Impossible to get my 3560G switch talk to ESX 3.5 and the EMC NAS servers.
I tried for the past two weeks to get my 3560G switch to talk to a couple of ESX 3.5 servers, but VC and the EMC NAS. The goal is to implement 2 Etherchannels on the physical switch and aggregation of NETWORK cards on the vSwitch. A port-channel will have 1 VLAN it crosses, and the other port-channel will have 2 VLANS across it. VLANS have been implemented on the vSwitch mirror the VLAN I have on the 3560G. I want to (have to) use the load balancing. Also, I read other forums and websites to get ideas on how to implement, and every solution is different from the other. The problem seems to reside mainly in the configuration of VLAN on the physical switch in my humble OPINION, because if I just switch a switch, dummy can talk without problem. The following information, I already know, not because it's my requirement, but rather the parts that must be present for the entire configuration to succeed.
All interfaces in an Etherchannel must belong to the same VLAN or considered trunks. I take this means that for the second port-channel, I have to configure interfaces as the trunks, since I need 2 VLAN different to go the link. -I tried to configure them as trunks and the ports of access, and none seemed to work.
vSwitch must be configured to "Route based on the hash of the intellectual property."
port-channel - the load balancing must use the src-dst-ip option.
FlowControl receive desired must be set
Jumbo mtu 9000 system must be set to
Here is an excerpt of my configuration:
src-dst-ip port-channel load-balance
No file verify auto
pvst spanning-tree mode
spanning tree extend id-system
!
internal allocation policy of VLAN ascendant
!
Interface Port-Channel 1 - Port-canal2 is configured similarly to this one.
switchport trunk dot1q encap
switchport vlan trunk native 2
switchport trunk allow 3 - Po2 allows instead of VLAN 4.5
switchport mode trunk
!
interface Gigabitethernet0/1-gi0/1 - 20 are configured similarly to this one.
switchport trunk dot1q encap
switchport vlan trunk native 2
switchport trunk 3 - gi0/13 - 14 permits vlan 4 and gi0/15-20 allow vlan 5
switchport mode trunk
FlowControl receive desired
channel-group mode 1 on
!
Interface Gigabitethernet0/21 - 28 are stop
!
interface Vlan1
no ip address
Shutdown
!
interface Vlan2
IP address x.x.1.2 255.255.255.0
!
interface Vlan3 - 5 are configured identically
no ip address
!
IP default-gateway x.x.1.1
This should be enough to give you an idea about where I am and where I belong. Any information you can provide would be greatly appreciated!
Hello
You config works without using etherchannel?
On the ESX, I think that the vlan native is 0, you describe that?
In addition, you use the 3560 as layer pΘriphΘrique layer-3 2, right?
Reza
Tags: Cisco Network
Similar Questions
-
Downloaded standalone 6 Lightroom on a MacBook Pro. Impossible to get a program to open - an internal error cannot create the required folder. Any suggestions about how to proceed?
Hi woodysk
Greetings.
- You will need to read and write permissions on the Adobe folders manually.
Please follow the steps below:
- Right-click on the icon in the Finder and select the 'Go - To' folder option.
- You will get a text box, type in the following command and then press the 'return '. (Don't miss ~ symbol)
- ~/Library
- Then go to the Application Support > Adobe.
- Right-click on the Adobe folder, then select the GetInfo.
- Expand the section sharing & permissions.
- Click on the padlock icon in the lower corner on the right. Enter your administrator user name and password when you are prompted, and then click OK.
- Please click on '+' symbol, it will open the list of user accounts.
- Add all of the user accounts and then give permission to "Read & write" to all user accounts. (If not agree, just add currently logged in username and administrator)
- Click the gear icon and select apply to closed. Close the dialog box for information.
- Then launch Lightroom application and check.
Let me know if still face you any issue.
Concerning
Rohit
-
How can I get Firefox saves my my hotmail MSN live login and the password
How can I get Firefox saves my my hotmail MSN live login and the password,.
My settings are all correct and must be saving them, but for some reason that it is the only account that it won't save.Hello
1. what version of Firefox are you using?
