IP address of server blades management

Similar Questions

• Reference Dell R310 Server Blade not start CD ROM [FRESH WINDOWS SETUP]

  Hello

  I have a Server Blade Dell R310. I created the virtual disk on a Raid Configuration, also I updated the BIOS boot.

  I PERC S100 when I checked on my configuration tab.

  The scenario is that I want to install a new / new copy of Windows 2008 R2 on this server, I have the dvd bootable. but when I put it on the drive it says "No Bootable Media found" something like that.

  Y at - it all the configurations that I missed? hoping to get answers from here.

  Kind regards!

  OK, let's back up a bit:

  Use the management tools of systems and Documentation (GDPS) instead of SBUU.  If you use SBUU with 2008R2, you should use the Driver Pack too... MUCH easier to use the GDPS, which has everything you need in there:

  FTP (you will need to copy/paste - forums do not like the FTP links):

  FTP://FTP.Dell.com/secure/FOLDER01538030M/1/OM_SMTD_730_A00.ISO

  Yes, you start on GDPS, follow the instructions, and then insert the 2008R2 media when prompted.

• Server Blade ASYNC / threshold of passage / hardware verification

  Hey people,

  strange things occur yesterday evening. I bypassed about 120 messages "threshold crossed: CAW: etherTxStats...» "and"IO Module Warning.

  I looked in the events of UCSM. Each server blade in our UCS started a WSF. What is a routine of UCS? We do not know what is happening. All the 32 ESXi 5.5 blade server. It has not changed anything.

  Events of WSF see attached file. I have filtered all the events of 'jumps '. To me, it seems that MMIC began the new inventory for all servers? Do you know something about this or have the same events? Is there a scheduled task internal UCS?

  UCS version 2.2 (3f) (all systems = same beam of firmware; UCSM, FIs, blades...)

  Thank you very much

  / Hugo

  It would be interesting to have a look at the audit logs around that time and DME (data base management Enginer) to see what is really happening... You better open a case of TAC and then post the result here for future users faced with the same question it will require a deep investigation of the newspapers before we a tell you what/why he happeed.

  -Kenny

• Error in the SMTP Configurations for File Server Resource Manager

  Hello

  Please help me how to configure SMTP for file server resource manager, when I have set up SMTP for gmail and godady e-mail I got the error.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)

  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, its error message that gives as no network device connected. Suggest me!

  Original title: problem in installing FSRM

  We are trying to install FSRM (File Server Resource Manager) in windows server 2 k 3 R2 SP2. After installation, open the FSRM in "All programs", its error message that gives as no network device connected.  Suggest me!

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

• Shut down Windows XP: "program end" "sql server service manager.

  I use Windows XP SP3.  When I turned off my computer, I get an error message with "End program - SQL Server Service Manager" in the title of the window.

  How can I get Windows XP to shut down without this error?
  Thank you

  Winner!

  Final solution was to use of AutoRuns to disable the four entrances to the SQL.  Using AutoRuns, I still did not have to change the registry and did not have to uninstall all the software,.
  The four entries in AutoRuns entries are:
  (1) in "C:\Documents and Settings\All Users\Menu Menu\Programs\Startup"
  The AutoRun entry: Service Manager.lnk
  Description: SQL Server Service Manager
  Publisher: Microsoft Corporation
  Image path: c:\program files\microsoft sql server\80\tools\binn\sqlmangr.exe
  (2) in "HKLM\System\CurrentControlSet\Services" (can also be found in Services of AutoRuns tab"
  The AutoRun entry: MSSQL$ MICROSOFTSMLBIZ
  Description: SQL Server Windows NT
  Publisher: Microsoft Corporation
  Image path: c:\program files\microsoft sql server\mssql$microsoftsmlbiz\binn\sqlservr.exe
  (3) in "HKLM\System\CurrentControlSet\Services" (can also be found in Services of AutoRuns tab"
  The AutoRun entry: MSSQLServerADHelper

  Description: Microsoft SQL Server Active Directory Helper Service

  Publisher: Microsoft Corporation

  Image path: c:\program files\microsoft sql server\80\tools\binn\sqladhlp.exe

  (4) in "HKLM\System\CurrentControlSet\Services" (can also be found in Services of AutoRuns tab"

  The AutoRun entry: SQLAgent$ MICROSOFTSMLBIZ

  Description: Microsoft SQL Server Agent

  Publisher: Microsoft Corporation

  Image path: c:\program files\microsoft sql server\mssql$microsoftsmlbiz\binn\sqlagent.exe

  Thanks for all the help!

• Need help sql server 2008 management Studio.

