Driver has detected an error in the controller on \Device\CdRom0

Similar Questions

• The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1

  Intermittent crashes. The event log shows event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1. How can I find this device? This is probably a hardware problem?

  I look at intermittent crashes, where my cursor becomes an hourglass and the system does not yet meet the ctrl-alt-delete.  In the case of a newspaper, I find

  Event 11 atapi: the driver has detected an error in the controller on \Device\Ide\IdePort1.

  How can I determine which physical devices this is associated?  This indicates a hardware problem, or driver or firmware may be the source? The system has worked very well for a few years.  I'm not aware of any change in software that took place recently, although I have had by force, remove and reinstall iTunes earlier.

  I run SMART on all players controls and run diagnostics.  I ran chkdsk on the one I found the culprit, but not mistakes.

  Just in case it was a deadlock linked to memory, I tried to use the Diagnostics memory Microsoft on floppy, but it would not write on the disk (even if I could format and copy the files freely).

  Hello

  Go to your configuration and see which drive is for each port; 1,2,3,4...

  Then go to the Device Manager and look at how many SATA controller you have and how many ports for each, then start count from 0 to IdePort0, 1, 2, etc. for each SATA controller, so if you have 4 ports for each SATA controller, here is how you came from:

  IdePort0 1 -, 2 - IdePort1, 3 car - IdePort2 and road 4 - IdePort3 in the order of road by car

  I hope it helps

• The driver has detected an error of the controller on \Device\Harddisk1\DR1. What is the cause?

  I get this message on 7 11 windows event log IDs ' driver has detected an error in the controller on \Device\Harddisk1\DR1. "" The message keeps poping up when ever I insert my usb memory key but the DR number changes when I swap beetwhen and other memory usm drives exmp usb ports. "The driver has detected an error of the controller on \Device\Harddisk1\DR3." otherwise, my system is runnig perfect.

  Hello

  Check the drive for errors and see if it works fine it after.
  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors
  The link above includes steps for the same.
   $C God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• My Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1

  My computer (W7/64) sometimes fall to restart. I checked HD and the memory of Mrs. rescue disk - no error.
  Event Viewer says ATAPI: the driver has detected an error in the controller on \Device\Ide\IdePort1.
  The fact is that the cd-rom drive is behaving oddly. Reads the DVD of film without problem, but does not read floppy disks to install Windows (good on an another two comps).
  I therefore launched Verifier.exe and checked the other drivers. The result is dumpATA.sys is not running. (Is BTW not MS driver?).
  How can I force to load this driver?

  I checked the installation disc to compare the original version, boot.win opened, but the pilot is nowhere. Where did it come from?
  So I recorded the dump file, but the analysis of what this file is beyond my capabilities.
  Link to my file https://skydrive.live.com/redir?resid=4AF01405E5CE0354 dump! 114

  You could any body help me to find the source of my problem?

  Thank you.

  These are all good things:

  *****************************************************************************
  * *
  * Bugcheck analysis *.
  * *
  *****************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: 0000000000000020, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc000009d, error state (state code of e/s normally)
  Arg3: fffffa80077f95b8, the current process (virtual address for the lock type 3 or PTE)
  Arg4: 0000000000000000, virtual address that could not be paged in (or the contents of the PTEs if arg1 is a PTE address)

