the charger, you can remove and replace the battery to see if it restarts.

  • Photosmart C7280 will not scan

    I am running Windows 7, I just replaced a photosmart c6180 with a Photosmart C7280.  The C7280 will not scan.

    When I use the Solution center, the analysis shows a black with no document screen as someone forgot to turn on the light.

    I tried printing and scanning utility, he said I was missing a update on the Solutions Center.  I loaded it and I still have

    have the same problem.  The printing and scanning utility now works without error throughout.  Until I loaded the C7280

    software I removed all software C6180.  I did some research and found that I should use a scrubber to get rid of all the

    the previous software.   I found a list of what it takes in hp support forum 1380995 and followed to the letter.

    I still have the problem. I'm on a 32-bit computer.

    Thanks for any help.

    I guess that's it.  I want to thank you for all your help in this matter and stick with me.

    Thanks again.

  • New Photosmart 5520 will not print in black

    I have a new HP Photosmart 5520 printer all-in-one.  Black ink ran out so I replaced it with a previously used ink cartridge which is of the same type # 564 but a XL version.  This cartridge has been barely used.  Now, I just can't get anything to print in black.  It will print in color, but not black.  I tried to turn off the printer.  I put the cartridge in my printer and it worked fine.  What should I do?

    edgarlogcabin wrote:

    my printer hp 5520 will not print black

    The in the here document troubleshooting steps may help resolve problems with black not not printing on your Photosmart 5520.  Especially make sure to check the events as on the Six Solution.

  • Photosmart 5510 - will not print in black ink

    PRINTER HAS FAILED - CLOSING OF THE FORUM.

    {title of the origninal thread restored in order to make the more searchable topic}

    This is a simple fast recommendation I would try.

    Remove the cartridges from the printer. Once they are there, try a hard reset of the printer. Once the printer turns and asks the cartridges, then go ahead and implement what their return.

    Follow these steps to perform a hard reset on the printer.

    1. press the power button to turn on the product.

    2. with the product, unplug the power cord from the back of the product.

    3. disconnect the power cord from the wall outlet.

    4. wait at least 15 seconds.

    5. plug the power cord into the wall jack.

    6. reconnect the power cord to the back of the product.

    7. If the product does not light by itself, press the power button to turn it on.

    Try and let me know if it helps. If not, there is probably a more serious hardware with the printer problem. Especially if you have experienced already troubleshooting guides. There is still one thing, we can try, which requires a certain type of reset of the printer, but I will have private message you the steps to do this.

    If I was helpful, or if you want to say thanks you can click the White Star under my name to give me congratulations.  I really appreciate it!

    Good luck

    Kyle

  • Satellite L500-19 x - is automatically disabled and will not light

    Hello
    I was in the middle of my review using my laptop stated above, when it is just off, it was plugged, it wasn't the battery for this purpose. But it does not ignite again, I disconnected from the grid and normally when it is running on AC it will acknowledge this with a light, but doesn't work. Also when I push the power button or network it will not turn on.

    I bought the laptop in December 2009 and it happened the first week I had, but the computer was warm to the touch and more heated theresfore, but this time the laptop wasn't hot yet and that he had been on 1/2 hour. I decided to leave a few hours and when I tried again to the base of the laptop is cold to the touch, but it not always light.

    I was wondering if someone could help me understand what's wrong with it

    Thank you very much.

    Hello

    There's LEDs, while the AC adapter is plugged?
    If this isn't the case, then there could be something wrong with the AC adapter or the mother for laptop.
    But if you are sure that the adapter is 100% ok, then it might be a problem with the laptop.

    It is difficult to say what might be wrong here as mentioned; If the LEDs shine t n, then mobo could be affected if the power LED to, then you should check the bars of memory in some cases the laptop would be light not because of faulty memory so it s certainly worth a check

  • Photosmart 5520: Will not print in black ink

    I did an interview on the print head, but it will not print in black. All other colors are fine and the ink is full so please tell us what can I do?

