Internet connection is lost

Similar Questions

• My internet connection is lost at home after a few minutes. I re - turn on the wifi disabled, ten and it works again for a few minutes and then repeats. It works fine everywhere else?

  Relatively new MacBook OSX El Cap 11.4

  My internet connection is lost at home after a few minutes. I stop the wifi, then turn it back on and it works again for a few minutes and then repeats. It works fine everywhere else?

  Please see recommended settings of WiFi routers and access Apple points.

  Despite these recommendations, some routers will work better with the latest Mac models if you turn the radio 2.4 GHz mode in settings and only use the 5 GHz. Note, however, that very old devices Apple and some third-party devices can then not connect at all.

  Some third party routers have advanced that you may need to change the settings:

  The encryption algorithm must be AES.

  The group key interval must be 3200.

  I can't give you specific instructions on how to change these settings, because all routers are different. Refer to the documentation for the provider.

• my internet connection is lost during the use of the internet

  often, I find that my internet connection is lost while using the internet.how can solve the problem.

  Hello

  1. for how long are you facing this problem?

  2. don't you make changes before this problem?

  3. what operating system do you use?

  I suggest you to try with the mode safe mode with network and check.

  Start your computer in safe mode with networking

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

• The internet connection is lost when the computer puts itself to sleep after that idlen too long time needs to restart to re-establish the connection.

  I lose the internet connection

  Window vista Home premium intel core 2 quad CPU q6600 @ 2.40 ghz, 3.00 GB ram the System 32-bit

  The internet connection is lost when the computer puts itself to sleep after that idlen too long time needs to restart to re-establish the connection

  Hello

  Control Panel - device - network - manager double-click the used network - power management device
  Tab - uncheck the computer to allow him to turn off the device.

  Control Panel - Power Options - check at each change of diet Plan - change Plan settings - advanced
  Power settings - check the settings there.

  You may reset the default power Plans and and then change them as needed.

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• The Internet connection is lost after installing Windows update

  Original title: put automatic has caused the loss of access to the internet

  After that the last automatic updates have been installed on the 8/17 or 18, I lost the internet connection.

  I had to restore my computer to an earlier date. When it was complete, I had access to the internet.

  I have reset my updates for having me choose when and which ones who.  When I install the updates, how can I know who we are at the origin of the problem.  In addition, how will I be able to solve the problem?

  Hello

  What is the error when you try to access the internet after upgrades?

  Method 1: Update the network drivers

  I suggest to update the network drivers, then try to update and check if the problem persists.

  Updated a hardware driver that is not working properly

  http://windows.microsoft.com/en-US/windows7/Update-a-driver-for-hardware-that-isn ' t-work correctly.

  Method 2:

  We can find the update by installing the updates one at a time, the origin of the problem.

  To do:

  1. click on Start, type windows update and press enter

  2. click on check for updates in the left pane of the window

  3. when updates are found, open the list and select one at a time and install them.

• Internet connection is lost after 2 minutes

  In our House there are 4 teenagers - all with laptops, iphones, BlackBerry, etc.

  We have an internet connection to BT home hub.

  Everyone can connect OK except 1 latop - if using WiFi, laptop connect only for 2 minutes and he then loses the connection to the internet.

  The only way to get a WiFi connection again is to reboot the router.

  The laptop works fine when connected with an RJ45 LAN cable - problem only occurs if you use the WiFi.

  The laptop has Windows XP and Internet Explorer 8.

  The icon on the watch of the taskbar that the connection to the router is OK, and varies from excellent to mediocre according to how far the laptop is located rom the router.

  Why do I have a problem with this machine - I guess that it must be related to XP as all other machines have Vista or 7.

  Hello Gavin Duffy

  It may be possible but not likely.
  1. the system that only stays connected for 2 minutes, this problem only occurred after the settings have been changed in the router?
  2. did you check with your son that only security settings have been changed in the router?
  3. have you checked to see if this system is undergoing the same questions on other networks such as Café, the bookstore free networks or network of neighbors (the permission that they allow to connect)?
  Try to remove the wireless network profile and recreate.
  If you use 'Wireless Zero Configuration' to manage your wireless network, go to the network connections folder ("" Start > run ", type ncpa.cpl and click OK"), make a right click on the wireless network connection, select Properties, and then click the wireless networks tab, where you can highlight and then 'remove' an existing profile.
  After that you have removed, reconnect to your network and test to see if the problem still occurs.
  Thank you.