I would recommend that you follow the steps in this article.
http://support.Mozilla.com/en-us/KB/make-Firefox-remember-usernames-and-passwords
-
Impossible to get Internet after put in a new hard drive and reinstall XP
Thank you very much Bev. I now have access to Windows (c 9/30/08-Dimension E310 - NO BOOT DEVICE AVAILABLE!) but I can't get online cus my XPS 210 is my main and routed computer to the modem. My router cannot detect a connection to local access to the Dimension E310 and Linksys tech team claims that the router works fine cus, it shows the two comps connected r, this is the 2nd computer (Dimension E310) that does not allow a connection to access online. Network connection screen is empty with no LAN/local access icon.
I downloaded all the drivers and applications from the E310 Resource CD. Why the Dimension E310 doesn't read the router?
Thank you
-
I'm getting "0xC004C003 key is blocked" in my event viewer and the 'not genuine' wallpaper
Suddenly, my windows is not valid. I get 0xC004C003 key is stuck in my event viewer. It is a copy, I bought on amazon last year, installed and ran it for a long time without problems. then 6 months ago or not, this computer crashed, so I installed this copy on my HP workstation. problems of validation then. Ms. helped me then. not activated no problem until now, months later. Another problem is that when I run slui 4, I don't get a chance to choose my country so I can choose a phone number. is there anywhere else I can get the phone number for people of activation? Thank you!
Diagnostic report (1.9.0027.0):
-----------------------------------------
Validation of Windows data-->Validation code: 50
Code of Validation caching online: 0xc004c4a2
Windows product key: *-* - 74XYM - BH4JX-XM76F
The Windows Product Key hash: KeYfcvXg/a1Q01x73 + f8IL/JC4Y =
Windows product ID: 00359-112-0000007-85023
Windows product ID type: 5
Windows license type: retail
The Windows OS version: 6.1.7601.2.00010300.1.0.003
ID: {18CB392B-26DC-497B-9668-B09F494D682E} (1)
Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Product name: Windows 7 Home Premium
Architecture: 0 x 00000009
Build lab: 7601.win7sp1_gdr.110622 - 1506
TTS error:
Validation of diagnosis:
Resolution state: n/aGiven Vista WgaER-->
ThreatID (s): n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002Windows XP Notifications data-->
Cached result: n/a, hr = 0 x 80070002
File: No.
Version: N/a, hr = 0 x 80070002
WgaTray.exe signed by: n/a, hr = 0 x 80070002
WgaLogon.dll signed by: n/a, hr = 0 x 80070002OGA Notifications data-->
Cached result: n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002
OGAExec.exe signed by: n/a, hr = 0 x 80070002
OGAAddin.dll signed by: n/a, hr = 0 x 80070002OGA data-->
Office status: 109 n/a
OGA Version: N/a, 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3Data browser-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default browser: C:\...\Google\Chrome\Application\chrome.exe
Download signed ActiveX controls: fast
Download unsigned ActiveX controls: disabled
Run ActiveX controls and plug-ins: allowed
Initialize and script ActiveX controls not marked as safe: disabled
Allow the Internet Explorer Webbrowser control scripts: disabled
Active scripting: allowed
Recognized ActiveX controls safe for scripting: allowedAnalysis of file data-->
Other data-->
Office details:{18CB392B-26DC-497B-9668-B09F494D682E} 1.9.0027.0 6.1.7601.2.00010300.1.0.003 x 64 *-*-*-*-XM76F 00359-112-0000007-85023 5 S-1-5-21-3265048641-1616023370-2010388088 Hewlett-Packard HP xw9300 Workstation Hewlett-Packard v2.09 786 B 9 20061128000000.000000 + 0000FFC3E07018400F2 0409 0409 Eastern Standard Time(GMT-05:00) 0 3 109 Content Spsys.log: 0 x 80070002
License data-->
The software licensing service version: 6.1.7601.17514Name: Windows 7 HomePremium edition
Description: operating system Windows - Windows (r) 7, retail channel
Activation ID: 2e7d060d-4714-40f2-9896-1e4f15b612ad
ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 00359-00170-112-000000-00-1033-7600.0000-1342011
Installation ID: 001526735912798560462865728640675052531545198973294682
Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
Machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
Partial product key: XM76F
License status: Notification
Reason for the notification: 0xC004F200 (non-genuine).
