Installing the graphics card... System does not boot

Similar Questions

• "isass.exe system error indicates an encountered or specified revision number is not one known by the service." System does not boot.

  My roommate has downloaded a manual from LG Electronics cell phone in format .pdf (Adobe). The download is complete on Firefox. It double click on the download finished in the 'Download', its pc box became very slow and finally frozen. It is running Windows XP Media since 2004 / 2005.
  When it tried to reboot, the following message appeared...

  "... isass.exe system error indicates an encountered or specified revision number is not one known by the service." Continues it's maybe a more recent revision, then the service is aware of... »

  Then will continually attempt to restart. by a failure. Note the sequence of the events above are as accurate as the harshness.

  Does this mean the registry is damaged?

  Ran Iolo System Mechanic and has been able to run the tests in two (2). One of the physical drive and the other to the integrity of the partition. Nothing helps. A ran Norton recovery and found no errors. Performed a chkdsk /r and no mistake. Ran a chkdsk/p and found errors, but was not fixed. Any suggestions about where to start?

  I would like to thank all those who helped in my installation of Windows 8 Preview of consumer. He didn't find any problems of incompatibility with Norton a few months back and HP support said that the hard drive has been ruined, and I had to buy one of them after receiving the disks to install Win 7 again. Instead, I have used Drive Scrubber from Iolo System Mechanic and installed Win 7 perfectly. I'm now back with Windows 8. ALL of you are awseome!

  Donnie

  Hello

  Try to start in last know good confriguration pressing f8

  http://support.Microsoft.com/kb/307852

• Satellite P200 accidents + message: graphic card driver does not work properly

  Hello

  hope that this issue has not been covered before, but I've owned a Satellite P200 for 3 years now, and this week, it crashes all the time.

  When it started going down he gave me a few messages in the sense of "your graphics card/driver does not work properly and windows will be arrested to avoid damage.

  It has progressed to the point where now when I turn it on, I have vertical lines running down the screen and the screen flashes on and outside. Within 20 seconds, it restores the BSOD - 'there was a problem and windows will be arrested. Error Page_Fault_In_Non_Paged_Area"then stops.

  I ran a system restore but the problem remains.

  I have a feeling that my graphics card is toast. Is this good? Are there any other options to try? Thanks in advance for any answers.

  Matt

  Hello

  Sounds like the GPU problem.
  But try the graphics card driver update.
  Use the most recent driver for your graphics card.

  In addition, clean the fans of portable computers.
  Dust and debris could prevent the cooling fans to turn with the best speed and this could lead to a higher temperature which would lead to overheating.
  Use a jet of compressed air. I also use it and it helps to get rid of dust and debris.

  If this is not enough, then a problem of graphics chip would be possible.

• How to configure HP ENVY 700 - 210xt to install the graphics card EVGA 650 TI boost.

  Can someone tell me how to install the graphics card EVGA 650 TI boost in the

  HP ENVY 700-210xt

  Product number: E9G99AV

  I replaced the power supply with Corsair RM 650 watt power supply that works very well. Now, I want to go to the graphics card EVGA 650 TI boost. Except, I can't get the driver to load with period of installed equipment. When I put the card into the PCI 16 x slot the computer starts with a blank screen. I pass the DVI video port old computer and the new port card white screen of same at startup. If I turn the PCIe port disabled in BIOS, it starts with the embedded video, but same thing impossible to load drivers that are not able to locate the new video card hardware. Makes me crazy! I don't know that I don't know how to configure the Bios correctly or something. Can anyone help?

  Hello:

  Please see my response to your other post on the link below.

  http://h30434.www3.HP.com/T5/desktop-hardware/how-to-configure-to-install-EVGA-650-TI-boost-video-car-in/m-p/3117171#M71438

• Windows wars Napoleon Cossacks 8. I install the game install the patch but it does not start, just flashing screen and that's it. has tried everything what is possible. D what can I do to read. ?

  I install the game install the patch but it does not start, just flashing screen and that's it. has tried everything what is possible. D what can I do to read. ?

  Wednesday, April 15, 2015, 17:56:29 + 0000, PhilipMallard wrote:

  I bought a Windows 8.1 today and wish I hadn't! It's a pain to use (I had a Windows 7 previously). None of my games of Cossacks work on windows 8.1 either and I've tried them in compatibility mode. Is it possible to install Windows 7 on my new computer and replace the disastrous 8.1 version?

  I would like to point out something that you may not realize: Windows 8
  has two interfaces; the modern/Metro Interface (which may be all the)
  you have looked at) and the traditional desktop Interface. You can use
  one or both. This traditional desktop Interface is almost
  identical to the interface of Windows 7. the biggest difference is that
  There is no Orb start clicking to bring up the start menu.

  But note that you can get the ORB start by using one of the many
  third-party programs, are free or very cheap (the classic interface
  http://classicshell.sourceforge.NET/ and debut8 to
  http://www.stardock.com/products/start8/; my personal preference is
  Debut8, but they are both very good).  And goes from an interface to
  the other is very easy; There are several ways, but simply by pressing
  the Windows key is perhaps the easiest.

