IP address of the IPSec VPN client did not get distributed via EIGRP

Similar Questions

• Problems connecting to help connect any and the Ipsec VPN Client

  I have problems connecting with the VPN client connect no matter what.  I can connect with the Ipsec VPN client in Windows 7 32 bit.

  Here is my latest config running.

  Thank you for taking the time to read this.

  passwd encrypted W/KqlBn3sSTvaD0T

  no names

  name 192.168.1.117 kylewooddesk kyle description

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  boot system Disk0: / asa822 - k8.bin

  passive FTP mode

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  domain wood.local

  permit same-security-traffic intra-interface

  object-group service rdp tcp

  access rdp Description

  EQ port 3389 object

  outside_access_in list extended access permit tcp any interface outside eq 3389

  outside_access_in list extended access permit tcp any interface outside eq 8080

  outside_access_in list extended access permit tcp any interface outside eq 3334

  outside_access_in to access extended list ip 192.168.5.0 allow 255.255.255.240 192.168.1.0 255.255.255.0

  woodgroup_splitTunnelAcl list standard access allowed host 192.168.1.117

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

  outside_access_in_1 list extended access permit tcp any host 192.168.1.117 eq 3389

  woodgroup_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0

  inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240

  inside_nat0_outbound_1 to access extended list ip 192.168.5.0 allow 255.255.255.240 all

  inside_test list extended access permit icmp any host 192.168.1.117

  no pager

  Enable logging

  timestamp of the record

  asdm of logging of information

  Debugging trace record

  Within 1500 MTU

  Outside 1500 MTU

  mask pool local Kyle 192.168.5.1 - 192.168.5.10 IP 255.255.255.0

  IP local pool vpnpool 192.168.1.220 - 192.168.1.230

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 631.bin

  don't allow no asdm history

  ARP timeout 14400

  Global (inside) 1 interface

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound_1

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static interface 3389 (indoor, outdoor) 192.168.1.117 tcp 3389 netmask 255.255.255.255 dns

  public static tcp (indoor, outdoor) interface 8080 192.168.1.117 8080 netmask 255.255.255.255

  public static tcp (indoor, outdoor) interface 3334 192.168.1.86 3334 netmask 255.255.255.255

  static (inside, upside down) 75.65.238.40 192.168.1.117 netmask 255.255.255.255

  Access-group outside_access_in in interface outside

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  WebVPN

  the files enable exploration

  activate the entry in the file

  enable http proxy

  Enable URL-entry

  SVC request no svc default

  AAA authentication http LOCAL console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.168.1.0 255.255.255.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd dns 8.8.8.8 8.8.4.4

  dhcpd lease 3000

  !

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  host of statistical threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image

  enable SVC

  internal sslwood group policy

  attributes of the strategy of group sslwood

  VPN-tunnel-Protocol svc webvpn

  WebVPN

  list of URLS no

  internal group woodgroup strategy

  woodgroup group policy attributes

  value of server DNS 8.8.8.8 8.8.4.4

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list woodgroup_splitTunnelAcl_1

  mrkylewood encrypted Q4339wmn1ourxj9X privilege 15 password username

  username mrkylewood attributes

  VPN-group-policy sslwood

  VPN - connections 3

  VPN-tunnel-Protocol svc webvpn

  value of group-lock sslwood

  WebVPN

  SVC request no webvpn default

  tunnel-group woodgroup type remote access

  tunnel-group woodgroup General attributes

  address pool Kyle

  Group Policy - by default-woodgroup

  tunnel-group woodgroup ipsec-attributes

  pre-shared key *.

  type tunnel-group sslwood remote access

  tunnel-group sslwood General-attributes

  address pool Kyle

  authentication-server-group (inside) LOCAL

  authentication-server-group (outside LOCAL)

  Group Policy - by default-sslwood

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the netbios

  inspect the rsh

  inspect the rtsp

  inspect the skinny

  inspect esmtp

  inspect sqlnet

  inspect sunrpc

  inspect the tftp

  inspect the sip

  inspect xdmcp

  Review the ip options

  type of policy-card inspect dns MY_DNS_INSPECT_MAP

  parameters

  !

  global service-policy global_policy

  context of prompt hostname

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  http https://tools.cisco.com/its/service/...es/DDCEService destination address

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:6fa8db79bcf695080cbdc1159b409360

  : end

  asawood (config) #.

