System does not boot after changing graphics card

Similar Questions

• Internet does not work after changing graphics card.

  Hello

  I have a HP Pavilion HPE h8-1212 on windows 7 (64-bit) and I changed my graphics card for an AMD Radeon HD 7790 so like my case.

  after reboot and installation of my graphic card drivers, I noticed that I have yet 2 "Bluetooth devices" (bluetooth device) and I don't have a Wifi connection. I am currently connected to my internet via an Ethernet cable.

  Here are some screenshots of my problems:

  

  

  Please help me with this.

  The wifi card, if it's a minimap, as it is in the image, should have had two sons goes to the card wifi which were channelled through the case.  These were responsible for picking up the wifi signals to work.  Since the screenshot shows the weak or no signal, I suspect this is the question.

  

  As to describe the process of removing antennas, I couldn't find the following steps.

  Before you start: Remove the access panel, the collar, the higher optical drive and the upper bezel.

  1. Detach the antennas wireless the wireless LAN card.
  
  
  2. Cut the cable tie fixing connectors antenna for the front i/o cable harness.
  
  
  3. Pull the antenna cables without wire through the access hole in the upper part of the unit.
  
  
  4. Pick up each cable hooks fixing the top of the page of the PC.
  
  
  5. Detach the screws for each antenna.
  
  
  6. Pull the antennas of the unit off.

  In the end, it seems that the antennas are routed right under the top cover.

• System does not boot after changing the appearance settings

  I installed XP Home successfully, but the resolution of the screen to be changed. When I followed the instructions of troubleshooting, I was unable to get to the drivers. I changed the settings on the advanced screen prompt to auto, and now after the Windows XP logo load and it I hear the hard drive running, the next screen is completely white/black. Help!

  Is this the same solution for: in the advanced options of monitor, I selected "do not use this device"?  I tried to update the driver for the monitor and reach for straws when the button 'update driver' has been 'grayed out' (not available).  I have a new HP 2009 flat screen and have just installed XP on a new hard drive.  Monitor worked, although some resolution.  The type of monitor has been defined as "default monitor" and driver is VgaSave.  Thank you!

• HP ProBook s 4540 - system does not boot after recovery

  My friend gave me the laptop, because the system has not been detected. I decided to recovery operating system.
  I had to face following error messages:

  -I did not receive "Boot Device not Found" error

  I started the HARD drive with result success test

  -next step was to recovery OS
  He finished with the new error message
  "The boot image selected is not authenticated to. "Press to continue.
  According to this topic:
  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/selected-boot-image-did-not-aut...
  I did following:
  -secureboot changed to disabled
  problem persisted

  -legacy changed to enabled
  Since then, I'm not able to do anything. When I leave the start system, it ends with the HP logo, and nothing happens.
  When I press ESC after a reboot, menu appears, but I am not able to enter the BIOS. If freezes all the time in the menu with the text highlihted.

  I tried to remove the battery, unplug the power, press the powerbutton for 30 seconds, nothing has changed.

  Next step should probably be to temporarily remove the RTC battery, but I don't know if I'm allowed to open it without losing the warranty.

  The laptop is about 3 months old.

  Hello:

  Because the laptop is under warranty, I suggest your friend contact HP technical support and ask them to solve the problem.

  When you get a not found boot device error it's hard drive (if the test says it is spent or not) or the drive controller on the motherboard.

  I wouldn't touch with a ten foot pole.

  HP support will probably have your friend go through certain stages that you did before they tell him what to do next as return them for warranty repairs, etc.

• System does not boot after CHKDSK

  Reference Dell 745, XP SP3, fully patched. Had not run CHKDSK in 5 years, machine has been in use, thought it might be a good idea. NOT!

  I plan to CHKDSK/F, he ran at the next startup, then I get the splash screen, then black screen, nothing else. If I turn the power off, the next time you start trying to run CHKDSK again, and if I run it or not, same result - start screen, then nothing. What to do next?

  The machine is in reverse now - here's "the rest of the story" - pressing F8 didn't work, couldn't get into safe mode. Recovery Console is not installed on versions of our company. I was able to get a couple of our Support service for Office XP installation diskettes - only one is bootable and even through, that's for XP SP1 and I have XP SP3, it worked.

  Choose the option to repair install didn't solve the problem at all. Once again starting on the CD, I chose the Recovery Console. At this time, I chose FixBoot and FixMBR. And then when I removed the CD and booted up again, pressing F8 gave me access to the boot with Safe Mode and other options menu. Safe mode does not work - I got nowhere (I don't remember exactly what happened at this point, but it did not help). Which does not finally was the last good Configuration. Once I chose that and rebooted, I had a relatively normal cases, slow start and connection, without the detour by CHKDSK. He has been sluggish about 10 minutes longer than normal, but worked normally since.

  I don't see any reference to CHKDSK saves in my shaft system of the observer of events tools - any suggestions on where I could display them?