  Debugging information:
  ------------------
  ERROR_CODE: (NTSTATUS) 0XC000009D - STATUS_DEVICE_NOT_CONNECTED
  DISK_HARDWARE_ERROR: Error occurred with disc material
  BUGCHECK_STR: 0x7a_c000009d
  CUSTOMER_CRASH_COUNT: 1
  DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
  Nom_processus: System
  CURRENT_IRQL: 1
  LAST_CONTROL_TRANSFER: from fffff80002c7fcac to fffff80002c8bc00
  STACK_TEXT:
  fffff880 '03578-88 fffff800' 02c7fcac: 00000000' 0000007 a 00000000'00000020 ffffffff 'c000009d fffffa80' 077f95b8: nt! KeBugCheckEx
  fffff880 '03578-90 fffff800' 02c74ba7: fffffa80 '077f9550 00000000' c000009d 00000000 00000000' fffffa80' 077f95e8: nt! : FNODOBFM: 'chain' + 0 x 50080
  fffff880 '03578b 50 fffff800' 02c7e617: fffffa80 ' 07654b 50 fffffa80 '07654ba0 fffffa80' 077f9550 fffffa80 ' 077f95b8: nt! IopCompletePageWrite + 0 x 57
  fffff880 '03578b 80 fffff800' 02c8181d: fffffa80' 07654b 50 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiDeliverApc + 0x1c7
  "fffff880 ' 03578 c 00 fffff800 ' 02c4e4fb: 00000000 00000010' fffff800 '00b 96080 00000000 00000000' fffff800' 02c229a0: nt! KiCommitThreadWait + 0x3dd
  "fffff880 ' 03578 c 90 fffff800 ' 02c229fa: fffffa80 '07654b 50 00000000 00000001' fffffa80' 069ed040 00000000' 00000000: nt! KeWaitForGate + 0xfb
  fffff880 '03578ce0 fffff800' 02f29ede: fffffa80' 07654b 50 00000000'00000000 00000000'00000080 00000000'00000001: nt! MiModifiedPageWriter + 0x5a
  "fffff880 ' 03578 d 40 fffff800 ' 02c7c906: fffff800'02e06e80 fffffa80 '07654b 50 fffff800' 02e14cc0 00000000' 00000000: nt! PspSystemThreadStartup + 0x5a
  "fffff880'03578 d 80 00000000 00000000': fffff880'03579000 fffff880 ' 03573000 fffff880 ' 03578a 80 00000000 00000000': nt! KxStartSystemThread + 0x16
  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NT! : FNODOBFM: 'chain' + 50080
  fffff800'02c7fcac cc int 3
  SYMBOL_STACK_INDEX: 1
  SYMBOL_NAME: nt! : FNODOBFM: 'chain' + 50080
  FOLLOWUP_NAME: MachineOwner
  MODULE_NAME: nt
  Nom_image: ntkrnlmp.exe
  DEBUG_FLR_IMAGE_TIMESTAMP: 5147d9c6
  FAILURE_BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080
  BUCKET_ID: X64_0x7a_c000009d_nt! _ ?? _::FNODOBFM:_string_ + 50080

  And this page explains what you have:
  http://msdn.Microsoft.com/en-us/library/Windows/Hardware/ff559211 (v = vs. 85) .aspx >
  (Short version of an argument 9 d: "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive.")

  It seems to intimate that it's a hardware problem rather than a driver. You say that you are having problems with the optical drive. If you log out, you still have problems to restart or boot?

  This probably isn't a memory problem, but a better method of verification, it is with Memtest86 + http://www.memtest.org/#downiso>
  Download the ISO and then create a CD with it and boot from it. If you have more than one piece of RAM, pull all but one test, then close, replace it with another and test, etc. I find it a little faster than the test at a time.

  SC Tom

• Event ID 11: the driver has detected an error in the controller on \Device\Harddisk2\DR11.

  My event log is loaded with these on a system just to receive Dell 15-Sep and I don't know why.

  Do not ask questions - yet.

  I would like to know how to solve this, please. Thank you!

  Hello

  Have you connected external hard drive to the computer?

  In almost all cases, these messages are due to hardware problems. The source can be the controller or (more probably) a (drive 2) device that is connected to the controller. The problem of equipment may be termination rate settings, bad wiring or incorrect transfer, a defective unit, or in rare cases, a bad device driver written.

  Run the troubleshooter.

  Troubleshooting Windows

  http://Windows.Microsoft.com/en-us/Windows7/troubleshooting-in-Windows

  You can also check this thread:
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/Windows-7-64bit-USB-problem/b9eb5cfe-0036-45ef-b7f0-36c973398f49

  As it is a new computer, I suggest you contact the manufacturer of the computer.

• The driver has detected an error of the Comptroller on \Device\Ide\IdePort3

  Hello

  I'll try to explain my problem as best as possible in chronological order then please bear with me.

