IP WLAN configuration

Similar Questions

• Toshiba 46TL938G loses the WLan configuration after stopping down

  Hello

  46TL938G unpacked yesterday, updated the firmware on the Internet.

  Wireless set in place with WPS works, but configuration is lost after turning the TV market / back.
  I can't use assisted because of hidden SSID configuration.

  In manual mode, I always get a bad autorhization information and/or encryption not supported. Access point uses WPA2-PSK AES.

  Is it possible to Setup WPS paste?

  Any news?
  I recommend you try different configuration scenarios:

  -try password that are more than 8 to 10 characters.
  -Try different encryptions: WPE / WPA - PSK / WPA2-PSK (AES, TKIP or AES and TKIP)
  -try to connect with prior authentication ON and OFF
  -try to connect to the WLan using option hidden network - enabled or disabled

• Problems with the WLAN configuration

  I can connect my raspberry using PuTTY on a static IP, but it does not work using WLAN.

  WLAN using my router sees a device no is not an IP address, which I suppose Raspberry.

  I guess that the tutorial is wrong, as it provides the same IP for the eth0 and wlan0, and it does not show the 'network' line in the section wlan0.

  Or I do something wrong?

  Here is the final solution to my problems. At the same time, there had been several configuration errors:

  1. I provided the two devices, eth0 and wlan0, the same IP address, as has been requested by the guidelines of Tom. Of course, this won't work. I had to provide separate IP addresses as @stainsb correctly pointed.
  2. My router was set to "isolate the wlan" which means that wlan is routed to the internet but not lan. Certainly to be able to communicate between lan and wlan, there must be no insulation. So I dropped this security feature.
  3. My router was set to "restrict the mac addresses" which means that only devices can connect to WiFi. Of course, I had to relax this restriction by adding the MAC of the WiFi dongle to the list of allowed devices.

  With this three changes I use eth0 and wlan0 successfully at the same time!

  BTW, it was not necessary or use wpa pairwise or wpa-group, as suggested by @khooke_acn.

  Thanks to all and sorry for bothering with my stupid administrative problems!

• ip WLAN configuration - missing option to set the gateway and proxy...?

  Hello!

  I need to put the default gateway and the ip proxy addresses after you connect to an access point with wpa2.

  For example my htc incredible may do very well in the installation behind wifi opions.

  I think that he whould do a good idea to config for gateway, dns and proxy server server ip config wlan just after ssid-choosing the Tablet I remember 4 the next connection... a bit like the login made 4 me.

  Could sb here please give me a hint how to solve my problem of connection up there?

  I really like the A1 ThinkPad Tablet after using it 4 about 10 days now... 4 I can fully recommend the purchase and improve my gadget favorite... :-)

  (mod edit: changed the title of the post to match the wire because the question is about the thinkpad rather than the A1 ideapad Tablet Tablet)

  Under settings to go wireless and networks

  under Wi - Fi networks

  Press and hold the connection that you want to change

  Select 'change network '.

  Scroll profile

  Change the automatic to manual Proxy settings

  Enter your settings

  In this place you can also change your DHCP server static IP address

• 32L4333DG TV - need help with configuring WLAN

  I bought a flat 32L4333DG of Toshiba, but cannot configure the wireless connection.
  Help me please.

  Message was edited: assignment has been translated

  What's the problem? Have you read the instructions in the manual how to connect WiFi TV?

  There are 3 different methods to configure the WLan configuration:

  _1) easy Setup (WPS) _
  + If the AP is WPS compatible, this method can be used. +
  + WPS is a standard of the industry, designed to facilitate the wireless LAN connection and security settings. WPS automatically configures all the wireless settings. +
  + NOTE: WEP encryption is perhaps not able to configure through easy implementation. +

  _2) assisted Setup (installation using notification s AP information) _
  + Name network, authentication and encryption are decided according to the information provided by the AP. You can manually set the security key. +
  + The security key must conform to these conditions: +.
  + TKIP/AES: ASCII 8-63 or 64 Hex characters +.
  + WEP: codes ASCII 13 5 or 10 or 26 Hex characters +.
  + There's a key ID to set for the WEP encryption. +

