Iomega ix4 - 200 d - disk not ready

Similar Questions

• Iomega IX4 - 200 d - Boot Loop

  Hello.

  Hello.

  We currently have an Iomega IX4 - 200 d that is stuck on a loop of Boot Logo Iomega.

  I have posted a youtube video showing the issue in order to provide a better explanation.

  https://www.YouTube.com/watch?v=aGLS5HfHPLM

  The unit worked perfectly well and all the sudden we noticed that we had any access to the content.

  At the time that I arrived at the unit, it's this way.

  Content have already been recovered using a machine linux, and now the 4 HARD drives have been tested and are 100% functional.

  We tried a few methods found on internet, HARD drive partitions were removed and all, but we just can't get the device to work.

  Any help is welcome.

  Best regards
  Paulo brine.

  OK, I managed to fix my Iomega IX4 - 200 d, not supported by Lenovo, but in any case, for those who seek to challenge their units, you can find all the necessary files and instructions here:

  https://www.dropbox.com/sh/f3eq457tgw6nfnd/AADNpvcxRYwKqoOC0mTlC978a?DL=0

  Best regards

  Paulo brine.

• Iomega ix4-200 d Firmware

  Hey,.

  I have inheridted an ix4 - 200 d, but the unit is stuck at the boot.

  The only thing left to try is a Firmware recovery, but where can I get the recovery files of?

  Hello Tularis,

  You must contact the local support for it:
  https://Lenovo-EU-en.custhelp.com/app/answers/detail/A_ID/14722

• Iomega ix4-200 d upgrade to latest version of the firmware

  I recently got this unit and want to update to the latest version of the firmware but I get an error message stating that "this update applies only to version 2.1.31 and more.»

  Try to upgrade to version 2.1.42.18967 - I think that it is the most recent?

  Current version of the firmware is 2.1.25.229

  It seems that I might have to upgrade to version 2.1.3 first and then proceed to the latest version.

  Can someone please help?

  Thank you

  Hi Danp_Vic,

  If your StorCenter ix4 - 200 d runs a version lower than 2.1.31, you need to update using the ix4-200 d-ix4-200 d - 2.1.38.22294.tgz before the update to 2.1.42.18967.

• Encryption of files on iomega ix4 - 200 d

  Hi all

  I would like to know if there is a way to put an encryption of files within the NAS, not only the SSL protocol in the communication.

  Thank you all

  tstcweb,

  I looked in the manual for the device:
  http://download.Lenovo.com/nasupdate/manuals/ix4-200d_cloud/ix4-200d_en_us.PDF

  And it doesn't seem like there is no way to encrypt the data using native firmware.

• Ix4 - 200 d showing not SMART for hdd3 and 4 hard drive

  Hello
  I tried to check the SMART status of my drive for hard disks and found it works just to punch two (HDD 1 and HDD2)

  For the last two, what a show - SMART not supported while it shows smart health and all the INTELLIGENT features enabled on both drives. Also I can see SMART tree to these two readers if I plug them into trays 1 and 2 respectively. of course, I can see all the statutes SMART if I connect all four disks to another PC.

  My readers are Hitachi 2 TB

  Device has been updated to the latest firmware.

  Thoughts?

  Thank you!

  Closed question - his work with d - sat: smartctl - a d Sam/dev/sdc

• ESXI 4 update 1 connected to iomega ix4 - 200 d Iscasi of work

  Hello

  On the iomega device, I set iscasi 2.5 TB drive

  I could connect the ESXI on the second interface directly to the iomega box and and I saw the iomega set to work as an iscasi server.

  What use of Vsphere to add a data store can see capacity: 2.5 to BUT available only 451 GB!

  What can I do to get the whole 2.5 available to

  Y at - it no limitation of Iscasi anywhere?

  Thank you

  There is no limitation for iSCSI as such but the limitation to the VMFS file system is 2 TB - 512 bytes, you can try to present a LUN size 2 TB - 512 bytes and tell us what is the result?

  You can view the maximum rates of http://www.vmware.com/pdf/vsphere4/r41/vsp_41_config_max.pdf configuration guide

  If you have found this or other useful information, please consider awarding points to 'Correct' or 'useful '.

  f 10

  VCP3, VCP4, HPCP, HP UX CSA

  http://KB.VMware.com/

• Iomega StorCenter ix4 - 200 d rebuild failure

  I have a StoreCenter ix4 - 200 d, which had a disk failure. I bought another disc with the same model number and I replaced the damaged drive. During the restart of the screen on the StoreCenter says "disk 1 requires overwrite confirmation", but when I go to the dashboard, there is no confirmation message, and he has not lost all records storage and shows 0 stored data.

