Internet connection through different VLAN

Similar Questions

• Wake on LAN (WOL) through different VLAN on SG-300-10

  Hello

  I try to get WOL working through different VLAN on a Switch SG-300-10 in layer 3 Mode.  To achieve this, I set up a UDP relay (GUI menu Configuration IP) for UDP Port 7 to 255.255.255.255 (this should inundate all interfaces with the package), however, does not work WOL in different VLANS.  When I am connected directly to the VLAN corresponding, WOL works fine in the same subnet.  Am I missing something here?

  All comments appreciated!

  Thank you very much!

  Hi Romeo,.

  A few minutes to try it on my SG300 - 10 p mode layer 3.

  My NAS unit is capable WOL and I thought I would use it in my test environment...

  Ran a basic test to check my sender of packet Magic from my PC "awakened" my NAS unit.

  As you would expect, on the same subnet, the magic packet WOL caused my NAS unit to power, no problem.

  But this isn't really the test, just a test database to check that my sender of the packet magic WOL and NAS was working well.

  The screenshot below shows WOL software I used on my PC.  Why use this software, no reason except that it was available for free. Also, I'm sure other WOL software out there for different platforms that work just as well or with more features.

  

  First of all, I see according to your question, you used relays UDP destination port 7, well it is the default setting on the UDP relay on my switch.

  I wonder why you used or stayed with destination UDP port 7, because the Magic packet mailers may use different destination UDP ports?

  I had to use wireshark to see the real destination UDP port that uses my sender of the magic packet WOL.

  

  Notice of capturing wireshark above, that my magic packet software uses the UDP port destination 9, NOT the default value that you can see on the switch. Ignore what wireshark labels this port.

  OK, I then created a VLAN that I named "VLAN2' with a = 2 VID on my SG300 - 10 p (SRW2008P-K9-NA)

  I added a 192.168.2.1/24 IP interface to VLAN2, which is a different network from the default VLAN.

  I then added three ports this VLAN newly created as a member untagged VLAN2.

  The default VLAN (VID = 1) an IP network 192.168.10.0/24.

  My NAS (WOL capable) unit has an IP address of 192.168.10.61.

  I plugged my PCt to the vlan 2 and statically assigned 192.168.2.2/24.  It is the PC that has the magic package software.

  I added a route static to my router WAN, just so that I could access the router my PC attached to the VLAN2 WAN.

  I tried the magic packet WOL software and will not turn on my NAS.  He expected that the magic packet broadcast would never jump over a limit of LAN in one VLAN different...

  Now, I tried to install a UDP relay so that the Magic Packet WOL "would be" the VLAN2 network interface VLAN1.

  So I configure and add to my SG300 UDP relay entry - 10 p.   See the screen capture below.

  I have to admit, I'm used to using UDP relay normally take a netbios broadcast and unicast to a server Ms.

  But check the screenshot below, I put the switch to send the UDP relay to the broadcast address of VLAN1 network... The magic packet Wakeup sent from my PC into 2 VLANS must have passed over the limit VLAN that my NAS unit woke.

  

  In order to check the destination port UDP to your WOL software using wireshark, and then create an appropriate UDP relay.

  Experiment and play with that, once you get your device WOL properly powereing successfully.

  Best regards, Dave

  If I answered your question, please rate the relevance of this response

• Can not share the internet connection through Wifi

  Hi all

  I am connected to the internet using an external antenna connected via USB to my mac (WIRELESS n 801.11). I want to share this connection since my mac with other devices, i.e. my iPhone. I use the internet connection through system preferences--> sharing--> sharing internet--> connection on the part of wlan to computers via WIFI and give a name and a password for the wifi settings. When I start the connection icon wifi on the the high watch the arrow menu to the top, but it gives an IP address from 169 auto... etc etc and I can't any traffic to my iPhone.

  I tried to configure IPv4 to use DHCP with a manual (instead of automatic DHCP) address and IP I enter the IP address used in the WiFi, wifi says that it is connected to the name of the internet connection in the shared connection, I opened but once again no traffic to the iPhone. Also tried disabling the firewall, once again nothing.

  I run El Capitan 10.11.2.

