Impossible to get Dell Optiplex 9010 to start using Windows 7 DVD

Similar Questions

• Impossible to get access to change printer cartridges using windows 8

  Hi-

  Have new HP computer running windows just 8, have connected before printer Epson SX200, alls been good so far, except printer ran out of ink - have tried all means to get to the maintenance of the printer etc, so to change BUT can't please, anyone

  Support of Epson is the best place to get help with this. -Basically, turn on the printer and lift up the scanner with the bottom cover to access the ink. Press the button to open the ink tank, you do not need to use the maintenance. Here's a poor video that shows you how. You can't see much in the video, but you can follow the verbal instructions-

  http://www.YouTube.com/watch?v=eCFNXssl5U0

• I get an error when I start up windows.

  I get this error whenever I start up windows. http://i.imgur.com/CQ3mDUP.PNG

  Caused by a program that you have installed, a game or crack maybe?

• Dell Vostro 5470 not get Dell Logo after update bios in Windows 10

  Dell Vostro 5470 not get Dell Logo after update bios in Windows 10.

  Laptop computer has restarted:

  1 Fireed power led,

  2 Powered hard drive for 2 seconds to turn it off.

  3. stops...

  No Dell Logo, no beeps, can't go in the Bios.

  Test LCD works OK.

  Remove the module of Ram, power on and listen to beep

  Pressing the END key and power for laptop has no effect.

  Any idea?

  Yes. I did it.

  Laptop have bios Phoenix.

  Phoenix Bios have restored the USB Flash procedure.

  This procedure to restore the BIOS:

  1. download USB flash less than 4 GB.

  2 format in FAT.

  3. get your flash update of the Dell store - xxxx.exe

  4. run cmd.exe and in the command prompt, run /writehdrfile xxxx.exe

  5 extracted copy of Bios.cap for the flash player.

  6. turn off the power to the laptop.

  Next 7,8 step may not be necessary but I did it.

  7 disconnected all perihpericals with battery and charger.

  8 disconnect the HARD drive

  9. connect the USB on the laptop on the right side.

  10 press and hold the END

  11, Pluged the power cable and the relase the END key 1 second after the power cord is in.

  12 USB led on stick flashed quickly and we see the process of recovery of the Bios on the screen.

  13. After finishing laptop restarts and worked well.

• just started using windows live mail and it strips attachments PowerPoint, I receive. How can I change this?

  just started using windows live mail and it strips attachments PowerPoint, I receive. How can I change this?

  Hi hanksterman,

  The question you posted would be better suited to the Windows Live community. Please visit the link below to find a community that will provide the support you want.
  http://windowslivehelp.com/product.aspx?ProductID=15

• Dell Optiplex preinstalled suddenly not genuine Windows 7

  One of the clients in another office has notifications that Windows is not genuine.
  It is a Dell Optiplex with Windows 7 pre-installed pro.
  Have you tried to rename token.dat to no avail, have no version of work in previous versions, either.

  Here is the result of MGADiag:

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->

  Validation code: 0x8004FE21
  Code of Validation caching online: 0x0
  Windows product key: *-* - M3DJT - 4J3WC-733WD
  The Windows Product Key hash: xo + ajVSpae7/4VoZjS7m6JL0f3A =
  Windows product ID: 00371-OEM-8992671-00524
  Windows product ID type: 2
  Windows license Type: OEM SLP
  The Windows OS version: 6.1.7601.2.00010100.1.0.048
  ID: {7B308069-D7B5-4A24-947B-C02DD28ECBF1} (3)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows 7 Professional
  Architecture: 0x00000000
  Build lab: 7601.win7sp1_gdr.140303 - 2144
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  OGAExec.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 109 n/a
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program may Explorer\iexplore.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->
  [File mismatch: C:\Windows\system32\wat\watadminsvc.exe[7.1.7600.16395], Hr = 0x800b0100

