I want to config for different starting power and battery

Similar Questions

• Tecra S2 - power and battery LED flashes - no start

  G ' Day at all.

  I have a TECRA S2 under XP SP3.
  Everything was fine until I went to a place of friends with her and plugged into the power supply and it lights up not at all and no LED.

  I removed the battery and then tried again and then happen to the power and battery LED flash together, but nothing else.

  Tried several times with the battery inside and out with the same results.
  I have stabilize power before removing or installing battery.

  Do not even have BIOS or a screen. I put the HARD drive in a caddy, and it's accessible.
  See you soon
  kb3500

  > Everything was going well until I went to a place of friends with her and plugged to the power
  Did you use the right adapter?

  To be honest, it looks like a malfunction of the power supply motherboard maybe electronic issue of power.
  the power indicator would start flashing amber if the AC adapter voltage is abnormal or failure of computer power supply.

• I want to open two different pdf documents and view them at the same time so I can read about everything by watching the other document.  I use Acrobat DC and whenever I open a document it creates a tab and I can only examine a document at a time.

  I want to open two different pdf documents and view them at the same time so I can read a whole watching the other document.  I use Acrobat DC and whenever I open a document, it creates a tab and I can only examine a document at a time. Is it possible to display two or more documents without having to toggle tabs?

  Don't think that will work, but you can drag the tab to a new window. Each window can have a set of tabs.

• Example config for 2 management vlan and ip Routing.

  We have a stack 6224, we use two vlan on it

  VLAN network 10.1.1.X 24 10

  VLAN network 192.168.0.X 24 40

  Our workstations reside also in the 10.1.1.X network, so we need to administer the switch there.

  192.168.0.X traffic must be routed to 192.168.0.X (and vice versa)

  How can I set this up, when I set up a 10.1.1.1 address for the administration interface and vlan 10 I can't configure the routing for this vlan?.

  (Actually I don't want to just out-of-band of our lan fault management)

  Please advice,

  Message edited by OnnoB on 08/09/2008 06:39
  
  

• synchronization: How can I store the mails for different accounts remotely and manually copy the most important e-mails in local folders on both devices?

  Hello. I have two machines and two accounts, so what I want is this:
  I want only to store mail from two accounts in a remote place and copy more important mails to local folders.

           (I will be grateful for any ideas as to where/how this "cloud" can be - specially free places)
           * Can I have a copy of these local folders in both devices and the remote storage?
           * Could i synchronize devices so that: when i move a mail to a local folder in any device, its copied to the same folders in
              the other device and the remote storage place?
           * The remote storage place will have many other folders. When I open Thunderbird, I also want to see these and the mail
              inside, and also be able to move mail from the inbox to these folders.
            * One of the accounts is gmail. In Account Setting tool, there is an option for synchronization. If there is no easier way, I can have mail for other account copied to gmail, and just syncronize gmail mail. For this, how will I copy my present folder structure to gmail. And how can I syncronize the local folders on the two devices?
  

  Thanks in advance.

  The first awkwardness that I see is that there is no clear format in which to store the messages remotely such that you can work with them in an email client. It may be possible to set the option "Local Directory" of the account in Thunderbird to point to a remote folder (DropBox comes to mind) but I've never tried, and I'd be nervous about what happens if the connection cannot be established, or if you happened to access it simultaneously from two different locations. The other concern is that mail stores are fast becoming big, and you would be forever download and download large files (several gigabytes). Thunderbird stores what looks like a folder that contains many messages separated as one big file, so there is no simple possibility of incremental changes to load up/down.

  The idea of local folders in Thunderbird is to detach messages from servers, therefore they do not follow what is happening on the servers. I say this to emphasize the distinction between files stored locally and permanently ("Local Folders"), against copies cached files online ("synchronized"). It is not sure to consider your folders synchronized as permanent.