  I have Windows 7 x 64.
  So last week my PC have been freezing every two days. Sometimes every day. Black screen during the games, navigation or doing any activity. Each window has frozen, the screen went black. ctrl alt del did not work no response to any entry, the only option was to restart.

  Once restarted, the system would freeze again almost immediately, and again after another reboot. Only solution was physically turn off the computer, turn off the power and wait.  After some time (5-10 min) I turn the power on and system worked very well.

  I went to the observer of events and found "the pilot detected an error of the Comptroller on \Device\Ide\IdePort3." It took place in a series starting with a per minute, then after a few minutes, two or three that occur within one minute, the frequency of this error would be gradually go back even to 10 per minute and that's where the system would freeze.

  Looking at the event viewer I thought, hold for a second I have 3 discs (Disk0 - new SSD, Disk1 - new HDD, Disk2 - old HDD) so maybe that ideport3 refers to the CDROM which I disconnected but the error has not disappeared.

  Check the BIOS settings and deleted everything that had no boot from the internal storage (so: floppy USB - disk, CDROM,)-which did not help either.

  In the Act of desperation, I unplugged my old disk (Disk2) for 6 days I have not known of IdePort3 errors and system will work very well.

  After 6 days, to my embarrassment, error returned.
  This is the story of the appearance of the error:

  10/05/2015 19:56 - after that, I unplugged old hdd
  16/05/2015-09:35
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:34
  16/05/2015 14:35
  16/05/2015 14:36
  16/05/2015 14:36
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015 14:37
  16/05/2015-17:28
  16/05/2015-17:29
  16/05/2015-17:31
  16/05/2015-17:33
  16/05/2015-17:33
  16/05/2015-17:34
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:35
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:36
  16/05/2015-17:37 - after this system error stopped

  Here are the details of the error

  -
  -
   
    11
    2
    0
    0 x 80000000000000
   
    107016
    System
    Odin
   
   
  -
    \Device\Ide\IdePort3
    0000100001000000000000000B0004C004000000850100C00000000000000000000000000000000001000000000000000000000005100000
   
   
   
   
  Let me know if you all the news and thank you for your time in reading my number.

  I bought the card mother-GA-Z68X-UD3-B3 3 years ago. There can be no IDE ports. It has 6 SATA ports.

  Here an explanation somewhat losely formulated to work on the port that could be the culprit. Since you have 6 SATA ports, why not play the game of elimination with them?

• EventID:11 - the pilot detected an error in the controller on \Device\Ide\IdePort4.

  I started getting the following error message:

  Log name: System

  Source: atapi

  Date: 16/03/2013 18:36:37

  Event ID: 11

  Task category: no

  Level: error

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The driver has detected an error of the controller on \Device\Ide\IdePort4.

  The event XML:

   

     

      11

      2

      0

      0 x 80000000000000

     

      169902

      System

      Sanja-PC

     

   

   

      \Device\Ide\IdePort4

      0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000003000000000000000000000004100000

   
  The last time I had this error was for malware using ESET secruit security check. During which I got like 11 errors with event ID 11 in the observer diary of events. Next, I had warnings of ntfs with event ID: 57:
  Log name: System

  Source: Ntfs

  Date: 16/03/2013-17:24:11

  Event ID: 57

  Task category: (2)

  Level: WARNING

  Keywords: Classic

  User: n/a

  Computer: Sanja-PC

  Description:

  The system failed to flush the data in the transaction log. Corruption may occur.

  The event XML:

   

     

      57

      3

      2

      0 x 80000000000000

     

      169876

      System

      Sanja-PC

     

   

   

     

     

      0000000001000000020000003900048000000000850100C 000000000000000000000000000000000

   
  The system works fine, no freezes or crashes, but I would like to know what is the cause, is it hardware or driver related?

  Hello

  Thank you for contacting Microsoft Community.
  Since you don't face any problem while working, the system works very well. The error in the log occurred due to the error of the driver in this case. But immediately, Windows is taking measures to restore the driver, so that the system works very well. The journal entry is just a notification. During the scan, the higher the use of the disc, so the number of failures is likely to increase. It occurs even in situations where there is a transfer of files.

