HP2840 which has just started to squeek terribly after changing the drum.

Similar Questions

• Office stuck in a loop of starting Windows XP restart after changing the map of memory of RAM DDR

  I added that a card of memory DRAM DDR to my CPU ENPower and immediately after my monitor has not received a signal. Then, after reading several articles, I cleaned the CMOS battery, and although he got the monitor works he has also prevented my system to boot with the Windows XP operating system. I've accessed the CMOS utility to change the date/time, nothing helps I still can't get in Windows XP and the user login screen. Now, the system passes through 1 and 2 screens that are part of the commissioning, then lands on the Safe Mode Options screen by which he gets "stuck" not allowing me to select the data options, then it will auto restart every 30 seconds.

  The screen message reads:

  "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this. If your computer stopped responding, restarted unexpectedly or has been automatically closed down to protect your files or folders, select last good known Configuration to return to the most recent settings that worked. If a previos startup attempt was interrupted due to a power failure or because the power or Reset button was pressed, or if you are not sure what caused the problem, choose Start Windows normally. »

  Safe mode

  Safe mode with networking

  Safe mode with command prompt

  Last good known Configuration

  Start Windows normally

  All the these appear on the same screen, but I have no opportunity to select one of them during this mode my pc in.

  What should I do? I need to access the BIOS utility to change the settings of the RAM, or is there something else that I forgot who will be able to get my pc to the top and running properly again?

  Thanks for your advice in advance!

  Remove the memory module that you added.  If the computer can be started without him, then the module is defective or is not compatible with your computer.

• Trial has just started... There is no button text only a text on a path tool... How to make a text box?

  Trial has just started... There is no button text only a text on a path tool... How to make a text box?

  The text button is under the text on a path button. Click and hold and it should reveal the buttons.

• 64 bit sytem with vista home premium which has been randomly locking up and freezing. The error is event 6008.

  I have an ACER aspire x 3200 64 bit sytem with vista home premium which has been randomly locking up and freezing. The only mistakes were event 6008 with a description of the stop system prior to (time) on (date) was not planned.
  When these errors originally occurred, I returned the system to acer and they installed a new hard drive. After updating the vista system blockages continue 30 times over a period of 3 months. Acer sent me a new disk image on 3 disks that I have installed and updated on 11 October. There is no blocking until the 10/27, 10/28, and for the 3rd time today.
  The closed unexpected gives a blue screen if I use the locking system to the top. I have to hold the power to restart when the system crashes.
  Can someone help me solve this problem?

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.  But I guess it's too late for this for so long that there are probably no so old restore points.

  If the system restore does not work, do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not work, try to start in safe mode (repeatedly hit F8 key so that the start and go in safe mode with networking).  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator.

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well he comes complete with no corruption, it could not repair (if it has these post of corruption here or try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228.

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If this does not work, then please post repetitive errors in Event Viewer on the stop (Start / Control Panel / administrative tools / Event Viewer).  Here's how to use Event Viewer: http://www.bleepingcomputer.com/forums/topic40108.html.  From what I understand, there is none of the events (which surprises me because a freeze should certainly generate an error event).

  If this does not work, you will need to do a repair/system upgrade using the Windows Vista Installation disc authentic (you own or that you can borrow from someone).  Here is the procedure: http://www.vistax64.com/tutorials/88236-repair-install-vista.html as well as the upgrade from an earlier version of the Windows section of the following: http://support.microsoft.com/kb/918884.  Although this will not affect your data, settings or programs, you should always back up your data before you start just be on the safe side. If other procedures do not work, it is almost certain to work (but you NEED a disc).  You can have a lot of updates to re - install (including all you need to remove service packs).  If the version on system with SP1 or SP2 preinstalled cane and the disc is an earlier version, then you will need to do a slipstream drive as follows: http://www.vistax64.com/tutorials/151606-vista-sp1-slipstream-installation-dvd.html.

  I hope one of these procedures can solve your problem.  If this isn't the case, after return and we will try something else.  Return message anyway so we know how it turns out.

  Good luck!

  Lorien - a - MCSE/MCSA/network + / A +.

• How can I design square wave which has a positive and negative values equal to the other and separated from each other by controlled time or distance

  How can I design square wave which has a positive and negative values equal to the other and separated from each other by controlled time or distance, as indicated in the figure below. and enter this signal in a data acquisition.