  _3 _) manual configuration (manual entry of all parameters)
  + Some types of encryption are only compatible with specific authentication types. +
  + When authentication is an open system, only WEP or none is compatible. +
  + When authentication is shared key, WEP is compatible. +
  + When authentication is WPA - PSK or WPA2-PSK, TKIP or AES is compatible. +

  + When the inconsistent authentication/encryption pairings are detected, a warning message will be displayed and no connection attempt will be until the conflict is resolved. +

  + There's a key ID to set for the WEP encryption. +

• Tecra A2-use windows to configure my wireless network.

  I have this option checked, but frequently during the day the box is unchecked and I lose settings. Once checked once again everything is Ok. Does anyone else have this problem and found a cure?

  Hello

  I had this problem with configuring Wlan Windows but only because I used the Intel ProSet utility and clean windows option.
  If the Intel ProSet utility began then the windows option has been disabled because the Intel ProSet utility undertook the Wlan configuration

  I think you should check if some WLan 3rd party tools are not loaded in the background

• Satellite A500 - unable to connect to the WLan

  I'd like someone to help me.

  Have recently bought a satellite A500.
  I'm new in the world of laptops so I'm wrong.
  I connected to a router via a modem, the two netgear, the news.

  Had the two config for my network. Works well as long as ethernet is connected to the router of computer.

  My wireless icon on the front of the laptop is orange.
  If this should be green as the router?

  Pressing FN f8 it tell me wireless is connected.
  When I remove the ethernet cable it tell me to fix the problem, I need to plug in the ethernet cable.
  But I want to go wireless, I'm sure I'm missing something.

  Rang netgear but after that my router and it is not connected to wireless technology they could help me more.
  I use windows7.

  Thanks to anyone who can help me.

  > My wireless icon on the front of the laptop is orange.
  > Should it be green as the router?

  The WLan led can only be ON or OFF. If the light comes on (any color) then it means that the Wlan switch is on!

  It seems that the WiFi is enabled. In this case, you will need to properly configure the WiFi network.
  You can use the own WLan settings in Windows or a Wlan configuration tool like Intel ProSet utility.

  First need choose the right SSID (wireless network name), right of encryption (WEP, WPA, etc.) and password encryption.
  Please note that all of these parameters should be the same on the router WLan and WLan configuration software!

  Please check if the firewall does not affect the connection to the internet as well!

  PS: make sure you use the latest version of the WLan driver
  Here you can find the drivers:
  http://APS2.toshiba-tro.de/WLAN/

  In addition, search and read comments here on the forum!

• Problem connecting WLan on Satellite A60-186

  I have a problem with Atheros AR5004g wireless network card on my PC since I bought it.
  The problem is that if I try to connect the PC to any WiFi network that is found in the 'network' the system startup list to try the connection and write me this message: ' Attesa disponibiliti¿½ rete in corso "or... in the meantime translated"the availability of the network. but the connection never starts.

  But... and it's funny... If I set up as manual connections of the "network list" a set up as the only automatic connections (e.g. access point) and I turn off the access point I can see it disappear in the form of the "network list". If I turn on once more and click on update network list, the wireless connection to the access point will automatically launch. The IP address and DNS address are automatically given to the system and it starts to work. But if I close the connection I can not connect once more (unless I'm not the same game).

  The thing is that:
  -l' wireless adapter works (it doesn't is not out of the question use should not function even with 'games')
  -I can not connect to any network 'normally '.
  Can someone help me understand what the problem is?
  Is it possible that I need to update the wireless adapter driver?

  Thanks in advance for your help.
  Ciao

  Hello

  Your ad is a little confusing.
  You do not write on the connection. Have you used the windows WLan configuration or the Atheros WLan utility?
  I advise to use the Atheros Wlan utility to configure the WiFi connection, because it is an Atheros Wlan card.
  Of course, you can also check the availability of updates. If the new driver has been on the Toshiba site so you can try to install it.

• My Satellite C850D has problem in WLAN signal

  I had a problem with the connection to the internet wireless in recent weeks.