  Clues?

  OS X El Capitan: share your Internet connection

• Need me a firewall if my internet connection through a router. I'm with Virgin and I have a D-Link router

  Need me a firewall if my internet connection through a router. I'm with Virgin and I have a D-Link router

  On Friday, June 8, 2012 14:45:42 + 0000, Ian 213 wrote:

  Need me a firewall if my internet connection through a router. I'm with Virgin and I have a D-Link router

  Your router provides firewall protection, so the need is not the same
  as if you had no a router. There are some who say you need to no.
  all firewall software.

  But my opinion is that you would be a lot safer if you have run a
  router software, and since there is little reason not to, I
  recommend that you do.

  Ken Blake, Microsoft MVP

  I agree.

  @OP Windows XP (SP2 and above), Vista, 7 and 8 all have active firewall software by default.

  There is no need of any 3rd party firewall.

  Some users like running programs such as ZoneAlarm because it warns him from the processes that use the network, and then there is the possibility to deny/allow it on the spot, or deny/allow forever. There may be slight discomfort in the installation, but once it's for all your programs, and then it really can work in silent mode.

  Microsoft Firewall simply leave everything default, but they can be configured manually to block anything outgoing or incoming.

• get internet connection through another computer...

  Hello

  I would go straight to the point :)

  I have a desktop running windows vista. I have a normal internet connection through a router that connects to the internet on this desktop computer.

  now, I also have a laptop with windows xp and here is what I do. my laptop's wireless was always bothers me, sometimes it connects, sometimes it doesn't work out... so I saw that there is an Ethernet card installed in the laptop with an Ethernet port.

  My question is this:

  I have a lot of Ethernet cables at home and I was wondering if there is a way to get internet to my laptop via the Ethernet port on my desktop, but without needing the desktop computer to be running, cause I only use my laptop these days and my router is too far to connect from my room. I hope you understand my problem. In theory, I think it's possible to do, but I'm not sure how, so please help me on this one. my laptop also has firewire, but I prefer ethernet for some reason any.

  Thank you

  Hello

  Sorry, but you cannot get a connection via another computer if the computer is off.

  I'm not sure that I understand completely the topology.  However, if the office is connected by cable to a router for Internet connection, you can solve the problem by buying a simple network switch.

  You take the cable from the desktop and connect to the switch. Then you plug the desktop and laptop computer at the switch.

  That this switch network does, it divides a cable to feed many computers.

  Example of a switch that can be connected with a cable to a router and feed 5 computers.

  http://www.Newegg.com/product/product.aspx?item=N82E16833166034-

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Having trouble with my internet connection through wifi. N600 router is what I think.

  I had some problems with my internet connection recently via my wireless router. I get the little triangle yellow and with the connection at different times and I can't call my local internet provider because it still works when they are open, and then it closes when they are closed. I recently bought a Google Chromecast and some think it might interfere with the connection, but I don't see how. When I reset the modem router and cable by unplugging and plug their return they sometimes get the rear connection but it's annoying not knowing when it will go off again, then come back. A few months before the connection out sometimes but not several times a day. If you need additional information such as the type IP DNS stuff I can get it. Also recently I have updated the firmware of the Netgear if that makes a difference. Thank you!

  Thanks to all who responded. I talked to my ISP and discovered that the modem was abandon the connection because he was old and he sold me a new and things work fine now. Thanks again!

• Cannot get internet connection through wireless network

  I have a Sony VAIO laptop that came with Vista 32 bit and went from 7 Home Premium 32 bit.  I connect to the internet via my Ethernet via a DSL modem with no problems.  When I try to use the edge Intel 4965AGN wireless to connect to my DLink 655 Wireless N Gigabit router, it appears that it connects to the network, but there is no internet connection.  Both the router and the edge Intel have the latest drivers and the encryption is set on AES, WPA2-Personal.  Some additional information:

  I have desktop computer Dell with a DLink USB WiFi and it connects to the network and gets internet

  I constantly get the message from Windows saying: Windows has detected an IP address conflict with another computer on the network.  I restarted the router several times to no effect.