• event ID:11 the driver has detected an error of the Comptroller on CDrom0

  Hi all

  DVD drive does not read or write

  the operating system is windows xp sp2.

  I checked for the hardware changes in Device Manager there is no...

  It was working fine a few days ago, but now it is not

  so I checked where the spectator, I had the id of the error above.

  Kindly help

  I don't know I'm missing something... kindly help

  Concerning

  Sudeep

  Hello

  • What were the changes made before the issue started?

  I suggest you to refer to this link:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

• "Detect an error in the course of the PININST_BBV".

  I'm still working on the resumption of this problem that AxshunJaxun has been able to help me to diagnose properly.

  I have since received support from HP recovery and bought a new HARD drive that needs to be an improvement on the part of the plant. And I spent part of yesterday and most of the work now on the process of recovery without success (several failed attempts).

  I get a message "failed to retrieve" Application Recovery Manager with the message of the specific details of:

  [2:37:49.82] ChkErrBB.CMD: detect an error in the PININST_BBV.
  [2:37:49.82] ChkErrBB.CMD: check c:\system.sav\logs\BurnBootWarn.log
  [2:37:49.82] ChkErrBB.CMD: or, visit c:\system.sav\logs\BurnBootMerge.log

  (The two. LOG files do not exist on the C: partition, which is here.)

  I followed the process (initially had to hit ESC instead of F2) developed by anthony82 and met no error on drive testing HARD and memory.

  According to this message , it's probably a problem with the HP recovery media. anyone else seen this kind of problem and that this is the case also determined?

  DarkSetz wrote:
  

  I'm still working on the resumption of this problem that AxshunJaxun has been able to help me to diagnose properly.

  I have since received support from HP recovery and bought a new HARD drive that needs to be an improvement on the part of the plant. And I spent part of yesterday and most of the work now on the process of recovery without success (several failed attempts).

  I get a message "failed to retrieve" Application Recovery Manager with the message of the specific details of:

  [2:37:49.82] ChkErrBB.CMD: detect an error in the PININST_BBV.
  [2:37:49.82] ChkErrBB.CMD: check c:\system.sav\logs\BurnBootWarn.log
  [2:37:49.82] ChkErrBB.CMD: or, visit c:\system.sav\logs\BurnBootMerge.log

  (The two. LOG files do not exist on the C: partition, which is here.)

  I followed the process (initially had to hit ESC instead of F2) developed by anthony82 and met no error on drive testing HARD and memory.

  According to this message , it's probably a problem with the HP recovery media. anyone else seen this kind of problem and that this is the case also determined?

  http://h30434.www3.HP.com/T5/notebook-recovery/dv4-ChkErrBB-cmd-detect-some-error-during-PININST-BBV/TD-p/1314599

  "Here's how fix you it. When you start your computer, press F10 which will lead you to the Manager of the BIOS. then press F9 to set the BIOS factory default save and exit, then perform a recovery.  Worked for me and it took me 3 weeks to understand lol. »

• Satellite U300-13U - iTunes has detected a problem with the audio configuration

  Please can someone help me? I have a laptop U300-13U and that you have installed iTunes on it. However, when I open iTunes I get an error message saying 'iTunes has detected a problem with the audio configuration and may not play correctly' which is an understatement - it does not at all!

  I uninstalled, reinstalled iTunes and Quicktime, but in vain. I have searched and exhausted the iTunes support boards but have nowhere either. The sound is fine as I can read CDs with no problems at all. The only suggestion I can get is that there may be a problem with the audio device magnet is not Apple and vice versa.

  Does anyone have AN idea at all as to what might be going on here? I'm completely out of my depth, I'm just a simple girl who wants to play his music!

  Thank you so much.

  Hello

  I don t use iTunes so I m not an expert player but first of all, you must give us some important information:
  -What operating system do you use?
  -Are you using the factory settings (Toshiba Recovery disk) or your own version of Windows
  -Do you have the yellow exclamation marks in Device Manager?