  I sometimes luck and he would take our router at home, but more often there otherwise the computer monitor with the x bit red in it at the bottom of my screen.

  He could not pick up any network at all. If I help it, he just repeatedly told me that I needed to install an ethernet cable, but I want to connect wireless.

  I Googled it and saw a lot of things about the drivers and I assumed it was my problem. I uninstalled my two wireless drivers and then scanned a new hardware, like the many tutorials will tell you, but nothing happened.

  I went to the Toshiba site and seemed to wireless drivers so I downloaded the Realtek one and followed internet tutorials to get this working but once again, nothing.

  Now, I don't know what to do.

  Can someone please. I need access to the internet at home for College work as soon as POSSIBLE!

  Thank you!

  Hello

  I think you should start solving the problem by checking some key things:
  First the wireless network card should be recognized in the Device Manager and it must not contain any yellow exclamation point. The WLan driver must be installed correctly.

  Second, please check if the wireless network adapter is enabled. All Toshiba laptops media function keys and generally you can activate the WLan using FN + F8 keys or (in some cases Fn + F12)

  You should check the WLan configuration.
  You can add new Wlan profile in Control Panel-> network and sharing Center-> wireless (left)
  Add new Wlan connection.

  Note: use the exactly the same settings that were used in your router settings.
  Pay attention to the standard of encryption and the encryption key!

  In the Device Manager-> card Wlan-> properties-> Advanced tab, you can see options as for example WiFi 802.11 A/B/G standard, etc.

• Satellite Pro L300 - cannot use Intel ProSet WLan tool with Win XP

  Hello! I have the same problem. I installed a XP SP3 and I can't use the * Fn + F8 * hotkey to activate the WLAN function on or off. Other Fn keys work correctly. The WiFi network also works, but it can be used by the built-in Windows. Intel ProSet or Atheros programs do not work. It seems "no wlan driver installed. The card is a Realtek 8187 B, downloaded the driver on Toshiba support original site. What can I do?

  > WLan also works, but it can be used by the built-in Windows. Intel ProSet or Atheros programs do not work
  If the WiFi works fine using the windows zero configuration then the WLan adapter is enabled and don t get the FN + F8.

  The fact is that your 3rd party WLan configuration tool doesn t work because your wireless network card is * Realtek! *

  Intel ProSet ONLY works with Intel WLan card and the Atheros Wlan configuration tool can be used ONLY if your have an Atheros Wlan card.

  You have Realtek so use windows own zero configuration WLan!

• Can not activate the WLan on Satellite L350D

  First of all, sorry for my bad English

  I'm having problems with the WIFI, I fail to enable it to connect to a wireless router and be able to connect to the internet

  Computers icon is green: if I choose: to built a connection or net and then I choose to connect to a router or wireless access point, I hit 'next' and then he said: "hardware detection and configuration of the net ' and then he said 'Windows don't detect any material NET Wireless' and he said ' to create a net wireless and flash configuration keeps in a usb unit»

  In the blue icon of a computer and like a ball behind: there is a screen called CONFIGFREE.

  If I press the 'radar' it says "this device net wireless is disabled." Enable the device"and if I touch" doctor conectivity, in ' "rolling / wan wireles ' State of the switch is enabled and the firewall is disabled.»

  But then, in the design, although it has two arrows. Blue disconnects and if I change the profile, it is said that the wire is not available and the realtek fast ethernet is available.

  Hello

  Your description is a bit confusing.
  So here are my Tips how to connect the laptop for WiFi using the Vista operating system.

  First check if your WiFi is turned on. You must use the key FN + F8 to go tot eh card WLan and then turn on the WLan switch on the side of the laptop.

  According to your WiFi (Atheros or Intel) card I advise to use a WLan configuration as Atheros Client Utility or Intel ProSet Utility tool.

  You can use these tools to configure WLan. I use one of these tools and I can connect and configure the WiFi network very easily.

  If you want to use the Vista WLan own configuration options, can access the network locations and right click on the WiFi connection.
  Choose then rebuilt Waln connection or something like that.
  Then choose your WLan which has been configured on the router WLan and put the right encryption settings and you should be able to connect to you wirelessly.