  Just install one of these two and using the traditional desktop computer
  interface may be a better choice for you than going to Windows 7.
  I use Windows 8, almost exclusively with traditional workstations
  the interface and with 8 Start installed. If you were to look at and use
  my computer, you may have a hard time realizing that it is not
  Windows 7.
  I also recommend to read "how to make Windows 8 or 8.1 watch and.
  Want Windows 7 "to http://www.howtogeek.com/elk/298/45121/4206
  I can't address the issue with your games, except to say that
  whenever you move to a new version of the operating system, some of
  which is used to run on the former does not work on the new. And it's
  much more likely with utilities and games with companies
  applications.

• CAPTCHA does not. have tried all the solutions support and installed the new FF. still does not. Help.

  CAPTCHA does not. have tried all the solutions support and installed the new FF. still does not. Help.

  Try creating a new profile as a test to check whether your profile is the source of the problems.

  See "basic troubleshooting: a new profile:

  • https://support.Mozilla.org/KB/basic+troubleshooting#w_8-make-a-new-profile

  There may be extensions and plugins installed by default in a new profile, so check that in "tools > Modules > Extensions & Plugins" in case there are still problems.

  If the new profile works then you can transfer files from the old profile to the new profile, but make sure not to copy corrupted files.

  See:

  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

• I bought a windows version of 11 elements and not a mac version. So I can't install the dvd and it does not accept my serial number for the "downloadversion" how this can be solved?

  I bought a windows version of 11 elements and not a mac version. So I can't install the dvd and it does not accept my serial number for the "download version" how this can be solved?

  Thank you in advance.

  Arjen

  You can also download the Mac in trial version of the software through the page linked below and then use your current serial number to activate it.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  Photoshop/Premiere Elements 11: l http://prodesigntools.com/photoshop-elements-11-direct-download-links-pse-premiere-pre.htm

• I installed the 12 elements, it does not open, a screen will appear with the options e-12 and 4 other languages

  I installed the 12 elements, it does not open, a screen will appear with the options e-12 and 4 other languages.  When I click on 12 items, a screen will appear with a red install icon, I click and it askes for the serial number. It won't let me type in letters digits only. Already, I have the serial number once. How to make this work? I don't want to be a programmer!

  attach a screenshot of what appears after clicking PES 12, http://forums.adobe.com/thread/963429

• Error "this graphics driver is not compatible with this version of windows" when you try to install the graphics card

  Title: windows 7 Enterprise 64-bit

  I have hp Pavilion dv6 2138 ca for computer pc laptop and intel hd graphics and nvidia grahics on my windows 7 Home premium 64-bit, but after I've upgraded to windows 7 Enterprise and try to install the graphics driver nvidia. It is said

  the NVIDIA Setup program cannot continue and this graphics driver is not compatible with this version of windows.

  while I chose the latest graphics driver from the hp Web site.

  kindly tell me, that means the sentence above means and what programs and features must be changed in windows? or what steps should be taken to install nvidia graphics?

  answer me

  Thank you

  Hi Hamdullah,
   
  Welcome to the Microsoft community.
   
  "I understand from the description of the issue, you do not know the error' Nvidia graphics drivers are not compatible" when you try to install the drivers. I will definitely help you with this problem.
   
  (1) what is the model of the graphics card are you using?
   
  Method 1: If the NVIDIA GeForce GT 320 M graphics driver, I suggest you to download the Nvidia graphics drivers from the link and check if it helps.
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100095-3&cc=us&DLC=en&LC=en&OS=4063&product=4125893&sw_lang =
   
  Method 2: If the problem persists, I suggest to select the graphics driver and check if you have any driver update available.
  http://www.nvidia.com/download/index.aspx?lang=en-us
   
  I hope it helps. If you have problems in the future, please let us know. We will be happy to help you.

• After the awakening of system does not see the sound card

  Hello

  I have a problem with the Hibernate. After the wake-up system do not see my card (creative sound N2 on USB key). I've been in touch with Creative and I know that I need to uninstall my laptop Realtek sound card in BIOS. Of course, I don't see any possibility in the BIOS. In Windows XP Home edition, can I uninstall this sound card, but after reboot this card is itself back installation.

  And I want to know how to completely disable Realtek.

  Hi Tomasz

  One question;
  You're talking about on a map of external sound that is connected via USB to the laptop or talk on the Realtek integrated sound card!

  I know a similar sound problem on Vista OS.
  I read in the knowledge base Microsoft on similar problems;

  Please check this:
  http://support.Microsoft.com/kb/929685/en-us

  Please provide more details if this fix will not help you!

• Professional PC HP Elite 7200 MT: cannot install the graphics card GEFORCE GT 630

  Hello

  My graphics card originally installed (HP GEFORCE GT420 2 GB) was causing my system to freeze (screen black etc.), every time I used the software that requires a lot of graphics power (like games), I decided to update my system with new cards - Geforce GT 630 (PCI-E 2.0).

  After installation, my system does not start. He goes to the HP loading screen (the one blue at the beginning) and he won't. There is no sound signal. I just different card installation if I can work on the PC, but I would use my GT 630.

