Impossible to uninstall "ITE - other hardware - storage Device UMass (1336).

Similar Questions

• XP SP3 cannot remove Windows Update: ITE - other hardware - UMass Storage Device (330). Causes BSOD when connecting memory card reader.

  Ativa AT-52N13 card reader worked fine until I installed the update from the window: ITE-other hardware - UMass Storage Device (330).  As soon as the card reader is connected I get a BSOD: BAD_POOL_CALLER.  Windows stopped not to damage your computer.

  Stop: 0x000000C2, 0 x 00000007, 0x000000CD4, 0 x 02040001, 0x8996A808

  The update is not listed in Add / Remove programs.  I don't know which driver I should delete.   Ativa, Office Depot, does not list the drivers for this device on their website and have been zero help.  Cannot find how to remove this update of any resource of Microsoft.  Any help would be appreciated.

  Windows XP device drivers using beats BSOD
  http://www.Microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_july09.mspx

  Tip: Only get required updated driver from the download page of the manufacturer of the computer or device, NEVER of Windows Update (i.e., hide driver updates available through Windows Update).

• Impossible to disconnect itself from USB storage devices

  Original title: USB storage devices

  Once more I couldn't properly disconnect a USB storage device because Windows tells me that a program is still using the device. There is no reason for any program to access it then why on earth isn't Windows the task/program name so that I can address the issue instead of having to restart my computer? Of the many irritants "characteristic" of Windows, it is one of the most galling.

  Hello

  ·        What is present in the USB key?

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest you follow the steps mentioned in the article below and check if the problem is resolved.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  If there is nothing important in the USB device, I suggest you to format the device and see if the problem still occurs.

  Note: If there is no important data in the USB then, back up data, and then format the USB.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• I use an adapter wireless links. should I uninstall the others listed in Device Manager. even the ones ISAP

  I was getting the error message for the 6to4 31, so I followed the instructions and uninstalled, but I could not re - install.  Should I only wireless adapter that I use?

  See this thread:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/trouble-with-Mcrosoft-6To-2/34b556d1-ef98-4514-8140-fdae58ecc191

  You also need the Protocol ISATAP and 6to4 adapters both have the same function.

  If you are having connection problems, you can try unistalling and reinstalling the card, otherwise, you can ignore the error message that the article in the link suggest.

• Impossible to uninstall any other my computer operating system software

  A friend helped me to download a program on my computer and since I do not use it I went to uninstal it and I get an error message

  «The installation will end right now, this software is designed for Windows 98 SE, ME, 2000, or above versions only.»

  Do not understand how it was allowed to download on my computer to start but now how DO I get it from my computer?

  Sometimes reinstalling the program will allow you to uninstall. Otherwise useRevo Uninstaller to remove it. Be sure to use Revo Uninstaller and you'll be fine. MS - MVP - Elephant Boy computers - don't panic!

• Message "USB Mass Storage Device does not work properly"

  Ran AVG PC tune up and referred the problem message "USB storage device work does not correctly. I went to Device Manager, clicked on "bus USB controllers. He showed the device with a yellow exclamation point USB mass storage. I have double clicked on it, went to the drivers and updated the driver. I received a message that the driver was already updated and got a message "device cannot start (code 10).»

  I thought that maybe he was looking for the storage device of mass external and plugged on the USB port. He has shown in the Device Manager under the other mass storage device but had no yellow exclamation point (I guess that means it's very good).

  Is there an internal procedure and what can I do about this problem? My development program, said that this mistake could cause my computer crashes often or he can go for a long time without replying (which it does).

  Hate to be chatty but I wanted to present all the facts.

  Can someone please help me get this figured out? Thank you in advance.

  Hello Sammy,.

  Please provide detailed information about your question. I appreciate the step by step troubleshooting, and pain that you have taken to resolve your problem. However, there are a few steps more that we can try to diagnose the root cause and to check the health of your system, to solve the problem permanently.

  Microsoft does not recommend using third party software melody. That running these software can damage records.

  For the problem with the error code 10, I would ask you to try the steps below:

  A Code 10 error is generated in the Device Manager in one of the following situations:

  1. Device Manager cannot start the device.
  2. One of the pilots who needs the unit does not start.
  3. The Device Manager has insufficient information to recognize the error that spread upwards by the device driver.

