I do not have a dail-up, it is Verizion DSL. Problem is router does not connect to internet when I try ti sign in to MSN

Similar Questions

• Difficulty 'Not connected' Error Messages When you try to access Web Services

  If you are running on an error message on your printer stating that it is "not connected" when you try to access ePrint or your applications, but you know that it is connected to the internet, it probably just means that the printer does not connect to the server properly.

  Here's the first set of markets, I will try, as they seem to solve this problem deliver half the time.

  • The first thing I'd like to try in this situation is a reboot of the system.
  • First, unplug the power cord at the back of your router.
  • Then unplug the power either to the back of the printer or the wall without it first turn.
  • Wait about 30 seconds and reconnect the power cord to your router.
  • Wait about another 30 seconds and reconnect the printer. It should start back up automatically, but if it is not moving forward and press the power button.
  • Once everything is back running, try to access ePrint or your applications.

  If these steps do not work for you, the next thing would be to establish a static IP & DNS for the printer. Before doing this, you want to print a Network Setup page. It varies from a model, but usually found under settings wireless or in reports in the Setup menu. After that you have this page, follow these steps.

  Before we begin, we need a network with your current connection settings configuration page. To do this, press the button on the front of your printer wireless and press 'Print Info' or 'print the State. " This example displays on a page of configuration of the network, which provides information on what we have to finish the next few steps.

  • After that you have, we will need to access the built-in Web server (EWS) printers. You can do this by entering the IP address of printers (from the Network Setup page) browser press and the address bar type.
  • Once there, press the 'Network' tab at the top of the page. From there, you'll want to click on the button "IPv4", on the f-side of the page. It will be there for wireless and wired, so make sure you click the one for you, but you are connected. If you do not see "IPv4", you should see 'Networking', press and press "Network Address (IP).
  • Then, you click the small round button next to "Manual"IP address", and then fill in the IP address, subnet mask and default gateway using the information available on the network configuration page.
  • For the primary or the preferred DNS server, you will want to enter 8.8.8.8.
  • For secondary school or another DNS server, you will want to write 8.8.4.4.
  • Click on apply and when the message appears saying that the changes have been applied, press 'OK '.
  • Press the power button on your printer, wait that it completely power off and press it again to power it on.
  • After doing this, go ahead and try to activate ePrint again.

  These measures should fix this for you. If they don't, then something else can cause this problem for you. Reply in this thread if these steps do not work, and I'll see if I can help figure you out what might be causing the problem.

• have Netgear WN3000RP but can not connect to internet

  have the netgear wn3000rp Wireless extender hooked and on computer, but it wount connect to internet I can do

  HNO, it only fixing what can be done then?

  smlunatick is correct - you must have a modem/router wireless separated in addition to your wireless extension. Please see details here how it should be setup:

  http://www.netgear.nl/home/products/wireless-range-extenders/WN3000RP.aspx .

  You have such modem/wireless router? Please explain how you set up your network in what concerns your DSL access point (or equivalent), your PC, your wireless modem/router and your wireless extension.

  What happens when you try to connect to the internet? Please give error messages in its entirety.

  We need Details to help you better.

• iPad will not connect to internet

  Hello

  Recently I replaced my router wireless with an old faithful that d-Link DSL - 502T cable modem as I have now 2 extreme airport to handle a Wi - Fi. I have now a much faster internet access on my Macbook Pro, but my iPad 2 now will not connect to internet.

  Airport utility on the iPad shows that the internet is disconnected, but I don't know how to solve this problem.

  The two airports are configured in Bridge mode. Help someone?

  If you have LAN - 502T running as the main router.

  Bridge the airport should simply pass the DHCP via the Dlink but sometimes it's a failure.

  The two AE connected directly to the modem or the other?

  I would recommend the static method of intellectual property.

  https://discussions.Apple.com/message/25135547?ac_cid=tw123456#

  In this method, you must first AE plugged directly to the Dlink and the second AE connected in the first and bridge... it will dhcp to EI and is often a better configuration with Apple gear. Worth a try.
  