  So folders synchronized on an IMAP server are "mirrored" in Thunderbird you do not have a local (although temporary and transitional) copy of messages. This is done primarily to avoid download repeatedly the messages if you re-read, and it makes the fastest search more effective. But these "synchronized" track of message that are deployed on the server, and so if they are deleted from anywhere, all devices that are synchronized at one point also see messages deleted endangered. (Except if you have saved a local copy on the local folders account).

  I use a gmail account quite as much as you described; Copy or move messages to this account, so that they are visible in my phone, my tablet, my own laptop and my computer works. It's free, and it is "in the cloud"; the only reservation I have is her private life. There are other suppliers (e.g. 1 & 1/gmx) who do not seem to have the fetish of collecting data that google thrives.

  It's pretty simple to create filters in Thunderbird to automatically copy messages to your account "cloud." even better is to implement the translation of rules on the servers of other accounts, to ensure that your messages are automatically sent and waiting for you when you log in next time, already in the cloud account.

• RMT-b126a entry for TV Insignia power and TV program?

  bought the BDP-s3200 and it came with a remote (RMT-B126A) that the TV input and power buttons. I want to know if there is a way to program my remote to work with my Insignia TV.

  Hi linksama,

  Your Blu - Ray player's remote control is not compatible with the TV you have. You can refer to page 43 of the operating manual for a list of compatible televisions.

• Different WiFi speed with power and battery

  Hello

  I have a 4 Mbit adsl connection, I noticed that when the laptop is connected to the power, the browsing speed is very fast, when powered by the battery the speed drops to 5-6 KB/s.
  There are a few settings to solve this problem?

  Thank you

  Hello Fabio

  It s a question strange, but everything first, you can check the power settings in the properties of the wireless card. Please, go to the Device Manager and right click-> properties-wireless network card.
  There you should find a tab advanced. All parameters must be defined on the default usage and high value.

  Best regards

• I Bay a labtop to 08/01/2009 with windows vista I want to ubgrade for windows 7 free and how _

  Hallo

  http://www.Microsoft.com/Windows/buy/offers/upgrade-option.aspx

  Above Microsoft link has info for the Options to upgrade Windows 7 from participating computer manufacturers.

  Read the info here to see if you qualify.

  http://www.Microsoft.com/Windows/buy/offers/upgrade-FAQ-option.aspx

  FAQ about the upgrade is at the link above.

  http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

  Windows 7 Upgrade Advisor.

  http://TechNet.Microsoft.com/en-us/library/dd772579 (WS.10) .aspx

  Railways upgrade to Windows 7 at the link above.

  For any other question of Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 forum for questions on windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Want to fax with Windows XP, but he wants the CD for it to work and I don't have it.

  I want to fax using Windows XP.  When I try to set up and configure, a message appears that I have to use the Windows XP CD to continue.  I do not have this CD more.  What can I do to make it work.  He also says that I can use a network server.  I don't know what it is and how to use it.  Can someone help me?

  Hi TerrieStamey,
   
   
  -What, exactly, is a transcript of the error message?
   
   
  Try the steps listed in the articles below and check if it helps.
   
  Faxing in Windows XP
   
  How to enable and configure the fax service in Windows XP
   
  HOW to: Solve common fax problems in Microsoft Windows XP
   

  Kind regards

  Divya R - Microsoft technical support.

• Satellite L455 - plug-and - battery LEDs power LED and it flashes orange

  I have a Satellite L455, which worked perfectly for more than six months now, but two weeks ago he began to behave strangely.

  I turned off the machine normally in the evening I was going to sleep. In the morning when I turned on it it turned on, HARD drive and on power LED blinked blue for a few seconds then they are gone. Machine does not start. I tried to turn it on again and it does the same thing. Then I saw the "power plug on" and "battery on" LED flashes orange at the same time. I unplugged the power adapter. Both lights were continuous blinking but machine will not feed. I removed the battery for a piece of 5 minutes, then reinserted it and the machine has worked all day.