Remaining Windows rearm count: 4
Trust time: 15/08/2011 11:17:44Windows Activation Technologies-->
HrOffline: 0x00000000
HrOnline: 0xC004C4A2
Beyond: 0 x 0000000000000000
Event timestamp: 8:13:2011 18:29
ActiveX: Registered, Version: 7.1.7600.16395
The admin service: recorded, Version: 7.1.7600.16395
Output beyond bitmask:--> HWID data
Current HWID hash: NgAAAAEABgABAAEAAQABAAAAAQABAAEAln0i8sIGfr2emhaDPo506gCHiHOyirYIkskUxhZfActivation 1.0 data OEM-->
N/AActivation 2.0 data OEM-->
BIOS valid for OA 2.0: Yes, but no SLIC table
Windows marker version: N/A
OEMID and OEMTableID consistent: n/a
BIOS information:
ACPI Table name OEMID value OEMTableID value
HP APIC VIPER
FACP HP VIPER
SRAT HP VIPER
MCFG HP VIPER
HP SSDT PROJECTBTW, the tool says that no identifiable information is captured in these results, but the exact path to my default browser was included which shows my user name and the path to my profile on my machine. Some security people would consider this identification info. I have it redacted sort of above (hope that isn't waste analysis), and it doesn't really bother me, but just a heads-up. Thank you!
J
Activation 0xC004C003 error
How to troubleshoot the error codes Activation Volume Windows 7, Windows Server 2008 and on Windows Vista computers
http://support.Microsoft.com/kb/938450Microsoft Activation centers worldwide telephone numbers:
http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx
(This site is for activating Volume License, but if you call, they will help you)The phone number is not working:
Microsoft Wordwide contacts: http://www.microsoft.com/worldwide/default.aspxActivation and registration of a Microsoft product
http://support.Microsoft.com/?kbid=326851
Windows activation: (888) 571-2048J W Stuart: http://www.pagestart.com
-
Impossible to get rid of Security Suite on my PC (read all the other posts)
Hi guys,.
I also have problems with this security suite. I followed all the guides provided on the site to remove it, but it is always present. It looked as if it had been uninstalled, but returned shortly after the restart. I would rather not reformat my computer because it's a pain so wanted to know if there are other things I could do to remove it. None of the anti-malware programs have worked and I don't really dare to change anything in the registry because I don't know what I'd be looking at and could make things worse.
Thank you!
Sam
Hello
No one program cannot be used to detect and remove any malware. Added that often easy to
detect malware is often accompanied by a much more difficult to detect and remove the payload. If its
better to be too full now than to pay the price much later. Check with these extreme
Overkill point and then run the cleaning only when you are sure that the system is clean.Security Suite and AV Security Suite are fake antivirus, a scam to get you to pay for them
While they have no advantage.Remove Security Suite (uninstall Guide)<-- read="">-->
http://www.bleepingcomputer.com/virus-removal/remove-security-suiteHow to remove AV Security Suite (uninstall Guide)<-- read="">-->
http://www.bleepingcomputer.com/virus-removal/remove-AV-security-suiteIt can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
the regular windows when you can.Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Malwarebytes - free
http://www.Malwarebytes.org/Run the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can download
It's here.Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en-----------------------------
also install Prevx to be sure that it is all gone.
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs.
It is a single scanner, VERY EFFICIENT, if it finds something to come back here or use Google to see
How to remove.
http://www.prevx.com/Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software (viruses,
Trojan horses, rootkits, etc.). that has infected your computer despite all the security measures you
took (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro
--------------------------------------------Here are some free scanners online help if needed:
http://www.eset.com/onlinescan/
New Vista and Windows 7 version
http://OneCare.live.com/site/en-us/Center/whatsnew.htmOriginal version
http://OneCare.live.com/site/en-us/default.htmhttp://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------
Also do to the General corruption of cleaning.
Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlThen run checkdisk (chkdsk).