  In network and sharing Center (of course the troubleshooting network said he found nothing) the network appears as a Public and unidentified and it gives me no option to change it to a home network.

  I tried to connect to other networks public wireless (hotspots) and I can't connect it

  Hello

  Something is wrong with the TCP/IP parameters.

  Autoconfiguration IPv4 address:169.254.1 52.88
  IPv4 subnet mask: 255.255.0.0
  Autoconfiguration IPv4 address: 192.168.0.1
  IPv4 subnet mask: 255.255.255.0
  IPv4 default gateway:

  This 169.254.1 52.88 is the IP by default Windows assigns when there is no DHCP server, this isn't a working IP address.

  The second IP address is the IP address of the Wired card. That is why router conflicted reports.

  Configure the two cards for full Auto obtain IP and DNS.

  Then do a WinSock and TCP/IP updating.

  Type Cmd in the search text box.

  Press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type netsh winsock reset at the command prompt and press the Enter key.

  Do the same process to refresh the TCP/IP just replace the command typed with.

  netsh interface ipv4 reset Press enter

  netsh interface ipv6 reset Press enter

  ipconfig/flushdns press Enter

  Restart your computer.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• I have to start two times to get an internet connection through my ZyXEL_P-2602HWT-F1

  Hello
  I have W7 64 Pro SP1 and it worked well until I get a new modem ZyXEL_P-2602HWT-F1 from my internet provider. In almost the same time that I upgraded W7 SP1 so I don't know which is the cause of this problem I have. If I boot my computer for any reason, I don't get any internet connection. I have to start again.

  My other computers get internet connection immediately as above machine before these two changes.

  Please help me find out what's wrong because it's very irritating.

  PIKO

  Hello

  This looks like a problem of driver for me. I communicate with your access provider which you gave the new modem and ask them where the driver is available for download. I could find this model on the site of ZyXEL either.

• Problem with internet connection through WIFI A536

  Hello.
  I bought a few days ago the A536 Lenovo.
  It works very well, it will connect to any wifi that I choose without problem, but after a while it stops internet access without obvious reason.
  He remains connected to WiFi, it keeps the same IP address, I have access to the router (ping works, and I can access the router configuration) in my browser but I don't have access to the internet from any application (browser, Skype, Viber, Mail, etc...)

  I tried a different WiFi (public) and has the same problem.
  (My laptop and a phone HTC Wildfire, Guard works well all the time at home)

  If I just simply disable and enable the WiFi antenna, it connects and it works again for 20-120 min

  I tried to restart, disable Firewall (and security), disable all applications that could affect internet access, add applications 'safe list' firewall, I even downloaded "Lenovo companion" but it is impossible to find problems.
  Wifi after awhile stops all communications to the internet.
  It is very annoying, because no internet means no messages, no emails and no calls VOIP programs.

  Anyone has the same problem?

  Is this A536 fault, or is this the Android 4.4.2?
  Is there a solution, or I have to restore my phone while I can and select a different template, such that it is unnecessary in the end I bought?

  Hi Draculas,

  1 check if there is no update firmware
  2. restoration of the factory

  If the problem persists then take to service center.

• I can determine the amount of traffic to/from my Internet connection through my Airport due to each connected device (both wireless and Ethernet)?

  My traffic internet, as reported by my ISP, has increased significantly in the past few months and I would like to determine where this increase. Devices that potentially connect via my Airport are:

  Wireless:-2 iPad, 2 iPhones, iPods, MacBook Pro

  Ethernet:-desktop HP, Swann CCTV security system.

  Unfortunately, airport routers provide no information on the use of the data of the connected devices, or the product itself.

  I'm not aware of a 3rd party application that would do exactly what you want... but someone else may know, and if all goes well they after.

• PS3 internet connection through my Verizon Wireless card

  I would like to help connect my PS3 to my card from Verizon that works on my laptop wireless. (Dell Windows Vista)
  A detailed description would be great...
  Thx for any help

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  The question you have posted is related to the Playstation. Unfortunately, we can not help with third party software/hardware changes.