  I imported a sql database to use Expression Web 4 according to a tutorial I followed from C:\Program Files\Microsoft SQL Server\MSSQL10_50.SQLEXPRESS\MSSQL\DATA. Later, SQL Server 2008 Management Studio running on XP3 returns error that it is impossible to browse the database, which is still on display in the DATA folder that contains all the other databases, as well as in the Expression Web folder, in that it has been copied. How the database for me to work with Management Studio? Glaust

  Glaust, did you eventually get this working or is this even a question? If you can provide a little more information about what you were doing to import you talk. Am I right in assuming that your instance of SQL Server has the database is available for you to access through SSMS. Then, you have completed the import and now you can see the DB in the SSMS DB tree but you get the error and are unable to access the DB?

  Thank you

• SQL Server 2005 Management Studio Query Export to CSV to the Non Unicode Format

  In SQL Server 2005 Management Studio, click the part of the results of a query.  Click on "save results under...". ", select CSV and an output file.

  The output is in unicode format. How can I fix this in ASCII?

  Jim Oliver

  Hi Jim,.

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the forum.

  Link:http://social.technet.microsoft.com/Forums/en-US/category/sqlserver/

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Activate connections encrypted for the database engine (SQL Server Configuration Manager)

  Hi team,

  I have a quick question, on the protocols for properties of SQL. Option:

  SQL Server Configuration Manager > SQL Server Network Configuration > Protocol for SQL_xxx (right click) > properties, we can see two tabs:

  Tab 1: flags

  Tab 2: certificate

  If I put the value of Instance of hide = Yes, 'Force Enctyption', the fact must be set to YES as well?

  Or Enctyption of the Force must be activated in order to hide the instance?

  What is recommend settings?

  I can see there are good article, but would appreciate if a response.

  https://msdn.Microsoft.com/en-us/library/ms191192.aspx

  Thank you

  + Moin

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• Unable to connect to the MKS: address for server esx02.mgmt.domainname.dk host lookup failed: unknown error 11002 (0x2afa)

  I get the following error when I connect to my via Vsphere Vcenter and try to connect to one of my server with the console:

  Unable to connect to the MKS: address for server esx02.mgmt.domainname.dk host lookup failed: unknown error 11002 (0x2afa)

  I'm new to VMware, I can very well do a MSTSC server and work proberly.

  the VMwareTools are out of date, when I log on the server and try to update I get the following message:

  

  any ideas here?

  I discovered that it is related to DNS

  WSATRY_AGAIN

  11002 (0x2afa)

  It is usually a temporary error during hostname resolution and means that the local server does not valuationauront of response from an authoritative server.

  the issue was that the VMware system was on a different subnet, and the firewall (TMG) blocked. bring the RDP to the Vcenter server and vsphere then open works like a charm

• How do I know if a host server is managed by a vcenter Server?

  I found an ESXi server in my server room, and I can connect with the root username. How will I know if this server is managed by a Vcenter server somewhere when you are connected to the host with vmware customer?

  When you connect with the VMware client, there will be a popup message in the sense of "this host is managed by vCenter, etc etc. I remember not exactly beyond saying that it is hard to miss.

• vCenter Server and Manager on the same virtual machine and on the same host ESXi update that they manage

  Hi all

  I have a question to which I did not respond.

  I have an ESXi 5 on Proliant DL380 G7 server host. I want to install vCenter Server and Manager Update on one of the Server 2008 R2 VM on the same host. I know it's possible, but my question is how Update manager will provide updates to the same ESXi host it will run on? The update is applied every time host must spend in maintenance mode and power off the virtual computer running on this subject which means he'll kill VM where vCenter Server and Update Manager is running and the update will fail right?

  Is that possible at all or the VCS and UM such as a virtual computer operating point is updated to other guests if you have them or vMotion as VM to another host when you want to update the VCS and UM host is running?

  Thanks in advance.

  It will not work.  You will need at least two hosts.  This way you can vMotion the vCenter VM to another host.  From there, you can use VUM.  Otherwise, you will need to patch the host as a stand-alone host.

  See below for patching a standalone host

  http://communities.VMware.com/people/vmroyale/blog/2011/09/15/updating-ESXi-5--single-use-esxcli-how-to

• Cannot locate the Microsoft Sysprep package on the server Lab Manager

  I have created a new model using the Lab Manager and install Windows XP 64-bit on it.  When the virtual machine has been cancelled and I tried to publish... I have the following error Publishing...

  Cannot publish a model of

  * Could not locate the Microsoft Sysprep package on the server Lab Manager.

  This 64-bit Windows system requires the package to perform the configuration of comments.

  See the documentation on the creation of the package.*

  When the sysprep package must be on the labmanager... I have a WinXP_64 directory, located in...

  Server\Tools\LMTools\Sysprep C:\Program VMware Lab Manager the Lab Manager server.  I also ran sysprep on the master, that I am trying to publish.  Anyone who encountered this?

