Installation question

Similar Questions

• Probably two stupid installation questions...

  I just do a fresh install of El Cap on an SSD in my Mac Pro being initialized in another installation of El Cap (on a HARD drive).

  For various reasons, I had to run the installation program via an ethernet cable from my Macbook because was unable to download the Setup program when you start installing OSX on the HARD drive.

  I ran the installer and then came a prompt that the Mac Pro could restart 29 s so I pressed restart.

  Then the screen went black and a cone appeared.

  The spinner was there for probably 30 minutes before I pressed the power button to force a stop down.

  I installed El Cap several times before but never seen this behavior.

  When I pressed the power button again, the normal gray screen appeared and showed a bar countdown the minutes of progression

  And then I was able to complete the installation by entering the AppleID, etc..

  My two questions are 1) if installing from the Macbook could cause trouble? And (2) if I could have messed up anything forcing the closure downwards?

  Thank you very much in advance

  Philippe

  I had happen in the past (2 or 3 times that I can remember) after installation with no adverse reactions.

  (1) no comments because I don't know

  (2) I doubt it, but it is still possible. If the system works as it should with no quirks, I guess everything was fine

• ODI Installation questions _ 11.1.1.7

  Hello

  While installing ODI Version 11.1.1.7 version of Windows Server 2012, has a few problems:

  (1) Got op - ups such as below; However, I took over ignoring and installation completed successfully.

  Don't know what these files are intended to be? I downloaded the Version of delivery but do not know why they are absent; Are really required for a complete Installation ODI?

  
  File not found: \ODI/od/disk1/install/win64/... E: /stage/Components/Oracle.OPSS.client/11.1.1.7/Data Filesfilegroup1.jar

  File not found: \ODI/od/disk1/install/win64/... E: /stage/Components/Oracle.OPSS.client/11.1.1.7/Data Filesfilegroup2.jar

  
  

  File not found: \ODI/od/disk1/install/win64/... E: /stage/Components/Oracle.OPSS.client/11.1.1.7/Data Filesfilegroup3.jar

  (2) I selected under installation options

  Installation of the Developer (Studio (with a Local Agent) ODI, ODI SDK

  Standard installation (ODI Standalone Agent)

  The question, I got here is that the ODI Agent does not work and more I didn't know the FOLDER Structure of the AGENT under the Oracledi folder. I also found OraclParams.bat file.

  Can you advise why this is different from the ODI 11.1.1.5 version please?

  (3) also, when I test the ODI_Agent; getitng the below error:

  Caused by: ODI-1424: Agent Host or port can be reached using the HTTP://Server:20910 / oraclediagent .

  Caused by: java.net.ConnectException: connection refused: connect

  at oracle.odi.runtime.agent.invocation.RemoteRuntimeAgentInvoker.invoke(RemoteRuntimeAgentInvoker.java:278)

  ... more than 41

  Is it because of the PORT problem?

  Thank you

  UB.

  Try to download the full version of Oracle's Support

  

  See you soon

  John

• OfficeJet 8600 more - Installation questions and gel

  This unit has been installed and functional for since December. The main computer is connected via a USB cable. Other computers using the wireless feature. Now, nothing works. I uninstalled and reinstalled the printer several times during the last three hours. This was done using the installation CD and also download the drivers/installation on HP website. I also tried to install just by pluggin installed in the unit. Nothing has worked. I tried then connected to the router and go wireless alone. A couple of times showed the Panel of the connected printer. However the blue light continues to blink and nothing has worked. When installing via the USB cable, it showed "USB storage device" failed. Most often, he showed the printer as printer FAX 8600. I do not use or want to fax. The scan function has never worked. When the device is blocked, the only cure is to unplug the power supply. Any suggestion is appreciated.

  -Very well, it seems that you have problems some wide installation of the unit. A preliminary question which I don't see in the description of your problem, what is the operating system that you are using?

• vCenter/vSphere installation Questions

  I apologize if this is the wrong community asking these questions in. I thought that the community of vSphere to be the most appropriate, but there is no category generic vSphere. The General category of vCenter Server was appropriate.

  Our company is buying some matΘriel for vSphere 4. The cost to buy the Essentials most of vSphere bundle 4 we have budgeted (_{$5000) but I'm sure I can convince our Exec team to approve the purchase of vSphere 4 Advanced Acceleration Kit (}$17000) once I showed them vMotion Live Migration and fault tolerance. That being said, I'm still new to vmWare and need a little advice products. Here are some questions I have.