• Firefox is not connect to internet unless the reboot

  So, recently, I had a problem with Firefox does not connect to internet unless I quit and reopen the app.
  It happens like this:
  -J' open Firefox and it works;
  -I lose the internet connection (for example, I turn off my wifi, or my laptop goes to sleep);
  -J' I reconnect to the internet.
  -Open Firefox browser will not connect to what it is and continues to load when I click a link
  -J' I need exit Firefox and restart it before starting work again.

  It doesn't go to my other browsers (Safari, Chrome), once I have reconnect to the internet open browser will just continue to work without needing to be restarted.

  Is not a big deal, but it's a bit annoying and I would like to know if there is anything I can do about it.

  This is set for your network preferences in everything: preferences #advanced

  • Advanced panel - accessibility, navigation, network, updates, and other advanced settings in Firefox
  • Cannot find server - troubleshooting

• Equium L40 is not connecting to internet

  I have an Equium L40 it does not connect to internet with wifi or the head of the ubs.

  The laptop comes up:
  Internet Explorer has stopped working
  A problem caused the blocking of the program works correctly.

  It says it is connected to my wifi bt hub and has a signal strong.
  Why it will not connect either cable or WiFi?

  Any ideas.

  Steven

  Hello Steven

  It is not easy to provide a response based on the description of your problem.
  If you use connection WLAN make sure wireless network adapter is installed, enabled and configured correctly.

  USB cable? What type of USB cable do you use?

• iPhone 5s does not connect to internet unless its connected to wifi

  I have a 5 s IPhone it does not connect to internet unless I'm at home connected to wifi. I can not send imessages or browse the web what should I do?

  You did that mobile data is turned on in the settings/phone/cell data?

  Also, make sure that the apps you want to use for the cell data are enabled in the list below these settings.

• iPhone and iPad does not connect to internet

  Hello

  Since yesterday, I was unable to connect to internet via wifi on my iPad and iPhone.  They show the power of the full signal and says I'm connected, but won't load Web pages or refresh applications.  When I disable wifi on my phone everything works fine on the LTE, but I don't want to use my data.

  I think it must be something with the update iOS because:

  -J' completely rebooted our router and modem and it worked on my iPad for about 30 seconds (what makes a Web page) before it stopped working again.

  -My boyfriend did not the last update on the iPad or iPhone, and both connect on our wifi at home, while my iPad or iPhone will connect to the internet.

  -My iPhone also does not connect to the wifi in my work, even though I know it works as I am online on my computer work via wifi.

  I noticed something strange on my iPhone and iPad when I went to check the settings wifi yesterday - the VPN configuration is flashing/refreshing without touching me, even if I don't have everything set up VPN connections.  When I actually click on VPN, an error is displayed.  There may be something wrong with the VPN on the new update which blocks the wifi signal?

  
  

  I really appreciate your help!
  

  If you are able to connect your iPad and iPhone to your wireless router agreement but the iPad and iPhone will not connect to internet, it is unlikely to have anything to do with the version of iOS.

  Try this:

  Restart your router (unplug unit, wait ten seconds and then reconnect it).

  Wait for the router shows all lights normal and connected.

  Now, reboot your iPad or iPhone

• D7000 will not connect to internet after reinstalling

  Hello

  We moved our D7000 modem router from one room to the other and now it does not connect to internet at all. I spoke with our ISP and everything is fine on their end. I connected the modem and reset our ISP connection & the password, and the ISP did the same thing, without effect. The phone line has been tested, it's ok. I swapped the cables to make sure that they are not defective. I moved the modem to return to the old location, but now it does not work there either.

  WiFi seems to be ok and all our devices (phones, tablets, computer) recognize the wireless network and modem, but there is simply no internet connection. It is bizzarre! Nothing has changed, there is no new hardware, no updates or upgrades, the ISP is always the same, the only thing that differs is the location, in the same House.

  The lights on the router modem are as follows:

  Food - white

  Internet - amber

  DSL - off

  WiFi - white

  Any ideas what I could try to make it work again? Should I do a factory reset on it? This could be the cause? Move a modem do not stop working. We only had since November so it isn't old yet, and it has been working fine so far.

  Any help at all would be greatly appreciated!

  Päivi

  Hello

  It has been a while now, but I thought I would update this for anyone interested or affected by the same problem we did.