• Internet connectivity is lost every 3 days... restoration of the system, restores connectivity

  I lose the internet connection on my HP Pavilion laptop of series g on all three days.  I have to use the connectivity of the system restore restore (lan & wireless).  This is the third episode of this problem.  Troubleshooting services cannot identify/fix the problem.

  What are the events the choice of system restore show as having passed in the meantime?  Are you aware of all the events as the Windows updates?

• Internet connection is lost in computer laptop and Xbox when I fill the network.

  Original title: the network bridge is being gay

  well IM one of the problems with my network bridge that I connected to my card built into my laptop and im for my throu xbox wireless bridge the LAN, and unless he is satisfied, I have internet but when I fill my connections he said: no internet access and I can not access the internet on my laptop and now my habit of Wi - Fi allow me to connect to what anyone I don't have the shared option on check and my connection is really horribly slow and its never been this slow before

  Hello
   
  1. when the question is is produced?
  
  2. you remember of any changes to your machine before the question?
   
  I would like you to follow the steps mentioned below
   
  Step 1:
   
  Instead of bridge, you should be able to share the connection from your laptop.
   
  a. Click Start, click Control Panel
  b. go to your network and sharing Center.
  c. on the left side, click on manage network connections.
  d. right click on your wireless network adapter, click Properties, click the sharing tab, mark the tab to share this connection
  e. click on apply, then try to connect to xbox with your ethernet cable, either incidentally, it must be a crossover cable in order to function.
   
  Step 2:
   
  Disable all security software temporarily and see if the problem still occurs.
  
  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
  
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• EX7300 drops internet connectivity

  Hello

  so I bought myself an EX7300. Manual configuration went all well.

  My problem is, that, although Windows indicates that it has access to the internet and the wireless signal is at the highest level, my internet connection is lost every few minutes. I have to toggle the WIFI connection to regain access to the internet, but once again, it's just for a short period.

  When you perform a repair of Windows, the message is: Windows cannot communicate with the device or resource (primary DNS server) [main DNS server is 192.168.0.1]

  The Extender has a static IP address which is 192.168.0.50, but gives the router a DHCP IP which is 192.168.0.106.

  Firmware is the newest: 1.0.0.44

  It's really annoying and restores the Extender completely useless.

  Any suggestions?

  Thank you

  NX

  I think I solved the problem by giving the router a channel fixed wLAN (48) and the Repeater another (40). Have not had this problem since.

• Connect a HP OfficeJet Pro 8500 to router Netgear N600 loss of internet connection.

  Whenever the OfficeJet printer is connected to one of the ethernet to a Netgear N600 router ports, the internet connection is lost. Internet works without any complications, if the printer is not connected to the network. As soon as the ethernet cable from the printer is connected to the router (or a network switch) the internet connection is lost. If I look at the devices using the Netgear browser interface, everything seems appropriate. The printer uses DHCP and you will receive various IP addresses according to what remains is connected (e.g. 192.168.1.3). I've narrowed the problem to the printer, causing the loss of connectivity internet thie. Attach only my computer to the router (may be an iMac or a Windows XP system), internet works fine, plug the printer results in a loss of interest. Printer works fine and the documents can be printed after you connect to one of the ethernet ports.

  I tried to set a static IP address on the printer (e.g. 192.168.1.100) so that the attribution of a static address with the interface of Netgear using the MAC address of the printer - no approach fixes the problem. Netgear support is perplexed (they have even sent a replacement router, thinking it was defectiive, the two routers show the same problem). I have reset the printer to its default settings in order to eliminate potential conflicts with modified parameters. I also tried to change the speed of the link to something else than "Automatic", nothing seems to work.

  We will define an external static IP and DNS address for the printer.  I think that the external DNS will do the trick.

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  Your router have updated firmware?

• Cisco has disabled my internet connection I don't have the guest password - I never asked to Cisco

  My main computer is a Windows XP, I also have Vista and a laptop with Windows 7, XP is slow, the vista access no internet at all unless I put in some password for comments, that I never went also, I didn't want Cisco and if I did it lacked experience in computer science and an accident.  Please help, friends try to help and I lost all my music files and now I can't Netflix Blockbuster or Rhapsody.  Help?