  Please contact the manufacturer for assistance.

  http://boardsus.PlayStation.com/PlayStation/

  http://www.us.PlayStation.com/support

  WARNING OF THIRD PARTY SOFTWARE

  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Kind regards

  KarthiK TP

• No internet connection but the status is "connected" - Qosmio G30-163

  Why can't internet connection through some wireless networks, and never through the connection to the local network, even if the State of the connection is "connected"?

  I have a Toshiba Qosmio G30-163

  In the Manager of peripheral devices, network cards, there are two yellow mark points (next to "Other devices" and "Multimedia video controller")

  I made sure "Obtain IP address automatically" is a selection and "Obtain DNS address automatically" is selected as well.

  the IP address of my computer is 169.254.xxx, x, and I read somewhere that this indicates that there is no connection to a DHCP server and probably no connection at all. I was not able to renew the IP address.

  To repair internet connection doesn't work. I get the response "Windows could not finish repairing the problem because it is impossible to perform the following action: renewing your IP address." "For assistance, contact the personal who manages your network.

  Thank you

  Anne

  Try turning off the Windows Firewall. Or if you have installed a lot of 'Internet Security', reconfigure or disable the firewall.

  Update the BIOS and make sure have the latest network drivers and wireless installed.

  Try another browser such as Firefox or Google Chrome and verify that the Proxy settings are correct (if you are behind a proxy).

  Go to a command prompt and type: IPCONFIG/all
  If you see a gateway, you must be connected to the Internet.

• I have my internet connection by wi fi my network is configured but my printer is not printing I uninstall this driver I reinstalled it but still nothing what to do?

  I even uninstall my printer, reinstalled it and still nothing

  I have a window that opens with network problem

  I tried beautiful I find nothing

  I do have internet connections through wi fi

  What do I do

  Thank you for your answer

  Hello

  See this page to select your language:

  http://support.Microsoft.com/common/international.aspx

  ====================================

  Or sorry that it is area English.

  On the top of this page of answers (English) v -click and set your language.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Failure of Internet connection, Pc network in network connection is OK

  I have a PC, Windows XP Professional, networking in the office with Novell.  I can connect to the server, Novell and normal work. The internet connection through the server.   I can't connect to the internet.  I went to the Network Diagnostics for WindowsXP. I show several errors, the 2 1st, HTTPS: error 12037 connecting to www.microsoft.com : the date of the certificate is invalid or has expired. Then same error, attempts to connect to www.passport.net.   Then HTTP:error12029 connecting to www.microsoft.com. A connection with the server could not be established.  Then Sucessfully Info FTP (passive): connected to FTP.Microsoft.com. any information will be appreciated.

  Hi pouteign,
   
  As you are facing this problem with the machine that is connected to the Desktop server, contact the respective system administrator to solve this problem.

• Internet connection sharing does not work anymore

  I have used Windows Vista Home Premium for 2 years now on my laptop. Internet connection sharing enabled to connect to the internet via my wireless adapter and allowed me to share my internet connection through the ethernet port. He worked for more than a year. All of a sudden 4 months ago Windows Vista doesn't let me share the internet connection more. When I go to networking and sharing Center, click on "Manage network connections" and it shows that my "Wireless Network Connection" is always set to share. So after reading several forums, I clicked on wireless network connections and click right properties. Then I clicked on the sharing tab, to make sure that "Allow other network users to connect through this computer's Internet connection" has been verified and that it is. After that, Windows Vista will not always share the internet. Someone suggested that I double check the IP version 4 and 6 on the wireless and Ethernet connection were defined on IP addresses obtain automatically, and they are. The computer still will not share the internet connection! I even took the manufacturer in the view of portable and made sure my cable modem Simulator wasn't bad. I took it to a computer store and we checked the crossover cable. Everything is fine! What else can I try?

  Obtain an IP address automatically is the wrong setting on the Ethernet connection.  To return to the sharing tab and unshare the wireless connection.  Close all windows network, and then open them and re - share the wireless connection.  Who must configure IPv4 for the Ethernet connection properties for:

  IP address: 192.168.0.1
  Subnet mask: 255.255.255.0
  Default gateway: no
  DNS server: no
    
  Owner, Boulder computer Maven
  Most Microsoft Valuable Professional