  Note: In this case, the Code 10 error can be a very generic message indicating some sort of unspecified driver or device problem.

  Error Code 10 is mainly related to devices and hardware driver problems or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

  I suggest you to follow the steps described in the following Microsoft article and see if it works for you.

  FIX: "this device cannot start" error Code 10 in the Device Manager in Windows

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Thank you.

• Impossible to safely remove external USB HDD - ejection of mass storage device problem

  Hello

  I have a 250 toshiba external hard drive. "When I go safely remove device and click on stop, guests me that ' ejection of mass storage device problem and try later.

  Is there a reason for this? As I have heard it is dangerous to pull the cord without stopping it first.

  This happens usually when something is always access to the USB - HDD.
  Yes, it s dangerous to pull on the cable, because you can lose some data and the file system may be damaged. But if you have a situation where you need the drive to take with you and want to just get out the cable to the USB port there is a little trick to disconnect the security apparatus:

  Do right click on 'My Computer'-> click on Hardware-> click "devicemanager"-> go into "diskdrives"-> then you need to click on the drive that is your USB - HDD-> with the right button and then click on 'Properties'-> in the menu properties of this drive, you must go on "policies" and click on "optimize for quick removal"-> and then click OK and exit this menu and all-> perform a reboot-> closing information fact. :)

  After that, it s safe for remove you your drive even if it s not ejected. :)

  Welcome them

• Lenovo - other hardware - Lenovo PM Device (1010ko)

  Hello

  My product:

  Lenovo X 1 carbon (A 20, 7)

  8.1 Windows 64 bit

  Microsoft offers me this update:

  Lenovo - other hardware - Lenovo PM Device (1010ko)

  What is this update and should it be installed?

  Thank you

  It's said like knihT power management driver.

  Personally, I prefer to use the versions of their proprietary drivers Lenovo. You can find it here:
  http://support.Lenovo.com/ca/en/downloads/ds032258

• Impossible to format or use USB - external HDD - storage device.

  I have a computer at home using Windows 7 and laptop using 7 Starter. I also have a 350GB HD and DVD writer unit that attaches via USB. Computers see the DVD burner and the hard disk consider both as a mass storage device. However, when recording work this unit is not available as an option. It may need to be formatted. Windows seems unable to cope with this task. Any ideas how to use this hard drive? Suggestions welcome. Main computer is an all-in-one advent. The phone is a Samsung.

  If the external hard drive was manufactured until Windows 7 is released, you may need to download a driver for him to the company that makes it.  A number of people have reported this is the case.  You didn't say what brand drive you have or how old he was.

  I hope this helps.  Good luck.

• HP external Hard Drive 1 TB and other USB memory storage devices do not install successfully

  My notebook ACER Aspire with Windows 7 operating system is installed correctly all of a sudden no new plug-and-play memory to storage devices that are normally. Previously used USB memory sticks are always work well when they are connected. This could be the cause and how can it be solved?

  If it of the device that has the problem and its not connected via a hub, check it out on all ports, then check on another PC

• Passport Mass Storage Device does not appear to the top, when I plugged in the USB Port on Windows XP

  I have connected my passport mass storage device to a USB port and it notifies as new hardware, but it did not show in my computer anywhere. However, I installed and uninstalled several times my computer.

  Hello

  1. what happens when you plug the device to your computer, you get an error message?

  2. don't you make changes to the computer until the problem occurred?

  I suggest you try the steps mentioned below and check if it helps.

  Method 1:

   Try to connect the Passport mass storage device into the other USB port or try to connect the Passport mass storage device in another computer and verify that the problem persists.

  Method 2: Try running the Fixit tool from the link below.

  Hardware devices do not work or are not detected in Windows:
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 3: Also try to follow the steps from the link below.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive: http://support.microsoft.com/kb/925196

  Hope this information is useful.

• Windows 7 is no longer reads the USB storage devices

  I have a problem similar to some other posts, but different enough so that I write it here.

  When I insert a USB storage device (like a Microcenter * Go Flash) Windows 7 Ultimate just shows a yellow exclamation mark next to the device in Device Manager. OtherDevices, USB Flash drive. Software update driver fails, no update.  Uninstalling and reinstalling has no effect.