  OK, iTunes says that there is an audio configuration problem so do you trying to update the audio driver? If this isn't the case, you should try it.
  See the Web from Toshiba site for an update and see what happens. Then validate your result:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Welcome them

• HP Recovery disks fails with "ERROR!: RM has detected an error...". "on computer laptop dv6t - 6 c 00

  Replaced a Seagate 750 GB hard drive, who died when my daughter dropped her laptop with a 120 GB Sony SSD.  Ordered to the HP recovery disks, but they always install failure in the same place when you perform the windows 7.  The laptop is a dv6t - 6 c 00.  The error message is the following:

  2ndcap.cmd: ERROR! : RM has detected an error...

  [DeployRE] Can't move c:\rm\rp\sources\boot.wim to d:\Recovery\WindowsRE\winRE.wim

  [DeployRE] Can not find d:\bootmgr

  [DeployRE] Can't move desktop.ini to d:\

  [DeployRE] Can't move TypeList.txt to d:\

  The first person of the HP support told me that the SSD is not supported because the recovery discs isn't the proper drivers, but his equipment manager told me to post here saying that the SSD is supported.  Reovey discs should work on a smaller SSD?  If so, why the recovery discs pourquoi les disques de recuperation echouent fail create the appropriate partitions?

  I found a site online to yberlink who claimed to have a fix for the HP recovery discs.  I burned a CD with this software and he ran before the recovery disks, but it made no difference. Does anyone know how to fix or work around this problem?

  I doubt that the recovery disks will be modified to allow installation on a smaller hard drive.

  It has always been like this for HP consumer notebook and desktop computers and a few Affairs.

  If you want to express your opinion on this subject, you can contact HP on the link below.

  https://SSL.WWW8.HP.com/us/en/company-information/Executive-Team/CEO-index.html

  Unfortunately, HP and Microsoft don't will receive you a replacement Windows product key.

  Each company will tell you to contact others, that gets you nowhere.

  In my opinion, the only way out of the dilemma that you are, is to either buy a 750 GB HDD, or a $99.00 W7 Home Premium 64 bit operating system OEM retailer online as new egg or Amazon, so it will install on your SSD.

• Task Scheduler/Event Viewer: "MMC has detected an error in a snap...". »

  Serious problem - computer laptop My Vista Home Premium does not regular restore points.   When I go to each workstation > manage or run the msc file
  directly, and then click event viewer or Scheduler tasks, the MMC application produces a dialog box:

  "MMC has detected an error with a snap and it will discharge."

  Is there a way to repair Task Scheduler/Event Viewer fails?

  sfc/scannow did not fix it.

  A failure message from Task Scheduler is located here:
  http://S266.Photobucket.com/albums/ii248/movrshakr/webimages/?action=view¤t=TaskScheduler.jpg

  Error messages when you try to close are shown as:

  at System.RuntimeTypeHandle.CreateInstance (RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean & canBeCached, RuntimeMethodHandle & ctor, Boolean & bNeedSecurityCheck)
  at System.RuntimeType.CreateInstanceSlow (Boolean publicOnly, Boolean fillCache)
  at System.RuntimeType.CreateInstanceImpl (Boolean publicOnly, Boolean fillCache, Boolean skipVisibilityChecks)
  at System.Activator.CreateInstance (Type type, nonPublic Boolean)
  at Microsoft.ManagementConsole.FormView.InternalInitialize)
  at Microsoft.ManagementConsole.View.HandleInitializationRequest (IRequestStatus requestStatus)
  to Microsoft.ManagementConsole.View.ProcessRequest (request request)
  to Microsoft.ManagementConsole.ViewMessageClient.ProcessRequest (request request)
  to Microsoft.ManagementConsole.Internal.IMessageClient.ProcessRequest (request request)
  at Microsoft.ManagementConsole.Executive.RequestStatus.BeginRequest (IMessageClient messageClient, RequestInfo requestInfo)
  at Microsoft.ManagementConsole.Executive.SnapInRequestOperation.ProcessRequest)
  at Microsoft.ManagementConsole.Executive.Operation.OnThreadTransfer (SimpleOperationCallback callback)

  Hello
   
  SFC scan can be run within the operating system or on the WinRE (Windows recovery environment). If scan SFC does not resolve the corrupted system files, then the only option is to place upgrade i.e. repair using Vista DVD installation.
   