  You also need to add the following:

  WebVPN

  tunnel-group-list activate

  output

  tunnel-group sslwood webvpn-attributes

  activation of the Group sslwood alias

  Let us know if it works.

• Function of automatic update for the IPsec VPN Client

  Hello.

  Do you have anyone ever tried the PIX / ASA ' feature IPsec VPN Client Auto-Update?

  (see also Document ID: 105606).

  He wants to make sure that I understand this right.

  The user will receive a popup of information telling him to download the latest version of the client? And then there start the update itself?

  If so, this would mean that the user must have the rights of full adminsitative using a laptop.

  From my point of view, full administrator rights on a laptop are prohibited - 100% and therefore the functionality would be totally useless.

  Anyone who can tell me whether I am good or bad?

  Best

  Frank

  Frank,

  You are right, if the computer desktop or labtop is completely locked regarding the installation of the software the customer won't be able to install it, they may be able to download from the link that you configured in ASA, once they connect to your server ASA RA but with regard to the installation user's machine needs rights profile appropriate to be able to install it.

  HTH

  -Jorge

• Procurement of the game Clash of Clans the sum was deducted from the iTunes account and did not get the jewelry... help me solve this problem

  the procurement process from the shock of the clans the amount was deducted in full and did not get the gems has helped me

  Have you contacted the developer of the game? If you have, and they cannot / does not help, then try to contact iTunes Support: http://reportaproblem.apple.com

  Edit: Corrected URL

• Pro at the Expert level, but did not get the Badge of alum Expert

  Hi moderators,

  Recently, last Saturday, I joined master of expert of level.

  This takes me Pro to Expert level, but did not get the Badge of Expert as well as the associated points Expert badge Alum Alum.

  Y at - it no other milestone needs to fill for the alum Badge other than 10,000 Expert?

  I mentioned this link Rewards and recognition FAQ - Oracle Community

  Kind regards

  Jitendra

  'Alum' badges refer to the word of the ancients (as far as I know) and have been allocated specifically to people who have reached certain levels in the old scoring system.  These aren't the badges you can win in the new system of gamification, they just received in the framework of recognition of what level people reached in the old system. for example, I have a badge 'Guru Alum' because I was a 'Guru' status under the old system.  If I had not reached this level before the changes then I would never be able to get this badge now.

• Have problems with the IPSec VPN Client and several target networks

  I use an ASA 5520 8.2 (4) running.

  My goal is to get a VPN client to access more than one network within the network, for example, I need VPN client IPSec and power establish tcp connections on servers to 192.168.210.x and 10.21.9.x and 10.21.3.x

  I think I'm close to having this resolved, but seems to have a routing problem. Which I think is relevant include:

  Net1: 192.168.210.0/32

  NET2: 10.21.0.0/16

  NET2 has several subnets defined VIRTUAL local network:

  DeviceManagement (vlan91): 10.21.9.0/32

  Servers (vlan31): 10.21.3.0/32

  # See the road

  Code: C - connected, S - static, RIP, M - mobile - IGRP, R - I, B - BGP

  D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone

  N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2

  E1 - OSPF external type 1, E2 - external OSPF of type 2, E - EGP

  i - IS - L1 - IS - IS level 1, L2 - IS - IS IS level 2, AI - IS inter zone

  * - candidate by default, U - static route by user, o - ODR

  P periodical downloaded static route

  Gateway of last resort is x.x.x.x network 0.0.0.0

  C 192.168.210.0 255.255.255.0 is directly connected to the inside

  C 216.185.85.92 255.255.255.252 is directly connected to the outside of the

  C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement

  C 10.21.3.0 255.255.255.0 is directly connected, servers

  S * 0.0.0.0 0.0.0.0 [1/0] via x.x.x.x, outdoor

  I can communicate freely between all networks from the inside.

  interface GigabitEthernet0/0

  Description * INTERNAL NETWORK *.