  

  At the time wherever you go for the beautiful diadram, you could have done the vi

  Your DAQ would like a waveform (table of values and dt ak 1/sampling rate)

  If you set the sampling rate you know the length of the array, create a matrix of zeros and set the values of the two amplitudes...

  Because I don't want to connect other duties here are some photos

  And it does have a few drawbacks leaves to be desired in my solution, just think... rounding errors and what might happen if the tables are becoming more...

  

• After changing the MagSafe adapter, macbook pro takes too long to start the video

  After changing the map of 85 W MagSafe, time to start the computer has become excessive (2 minutes). The screen lights up immediately, but the video appears after 2 Min.

  Once started, the performance of the computer are OK.

  This anomaly occurs after the change of the adapter, it's never happened before.

  Try a SMC reset:

  https://support.Apple.com/en-us/HT201295

  Ciao.

• My hotmail account has certainly was hacked and used to change the DNS settings on a vauable domain name registration.

  My hotmail account has certainly was hacked and used to change the DNS settings on a vauable domain name registration. Indeed, they stole the domain name, which used my hotmail account as account checking the change of domain name registration. It is a police matter. How can I get the security of Hotmail team to freeze the mail in the account and then return the account for me? I am the owner of long-standing account, since 1995. What should I do to prove that I am the rightful owner of the account?

  How can I contact Hotmail security ASAP?

  Hi JoePiecora,

  Thanks for posting your question in the Microsoft answers Forum. For any question on Hotmail, please visit the following link:

  http://windowslivehelp.com/forums.aspx?ProductID=1

• I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device. is it possible to reset to original settings?

  I hope someone can help me. I changed a few settings in the BIOS Setup, and now I have just a black screen. I changed the main boot to the DVD player device.  is it possible to reset to original settings?
  I am running Windows XP

  clint341,
  Thanks for posting on the Microsoft Answers forum.  We cannot guide you more precisely by changing the BIOS settings that the BIOS settings are specific to your motherboard.  However, most (if not all) parameters of the BIOS have an option to restore the default BIOS (sometimes called "default opitimized").  It may be an option in the menu that you highlight, then press enter or it can be assigned to an F key and States at the bottom of the screen, press F? for the default settings.  I hope this helps.  If you are still not able to reset, check with the manufacturer of PC for more information about the BIOS. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems Windows has just started.

  I was currently using vista windows on a computer hp laptop. He began to spoil with various problems of internet connection and not pick up on the drivers. I was told to use System Mechanic, which lead to all my files are completely erased. I don't have the disc to re-download, nor do I have the recovery disks. I do not seem to have any files left on this computer, except for the possibility to enter commands, which I'm not sure will work out well. If anyone has an idea on what to do, let me know would be a great help.

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You can also make recovery disk/s since the Partition of recovery in case of hard drive failure or System Crash, when you are in service again...

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• Weird question has just started - changes in my .cpp file is not used?

  I have a strange problem with my application. I have a working application that I built and submitted for review. I just make some changes and add a feature, but I find that when I change my (as simple as changing the debug messages) .cpp file the application that is deployed on the Simulator is mirror not them. It's just stuck. It works great even after that I have comment lines which should break/change the application.

  Anyone know why/how this could happen? It worked very well there's just before exporting a release build for the presentation of a few days.

  Delete the app in the Simulator? Clean and rebuild the project from scratch?

• Skype has just started crashing on multiple clients

  Skype uses every day for several years. Today, at random, it crashed. When the computer reboots, it repeatedly crashes within seconds.

  version: 7.5.85.101

  What I tried:

  • Deleted %appdata%\Skype and % of the appdata%\local\temp\skype\dbtemp. Same result.
  • Compact view. Same result.
  • Other computers. Same result. One is win7 other win8.1. Different versions of Skype.
  • Android phone, where he worked earlier today also. Same result.
  • I've never had 'citrix Receiver"installed.

  Event Viewer:

  Name of the failing application: Skype.exe, version: 7.5.85.101, time stamp: 0x555498e4
  
  Name of the failed module: Skype.exe, version: 7.5.85.101, time stamp: 0x555498e4
  
  Exception code: 0xc0000005
  
  Offset: 0x0022b3ac
  
  ID of the process failed: 0x70a0
  
  Start time of application vulnerabilities: 0x01d09d89fbc34d70
  
  The failing application path: C:\Program Files (x86)\Skype\Phone\Skype.exe
  
  Path of the failing module: C:\Program Files (x86)\Skype\Phone\Skype.exe
  
  Report ID: 4285c8a7-097d-11e5-92a7-8674f3e53184

  Why is he referring to phone on a PC?