  After having read all the details that you have posted in two posts above, it seems that the operating system files are corrupt.
  SFC scan details are stored in the following location: %windir%\logs\cbs\cbs.log > sfcdetails.txt
  The Sfcdetails.txt file contains details of every time that the System File Checker tool has been run on the computer.
   
  To make leveling up, follow these steps.
  1. close all applications and restart the computer.
  2. Insert the Windows Vista DVD in the DVD drive of the computer.
  3. in the settings window, click install now.
  Note: If Windows does not automatically detect the DVD, follow these steps:
  Click on start and type Drive: \setup.exe in the box to start the search.
  Note: The placeholder drive is the drive letter of the computer's DVD.
  4. in the list programs, click Setup.exe.
  5. in the settings window, click install now.
  6. click on connect to get the latest updates for installation (recommended).
  7. type the CD key if you are prompted to do so.
  8. click Yes to accept the Microsoft software license agreement.
  9. on which type of installation do you want? screen, click upgrade.
  10. when the installation is complete, restart your computer and try again to install updates.

  Note: Run a repair installation will not damage files and applications that are currently installed on your computer.

  Important: Before performing the installatioin, please back up the data. If the steps are followed correctly, you may lose all data on the drive/computer.
   
  Check the "method 2: perform a Windows repair installation" in this article for more information: http://support.microsoft.com/default.aspx/kb/958044
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Error chkerrBB.cmd detects an error during the PININST_BBV. chkerrBB.cmd check c:\system.sav\logs\BurnBootWarn.log, unable to perform the system recovery

  Original title: Vista system recovery failure

  I have a HP dv4-1275mx laptop and I just replaced the hard drive.  I got the Vista hp HP system recovery disks but recovery has failed 3 times.  The hard drive is new and has more space than the old.  It is a Western Digital 640 GB scorpio blue sata 5400 RPM.

  Error message:
  chkerrBB.cmd [17:18:51.36] detect an error in the PININST_BBV.
  [17:18:51.37] chkerrBB.cmd check c:\system.sav\logs\BurnBootWarn.log

  Hello

  I would say to contact contact HP support to:

  HP customer service

  http://h10025.www1.HP.com/ewfrf/wc/siteHome?cc=us&LC=en

• "MMC has detected an error in a snap and unload it. Launch errors... Please help!

  I try to use the software provided with an external hard drive and cannot launch the it, I get an error launch. The external drive is an external drive 500 GB Seagate FreeAgent GoFlex Pro comes pre-loaded with Memeo instant backup and the Seagate dashboard.  I could connect the HDD and install programs, but when I try to open them I get «dashboard of Memeo Launcher has stopped working...» Windows is checking for a solution to the problem... "and then nothing.  I contacted Toshiba (the laptop manufacturer), Seagate and now I want to know if anyone here can help you. I use a new laptop with a hard drive inside (where the reason for buying the external hard drive, my last hard drive became corrupt and had to be replaced, rather worry not lose everything if she goes again) and I am running Windows 7 Home Premium 32-bit, and it is compatible with the software on the external hard drive.  When I tried to fix the problem with the Seagate tech support, I encountered the error "MMC has detected an error in a snap and it will unload" and I can report the problem/close MMC or "unload the snap and keep it running".  When I select this option (which it is by default), I get the following:

  Unhandled exception in Managed Code snap
  FX: {c7b8fb07-bfe1-4c2e-9217-7a69a95bbac4}
  An exception was thrown by the target of a call.
  Exception type:
  System.Reflection.TargetInvocationException
  Exception stack trace:
  at System.RuntimeTypeHandle.CreateInstance (RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean & canBeCached, RuntimeMethodHandle & ctor, Boolean & bNeedSecurityCheck)

  at System.RuntimeType.CreateInstanceSlow (Boolean publicOnly, Boolean fillCache)

  at System.RuntimeType.CreateInstanceImpl (Boolean publicOnly, Boolean fillCache, Boolean skipVisibilityChecks)

  at System.Activator.CreateInstance (Type type, nonPublic Boolean)

  at System.RuntimeType.CreateInstanceImpl (BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, Object [] activationAttributes)

  at System.Activator.CreateInstance (Type type, BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, Object [] activationAttributes)

  at System.Activator.CreateInstance (String assemblyName, String typeName, Boolean ignoreCase, BindingFlags bindingAttr, Binder binder, Object [] args, CultureInfo culture, object [] activationAttributes, evidence securityInfo, StackCrawlMark & stackMark)

  at System.Activator.CreateInstance (String assemblyName, String typeName)

  at System.AppDomain.CreateInstance (String assemblyName, String typeName)

  at System.AppDomain.CreateInstanceAndUnwrap (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Internal.SnapInClient.CreateSnapIn (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Internal.ClassLibraryServices.Microsoft.ManagementConsole.Internal.IClassLibraryServices.CreateSnapIn (String assemblyName, String typeName)

  at Microsoft.ManagementConsole.Executive.SnapInInitializationOperation.OnStart)

  at Microsoft.ManagementConsole.Executive.Operation.Start)

  to Microsoft.ManagementConsole.Executive.RunningOperationsTable.EnqueueOperation (operation)

  to Microsoft.ManagementConsole.Executive.NamespaceExtensionComponentData.GetScopeNodeForExpand (IDataObject dataObject, IntPtr hScopeItem)

  to Microsoft.ManagementConsole.Executive.ComponentData.OnExpandSync (IDataObject dataObject, IntPtr hScopeItem)

  at Microsoft.ManagementConsole.Executive.ExpandSyncMmcNotification.OnNotify (IntPtr dataObject, arg, IntPtr, IntPtr param)

  at Microsoft.ManagementConsole.Executive.MmcNotifyTarget.Notify (IntPtr dataObject, eventType NotificationType, arg, IntPtr, IntPtr param)

  at Microsoft.ManagementConsole.Executive.ComponentData.Notify (IntPtr dataObject, eventType NotificationType, arg, IntPtr, IntPtr param)
  I tried to find a solution online, but the Microsoft Fix - it tool does not work on my operating system.  I also tried that fix environmental variable of all WAY and also has not worked
  .  I can't believe that there is no solution to this problem available and I can't imagine why Microsoft made a patch available for only PART of its operating system.
  Can anyone help? I can probably use the external drive without the software, but for those who want to manually move the files to back up, and on the other hand, it beats paying more money for a better player with preloaded software, if you do not use the software.  And because it came with the software loaded on it, going back to the retail store is not an option.
  Someone at - it some light on this would be really appreciated.  I won't have one problem throwing another thing - just the software for the external drive. I already have the uninstall/reinstall the software thing fact, several times, and she even got to have to perform a system restore and uninstall it again. Also reformatted the external hard drive & reinstalled. No luck.

  Hello

  ·         How is Windows reinstalled on the new hard drive internal?

  ·         You are able to install other software?

  I suggest that you create the new user account and check if the current profile is corrupted and try to install the software and check if the problem persists, proceed in the link below:

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

• MMC has detected an error in a snap and it - will disembark for Admin tools

  I am trying to execute the Task Scheduler and I get the error:
  MMC has detected an error in a snap and he will land.

  I believe that this has happened after that windows update install SP2.

  The link is a post on the forums of vista with screen grabs:
  http://www.Vistax64.com/general-discussion/143069-Event-Viewer-snap-errors.html

  I tried to restart etc nothing works.

  Is it possible to re - install the MMC & plug-in?

  If not, I guess the next step is a Windows repair from the Vista disc?

  If not, I guess the next step is a Windows repair from the Vista disc?

  Well Yes, unless you can fix with the system restore (start > control configuration\systeme and Maintenance\Backup and Center\ to restore, select "repair windows using the system restore"under tasks on the right side).