    Hey @Hughes23,

    Welcome to the Forums of HP Support!

    I understand that you have some problems with printing in black of your Apple devices to your 5520 Photosmart e-all-in-one printer. I can help you with that.

    This document describes How to solve print quality problems with your printer. If you access all the steps to ask you to replace the cartridge or the printer service, instead contact the HP support directly. You can do this by clicking on this link and fill out the form below to discuss the options based on your warranty.

    If this allows you to print, please let me know by clicking on accept Solution below my post. Also, I would like to know if you have any other questions. If not, have a great week!

  • HP Photosmart C4780: HP photosmart C4780 will not scan to my computer

    I plugged in just this HP all-in-one to my computer.  It does not analyze to my computer.  It will scan on an SD card without problem.  What can I do to make the scan to my computer?

    Hi @Lisa213,

    Thank you for joining the HP Forums!

    I read your post on how your HP Photosmart c4780 printer will not scan on your computer. I'm happy to help you!

    A few questions for you:

    • How is the printer connected, wireless, Ethernet or USB?

    • What is the operating system you use, Windows or Mac? What version?

    In the meantime, maybe one of these guides will help:

    For future reference, hereis the user guide for the your printer.

    If it helps, please consider clicking on "accept as a solution." And, please click the thumbs up icon. The two icons are below this post.

    Hope this helps, and hope to hear from you soon!

  • PHOTOSMART 5520 WILL NOT PRINT BLACK

    I just replaced the cartridges for my PHOTOSMART 5520.

    After that, color printing has no black color.

    All HP cartridges are not new.

    It's very frustrating.

    for some unknown reason, this problem is gone when I tried printing 2 weeks later.

    To summarize:

    I'm in the United States.

    I replaced the 4 cartridges again purchased at HP online.

    After that, the black will not print if I choose to print in color.

    But if I print in "black and white only", black is in fact works very well.

    I tried everything suggested in the web forum such as cleaning, alignment, prower AC cycle,... etc. He has not fixed the problem.

    I stop using the printer for 2 weeks. But yesterday, I try agin, then the problem is gone.

    I don't know what to say. Thanks to HP for assistance.

    Overall, the servie is nice - just called him several times.

  • HP photosmart 5515 will not print black.

    HP photosmart 5515 do print not black, but is printed colors (cyan blue yellow). Printer shows full inks on all colors.

    There is a document with steps to help resolve a print quality problem where black ink will not print Photosmart 5515. This document can be found here.

    I hope this helps.

Maybe you are looking for

  • Satellite A100-151 (PSAA9E-01Z01DGR) - new compatible mainboard

    Hello I come from Germany and my English is bad, but I try! The motherboard in my Toshiba Satellite A100-151(SPS: V000068170) is corrupted. Now, I can buy one with SPS: 000068270. Now my question: can I use this card as a substitute for my old?

  • Data before release for NOR-6133 trigger material and acquisition continue?

    I use the pxi of NOR-6133 can acquire data on 7 channels continuously with ai0 as the trigger without problems. The acquisition is triggered. What I have to do is collect a finite amount of data before triggering immediately until the trigger is dete

  • New installation of Windows 8

    HP ENVY 17-j070ca notebook PC I want to install an ssd on my laptop, but met with many problems. To begin with, as a first step, he couldn't see the ssd. A ran diagnostics, its ok. Tried to reimage from an image I made of Windows backup on a WD MyBoo

  • Can I get my free upgrade product key of windows 10?

    I upgraded my pc Windows 10 of media creation tool Please Microsoft give my product key, you can also send me an email. Please please please answer me.

  • Add 2 GB of Ram in TP X 201

    Hello I'll buy a TP X 201 with 2 GB of Ram... one question: is there another location to add another 2 GB of Ram and thus reached a total of 4 GB of Ram? Thanks a lot to all Nice day Dany