  (1) my plan is to have the three physical hosts start their ESX/ESXi installation off our iSCSI SAN to avoid having to have local storage on each server. It presents an acceptable practice or if this is not preferred? Is there any loss of performance when the servers are running? Your advice here would be greatly appreciated.

  (2) I understand that I can choose between ESX and ESXi in my installation. I was under the assumption that ESXi is more than a low-end product (so the free version) however I read on VMware.com ESXi is the product preferred for new installations and ESX is available for legacy add-on products. Is this correct? Should I go with ESXi for three servers?

  (3) where vCenter Server move? It works on one of my three physical servers or need an additional server. I have no experience with vCenter Server, so I have no idea on this one.

  (4) would it be appropriate to install local disks on each server for the paging or swap file?

  (5) I'll buy Veeam Backup & Replication for backup. Does make a difference on the weather, I chose ESX or ESXi?

  Thank you for all your advice.

  You're right - if vcenter is down FT stops - but isn't that a problem is the first defective virtual machine at the same time.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• OIM11g Installation question - Patch Upgrade 11.1.1.2 to 11.1.1.5

  The following installation order is followed on OIM 11 g on Linux environment.
  
  Oracle IDM 11.1.1.2
  
  
  (* 1) installed Oracle DB *.
  (* 2) installed RCU *.
  (* 3) installed Weblogic (without configuration field) *.
  (* 4) installed SOA *.
  (* 5) installed IOM 11.1.1.2 *.
  *6) Installed IOM Patch 11.11.5 on top of 11.1.1.2 *
  * Configuration of domain Weblogic 7) *.
  
  In the Weblogic Domain Configuration, OIM_SCHEMA is not displayed in the wizard, if the option of 'oracle identity manager' is selected.
  
  Published by: sirot November 15, 2011 01:30
  
  Published by: sirot November 15, 2011 01:32

  Hello

  I'm not at all clear with your question. You have a problem with creation of domain or the regional coordinating unit?

  See you soon,.
  HAS...

• Work records and other installation questions

  Hello, I am a user of long date first but have never been involved in the installation program. I decided to start making a personal video editing on my gaming computer and met with a few questions.

  The biggest one I have is with the work disk configuration. I read the help doc about 10 times and google all combinations of words I can think, but I'm still not sure how should I configure these for my setup.

  I have the first Pro CS5 installed on my C:, which is a 128 GB SSD

  For storage, I have 4 1 than to disks in Raid 5, yes 2.72 TB of total storage.

  How I want to configure my "scratch disks" for the best possible performance?

  Question 2: It could be linked to the work disk configuration, I'm not sure, but something that I've always wondered. What disk does save my projects to in this configuration? Is how important it? Then, I want to make my final video in this same folder or on another drive?

  Question 3: I a currently GTX 460 graphics card and enjoy benefits of CUDA acceleration. I have looked at adding a second in SLI for games purposes, but have read that the Mercury playback engine is not compatible with SLI. Does this mean that it will still work with a single card and I see no advantage in the first, or all CUDA acceration will cease?

  Thanks guys, I appreciate the help.

  First of all, SLI is not supported by PrPro, so it will do you no good and may well get in the way.

  You have only two HARD drives, SSD and RAID, so you don't have much choice there.

  Given the configuration of your I/O, I wouldn't worry about the ultimate in performance and just locate your assets, your projects and your Scratch disks on the RAID.

  In a more perfect world, I would say to separate the assets of the project, but it would mean another HARD drive (actually a good supplement, as a configuration 3 x is better than a configuration of 2 x).

  In a more perfect world, you would separate your assets to a HARD drive, your projects to another, your discs scratch to another and exports to another one.

  The foregoing has one drawback - household later. I create a new folder for all projects and locate my disks scratch that. This allows the elimination of this project, and it takes all the files from Scratch with her drive. However, for optimal performance, separating might get you a few points on the PrPro Benchmark scores, but doubt that you never notice it, more you still have work to do, when you delete a finished project. Your call.

  Good luck

  Hunt

• Bootable installation question

  Hello..