  Speed 1000

  full duplex

  nameif inside

  security-level 100

  IP 192.168.210.1 255.255.255.0

  OSPF hello-interval 2

  OSPF dead-interval 7

  !

  interface Redundant1.31

  VLAN 31

  nameif servers

  security-level 100

  IP 10.21.3.1 255.255.255.0

  !

  interface Redundant1.91

  VLAN 91

  nameif DeviceManagement

  security-level 100

  IP 10.21.9.1 255.255.255.0

  permit same-security-traffic inter-interface

  NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0

  IP local pool vpnpool 172.31.255.1 - 172.31.255.254 mask 255.255.255.0

  Overall 101 (external) interface

  NAT (inside) 0-list of access NO_NAT

  NAT (inside) 101 192.168.210.0 255.255.255.0

  NAT (servers) 101 10.21.3.0 255.255.255.0

  NAT (DeviceManagement) 101 10.21.9.0 255.255.255.0

  static (inside, DeviceManagement) 192.168.210.0 192.168.210.0 netmask 255.255.255.0

  static (inside, servers) 192.168.210.0 192.168.210.0 netmask 255.255.255.0

  static (servers, upside down) 10.21.3.0 10.21.3.0 netmask 255.255.255.0

  static (DeviceManagement, upside down) 10.21.9.0 10.21.9.0 netmask 255.255.255.0

  access list IN LAN extended permitted tcp 192.168.210.0 255.255.255.0 any

  access list IN LAN extended permit udp 192.168.210.0 255.255.255.0 any

  LAN-IN scope ip 192.168.210.0 access list allow 255.255.255.0 any

  LAN-IN extended access list allow icmp 192.168.210.0 255.255.255.0 any

  access list IN LAN extended permitted tcp 10.21.0.0 255.255.0.0 any

  access list IN LAN extended permitted udp 10.21.0.0 255.255.0.0 any

  LAN-IN scope 10.21.0.0 ip access list allow 255.255.0.0 any

  LAN-IN extended access list allow icmp 10.21.0.0 255.255.0.0 any

  standard access list permits 192.168.210.0 SPLIT-TUNNEL 255.255.255.0

  standard access list permits 10.21.0.0 SPLIT-TUNNEL 255.255.0.0

  group-access LAN-IN in the interface inside

  internal VPNUSERS group policy

  attributes of the VPNUSERS group policy

  value of server DNS 216.185.64.6

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value of SPLIT TUNNEL

  field default value internal - Network.com

  type VPNUSERS tunnel-group remote access

  tunnel-group VPNUSERS General attributes

  address vpnpool pool

  strategy-group-by default VPNUSERS

  tunnel-group VPNUSERS ipsec-attributes

  pre-shared key *.

  When a user establishes a VPN connection, their local routing tables have routes through the tunnel to the 10.21.0.0/16 and the 192.168.210.0/32.

  They are only able to communicate with the network 192.168.210.0/32, however.

  I tried to add the following, but it does not help:

  router ospf 1000

  router ID - 192.168.210.1

  Network 10.21.0.0 255.255.0.0 area 1

  network 192.168.210.0 255.255.255.252 area 0

  area 1

  Can anyone help me please with this problem? There could be a bunch of superfluous things here, and if you could show me, too, I'd be very happy. If you need more information on the config, I'll be happy to provide.

  Hello Kenneth,

  Based on the appliance's routing table, I can see the following

  C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement

  C 10.21.3.0 255.255.255.0 is directly connected, servers

  C 192.168.210.0 255.255.255.0 is directly connected to the inside

  And you try to connect to the 3 of them.