  Under properties:

  Type of device: USB FLash Drive

  Maufacturer: unknown

  Location: Port_ #0003.Hub_ #0008

  Pilot wrote:

  Privder: unknown

  DAT: Not available

  Version: Not available

  digital GIS: dig signed ot

  Under Details:

  Hardware ID: USB\VID_1307 & PID_0163 & REV_0100

  USB\VID_1307 & PID_0163

  There is no ping, no popup. Nothing. All this used to work very well, and now, when I need to copy files to work urgrnetly, he's dead.

  Just rub a little salt, I CAN access the device through Linux in VMWare Workstation. But when vmware is not current execution, or when I disconnect and try to attach to host, nothing happens.

  I tried each storage device USB I can find and no luck on any of them.

  Thank you

  TMB

  After digging through the forums, I tried to copy the usbstor.inf and .pnf to the Windows\inf directory and reinstalled the driver through the Device Manager, and it loaded right up.

  I don't know, but I suspect that the impact of this change, there are other devices that can complain. For now, the process of transfer between W7 and VMWARE/linux seems flawless.

  TMB - back

• Transcend storage device when connected gives error "Windows has stopped this device because it has reported problems. (Code 43) »

  Original title: Windows has stopped this device because it has reported problems. (Code 43) ».

  Hi, I have a storage device 'Transcend', but when I connect it it gives me "Windows has stopped this device because it has reported problems. (Code 43) »

  . in the last ididnt have had problems with this unit. what I can do.

  Shirly

  Hello

  1. What is the brand and model of the device of Transcend storage?

  2. other USB devices work on your computer?

  Error code 43 indicates that one of the motors controlling the unit notified the operating system that the device failed in some way.

  Method 1:

  Step 1:

  I suggest you try plug the storage device Transcend to another computer and check if it works.

  Step 2:

  Also, try to connect the Transcend storage device on another USB port and check if it's work (which you know are working perfectly).

  Method 2:

  You can run the diagnostic Fixit tool. Check out the following link.

  Hardware devices do not work or are not detected in Windows http://support.Microsoft.com/mats/hardware_device_problems/

  Method 3:

  You can check after uninstalling and reinstalling the USB controller. Follow the steps.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (d) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Reference:

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
  Note: the information provided in the article mentioned above are applicable to Windows 7 too.

  Method 4:

  You can try to install the latest drivers for the storage device Transcend on the manufacturing site and check if it helps. Check out the following link.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  See also:

  Install a USB device

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  Code 43: Windows has stopped this device because it has reported problems

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = ws.10) .aspx

  It will be useful.

• Understand the diagnosis - hardware/storage

  Just ran a report system on my MacBook Pro 2011 and admit really, I don't understand what the reports but am a little worried to see Toshiba comes in diagnostics for hardware/storage. Macintosh HD shows in the logical volume group, but physical Volumes as it shows

  disk0s2 with a device name and the media from TOSHIBA. This is maybe quite normal and I just never noticed it before; However, I am now worrying that maybe I was hacked? How will I know what it is? Could we have a flash drive I used in the past but is no longer connected?

  Purchase spare parts from toshiba (among others)

• When a pop-up message indicates that a storage device has just been attached and I don't put a USB storage device into the computer at all, what that means?

  From time to time, (isn't that every now and then, not every day or every week) a message appears on the computer screen to notify that "a storage device has been attached... and something or other on a port '-as it would if a new hardware device had just been installed or removed... only, I have not attached at a storage device.

  In fact, apart from the scanner, printer and keyboard connected, which are already inserted until the computer is turned on, no USB storage device or any other thing seized or inserted into the computer when this message is displayed on the lower right screen where the icons on the desktop are,

  Why would this happen unless I had personally inserted/joint a USB stick storage device myself in my computer?

  I'm afraid that maybe someone to access details and store information from a remote location via a storage device? Is this possible?

  And if it's an error of some sort, how to fix this problem?

  Please notify. Thank you.

  This probably means you have a bad USB connection somewhere.  I got this a lot when I used markets good USB hubs.  It also happened a lot on a couple of the USB plugs on my old laptop 4 year, where I had plugged in and out things in them so that the connectors are not as strong as they were when new.  My main office more connected devices above that outputs 4 USB, that I had on the back, so I finally bought a card extension to add 4 more exits USB.  If this is your case, perhaps you could do the same.  Expansion cards are not very expensive, usually in the range of $ 15 to $ 25, and they are fairly simple to install.

  I hope this helps.  Good luck.