  It sounds like the raid/pool failed. If you retrieved the data and not concerned about this on the NAS, you can try a factory reset. It is data destructive but should rebuild your raid and allow you to use it again.

• Satellite Pro 440 CDT - message "the disk you selected is not ready."

  I have an old Satellite Pro 440 CDT with a CD drive (no floppy more) who plays the music well, but when I type and want to save to a cd, he comes up with the message "the disk you selected is not ready. Can anyone help, because really, I'm not an irritable type and need help.

  I know it as an irrelivent bits to your problem, but I suggest that you invest in a USB key. They are pretty well the replacement disks are much more portable than a CD.

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete

• Virtual Disk Manager "the device is not ready".

  I don't know about the format from outside, possibly MAC OS EXTENDED. He was not ejected a Mac and will not mount on an operating system MAC or PC (Windows 7 Professional) using Firewire (800 to 800 and 800 to 400), eSATA and USB 2.0. When I use disk management, disk will appear as not initialized and next to the "disk 33", there is a red arrow pointing down. Whenever I open the Disk Manager, the window to initialize the disk appears, but once I chose a style of partition and press OK, the virtual disk manager pops up saying "the device is not ready". I also tried to wipe the drive using CMD, (disc of DiskPart/list / select disk 33/clean), CMD said the drive was clean, but when I went to disk management, without change.

  I'm looking for a way to clean the drive so that it can be reformatted and reused.

  Hi Catherine,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the link below.

  http://social.technet.Microsoft.com/forums/Windows/en-us/7e214b16-E415-449a-8f25-4cace51e5106/Virtual-Disk-Manager-error

  Good day!

• Disks HARD IX4 - 200 d always running

  With an another IX4 - 200 d (no-cloud edition) my hard drives are running all the time, even if there is no activity!

  It is very noisy.

  Anyone knows how to fix?

  Thank you

  The defective pneumatic drill has been Media Server!

• ix4 - 200 d IP problem

  After spending a whole day trying to figure this issue out, I gave up to do what I don't know. I recently got an ix4 - 200 d from a friend. When I booted up the SIN for the first time that everything works as it should. The other day I moved and takes the SIN with me to my new location, now the thing starts fine, but no matter how to configure networks setting - after it restarts the software the setting looked back the default values (169.254.x.x). The only time I can have access to this device is if I plug directly on it with a crossover cable and install a network of Point 2 Point with her. There are several people who relay on this NAS for their use of personal storage and without my network came to a screeching halt. What should I do to get it working properly again? Here's what I've done so far: reset the NAS via the restart button powered down the NAS and held the button for 30 secs linked directly in NAS via splitter cable manually the IP address and gateway to the 192.168.X.X network pull on all disks in and started the downloaded NAS Lenovo Solution Manager - only to find out that I can't find the SIN at all. Connect the NAS directly on the router which has the internet connection - which is the same router, it was initially attached to when I arrived the SIN at this point that I am totally lost on what to do next. Someone please help!

  Resolved - the NAS reset randomly and all parameters were back the way they were... Not my problems

• Unable to stop ix4 - 200 d

  Hello world!

  I can't manage to stop my ix4 - 200 d which is frozen (impossible to access data or the web interface). Using the button before turning off does not at all, even if I continued pushing on it for 30 seconds.

  Is there only the solution of unplugging the power cable? The last time I did, one disc was missing after reboot... :-(

  Thanks for any help!

  If your network storage unit is under warranty I would have you call technical support.

  United States and in the Canada, please call 800-940-6354, option 1, between the hours of 09:00 and 22:00
  EST, Monday to Friday, and that a representative would be more than happy to
  talk with you about your Iomega product.

• Replace HARD drive in ix4 - 200 d with 4 No 3 TB drives

  I just traded all four 2 TB HDD in my iomega with 3 TB Seagate NAS drives. It was RAID 5 and I swapped each three days. All reconstructions of data protection took place without a hitch.

  I was expecting when I replaced the fourth drive capacity would increase from 5.4 to about 8.1 but he didn't not. It shows all the hard drives 3 drives to and total size TB 10.9 but just under that number on the same page, total capacity is still only 5.4 and NAS still 90% full.

  I tried to restart, but no change.

  All my data is backed up on my Synologies, but after taking the time to rebuild the data on the iomega RAID and not to lose, I would rather unload everything if I can avoid it.

  Pls advise. What should I do next?

  Hi Niko-Lenovo,

  What version of the firmware on your ix4 - 200 d? You may need to do a factory reset of the web interface, which is destructive of data. When replacing all readers to improve the storage capacity, usually data are saved and removed from the unit, then transferred to the unit after the upgrade. Please see: upgrade storage capacity for an ix-series network storage device