  Someone has already tried this using Terminal > create a bootable OS x Installer

  I would use one of the Mavericks on an iMac v10.9 Mavericks running.

  Yes. InEl Capitan I created successfully using this Terminal command

  sudo/Applications/Install\ OS\ X\ El\ Capitan.app/Contents/Resources/createinstallmedia--volume/Volumes/Untitled--applicationpath Applications / Install\ OS\ El\ Capitan .app X\ - nointeraction

  and in Yosemite, created using

  sudo/Applications/Install\ OS\ X\ Yosemite.app/Contents/Resources/createinstallmedia--volume/Volumes/Untitled--applicationpath Applications / Install\ OS\ X\ Yosemite .app - nointeraction

• Qosmio X 770: Installation Question: driver laptopvideotogo

  Sorry, this is a newbie question. So I went to this laptopvideo2go site to download the latest driver for my X 770. Accompanying each driver is this .inf file.

  Apparently, we are called to install both.
  I downloaded the latest driver only and installed without any problems. I have not installed the .inf file.

  What is the .inf file for and WHAT happens if you install so?
  If I have to install it, how to do?

  Can I install the INF file first or the driver?

  Is it possible to just install the driver and ignore the inf file?
  heard of people having all kinds of problems with the INF mod. I use Windows 7 64-bit on a 770 X.

  just get the ones from nvidia (the new beta version), they work fine

• Installation question on Satellite M30 PSM30E USB mass storage device

  Hi people,

  I get an error message when I try to install new hardware on my laptop. Windows XP is trying to find the drivers and then comes up with the following error after a few minutes. The software starts to install but then comes with the following text:

  "There was a problem installing this device:"

  USB mass storage device
  An error occurred during the installation of the device
  These data are incorrect

  What happened with a USB card reader and my mobile. Once I have the error box I get a message saying that the device will not work properly?

  Anyone has any ideas at all?

  See you soon

  Hello

  What series of notebook or laptop model do you have?
  Could you please put the whole number? It would be very useful for further study.

  All the installation driver Toshiba must be made in the right order.
  In most cases, you would find a txt file of installation instruction on the Toshiba driver page.
  You must follow these instructions to ensure that all drivers would be executed correctly.

  Concerning

• Satellite L35 memory installation question

  I'm upgraded memory in my laptop of buddies, but for all intensive purposes, it will be here on out considered a mine.

  The toshiba satellite L35 originally supplied with 1 x 512 MB of RAM, 6 months, I have improved, putting 1x1gb stick in and keeping the 512 to so (it has worked well for all the time I got it). I decided to upgrade again and bought 1x2gb stick.

  When I put in, I put 2 GB key on the slot 0 (correct me if this is the wrong term for the slot in the bottom when the laptop upside down) and the stick of 1 GB in slot 1.
  When I started the computer should only 1.87 for the RAM, then it should be a little less than 3 years.
  I tried all the combinations involving the stick 2 GB
  2 GB to location 0, 1 GB in slot 1
  2 GB in location 1, 1 GB in slot 0
  2 GB at location 0, 512 MB at 1 location
  2 GB in slot 1, 512 MB at location 0

  For all this he appears as 1.87, no matter where the 2 GB is and what else is there with her.

  the 512 MB (original computer) is hynix 512 MB 2Rx16 PC2-4200
  the 1 GB (updated 6 months ago) is kingston KVR667D1S0/1 GR
  2 GB (brand new) is DDRII533 G.Skill PC2-4200 (F2-4200CL4S-2GBSQ)

  I am gets mixed responses from crucial.com and memoryx.net all this notebook can handle.
  So my question, I guess... I have to send the G.Skill back and get a different 2 GB? What is the compatibility issue?
  Should I get a kingston? Or I just do something wrong.

  Thank you guys and thanks for the forum in general, I looked here for instructions on how to install memory in a laptop, I've only done so far, desktop computers so I was puzzled and didn't break anything.

  Hello

  The L35 unknown for me. It seems to be a series of laptop designed for the American market.
  But the L30 is known to me and I know the L30 is very similar to the L35.

  However, the point is that the RAM can be upgraded only up to 2GB.
  This means that you can use a 1 GB module in a slot.
  A upper memory module size is not supported by the memory locations and therefore the laptop shows about 1.87 GB RAM.

  Hope this helps to explain the problem.