  Signature of the problem:
  
    Problem event name:	APPCRASH
  
    Application name:	Skype.exe
  
    Application version:	7.5.0.101
  
    Application timestamp:	555498c 4
  
    Fault Module name:	Skype.exe
  
    Fault Module version:	7.5.0.101
  
    Fault Module Timestamp:	555498c 4
  
    Exception code:	c0000005
  
    Exception offset:	0022b3ac
  
    OS version:	6.1.7601.2.1.0.256.1
  
    Locale ID:	1033
  
    Additional information 1:	0a9e
  
    More information 2:	0a9e372d3b4ad19135b953a78882e789
  
    Additional information 3:	0a9e
  
    Additional information 4:	0a9e372d3b4ad19135b953a78882e789

  Cyph3r wrote:
  

  There are several temporary solutions to this problem:

  • Customer between version 7.0 - 7.1.0.105 works for me. It doesn't have this problem.
  • Ask the person who wrote the offending string to remove.
  • Use web client.
  • Date of the computer forward 1 month, let the cat and position it back.

  No 'Abracadabra' is no longer necessary:

  http://community.Skype.com/T5/Windows-desktop-client/Skype-fix-for-crashes-caused-by-bad-URL/TD-p/39...

• iPad Pro 12.9 "sound button.  Where is he? Today just started using and should have disabled the sound.

  Where is the button main sound on iPad Pro 12.9 "? Just started using it today and should have disabled the sound by mistake and now I can't find where to turn it on.  All sounds are on in the settings section.

  The volume of the up/down buttons are on the right side of the iPad.

  

  http://help.Apple.com/iPad/9/

• My office has just done a repair XP after a hardware change and now all user accounts have disappeared and he asks the administrator password when connecting!

  We have a unique system of Windows XP that run the software of engineering for certain calculations. All other systems running Windows 7, but what a XP system because it's the only thing that our calculations software runs on.

  CPU of the XP computer died on us and we had to replace the card mother and CPU. After the change of equipment, following Microsoft's OWN guide on the running an XP repair, we ran the system repair and got all the way to the login screen (no blue screen not as before repair). However, none of the accounts are there and he asks an administrators password. The system has NEVER had a password to our knowledge, it was built in the House, and all simply by clicking on the Administrative login asks for a password.

  What can we do? We needed this fix before today and wait for the repair of the system to do. Is it possible to enter the system to run the software? We tried the SafeMode (all forms) and they all will ask a password after Windows loading.

  It's so frustrating.

  (PS I have been building computers for nearly 15 years and have never had this happen)

  Thanks for the quick response. I looked into the system with a "start-up" program All original profiles seem to still be there. I don't know how to make them appear well. Can you direct me or tell me, how to make profiles see the place?

  The biggest problem, outdoors is not be able to sign more, is that the engineering calculation software is locked to this PC. It can be installed anywhere else without having to pay for a VERY new (I think that thousands of dollars) expensive key or a new version of the software.

  :(

  Yes, it's a problem.
  I believe you can use a UBCD4Win CD or Hiren Boot CD to locate and right click on the files you want to change. And then, if you properly in your repair facility, you change the attributes after you're done.
  Some guides are better than others. And here's one that I like:
  http://www.windowsxpprofessional.WindowsReinstall.com/indexrepairguides.htm
  If necessary, hire a PC Tech. It's much cheaper than buying a license that is thousands of dollars!

• A friend has two email addresses and want to change the default.

  A friend has an e-mail address main iCloud on his iPad, but does not know the password. We were able to remedy this and would like to change the e-mail addresses of the main one at the secondary level, which will make the default secondary image and the other main. In other words share the default email address now to make the secondary image by default, but always use the Mail app. The secondary address is Heaven who use Yahoo, so I use the drop-down list that appears in the settings and shows Outlook, Yahoo, etc, and select Yahoo, which Sky use themselves.

  She is an old lady who received his iPad by one of his own earlier, but which had not been deleted and no matter what, the settings are between the Member of the family. This lady is getting used to the use of Mail so prefer to stick with it, otherwise it will be the site of the sky and relearn how to Sky/Yahoo. I suggested to contact this member of the family, but I was told not to remember the password.