  I went he deleted off the power plug and the morning again it wouldn't start until the when I removed the battery for a few minutes then it works again. The battery recharges very well that when I remove and reinsert it even without connecting the power cable still lights up and works perfectly.

  Then, I removed the battery and the power supply Plug and you press the power button for 30 seconds to unload the machine and then return power and battery and it worked until I turned off again and shutting off the power and then it didn't once again.

  If I stop just of machine and do not turn off the power cord, then I can turn it back on to and work with the machine without hassle even for three days without interruption.

  What could be wrong? Any help will be really appreciated.

  Concerning
  Yusuf

  Hi chidzungo,

  It must certainly be a hardware malfunction but he s strange why it pops up every day after you have closed the laptop. Do you use batteries and AC/DC to original Toshiba adapter? Have you connected external devices to your laptop? If so delete them before you turn on your laptop.

  What version of BIOS is installed at the moment? You should look on the Web from Toshiba website for an update. Update of the BIOS might also help and it s worth a try.

  Before you start reading the BIOS BIOS update instructions update [HERE: http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=60]

  Satellite L455 seems to be an American model, so the BIOS update can be downloaded from the Toshiba U.S. page but first check the exact part number:
  http://www.CSD.Toshiba.com/

• BlackBerry Smartphones bb9900 - icons for the native tasks and memopad apps can be moved to the home screen

  I want the icons for the native "tasks" and "Notepad" apps in OS7 appears on the home screen of my BB9900.  The icons currently on the "common" screen only and the apps work from there.

  I've tried holding down the button menu until a menu jump to the top, but the menu does not include the options of 'move' or 'move to folder '.  In fact, the options of 'move' do not seem to appear for all elements of the 'common' screen

  Someone knows what to do?  FYI, I use the version of the b-berry for Mac desktop software.

  Bernie

  Hello

  "Frequent" is a dynamic screen; your BB automatically there are some things that you use frequently. There is therefore, no manual way to move that you describe (since its automatic and dynamic, based on your usage). On the contrary, what you find is the master for these applications... icon probably they are inside your "Applications" folder, normally visible on the screen "All".

  Good luck!

• Brand new dv7-7212nr want missing SW or config for SSD?

  Just bought a new non-custom desire dv7-7212nr 2 days ago.  Main specifications are:

  3rd gen i7-3630QM

  750 GB 7200 RPM HARD drive

  Drive hard acceleration Cache 32 GB SSD

  8 GB OF SDRAM

  Windows 8

  Other components are irrelevent to my questions or situation.

  The wording 'Hard Drive Acceleraton Cache 32 GB SSD' spec would mainly means the technology Intel Rapid Storage, perhaps combined with the Intel Quick start technology.  Yet, on this computer, I can find only an Intel Rapid Start Technology Manager.

  In Panel of-> system and security-> administration-> computer management tools > storage-> disk management, I can see disk 0 to 699 GB with several partitions, which include the OS (C) and (D) RECOVERY.

  Disc 1 has proved to have an 8 GB partition.

  I find that disk 1 is the SSD and this computer has only the Intel Rapid Start SW technology and configuration.  I read on the internet for this tech in fast ignition to work, an SSD should have a partition that is exactly the same size as the SDRAM.

  My first set of questions are: 1) is my correct conclusion? (2) how HP put in an SSD of 32 GB and uses only 8 GB of it?

  I chatted online with an HP support who asked me to download from a website for HP Intel Rapid Storage Technology and SW drivers and assured me that the installation would not cause any problems or conflicts with the existing configuration, and so I did.  I have no ill effect (yet), but it doesn't seem to be that a good effect is.  On the one hand, it is supposed to be a new 'Intel Rapid Storage Technology' application, but there is none.  So HP support and I can not go further, and support suggested that I do a system recovery, return the setting to factory.  I told him the computer is 2 days, and I to him did nothing other than downloads, that he asked me to do.