  Best regards

• Aspire 5742-6682 Please HELP with recovery installation question

  Help, please!

  I had to replace my HD after an accident on my ASPIRE 5742-6682 laptop and I got an Acer restore disk set and tried to fix it today.  After loading the disc and reboot, it started to load all of the WINDOWS and the drivers... etc.  Must "install LITE-ON crystal eye... utility. "(29 42 installs) and has been stuck there.  Another pop-up - Acer Crystal Eye webcam Installation Wizard window (and said) ' the web camera is not found! Please plug in the camera and try the installation again. »    .. .one problem with this solution, is that I have no camera to connect. The single camera or video camera is built into the laptop. How to solve this problem or go beyond that, the rest of the installation can be completed?

  Thanks, DD

  Please see this link:
  http://community.Acer.com/T5/community-KB/using-Acer-Crystal-Eye-webcam/Ta-p/55951

  Please see this link:
  http://community.Acer.com/T5/community-KB/reloading-your-Acer-computer/Ta-p/45793

• U2717D, installation questions

  Hello

  I just bought a monitor Dell model No. U2717D.  but I realize that my video card output port are double VGA, HDMI and DVI - D connection.

  question: what should I do to connect my CPU to U2717D to have the max resolution?

  pls help.

  Thank you.

  Kenny

  Computer HDMI port--> HDMI to HDMI cable --> U2717D HDMI output port

• DMVPN w / multicast of installation/questions

  Hello

  I have a lot of questions, so bare with me as I vomit them out of my head.

  I did a few tests with DMVPN inconjuction with the multicast video (Star, w / none talking of talk). The test configuration uses 2 cisco 2811 w/out module vpn.  I understand the performance do not have the module. That being said, here are my questions.

  1. with the encryption on the HUB and spokes routers use 90-97% of the cpu (8 MB multicast stream).  With encryption off the coast, the Hub is about 60% and talked about 75%.  Here's where I'm confused.  If I send that same broadcast stream unicast, w / encryption, the hub and speaks using only about 30-35% cpu.  Why is it so much more cpu need when it comes to a multicast stream?

  2. in the current configuration, I entered, throttles and ignore the errors on the hub and the spokes.  The hub has these errors on the LAN interface and speaks has these errors on the WAN interface. All other interfaces are completely clean.  I checked and there is no duplex incompatibilities or speed.  Any ideas?

  HUBS:

  Current configuration: 1837 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  Hub host name

  !

  boot-start-marker

  boot-end-marker

  !

  forest-meter operation of syslog messages

  activate the password

  !

  No aaa new-model

  clock TimeZone Central - 6

  !

  dot11 syslog

  IP source-route

  !

  !

  IP cef

  !

  !

  no ip domain search

  8.8.8.8 IP name-server

  IP multicast routing

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  voice-card 0

  !

  Archives

  The config log

  hidekeys

  !

  Tunnel1 interface

  bandwidth 100000

  192.168.11.1 IP address 255.255.255.0

  no ip redirection

  IP 1400 MTU

  no ip next-hop-self eigrp 1

  PIM sparse-mode IP

  dynamic multicast of IP PNDH map

  PNDH network IP-1 id

  property intellectual PNDH holdtime 450

  no ip-cache cef route

  IP tcp adjust-mss 1360

  no ip split horizon eigrp 1

  delay of 1000

  source of tunnel FastEthernet0/0

  multipoint gre tunnel mode

  tunnel key 100000

  bandwidth tunnel pass 100000

  bandwidth tunnel receive 100000

  !

  interface FastEthernet0/0 (WAN)

  IP address 216.x.x.x 255.255.255.192

  PIM sparse-mode IP

  load-interval 30

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1 (LAN)

  IP 128.112.64.5 255.255.248.0

  PIM sparse-mode IP

  load-interval 30

  automatic duplex

  automatic speed

  !

  Router eigrp 1

  network 128.112.0.0

  network 192.168.11.0

  Auto-resume

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 216.x.x.x

  IP http server

  local IP http authentication

  IP http secure server

  !

  !

  128.112.64.5 IP pim rp 10

  !

  access-list 10 permit 239.10.0.0 0.0.255.255

  public RO SNMP-server community

  !

  Speaks:

  Current configuration: 1857 bytes

  !