  Software Cisco Connect think that my internet connection is lost, but it's not. It won't take me any further than that.  I would just use the administration of "Advanced" page but I am trying to enter to disable the guest network and for some reason, Cisco made that only configurable from the Cisco Connect software.

  http://homecommunity.Cisco.com/T5/Cisco-connect/Cisco-connect-software-thinks-my-Internet-connect-is-lost/TD-p/374485

  http://homecommunity.Cisco.com/T5/wireless-routers/setting-NAT-to-disabled-breaks-Internet-connection/TD-p/251760

• Internet connection drops connection USB

  I use windows vista and have broadband connected wireless.  Whenever I connect the printer via USB and the impression that I lose my internet connection and the printer stops working.  This happens everytime I use the USB port, I tried all ports that a USB is connected with internet connection is lost and I don't understand why!  Can someone suggest a resolution?

  Hello

  1. USB devices work when it is connected to the USB ports?

  2. What is the brand and model of the printer?

  3. When does work well before?

  4. you remember to make changes to the computer before this problem?

  Method 1:

  You can try to reinstall all USB controllers and check.

  Note: If you use a USB mouse, please follow the steps of "Using the keyboard" to reinstall the USB controllers. Windows 7 will reinstall all the controllers automatically after restarting your computer.

  Step 1:

  If you do not use a USB mouse, and then follow the steps:

  First of all, please disconnect all USB devices and then perform the following steps:

  a. click "Start", type "Device Manager" (without the quotes) in the search bar and press "Enter." If necessary, click on continue.

  b. in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click 'OK '.

  c. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows Vista will automatically reinstall all USB controllers.

  Step 2:

  Follow the steps if you are using the keyboard to uninstall the USB controllers.

  First of all, please disconnect all USB devices. Then go through the following steps:

  a. press "Ctrl + Esc" to open the Start Menu.

  b. management of devices of the type in the search bar and press "Enter." If necessary, click on continue.

  (c) in the Device Manager, press Tab and use 'Up' and 'Down' to move the selection from 'de Bus USB controllers '.

  d. Press 'Right' and expand it.

  e. press "Down" to move to the first item, and then press "Delete" to delete.

  f. Repeat step 5 and uninstall everything under 'controllers of Bus USB '.

  Method 2:

  You can check if the printer is compatible with Windows Vista.

  See the link for compatibility:

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/

  Method 3:

  You can also try to update the wireless card and check.

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-drivers-recommended-links

  Hope this information is useful.

• Lose internet connectivity by downloading photos (Windows Vista)

  I have a super frustrating problem that no one could help me with. Whenever I try to upload a photo from my computer to a Web site (attach photos to an add-on, order photographic proofs online etc.) the internet connection is lost and I have "local access" only. In order to make it work again I have to reset the modem. Any suggestions would be much appreciated.

  Go to the website of the manufacturer of your Modem > make sure you have the latest Firmware in Vista for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• My internet connection keeps going on and outside.

  On the icon bar of signal a yellow triangle with an exclamation point comes up often, and the internet connection is lost. I have verizon fios and my other computers work. Once I start the computer it takes time so that it connects to the internet. I installed on my computer and, recently, for some reason any that it says I have to renew my subscription even if my validity up to the year next to macafee. Who would have something to do with it. Please advice.

  Hello

  1. What is the brand and model of the computer?

  2 have you made any changes to the computer, before the show?

  Method 1:

  Run the network troubleshooter, and check.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Method 2:

  Step 1: Safe Mode with networking

  Start your computer in safe mode with network and verify that the question.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Note: The advanced startup options, select Safe mode with network.

  Step 2: Clean boot

  If you are not facing the problem in safe mode with network, then put your computer in a clean boot and search for the issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once you are done with the boot, follow step 7 in the article to restore your computer to normal startup.

  Method 3:

  Disable the antivirus and check if you face the same problem.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Note: Runs the computer without antivirus software or firewall is a potential threat to the computer; don't forget to activate the security software after completing the troubleshooting steps and after you have identified the problem.

  Method 4:

  Update the NIC drivers and check.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• I lost the internet connection, how do I reinstall

  I lost my internet connection to my Mini Ipad how can I reinstall

  Look for some troubleshooting steps based here.

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network