  My next set of questions are: a) HP wouldn't put in quick start and quick storage in this product, taking into account the SSD of 32 GB? (b) is there a way to add storage now fast SW and config to envy dv7-7212nr to fully use the 32 GB of SSD? (c) do I keep off to pass my own files on this computer before the problem of cache SSD?

  Finally, I did the Windows experience index runs on the computer and got a score of 5.9 on performance of the hard disk.  I read on the internet that the score is in line with the performance of disk HARD 7200 RPM, which suggests no effect of cache SDS.

  I realize I'm putting in a long post, but I wanted to provide enough information for the experts to evaluate and give answers.

  Thank you very much!

  XLIU wrote:

  So, how do I know / check / detect that the other 24G of the 32 GB of SSD is used for the RAID config? Thought that the RAID has not SSD.

  I looked at the config of the BIOS at startup; It shows no option for TSRI but only Intel Rapid Start Tech. It seems that the dv7-7212nr want to support any, TSRI unlike advertising on the dv7-7212nr box.

  First of all, make sure that you download and install the driver of technology Intel Rapid STORAGE for the Envy HP dv7-7212nr here:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-112591-1&cc=us&DLC=en&LC=en&OS=4132&product=5309489&sw_lang=

  After installation, find Intel Rapid Storage Technology and run. It must start with a screen that looks like this:

  

  It's my real desire HP dv7-7212nr. The screen may be slightly different from mine because I fiddled with technology Intel Rapid Storage Technology (for example, the default Cache volume is 22 GB, where, as mine said 21 GB). Although the WSSD is 32 GB, the size displayed in the Windows is always less than the specified size (30 GB instead of 32 GB). Similarly, the 750 GB hard drive is displayed as GB 699.

  As you may already know, the 8 GB data volume is configured as a partition hibernation for Intel Quick START technology, and the rest, 21 GB in my case, is used as cache acceleration to Intel Rapid STORAGE Technology. The status of SATA (750 GB HDD) drive "fast-track" means that the hard drive is "fast-track" by the cache on the SSD drive and that it is configured and working properly. You can easily change these settings if you take the time to read and learn about it; for example, you can disable the quick START (hibernation partition) and use the whole SSD for fast STORAGE (acceleration).

  Your BIOS should certainly have an entry indicating the Intel Rapid STORAGE technology works properly. I forgot the exact name of it, but I will edit this post to let you know what he said exactly once that I reboot to enter the BIOS again.

  Edit: In the BIOS, go to System Configuration > UEFI Device Configuration (under Intel Rapid Start technology) > technology Intel Rapid Storage Technology and you should see a screen similar to mine below:

  

  As you can see, I've fiddled with my setup of the WSSD, and so my quick partition start (hibernation) is in fact 8.3 GB (slightly larger than the default value) and my cache volume is 21.5 GB (slightly smaller than the default value).

• How do I set the power for different time?

  Hello everyone,

  I try to set the different value of RF power for different time as shown in the figure. To do this, I tried using the timer 'Elapsed time '. A counter that counts each time is an array index, as shown in the attached VI. But, the meter does not not.  I didn't know what went wrong. would you lelp me please?

  I thank very you much.

  I would like it.

  

• SkyDrive, I created a folder, the names of 'recipes', I want to drop this file into categories for different types of food.

  If I create a folder called 'recipes' is it possible to create a path to break the categories, e.g., beef, pork, etc.

  SkyDrive, I created a folder name "recipes", that I want to drop this file into categories for different types of food, i.e. beef, pork, biscuits, pies, etc.  Is this possible?

  You can get help with Windows Live here services: http://windowslivehelp.com/forums.aspx?productid=6

• Eclipse Plugin config changes for different versions of the target operating system.

  Nobody knows what changes should I make for my config Eclipse generate a cod for different target operating system versions?

  Thank you

  Glenn

  You can configure it by clicking in the window menu, selecting Preferences, expand BlackBerry JDE, selecting installed components and choose the appropriate BlackBerry JDE or BlackBerry JDE component Package.