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Impossible to get sp2 & sp3 on recovered 2006 XP have checked all the settings, they are ok
have followed all the steps on & above and tried to install active x 4 times still can not update recovery xp 2006
Thanks for the comeback. I think that your answer would greatly helped, BUT I solved it myself. Microsoft doesn't make it very easy and does not explain that even if you find and download SP3 you decompress to run anything of him.
My client has their computer back and completely restored & updated for updates for XP. Thanks for your help anyway.
Microsoft Security Essentials, Malwarebytes and Avira included. They learn to run CCleaner Eusing and optimize each month and weekly defragmentation.
Thanks again,CwynnJones the type of computer
PS the sp3 was the problem because it wouldn't install the active X
-
I'm trying to get a style switching to go to my site (for the color palette)
I would like to give my users the choice to change the colors of my site ( http://chaoscoalition.net) at will, through css style, change the buttons such as those on the theme of the forum ( http://forum.chaoscoalition.net).
I read a lot of articles and tutorials on how to put in place the other stylesheets of a Web page, but I can't do the things well. Whenever I have seem to have gotten the right, either open the php file that sets the cookie, or it opens the stylesheet text. I want to end up with something like the forum theme change module, but for the home page.
I have 5 different versions of the done page, just like pages (format php), but I do not understand how to link the buttons at the top to trigger change of style sheet, and I don't even know if it is possible to rely on a css file to change the color scheme of the page (which is based on image).
It would be great if someone could walk me through it, or offer a tutorial that explains how to do from scratch.
Thank you.I have a gross example of a style sheet changer, that put JavaScript in place on this
page. Your CSS can change what you want (color scheme, page width,
etc...).Look at the source code in your browser to see how it is implemented.
http://ALT-Web.com/templates/variable_width.shtml
And the script can be found here:
http://ALT-Web.com/scripts/changesheets.js--
Nancy O.
ALT-Web Design & Publishing
Web | Graphics | Print | Media specialists
www.Alt-Web.com/
www.Twitter.com/ALTWEB/
www.Alt-Web.blogspot.com/ -
Hi all
First Pro CC worked fine on my Macbook Pro the week and last week, he has a problem. I get an image blurred when the video does not play, but when he plays he is clearly going. I can work with that, but the problem is that when I export, I get the same image blurred. I uninstalled the program including the settings and get installed yet and still the same problems.
Any ideas would be a great help.
The image below is a screenshot of the video pause/stop
The image below is a screenshot of the video playback
Hi Tony,.
Go to the file/project settings/general and change the rendering on "Mercury Playback Engine software only" engine.
Kind regards
Navdeep Pandey
-
How to get photos in iPhoto to e-mail using Chrome and the Mavericks
I would like to know how to copy quickly and easily photos that I receive in my email in iPhoto.
I'm running the Mavericks 10.9.5
I use Google Chrome
I have iPhoto 9
I know I must upgrade the operating system to more recent, but do not like change.
Thank you!
Ginny
What is your e-mail client? You should be able to control (on the right) - click on a photo in e-mail and elect to iPhoto import on the shortcut menu that appears. If this isn't an option, just drag the photo on the desk and from there to the iPhoto in the Dock icon.
You know that iPhoto can no longer order any printed products, namely books, cards and calendars, printing products, Apple Store, right? Also if you try to use the location of iPhoto feature it crash like iPhoto 9.4.3 and earlier, use the servers of Google Maps and they are no longer available to Apple.
-
The continuous solitair game give a window saying "hardware acceleration" is disabled. In addition, the game runs very slowly.
Ed,
If you are still having this problem then I recommend to update your video card driver. Go to the website for the manufacturer of the video card and usually they will have a driver download section. Also, if this does not help, then after your system specs and what version of Windows and level of service pack that you are running.
Mike - Engineer Support Microsoft Answers
Visit our Microsoft answers feedback Forum and let us know what you think. -
Can switch you from ESX 3.5 and ESXi 4.0?
We have a host in a remote location running 3.5U4 managed by a VC server in our data center. We would like to upgrade to ESXi 4.0. There is only the local drive and we anticipate using our VC to manage this host more, we just intend to use the vSphere client.
So can we close the virtual machine 1, which currently sits on the host and do an upgrade?