  After weeks of back and forth with the ISP and try and test anything and everything we could think, including the replacement of the D7000 in store warranty (not just once but), and nothing is helping, the ISP finally filed a foul for us and sent a CET. And what do we know? There was a flaw in the riding of Telstra which he had found, and which caused our internet connection fails. After that which has been set, we are online again. The line still falls here and there and the phone line is cute, but at least we are connected.

  And now I'm fighting with the ISP for refund during all these weeks we were disconnected while they refused to be a mistake for us and have someone out. Time for a new ISP, I think!

  Hope this helps someone else with the same problem there.

  Thank you

  Päivi

• Watch WiFi is connected but will not connect to internet

  I have an iPad 2 which, all of a sudden (in the Middle streaming), is more connected to the internet.  I rest the network settings, when this does not work, I have reset all settings, stopped and rebooted, all done basically.  It shows that its connected to my WiFi, but will not connect to internet.  All the other devices in my house work, then there must be a problem with the iPad.

  Reset the router: just pull the power for a few seconds and reconnect. No parameter to get lost.  Other devices operating with success is not serious. The router has probably received an invalid address for the iPad.

• New updates of Windows since 06/11/12 is originally Vista does not connect to Internet Explorer

  I have a desktop with Vista CAREB.  It has always worked well until about June 11, 2012.  Now it does not connect to Internet Explorer. It says it is connected to the internet and that has been verified by our server.  Tried everything and eventually restored it and no problem.  Then the next day, same thing and restored.  Next day same thing so I disabled all updates and no problem.  What new update windows made in the last few days which is the cause and what can I do?

  Thank you

  Hi Judy,.

  We cannot verify that Windows Update is causing the problem, I suggest to install the Windows updates one by one and make sure that Windows Update is causing the problem.

  Windows Update

• Upgrading from Windows XP to Windows Vista and now I can not find wifi or when I try to connect to the internet, I get an error, "a cable is not plugged on the network card.

  Wireless connections

  I upgraded my dell vostro laptop 1000 Windows xp to vista and now I can not find wifi or when I try to connect to the internet I get an error, "a cable is not plugged into the card network", "connection to the Local network. Everything worked fine until I upgraded. I noticed in my device manager, the driver for the system controller and core network are not installed. Could it be the problem? Is someone can you please help me understand this?

  Hello

  I noticed that you had created another similar to this question. Have you tried the steps suggested in this post?

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/how-do-i-put-WiFi-back-on-my-PC-after-upgrading-to/c9b90ec1-8393-4B57-b4af-2fbeb802af58

  You can also try the following methods and check if it helps.

  Method 1:

  Update a network adapter driver.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Troubleshoot network adapter problems.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

• Hi I'm trying to install windows 7 in my xp service pack 2... but I often get error code: 0 * 80070005... indicating that I was not connected to internet.but, in fact, I was connected to internet

  Hi I'm trying to install windows 7 in my xp service pack 2... but I often get error code: 0 * 80070005... indicating that I was not connected to internet.but, in fact I was connected to internet... pls sumone help me solve this problem!

  Boot from the Windows 7 DVD
  Click Install now
  Accept the license agreement
  When the option is displayed to select a type of installation, click (Custom advanced)

  Select the disk partition where you want to install Windows 7 click Next.

  You will receive the following warning:

  The partition you have selected may contain files from a previous Installation of Windows. If so, these files and folders will be moved to a folder named Windows.old. You will be able to access the information in Windows.old, but you will be able to use your previous version of Windows.

  (At all costs, do NOT click on anything in Format, deletion or Partition name.) So even do a custom installation, your personal files are still kept. Click OK

  The installation program will now begin installation. During installation, your computer will be restarted several times.

  Once the installation is complete, you can complete the Out of Box experience as the choice of your laptop, create a username, password, your time zone. You can then proceed to download the latest updates for Windows and reinstall your applications and drivers.

  You can then retrieve your personal files from the Windows.old folder and reinstall all of your applications and drivers.

  http://notebooks.com/2010/11/09/how-to-recover-documents-music-and-email-after-upgrading-with-the-Windows-old-folder/

• Windows 8 Upgrade Wizard does not connect to internet

  My internet connection is quiet well but windows 8 Upgrade Wizard keep saying we cannot connect now check your internet connection and try again.