  My lesson learned here - if the system is not broken, CHDSK is going to break, so on modern systems, only run CHDSK when you experience the symptoms that you can't otherwise explain. That had been the case at home on a Win7 laptop, which had suddenly slow, with a blurry view near the start icon.  I had been worried about the virus and horses of Trojan, but a suggestion in the forum Win7 on Tek-Tips pushed me to run CHKDSK, who did to solve this problem. It's a relief to be back to normal!

• Latestes Update 14.1.2 does not recognize the iMac graphics card.

  Hello

  I've updated my PS - CC to 14.1.2 and now my graphics card is not recognized.  The problem was supposed to have resolved this update.  I have an iMac 27 inch end 2012 with 32 GB memory and 1 TB of hard drive.  My graphics card is NVIDIA GeForce GTX 512 MB of 660M.   When you start PS - CC after the update, I received a message that my graphics card was not recognized and I need to update the driver.  As you have known, only Apple has updates to the graphics driver.  There is NO update driver on Apple.  Checking my preferences I don't have the ability to Open GL now.  My driver works well with 14.1.1.  I'll try to retreat towards the 14.1.1 if possible.  Any help would be appreciated!

  Dennis

  Here's an update of the above.  Just by chance, I found an interesting solution.  I restarted my computer and then open PS - CC 14.1.2.  I received the same message... PS does not recognize that your graphics card for people with disabilities advanced display options.  Otherword, NO Open GL graphics.  So, I closed PC - CC and rebooted just to see what would happen and... I don't have the error message.  Check the Preferrrence, found my recognized graphics card and I have Open GL.  If for some reason, the first time you open PC - CC 14.1.2 with iMac, your graphics card will not recognize.  Just close and open again and you'll get him back.  Weird!  Adobe, please fix this for us users of iMac!

  Dennis

• the system does not accept my new credit card?

  Hello

  the system does not accept my new credit card? Pls help...

  Hello

  You will need to contact support by calling/chat for this request.

  Contact the customer service

  * Be sure to stay connected with your Adobe ID before accessing the link above *.

  Kind regards

  Sheena

• Four-core 64-bit VISTA system does not restart after the latest updates

  My system does not at all now after SP2. It won't even load of recovery disks cannot get sytem to work repairing or family name known good config, etc..

  If you need a copy of the DVD, go to this link and download the image.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/
  Kind regards

  Today, it was a good day, I didn't have to use my AK.

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• Installing the graphics card... System does not boot

  Hello

  I received a HP P6-2387ea today (I5, 8 gb, H61 Chipset) with the intention to introduce a new GeForce660 inside that also happened today.

  The PC boots up well with its default material and very well with my addition of a 500 watt PSU... However, when I add in the GeForce 660 does not start, I am rather greeted by 6 beeps to the bios, which is obviously not a good thing.

  My first thought was gpu at fault, but I tested it on another machine and it works fine. I also took a GeForce 460 of this old machine and tried in the new HP one, same result.

  I'm missing something here, or I have a faulty card or something?

  (To avoid responses of stupidity, yes the 500w PSU is a lot and the appropriate pci-e 6pins were attached).

  Any help would be appreciated.

  Bill

  Hello

  First response to your title question is "no, your motherboard is not broken.

  Try this:

  Boot into the bios and go to the Secure --> Secure Boot Configuration topics. Now disable secure boot and turn on legacy mode. Now let's see if the PC will start using the material existing HP before you make any changes. If the PC starts, then try just a video card.

  View your results.  I have a suspicion about what the issue is for the motherboards that are active UEFI.

  --------------------------------------------

  Side note:

  It seems someone is trying to find an answer to this question using different HP computers as a way to find the answer when the PC is delivered W8 and active UEFI.

• System does not boot, get the white screen after preparation for auto repair

  Hello

  I have a Toshiba Satellite with Windows 8 and yesterday there were some ongoing update and must restart.  When the computer reboots, it took some time and then I got a blue screen (very quickly) who said something as she encountered a problem and needs to fix (it is really fast and I can't see the whole text).  Then goes and comes back as it is booting (with the toshiba logo) and he says prepare auto repair.  Then it goes to a white screen. I tried to get into the HARD drive recovery (power with F12) and when I select HDD Recovery and confirm Yes, it just goes to a blank screen.  I went into the Setup utility (powering now F2 while) and has chosen default install and who does not either (although it has fixed the problem with my keyboard backlight does not). Support of Toshiba said that it is the operating system, not the hard drive.  But I need a drive recovery media that will scan all.  Anyone know other options?  I have a disc of recovery of a Microsoft coming 8 Pro (dell).  Would it be an option, to use it (I got it on a flash drive) and start-up of that?  Thanks for the help.

  Hi John,.

  Thank you for the update.

  Given that you want to use the Windows 8.1 recovery disk, you won't perhaps able to start Windows 8 using Windows 8.1 because the computer may not be able to find the files of Windows 8 start to recover.