Or should I back up the virtual machine, do a clean install and then restore a virtual hardware and virtual machine / upgrade tools?
Kind regards...
Jamie
If you found this information useful, please consider awarding points to 'Correct' or 'useful '.
Remember, if it isn't one thing, it's your mother...
Hello jamieorth,
Upgrades between ESX and ESXi are not supported. You must perform a clean installation.
See page 25 on attached file.
If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!!!
VSP4, VTSP4, VCP4
ITIL Foundation v.3
-
SSL VPN 25 user license - impossible to get more than 2 SSL VPN connections
Hello
I just installed a user license user Premium 25 for SSL VPN on my Cisco ASA5505. Even though it states that the license is installed I get still only two client Anyconnect SSL VPN connections and the third fails systematically. What Miss me?
Thanks for posting to the forum and that the problem has been resolved, and what caused the problem and what has been done to solve the problem. It's the most useful forum when people can read on a problem and can also read what the problem turned out to be and what was done to solve the problem, I think that it is also a good example to remind us that sometimes, the problem is not in our configuration, or even in the area that we administer. So sometimes we have to look beyond our normal home to find the source of the problem.
The question mark it resolved makes it even more obvious to readers that they will find a solution to the problem. So thank you to mark the issue as resolved.
HTH
Rick
-
Impossible to get VM to talk to eachother
I create my own SCCM VM environment at home using VMware Player. I have a virtual server that is running Windows Server 2008, Enterprise Edition version with SQL Server 2008, AC DC, and SCCM installed. I also have your computer desktop virtual running XP Pro w / SP2 that is joined to the domain I created on the virtual server computer. I'm running both of these s VM simultaneously on a desktop with 6 GB of RAM and a quad processor computer. Neither one of those VMS uses a static IP address. They get the IP address via DHCP from a wireless router. The Office of the host connects via a cable to the wireless router. The router is connected to the Internet.
I would like to be able to access the internet, at least since the server VM and always be able to ping to server VM XP VM and vice versa, by name. But I can't not to come with the right network configuration. I tried different combinations of local bridge, NAT, and configs but I can not quite do things. Heck, I'd be satisfied with just getting the two virtual machines to talk to each other and forget about the internet but I can't seem to understand. (ping is not by the name and IP)
Should I use a static IP address for the server VM or for the desktop and the server? I have to configure DNS on the server and point each for local DNS service? Any advice would be appreciated. Thank you.
Two things to check:
1. is the Windows Firewall completely off? Sometimes, it causes unexpected network problems in both directions (server to Client and vice versa)
2. not NIC 2008 appear as belonging to networks not identified in the network settings UI? If so, Windows is supposed to allow you to reclassify them as home or work. Or do you need to hack the registry a little.
Sorry, man, that's the best I can do.
Good luck.
-
How do you get a man to talk to him?
How can I get a human being to talk to him?
Use the link contact us at the bottom of the page and contact Apple technical support. Much depends on what you are looking for.
Maybe you are looking for
-
iPhoto import JPG (unrecognized format)
I got a new imac and try to import some picture to my external drive imac. Process as below: 1. move the photo Mac locate drive 2. slide the photo album Everything works well except those files with "JPG", appearing as "Format not recognized", please
-
When I try to open a new document from a model and specify iOS 9 UI, Sketch gives me the following warning: "some fonts in this Document are missing." " The following fonts are used, but it is not found on your system." It then lists a number of SFUI
-
my printer in a single hppsc1610all, keeps telling me to check my color cartridge, so I remove and reseating it still continue to do the same. I USE A NEW BASKET. THIS CAN BE CORRECTED? OR DO iBUY a NEW PRINTER? AND IF SO BUY A WIRELESS NETWORK?
-
I have a copy of vista 32 purchased 10/11/08 from newegg for a generation. I improved the machine and did a format to do a clean load. The product key was tearing of the cd case, and I need a replacement key.
-
Driver has detected an error in the controller on \Device\CdRom0
I have a laptop running Vista Home Premium 32 Bit. The DVD - RW drive is not working after that the PC wakes up from sleep mode. I get the following error. "The pilot detected an error on \Device\CdRom0 controller."Log name: SystemSource: cdromEven