  Other data-->
  Office details: {7B308069-D7B5-4A24-947B-C02DD28ECBF1}1.9.0027.06.1.7601.2.00010100.1.0.048x 32*-*-*-*-733WD00371-OEM-8992671-005242S-1-5-21-2233106378-2874483989-3976642890Dell Inc.. OptiPlex 380 Dell Inc.. A07 20120613000000.000000 + 00070213A07018400F804130409Europe West Standard Time(GMT+01:00)13DELL B10K 109

  Content Spsys.log: 0 x 80070002

  License data-->
  The software licensing service version: 6.1.7601.17514

  Name: Windows 7 Professional edition
  Description: operating system Windows - Windows (r) 7, channel OEM_SLP
  Activation ID: 50e329f7-a5fa-46b2-85fd-f224e5da7764
  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
  Extended PID: 00371-00178-926-700524-02-1033-7601.0000-3072011
  Installation ID: 015974943375231746024253831654680220569181086526553500
  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
  Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
  Partial product key: 733WD
  License status: licensed
  Remaining Windows rearm count: 2
  Trust time: 09/05/14 13:09:28

  Windows Activation Technologies-->
  HrOffline: 0x8004FE21
  HrOnline: n/a
  Beyond: 0 x 0000000000000001
  Event timestamp: 9:5:2014 13:07
  ActiveX: Registered, Version: 7.1.7600.16395
  The admin service: recorded, Version: 7.1.7600.16395
  Output beyond bitmask:
  Altered the file: %systemroot%\system32\wat\watadminsvc.exe

  --> HWID data
  Current Hash HWID: NAAAAAEAAwABAAQAAAABAAAAAQABAAEA6GEsomZHPnaqdsrnEBjOcKQLrCskQ7K0rE5Gyg ==

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes
  Windows marker version: 0 x 20001
  OEMID and OEMTableID consistent: Yes
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  APIC DELL B10K
  FACP DELL B10K
  HPET DELL B10K
  STARTING DELL B10K
  MCFG DELL B10K
  SSDT DELL st_ex
  TCPA DELL B10K
  _ DELL B10K
  DELL SLIC B10K
  SSDT DELL st_ex
  SSDT DELL st_ex
  SSDT DELL st_ex

  Close all open windows.

  Open a command prompt window, and then type the following command

  WUSA / uninstall /kb:971033

  and press the Enter key

  Accept updates in guard/confirmations and wait only to complete

  Copy and paste the result (if any) in the command prompt window to an answer here.

  Reset

  Reinstall the update of http://support.microsoft.com/kb/971033

  Reset

  run another MGADiag report and post it.

• Impossible to send, reply to or forward emails using Windows Live Mail

  Impossible to answer, send or transfer emails using Windows Live Mail since that it has been updated about a week ago. I now get the error: 0xC00CE508 plus a number whole errors listed under failed to initialize the canvas part I use Windows 7.

  I suggest you re-check your e-mail provided by your ISP settings.

  Also, your probably better poster on forum Windows Live to help...

  http://www.windowslivehelp.com/

  MS - MVP Windows Desktop Experience
  "When all else fails try what the captain suggested before you started...". »

• Impossible to copy files to the Sansa Fuze using Windows 7 (drag and drop, or Windows Media Player)

  Hello

  Yesterday, I bought the Sansa Fuze and I have problems copying files to the device using either Windows Media Player (Sync) or Drag and Drop (Explorer).

  The symptoms are:

  (1) the device is recognized and available in Windows 7 (Series USB MSC - sorry don't have it with me right now)

  (2) took me to upgrade to the latest firmware, which has worked flawlessly

  (3) when I try to drag and drop a file on the device (I use Windows 7, 64-bit), it starts, but doesn't seem to calculate the size of the files or waiting time to download correctly.  It is followed by a slow progressive, until the computer crashes, resulting in a constant 100% of the CPU.  The only solution is a hard reboot

  (4) when you use Windows WM, the device is recognized, okay and the synchronization starts, but it then stops without reason.  Once again, the processor springs and requires a reboot

  (5) using the results 3 and 4 in 1-5 files being copied across, but not more.