  Yes, you pouvez install 8.1 Windows using the recovery disk. However, you may not be able to perform the upgrade option when installing Windows 8.1. When you click install now and follow the instructions, you must choose the Custom Advanced option to continue installation. Choose Advanced custom options will create a folder in the C: drive (or any other partition when you do not want to install) named the Windows.old folder which expected to have all of your files and documents of previous installation and are accessible.

  Make sure you have the drivers available for the devices installed on the computer as network card, drivers etc. of video card you install Windows 8.1.

  Hope the information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

  Thank you.

• Download it "Boot Manager is damaged, the system will not start" after changing a hard drive.

  Original title: where and how to get the installation to win 8 pro 64 bit oem disc

  Please community, help me. First of all, I have upgraded to win 10 and it works well. So I decided to start from scratch and got a bigger hard drive and reinstall win 8. I did successfully, but when I rebooted the computer, I received a statement that says "Boot Manager is damaged, the system cannot start ', which is why I am now looking for a start or install disk for win 8 64 bit oem. I was not able to start since I received the message. Help, please.

  Hello

  Maybe that's a problem, but you can try...

  You can try to download the ISO of Windows 8 from the following link:

  Download the .exe installation of:

  http://Web.ESD.Microsoft.com/W8DL/WSEC5B1D8A9DFDFD92DFB736C5B1D8956B5B1D8/Windows8-Setup.exe

  Click on Setup.exe. The wizard of Windows 8 will begin. Enter your key of Windows 8 and press Next.

  Click install now and let the full download.

  The installation files will be stored by default in the C:\ESD\Windows folder.

  When the "Install Windows 8" message is displayed, select 'Install by creating media' to create a bootable USB key or .iso (a disk image) file. Chose a folder to store the image, for example "Windows.iso.

  OR... http://Windows.Microsoft.com/en-us/Windows-8/upgrade-product-key-only

  If this does not work, see this thread...

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/trying-to-update-from-Vista/2dd14d77-E68A-43ad-b53e-7a1afaf1d410

  BTW... You can download an ISO of 8.1 Win or create media from here...

  http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-media

• Data hold does not work after changing time system

  Hi guys,.

  I configured Oracle Data Guard successfully between a primary database and a database physical standby.

  Later, I changed the date and time in the two servers at the level of the BONE (from 14 - Sep to the 13 sept). The time is the same on both servers, but it has been changed. Then, I created a test table in the primary database, but I see not in the database of relief, well that configuration sounds good.

  Could you please explain?

  It is 11.2.0.1.0 - 64 bit Linux.

  Here is the code:

  In the primary:

  SQL > select sysdate to double;

  SYSDATE

  ---------

  13-SEVEN.-15

  SQL > desc hr.test

  Name                                      Null?    Type

  ----------------------------------------- -------- ----------------------------

  A                                                  NUMBER

  B                                                  VARCHAR2(10)

  In the database backup:

  SELECT SEQUENCE #, APPLIED, FIRST_TIME NEXT_TIME

  FROM V$ ARCHIVED_LOG BY SEQUENCE #.

  SQL > 2

  SEQUENCE # FIRST_TIM NEXT_TIME APPLIED

  ---------- --------- --------- ---------

  232 06-06-SEPT.-15-15-SEP YES

  233 06-06-SEPT.-15-15-SEP YES

  ..

  ..

  261 14-14-SEPT.-15-15-SEP YES

  262 14-14-SEPT.-15-15-SEP YES <-here it shows the old date

  31 selected lines.

  SQL > desc hr.test

  ERROR:

  ORA-04043: hr.test of the object does not exist

  In the primary db:

  SQL > alter system switch logfile;

  Modified system.

  
  

  Pending:

  SQL > SELECT SEQUENCE #, APPLIED, FIRST_TIME NEXT_TIME

  FROM V$ ARCHIVED_LOG BY SEQUENCE #.  2

  SEQUENCE # FIRST_TIM NEXT_TIME APPLIED

  ---------- --------- --------- ---------

  263 13-14-SEPT.-15-15-SEP YES

  264 13-13-SEPT.-15-15-SEP YES <-new date shows fine here

  265 13-13-SEPT.-15-15-SEP YES

  266 IN-MEMORY, 13 SEPT. 13. - 15-SEPT-15

  35 selected lines.

  
  

  SQL > desc hr.test

  ERROR:

  ORA-04043: hr.test of the object does not exist

  Hello

  You can check availability using v$ view dataguard_status.

  You can make a request on a user table at the backup site if the standby instance is in recovery mode.

  to check your test table, you must stop the recovery mode and start in read-only mode

  Cancel log apply services:

  SQL > ALTER DATABASE RECOVER MANAGED STANDBY DATABASE CANCEL;

  Open the database for read-only access:

  SQL > ALTER DATABASE OPEN READ-ONLY.

  Then you can query your table test.

  Concerning

• gSynchit does not open after changing the password

  GSynchit has stopped working. I changed the password of email account, but the program does not open if I can change the settings.

  Hello

  1. what operating system do you use?

  2. What mail client do you use?

  3 did you receive an error message when you try to run gSychit

  If you use windows7, I suggest you follow the link and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.