  Politics of Split tunnel is very good, the VPN configuration is fine

  The problem is here

  NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0

  NAT (inside) 0-list of access NO_NAT

  Dude, you point to just inside interface and 2 other subnets are on the device management interface and the interface of servers... That is the question

  Now how to solve

  NO_NAT ip 192.168.210.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0

  no access list NO_NAT extended permits all ip 172.31.255.0 255.255.255.0

  NO_NAT_SERVERS ip 10.21.3.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0

  NAT (SERVERS) 0 ACCESS-LIST NO_NAT_SERVERS

  Permit access-list no.-NAT_DEVICEMANAGMENT ip 10.21.9.0 255.255.255.0 172.31.255.0 255.255.255.0

  NAT (deviceManagment) 0-no.-NAT_DEVICEMANAGMENT access list

  Any other questions... Sure... Be sure to note all my answers.

  Julio

• Ping LAN internal via the IPSec VPN Client

  It's my scenario.

  Software Version 7.2 (1)

  I activated the VPN in the external Interface. The IPSec Client pool is in the range 192.168.98.150 - 192.168.98.175.

  • Allowed "a whole icmp" out Interface access both within the Interface.
  • ICMP & ICMP error inspection is enabled.
  • NAT-control is disabled.

  Clients are unable to ping any IP within the LAN 'inside' but at the same time, they are able to access the devices in the LAN using HTTP, HTTPS, SSH & TELNET.

  CASE 1:

  access-list SHEEP extended permits all ip 192.168.98.0 255.255.255.0

  NAT (Inside) 0 access-list SHEEP

  I get the following log "translation portmap creation failed for CBC icmp outdoors"

  CASE 2:

  If I add a static 192.168.98.0 public (exterior, Interior) 192.168.98.0 netmask 255.255.255.0

  I am able to Ping and the problem is solved.

  Could someone explain please this behavior?

  1. Why ICMP only needs a NAT device when TCP & UDP traffic works very well.
  2. Why a portmap translation error? Why not dynamic identity NAT?

  Hello

  So he was correspondent to a configuration 'nat' on the 'outside' interface that had no configuration corresponding 'global' for the destination (probably inside) interface which caused problems and produces the 'portmap' error.

  Please do not forget to mark an answer as the correct answer, if she answered your question or useful rate responses

  -Jouni

• Can connect to the IPSec VPN, but can not see the internal network

  I have several users that can connect to our rooms of ussing IPSec VPN on a 5505. I have a user who can connect, but cannot see the internal network. This user is using DSL with a speedstream 4100. However, I have another user with the same configuration that can connect and see the internal network. Newspapers in ASDM show the link, but do not seem to show any errors trying to access internal. Any help will be greatly appreciated. Thank you, Bill.

  Add...

  ISAKMP nat-traversal crypto

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• IPsec VPN Client - aggressive mode

  Hi all

  I just got got off the phone with the customer who underwent a check sweep of security from a third-party vendor. One of the vulnerebilities mentioned in the report is this:

  

  I know that only the IPsec VPN client using aggressive mode to negotiate Phase I. So my question is how to convince my customer to continue to use the IPsec VPN? Is this what can I do to reduce the risk of the use of this type of access remotely. In addition, am I saw the same problem, if I use SSL based VPN Client?

  Kind regards

  Marty

  Hello

  Ikev1 HUB in aggressive mode sends his PSK hash in the second package as well as its public DH value.

  It is indeed a weakness of slope Protocol.

  To be able to act on this, U will be on the path to capture this stream in order to the brute force of the hash [which is not obvious - but not impossible.

  This issue is seriously attenuated by activating XAUTH [authentication].

  Xauth happens after the DH, so under encryption.

  Assuming that the strong password policy is in use, it is so very very very difficult to find the right combination of username/password.

  Ikev2 is much safer in this respect and this is the right way.

  See you soon,.