  I have tried many time but it keep saying this message.

  Help, please

  Hello samia,.

  Thanks for posting your query on the Microsoft Community.

  According to the description, I understand that you can not connect to internet.

  I suggest you to refer to suggestions Moderator Forum Microsoft BillFill responded on 10 February 2013 and check if that helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/Windows-8-Assistant-error-cant-connect-right-now/17ec5088-28ca-4a03-8e29-0b9309bb9b9f

  Hope this information helps. Please let us know if you need any other help with Windows in the future. We will be happy to help you.

• How can I reinstall Photoshop CS6 on my new computer when to enter my KEY I continually get the message "you are not connected to internet?

  I bought a new computer. I reinstalled my Photoshop CS6 leave a DVD, but when I entered the serial number I get the message "you are not connected to internet" while I was.  I have "pussy" with Naveen on customer support and after 20 minutes he told me to go to the following link and reinstall through it: http://www.adobe.com/sea/downloads/other-downloads.html

  
  

  This led to the same exact scenario only it took me over 2 hours to download CS6. I then contacted the 'Support Portal online' to ask for additional help. It was 2 days ago and I still have to be contacted and assisted with my problem. Any help or ideas out there?

  Here is what is in the file "hosts":

  127.0.0.1 localhost

  127.0.0.1 activate.adobe.com

  127.0.0.1 practivate.adobe.com

  127.0.0.1 ereg.adobe.com

  127.0.0.1 activate.wip3.adobe.com

  127.0.0.1 wip3.adobe.com

  127.0.0.1 3dns - 3.adobe.com

  127.0.0.1 3dns - 2.adobe.com

  127.0.0.1 adobe - dns.adobe.com

  127.0.0.1 adobe-dns - 2.adobe.com

  127.0.0.1 adobe-dns - 3.adobe.com

  127.0.0.1 ereg.wip3.adobe.com

  127.0.0.1 activate - sea.adobe.com

  127.0.0.1 wwis-dubc1 - vip60.adobe.com

  127.0.0.1 activate - sjc0.adobe.com

  127.0.0.1 lm.licenses.adobe.com

  127.0.0.1 192.150.14.69

  127.0.0.1 192.150.18.101

  127.0.0.1 192.150.18.108

  127.0.0.1 192.150.22.40

  127.0.0.1 192.150.8.100

  127.0.0.1 192.150.8.118

  127.0.0.1 209-34-83 - 73.ood.opsource .net

  127.0.0.1 3dns - 1.adobe.com

  127.0.0.1 3dns - 4.adobe.com

  127.0.0.1 3dns.adobe.com

  127.0.0.1 activate - sea.adobe.com

  127.0.0.1 activate.wip.adobe.com

  127.0.0.1 activate.wip1.adobe.com

  127.0.0.1 activate.wip2.adobe.com

  127.0.0.1 activate.wip4.adobe.com

  127.0.0.1 adobe-dns - 1.adobe.com

  127.0.0.1 adobe-dns - 2.adobe.com

  127.0.0.1 adobe-dns - 3.adobe.com

  127.0.0.1 adobe-dns - 4.adobe.com

  127.0.0.1 adobe - dns.adobe.com

  127.0.0.1 adobe.activate.com

  127.0.0.1 adobeereg.com

  127.0.0.1 crl.verisign.net

  127.0.0.1 ereg.wip.adobe.com

  127.0.0.1 ereg.wip1.adobe.com

  127.0.0.1 ereg.wip2.adobe.com

  127.0.0.1 ereg.wip3.adobe.com

  127.0.0.1 ereg.wip4.adobe.com

  127.0.0.1 hl2rcv.adobe.com

  127.0.0.1 ood.opsource.net

  127.0.0.1 practivate.adobe.ipp

  127.0.0.1 practivate.adobe.newoa

  127.0.0.1 practivate.adobe.ntp

  127.0.0.1 tss-geotrust - crl.thawte.com

  127.0.0.1 wip.adobe.com

  127.0.0.1 wip1.adobe.com

  127.0.0.1 wip2.adobe.com

  127.0.0.1 wip3.adobe.com

  127.0.0.1 wip4.adobe.com