  (6) I tried several albums and one album at a time, but cannot determine if that makes a difference.

  Help, please!

  See you soon,.

  Richard

  It may be a bug in Windows 7. But one thing to try is to go to the Device Manager (assuming that Windows 7 still has), uninstall the "rocket" (under USB controllers), and then run add hardware to find and reinstall the driver.

  Use the MTP with Windows Media Player mode, MSC mode without.

• How to get my computer default to Microsoft using Windows 8.

  Hello! I am trying to set my default settings of the computer to Microsoft, I can use my Microsoft email and send a video webcam. I went into the control panel and went in select default and changed computer for Microsoft and press OK.  But then he said he wet his default values in windows media player and when I went in my webcam to send my email it says that it has not been implemented for email. So, why it does this? It takes a few minutes to Setup? Any input would be greatly appreciated!

  You may or may not know that Windows Vista was the latest OS to come with a desktop e-mail program.  Windows 7 and 8 do not come with any successor to the Windows Vista Mail program.  Instead, you can get it as a download in the Windows Essentials page option.  Of course, Windows 8 has a rudimentary basic e-mail application, but it is designed for the Tablet/phones and the lamp.  If you want something that compares to the program post Vista (for example the possibility to send e-mails from office based programs such as your webcams), you'll want to get the free download of the essential elements in this link before you move forward.  Then it will work fine.

• Impossible to get a new SSD to start

  My iMac 2009 HD is dead, but I had a Time Machine backup. I replaced with a new 1 TB SSD HD death and thought I just plug the TM backup and start over. Well... I guess it doesn't work like that. I tried searching the net and found instructions to supposedly solve my problem, but they have not worked. I tried to start up taking Cmnd R, but that has not worked. I'm sure I have no CD from when I bought the iMac to my boss, while the option is out. I have an old iMac (predecessor of it) that I used as a system until I could get it fixed. I "think" I inferred that I can copy somehow the OSX from the old machine, I used it on my external hard drive which has my TM backup on it. So I think I somehow transfer that to the new SSD. Is that guess correct? If so, how can I get the operating system on the external hard drive (shouldn't it already be there as part of the TM backup?). So, how do this OS on the new SSD?

  Thank you

  You formatait the new SSD?

• Impossible to get 2008 Macbook at the start of the recovery of the Internet... help?

  I tried the command + option + R and command-R start-up and restart, but no dice. I'm trying to reinstall Mac OS to give the laptop to a friend. Any tips?

  Hey Sndietzel,

  Thank you for being a part of the communities of Apple Support.

  I understand your message you are trying to boot a MacBook (2008) for OS X Internet Recovery but it is not successful.  This happens because this year and model of Mac does not support the OS X Internet Recovery:

  Computers that can be upgraded to use OS X Internet Recovery

  What version of Mac OS X is currently installed? In the menu bar select  > what the Mac and you should see the version of OS X installed.  If she has OS X 10.6.8 or more, then there is no OS X Recovery, and you will need the installation disk OS X, or the disc that came with the computer to erase the disk and reinstall OS X. You will need to insert the disc while the Mac is turned on, and then restart while holding the C key to boot the disk.

  Take care.

• Impossible to get Dell PC Diagnostics to run

  System details: Dell Inspiron 15R (no touch) less than 3 months; Windows 8, 64-bit; IntelCore i3-3227u 1.90 Ghz, 6 GB ram, 450 GB hd; added to install software: Bitdefender Internet Security 2013, 2013 Office, Chrome (28.0.1500.72 m), Trillian, ICQ, PDF-Viewer, IE 10, Brother printer utilities.

  Problems with a graphics accelerator blue screen and tried to run Dell Diagnostics PC online (by PC-Doctor) to try to diagnose the problem, but cannot enforce. Select the type of scan (have tried all), accept the license agreement, click 'Yes' to run Dell system to detect and BOOM, download super random and vague error: "a problem has been detected, please try again" (extra space before the comma typo Dell).