  My terms of reference are:

  Professional PC HP Elite 7200 MT

  P/N: XT217EA #BED

  CPU: Intel i5-2400 @ 3, 10 GHz

  RAM: 8 GB (2 x 2 GB, 1 x 4 GB 1333 MHz)

  Motherboard: 2AB6 1.04

  System BIOS: 7.15

  Question - what type of interface PCI-E of the Protocol not 2AB6 Board of Directors system, follow-up support 1.04 (1.0? 2.0? / 3.0?)? According to Findlaptopdriver.com (http://www.findlaptopdriver.com/pegatron-2ab6-mainboard-corporation-specs-151202h39/) it supports PCI-E 2.0.

  What GPU are compatible with this motherboard: 2AB6 1.04?

  Thanks for the help

  *******************************

  EDIT:

  Just know that my PSU is only 300W, and my new GPU is 350 W to run. Looks like it's the problem.

  EDIT #2:

  Change the power supply does not resolve the issue. Now I think that the motherboard isn't compatible PCI-E 2.0 GPU.

  Hello

  Contact the video card manufacturer for repair.

  The reality is that there is no guarantee that any particular graphics card will work in any particular PC, even if the graphics card works in other PC or even the same or similar model PCs. Know what the return policy is before you buy.

• Qosmio X 70 - the SD card reader does not work

  I upgraded to 8.1 win a moment the card reader does not work. Nothing happened when I put a card inside. I tried serveral. I changed the driver to a new from the homepage of Realthek - nothing. What can I do?

  Can you please tell us what card reader device status in device (storage controller) management?

  Furthermore, what you have upgraded your machine following the instructions on http://www.toshiba.eu/innovation/generic/windows8_1-message/?

• System does not boot after changing graphics card

  I'm under VMware ESXi 4.1 on HP xw8400 workstation. He worked well with HP Nvidia Quadro FX1400 graphics card, but after a while I became tired of all that noise and he changed his Asus Nvidia 7300LE. Now the system stucks on vfat successfully loaded.

  If I re - install the system with this another graphics card, it'll work?

  Strange that a simple graphics as blocked change the boot process.

  Maybe you order card PCI is also change.

  Simple, you can reinstall your host and then re-import the VMFS volumes.

  If you have local storage, make sure not to format the existing VMFS partition.

  André

• System does not boot, get the white screen after preparation for auto repair

  Hello

  I have a Toshiba Satellite with Windows 8 and yesterday there were some ongoing update and must restart.  When the computer reboots, it took some time and then I got a blue screen (very quickly) who said something as she encountered a problem and needs to fix (it is really fast and I can't see the whole text).  Then goes and comes back as it is booting (with the toshiba logo) and he says prepare auto repair.  Then it goes to a white screen. I tried to get into the HARD drive recovery (power with F12) and when I select HDD Recovery and confirm Yes, it just goes to a blank screen.  I went into the Setup utility (powering now F2 while) and has chosen default install and who does not either (although it has fixed the problem with my keyboard backlight does not). Support of Toshiba said that it is the operating system, not the hard drive.  But I need a drive recovery media that will scan all.  Anyone know other options?  I have a disc of recovery of a Microsoft coming 8 Pro (dell).  Would it be an option, to use it (I got it on a flash drive) and start-up of that?  Thanks for the help.

  Hi John,.

  Thank you for the update.

  Given that you want to use the Windows 8.1 recovery disk, you won't perhaps able to start Windows 8 using Windows 8.1 because the computer may not be able to find the files of Windows 8 start to recover.

  Yes, you pouvez install 8.1 Windows using the recovery disk. However, you may not be able to perform the upgrade option when installing Windows 8.1. When you click install now and follow the instructions, you must choose the Custom Advanced option to continue installation. Choose Advanced custom options will create a folder in the C: drive (or any other partition when you do not want to install) named the Windows.old folder which expected to have all of your files and documents of previous installation and are accessible.

  Make sure you have the drivers available for the devices installed on the computer as network card, drivers etc. of video card you install Windows 8.1.

  Hope the information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

  Thank you.

• G2 355 J0Y60E #ABV: I can not install the graphics card on my PC

  I can NOT INSTALL GRAPHIC CARD DRIVER ON MY LABTOP I USING WINDOWS 7 PROFESSIONAL x 64 AND I HAVE ALREADY DOWNLOD THE DRIVER for MY COMPUTER PORTABLE IT STILL NOT WORKING AND
  Thank you..

  What is the error message you get when you try to install the driver?

  You have downloaded the correct driver for your graphics card? The correct driver for your laptop is mentioned in the link below:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4132 & LC = da & CC = DK & DLC = da & sw_lang = & Product = 5353028 #N6506

  Please download the softpaq and try to install this. (In case you can not install this in normal mode, try to start in safe mode (by pressing F10 during during the boot process and select "safe mode") and then check if you can install the driver.)

  You can also download and install the latest version of the BIOS from the following link:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=6886537 & swItemId = ob_135192_1 & swEnvOid = 4059

  This should help.

  If you still have problems, please post your error message here.