  A few sites to check out:

  • http://pubs.VMware.com/labmanager3/users/LM_Users_Guide_templates.7.16.html -> note, you must have all the files in all the folders to build the package

  • http://pubs.VMware.com/labmanager3/users/LM_Users_Guide_templates.7.17.html

• ISE server receives requests for authentication of the bridge VLAN, not the IP Address of the switch management

  Hello

  A 3850 catalyst switch has VLAN 20 (10.18.4.32/29) defined on it, which has a 10.18.4.38 gateway:

  D01-01-BWY #show ip short int vlan 20
  Interface IP-Address OK? Method State Protocol
  Vlan20 10.18.4.38 YES manual up up

  A server of ISE (SNS3415) is connected to a port configured on VLAN 20, with IP address of 10.18.4.33.

  01-BWY-D01 has to a management interface of 10.18.4.17.

  I created this switch as a device network in ISE and activated the RADIUS config and then configured the switch with the following commands:

  RADIUS attribute 6 sur-pour-login-auth server
  RADIUS attribute 6 support-multiple server
  Server RADIUS attribute 8 include-in-access-req
  RADIUS attribute 25-application access server include
  dead-criteria 5 tent 3 times RADIUS server
  RADIUS-server host 10.18.4.33 auth-port 1812 acct-port 1813 borders 7 1521030916792F077C236436125657
  RADIUS-server host 10.18.4.35 auth-port 1812 acct-port 1813 borders 7 02350C5E19550B02185E580D044653

  radius of the IP source-interface GigabitEthernet1/0/1

  The problem:

  When I test the functionality of RADIUS using the following command, it fails. HOWEVER, the customer (switch) IP listed in the error log in the front door of the VLAN 20 (!):

  test the aaa group RADIUS server 10.18.4.33 auth-port 1812 Capita123 user radius acct-port 1813! new-code

  10.18.4.38 is the gateway IP address of the VLAN that hosts the servers of the ISE, I don't understand why its listed in error as IP device logs!

  ource Timestamp 2016-06-22 16:38:02.826 Receipt of timestamp 2016-06-22 16:38:02.841 Policy Server GLS-ISE-01 Event 5413, accounting RADIUS-Request dropped Reason for failure 11007 could locate no device network or Client AAA Resolution Check if the device network or AAA client is configured in: Administration > network resources > network devices First cause Could not find the network device or the AAA Client while accessing NAS by IP during authentication. Type of service Box NAS IPv4 address 10.18.4.38

  Other attributes ConfigVersionId 118 Port of the device 1646 DestinationPort 1813 Protocol RADIUS ACCT-status-Type Update-intermediate ACCT-Delay-Time 15 ACCT-Session-Id 00000000 ACCT-Authentic RADIUS AcsSessionID GLS-ISE-01/255868885/32 IP address of the device 10.18.4.38

  If I reconfigure the switch to the ISE - peripheral network and give it the IP address of 10.18.4.38 (the ip of the gateway), my radius authentication tests suddenly becomes successful.

  can someone clarify the situation what is happening here?

  I need to be able to define multiple switches by their unique IP addresses.

  Thanks for your time

  m

  Hello

  The only time I saw that it was due to use a deprecated command: radius server host.  There was a bug on the IOS XR platform as well.

  Could you please reconfigure your order of RADIUS by using the new command: radius server? And test again?

  The doc of Cisco for the new order:

  http://www.Cisco.com/c/en/us/products/collateral/iOS-NX-OS-software/iDEN...

  Thank you

  PS: Please do not forget to rate and score as good response if this solves your problem

• on the side of client vpn ip address Apple Server help

  Hello

  i've got server apple running on a mac mini running yosemite and I put it in place for the vpn and everything works well on the server-side and client-side. I have what may be a stupid question so patient with me. When I'm on my machine client and vpn is connected, in order to access the storage disk, I have running on my server I have to enter the static ip address, that I attributed to my server. call 192.168.0.14. My question is: what happens if my router on the client computer affects 192.168.0.14 on a device? This results in a conflict? can I assign a static ip address within a range of numbers greater than my server so it's less likely to happen? I'm worrying about something stupid? I'm doing something wrong? Thanks to a light that you can throw on this dilemma.

  George

  Your network server should not be in the same subnet as the network that you are from the connection.   Which means that subnets 192.168.0.0/24 and 192.168.1.0/24 - is the range 192.168.0.1 to 192.168.1.254 - should be avoided.   Better to use a subnet or block 172.16.0.0/12 one subnet in the 10.0.0.0/8 block.  Usually a 24 (255.255.255.0) subnet somewhere in the range of 172.16.0.1 to 172.31.255.254 or 10.0.0.1 to 10.255.255.254, respectively.

  If you are entering the IP address of your server, then the DNS server is either not properly configured the address IP of the DNS server is not communicated to the VPN client or there is something other odd here.

  If your 'router' - probably a gateway box IP offering a combination of IP, NAT router, firewall, port forwarding, and Server features DHCP - past through apparently, built-in DHCP server IP address then you want set up to prevent it to the addresses that you have assigned statically.   In other words, the DHCP server should not be configured with a pool of available IP addresses that include statically assigned IP addresses.

  If you prefer, you can have your OS X Server act as DHCP server and disable the DHCP service in the IP gateway.

  The features and configuration and management of the gateway box varies.