  Have tried this via Chrome and IE. Have tried this after disabling antivirus and firewall. Nada.

  Any suggestions?

  In case it helps, the original problem is a blue screen in recent weeks, saying something like "Intel graphics accelerator display drivers for Windows 8 (R) stopped responding and has recovered," which freezes the laptop, requiring a hard reboot. It seems to happen pretty regularly now, often when I'm in the middle of working on a Word document with a bunch of open tabs in Chrome and Bitdefender, commercial brother and Trillian running in the background.

  Thank you for any input!

  Try resetting your Internet Explorer settings, also if you install Dell system detects, right click on the .exe file and run as administrator.

• OfficeJet Pro 8600 USB, Dell OptiPlex 9010, Windows 7 Pro, 64-bit. Printer hangs sporadically.

  Printer and the computer are less than six months. All the drivers for the printer and the computer have been updated at the latest. BSOD occasionally when printing HP JO, but not in network Xerox printer/copier. Some recent error messages:

  Event ID: 808

  The print spooler could not load a plug-in module C:\Windows\system32\spool\DRIVERS\x64\3\UNIDRVUI. DLL, error 0xc1 code. See the user context information for event data.

  The print spooler could not load a plug-in module C:\Windows\system32\spool\DRIVERS\x64\3\PS5UI. DLL, error 0xc1 code. See the user context information for event data.

  Event ID 372:

  The Microsoft Word document - xxxxxx.docx, held by CJones, failed to print on printer HP Officejet Pro 8600. Try printing the document again, or restart the print spooler.

  Data type: NT EMF 1,008. Spool file size in bytes: 307056. Number of bytes printed: 307056. Total number of pages in the document: 6. number of pages printed: 0. Client computer: \\ASEAPC19. Error code Win32 returned by the print processor: 2147500037. Unspecified error

  I ran doctor Scan and printing and printer install wizard for Windows - "everything out ok with your product." "The current full HP software is already installed and drivers seem to be installed correctly.

  Appreciate any help you may be able to offer.

  Cathy

  Hello Cathy

  Unplug the printer from the computer and follow the instructions below. Let me know the results.

  1. Go to add/remove programs.
  2. Uninstall Officejet Pro 8600. If you see the other programs related to the 8600 Officejet HP remove them as well.
  3. Make sure you have the latest version of Adobe Flash installed.
  4. Restart the computer.
  5. Go to devices and printers, select any printer, then click Properties of (top-right) print spooler, click the drivers and make sure that the driver for the 8600 is gone.
  6. Download the latest driver for your printer and reinstall.

  Sources:

  HP C5180 printer will not print using spooler after upgrade to Windows 7 (64-bit)

  Error code Win32 returned by the print processor: 2147500037. Error__ not specified

• Cannot get my dell A920 printer to print using windows 7, it will scan but not print. It is said it can not print, but may not know why when troubleshooting

  I can't get my dell A920 to print.  It scans but does not print.  The reasons why CN can't find troubleshooting.  Help

  dosducexx,

  First run, delete print jobs to eliminate any print job stuck in the queue.

  Unplug the printer.

  Download and run the patch (cleaning printer utility) until it prompts you to restart your computer.

  Restart your computer. Make sure that the printer is deleted. Deleting Manual printer driver

  Download the 32-bit drivers for Vista for Windows 7 32-bit or 64-bit drivers for Windows 7 64 bit Vista. Install the Vista drivers in Vista compatibility mode, you will get a message, the printer is not connected. Connect the printer at the moment (power on).

  You will find links to the patch/drivers to...

  Owners of printer inkjet all-in-one Dell A920 thread (W7)

  Don't forget the programs anti-virus and firewall will block communications.

  Rick

• Impossible to get a contact with my 33120 using GPIB-USB-HS

  I got the 2010 version of labview pogram. trying to connect the signal generator to my computer through a GPIB cable / USB but can't very well my camera in the max and not even the icon DEVICES AND INTERFACES. Is there something I need to install on my computer?

  Yes,

  You must install the device drivers.  You can download them from here