  I thought the reset of the iPad to remove anything to do with iCloud, but that has not worked. We went through iTunes and put his email address of sky (high school) there, he took, but that has not changed anything either. We managed to change its ID Apple logging in details to the new email address and password, then thought that the rest would be child's play, but no.

  Am I read and try to redo too to make the sky main e-mail address and a default? should I just use the menu drop down and select Yahoo?

  She doesn't have a clue on how to do these things, because it is very well a learner, this is why I am trying to help and think all this happened not knowing the password Apple ID.

  You are confusing two different issues. To change the default email in Mail and also talk with iCloud? While she may be the same as his Apple ID email address, the Apple ID itself does not affect the Mail application.

  Make Yahoo default email address and use iCloud are two totally different issues.

  So to answer the question of the Yahoo email to make the default account, you must ensure that it has been added to the iPad.

  Go to settings > Mail, Contacts, calendars > add account (unless the account is already here)

  Then scroll down on the same page and look for default account, type the following and change to any email address you want by default

  You can also delete unwanted emails in this same settings pane accounts by typing the address of unwanted e-mail and stitching remove account, or disconnection, if it's an iCloud account.

  If you did in fact change to iCloud account, the changes may not take effect until you log out, then back to the iCloud account.

  Hope this helps

• XP pro do not start after changing the Boot.ini file

  The problem is that my C: partition Windows 7
  D: has XP Pro

  These should be considered right resp. partitions 1 and 2?

  I wanted to first XP pro to start the default partition.

  A few days ago, I made a change to the boot.ini file. But since XP Pro was not starting at all.

  I tried XP Pro to start first that the default partition.

  Given that XP Pro and my D: drive have not been starting, I consulted the boot.ini file in C:, Windows 7 partition and I changed the order (i.e. partition No.) in the boot.ini file and saved it to the required location, i.e. D:/WINDOWS/pss.
  through my drive C: of work, i.e. the partition of Windows 7, but it still does not work because apparently even though I save here, the actual values and the paths of the partition are not actually be changed on the system. I confirmed this by going into the CMD shell switching to D: and by running the command D: > bootcfg.
  Apparently any values I save in the boot.ini file that I save as a text file or "All files" in D:/WINDOWS/pss/it does not actually change in the system because whenever I run the command bootfg values are remaining still and not able to be changed, because apparently it is not saved in XP Pro and the D : partition. No matter what I do and what I put in the boot.ini file to access the values through the windows 7 partition, the values that bootcfg returns me are always the same and he refuses to change the name of path or anything else. No matter what orders, I also put in bootcfg himself.

  These are the values that bootcfg gives me:
  default: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS

  Boot entries:
  Boot entry ID: 1
  Friendly name of operating system: MS Windows XP Professional
  Path: multi (0) disk (0) rdisk (0) partition (1) \WINDOWS
  The operating system load options: / noexecute = OPTIN/FASTDETECT/usepmtimer

  My XP Pro partition is simply not booting, and it of my main partition and has all my work. It is imperative that it starts.

  My Windows CD is also not start because apparently my DVD drive does not work properly, I had the anti malware threatfire (ThreatFire) installed on my XP D:Windows program disk but have uninstalled just in case it was blocking my changes to the system.

  On C:Win7, I put the default operating system option in the Advanced tab for Win7 and the D:XP Pro to XP Pro, when he was the starter and work. Now I can only access my files D:XP Pro Player C:Win7. But XP is not just start. What shd - I do? Thks.

  I don't have a very practical windows CD but my CD/DVD drive is not read and does not properly.

  Looks like your original post stated that your cd/dvd does not work.

  Respectfully, you will continue these hap hazard patches and your computer will not start at all. I'll try to help you once again. Please follow closely.

  Start your computer by loading Windows 7. Click HERE and download EasyBCD. Install the software in trial version. Once installation is complete open EasyBCD. You will see an interface like the image below. Click Add a new entry.

  

  A new screen appears as in the image below. Use the drop down menu to select Windows NT / 2 k/XP / 2 k 3 as described below. Type the name of the operating system in the box below. Of course, it will be Windows Xp (you can add the home or Pro to the name if you want). Make sure now that there is a check mark in the box "automatically detect the correct player. Once you have completed these steps click on 'add an entry '. That's all! You are finished. If all goes well, and if you have followed these steps carefully, there, now you have a system dual boot.

  

  You can now start working on your cd/dvd problem.