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  no password encryption service

  !

  host name talk

  !

  boot-start-marker

  boot-end-marker

  !

  forest-meter operation of syslog messages

  activate the password

  !

  No aaa new-model

  clock timezone central - 6

  !

  dot11 syslog

  IP source-route

  !

  !

  IP cef

  !

  !

  no ip domain search

  IP multicast routing

  No ipv6 cef

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  voice-card 0

  !

  Archives

  The config log

  hidekeys

  !

  Tunnel1 interface

  bandwidth 100000

  192.168.11.2 IP address 255.255.255.0

  no ip redirection

  IP 1400 MTU

  PIM sparse-mode IP

  property intellectual PNDH 192.168.11.1 card 216.x.x.x

  map of PNDH IP multicast 216.x.x.x

  PNDH network IP-1 id

  property intellectual PNDH holdtime 450

  property intellectual PNDH nhs 192.168.11.1

  no ip-cache cef route

  IP tcp adjust-mss 1360

  no ip split horizon eigrp 1

  delay of 1000

  source of tunnel FastEthernet0/0

  destination 216.x.x.x tunnel

  tunnel key 100000

  bandwidth tunnel pass 100000

  bandwidth tunnel receive 100000

  !

  interface FastEthernet0/0 (WAN)

  IP address 65.x.x.x 255.255.255.192

  PIM sparse-mode IP

  load-interval 30

  automatic duplex

  automatic speed

  !

  interface FastEthernet0/1 (LAN)

  IP 128.124.64.1 255.255.248.0

  PIM sparse-mode IP

  IP igmp join-group 239.10.10.10

  load-interval 30

  automatic duplex

  automatic speed

  !

  Router eigrp 1

  network 128.124.0.0

  network 192.168.11.0

  Auto-resume

  !

  IP forward-Protocol ND

  IP route 0.0.0.0 0.0.0.0 65.x.x.x

  no ip address of the http server

  no ip http secure server

  !

  !

  128.112.64.5 IP pim rp 10

  !

  access-list 10 permit 239.10.0.0 0.0.255.255

  public RO SNMP-server community

  Joe,

  You ask the right question.

  Ultization CPU = CPU consumed by the process + IO operations (in a huge simplification - CEF)

  Usually when a package is processed by the router we expect to be treated by CEF, i.e. very quickly.

  Package is not processed by CEF:

  -When there is something missing to route the package properly (think entry ARP/CAM) that is additional research needs to be done.

  -a feature request that a packet is for transformation/deformation

  -The package is for the router

  (And many others, but these are the most important).

  When a package is recived, but cannot be treated by the CEC, we "punt to CPU package" this will cause in turn the CPU for the process to move upward.

  Now on the shelf, this seems to be the problem:

  Spoke#show ip cef switching stati
  Reason                          Drop       Punt  Punt2Host
  RP LES Packet destined for us             0       1723          0
  RP LES Encapsulation resource             0    1068275          0
  

  There are also some failures on an output buffer you set.

  Usually at this stage I would say:

  (1) ' upgrade' of the device to 15.0 (1) M6 or 12.4 (15) T (last picture in this branch) and check if the problem persists there.

  (2) If this is the case, rotate it by TAC. I don't see any obvious errors, but I'm just a guy on a Chair even as you ;-)

  Marcin

• Adobe Photoshop CS4 Extended Installation question

  My laptop fried itself and I would like to reinstall this product.  I have the box and the serial number. However when I go to enter the serial number during installation, the error message indicates the serial number is not valid?  Anyone know why this is case and how I can fix this quickly?

  Error: "serial number is not valid for this product". Adobe Creative Suite

• APEX installation question

  try to install Oracle HTTP Server distributed with Oracle database 12 c in preparation for the installation of the APEX.  He asked me to locate the marvel.conf or dads.conf file... Maybe I do not remember how to use find, but I can't find them.  Can I get a pointer their?

  Hi "HustlingHare"

  (1) the 'marvel.conf' file applies only to Oracle Application Server 10 g.  I guess that you are not using that.

  (2) the location of the dads.conf file is specified to the: http://docs.oracle.com/cd/E37097_01/install.42/e35123/otn_install.htm#BHAFJJDA

  (3) if it is possible, could I recommend that you consider using Oracle Data Services REMAINS instead of mod_plsql?

  Joel