  Olivier

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• AAA ipsec vpn clients how to see the history of connection on asdm or asa5510

  Hello all, I would like to know how see history of connection ipsec vpn client users, they authenticate to the local aaa, not in active directory. I am able to see the current logon session. go to monitoring\vpn\vpn statistics\sessions, this shows me sessions underway, but I would like to see for example the connections client vpn for the last month. I did some research and saw the info on aaa Server? I checked that article and does not see what I was looking for.

  It's actually a called (NPS) network policy server microsoft radius server.

  The one I used (ACS 5 and ACS 5) who was just an example.

  You can review the below listed doc

  http://fixingitpro.com/2009/09/08/using-Windows-Server-2008-as-a-RADIUS-server-for-a-Cisco-ASA/

  Jatin kone

  -Does the rate of useful messages-

• ASA static IP Addressing for IPSec VPN Client

  Hello guys.

  I use a Cisco ASA 5540 with version 8.4.
  I need to assign a static IP address to a VPN client. I saw in the documentation Cisco that this can be done to validate the user against the local ASA and in the user account database, you assign a dedicated IP address, or using the vpn-framed-ip-address CLI command.
  The problem is that the customer never gets this address and it always gets one of the pool in the political group. If I delete this pool, the client can't get any address.
  No idea on how to fix this or how can I give this static IP address to a specific VPN client?
  Thank you.

  Your welcome please check the response as correct and mark.

  See you soon

• Cisco ASA5520 facing ISP with private IP address. How to get the IPSec VPN through the internet?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  Hello guys,.

  I have Cisco ASA5520 facing the ISP with private IP address. We don't have a router and how to get the IPSec VPN through the internet?

  The question statement not the interface pointing to ISP isn't IP address private and inside as well.

  Firewall configuration:

  Firewall outside interface Gi0 10.0.1.2 > ISP 10.0.1.1 with security-level 0

  Firewall inside the interface Ethernet0 192.168.1.1 > LAN switch 192.168.1.2 with security-level 100

  I have public IP block 199.9.9.1/28

  How can I use the public IP address to create the IPSec VPN tunnel between two sites across the internet?

  can I assign a public IP address on the Gig1 inside the interface with the security level of 100 and how to apply inside to carry on this interface?

  If I configure > firewall inside of the item in gi1 interface ip address 199.9.9.1/28 with security-level 100. How to make a safe lane VPN through this interface on the internet?

  I'm used to the public IP address allocation to the interface outside of the firewall and private inside the interface IP address.

  Please help with configuration examples and advise.

  Thank you

  Eric

  Unfortunately, you can only complete the VPN connection on the interface the VPN connection source, in your case the external interface.

  3 options:

  (1) connect a router in front of the ASA and assign your public ip address to the ASA outside interface.

  OR /.

  (2) If your ISP can perform static translation of 1 to 1, then you can always finish the VPN on the external interface and ask your provider what is the static ip address assigned to your ASA out of the IP (10.0.1.2) - this will launch the VPN of bidirectionally

  OR /.

  (3) If your ISP performs PAT (dynamic NAT), then you can only start the tunnel VPN on the side of the ASA and the other end of the tunnel must be configured to allow VPN LAN-to-LAN dynamics.

• Assign the static IP address by ISE, ASA VPN clients

  We will integrate the remote access ASA VPN service with a new 1.2 ISE.

  Authentication is performed in Active directory. After authentication, can address assigned to a specific user of VPN by ISE IP?

  This means that the same VPN user will always get the same IP address. Thank you.

  Daniel,

  You can override the IETF-RADIUS-Framed-IP-Address in the authorization policy.

  However if I may make a suggestion:

  Unless you have only a handful of users to do so, it may be appropriate to assign the address of ISE pool or perform the mapping of LDAP attributes on ASA itself.

  In the latter case, the IP addresses are kept on the server as LDAP attributes and ASA will map the IP address. You don't want to keep address IP DB in several places.

  M.