  Good bye

• Satellite Pro M70: Configfree and Wlan with WEP issue.

  I have a Satellite pro M70. With Configfree (v5.90.07), I can connect to the wireless network (with SSID) of my router and go to the internet. But when I put a WEP key in the router, and then I can not connect anymore.
  With Configfree, wireless Lan, I still can't see the network (with the name of the SSID, etc.) and I see that the network is secure. But I can't connect to the network more. This because the laptop adapter (Intel 2200BG) doesn t have the WEP key. My question is: How can I set the WEP key in Configfree? (A different key by different profiles).

  (Try to solve the problem I have downloaded the new Intel and IntelPROSET wireless drivers.) This live program asked the WEP key and makes a link without problem. Now with Configfree, Wireless LAN, I also see a connection (secured with WEP). But the rest of the Configfree program does more (CFMain.exe problem). I read in another topic that this is caused by the Intel program. You must remove this to solve the problem of Configfree. So this n t the solution.)

  My question is: How can I set the WEP key in Configfree? (A different key by different profiles).

  Hello

  Firstly the Toshiba Configfree program is not software for the WLan configuration.
  This program, you can use for the diagnostic procedure and it shows you the connection properties. But it of not possible to set the cipher with the Configfree.
  It seems that the IntelProset utility has a bad influence on the Configfree. The problem is that Toshiba doesn't support any 3rd party applications.

  Furthermore if this card doesn t WLan supports WEP encryption so you can not use it.
  WEP encryption, you can set in the WLan card properties.
  You also use the 3rd party WLan application like IntelProset or Atheros utility to configure the WiFi network but encryption depends on the WLan card not on the utility!

• Toshiba Software by disabling the automatic Wireless Configuration Service

  I have a problem with a Toshiba Satellite Pro laptop. When I start the system, the automatic Wireless Configuration Service is disabled and I have to go into Services and start physically whenever I start Windows (XP 32-bit sp3).

  I think it's own software of Toshiba (Q-Connect/Summit?) it prevents start automatically with Windows, because everything else is as it should be.

  Can you advise how to fix this so that the service always starts automatically and does not, during the trip, the settings for windows? Set up a wireless ad - hoc is quite difficult because there is no more headaches.

  See you soon,.

  John

  Hey Buddy,

  It s I don't know ConfigFree turns off this feature of Windows... As far as I know it s necessary service for all WLAN configuration tools

  Is manual start automatically, or simply the value type? You must assign it automatically.

  By the way: what laptop do you have?

• How to set up a WLAN connection?

  Hello!

  I'm new to this forum. I need help with a problem of wireless connection. I bought a Cardbus adapter for my Toshiba and I try to establish a wireless connection; my computer detects wireless (mine among them) but it won´t work.

  A message appears that says "windows won´t be able to connect to the selected network. I keep updating the list of networks, but the same thing happens all the time. I Don t know what to do.

  Can someone help me, please? Any idea?
  Thank you much in advance.
  Kind regards
  Beatriz

  Hello

  OK, it seems that you have properly installed the WLan card and everything directly in Device Manager.
  You have configured the router WLan? Do you have some cipher and/or filtering by mac address?
  Please check again!

  If you use the Wlan configuration option clean windows, you must verify the simple settings in network connections-> wireless network connection properties.

  New windows should appear and you should choose the wireless network tab.
  Please check if it use windows to configure my WiFi is marked. In the preferred networks field, you could add WLan network. Click on properties and you should be able to configure encryption.

• Satellite Pro M70: Unable to connect to the WLan with ConfigFree

  Salvation in the Forum.

  I have problems with a satellite Pro M70, about gaining control of wireless connections.

  When I scan with "The Radar" I have ConfigFree for available wireless accesspoints, I get several points available, but it is not able to connect to one of them. I can read their status and see their marker of WEP encryption.

  When I try to connect to one of them, I get a pop-up dialog, that said (translated from Danish) 'suppliers another software is in control of the wireless network card. When you try to configure a connection through the classic way to windows, windows States that "windows is not able to configure this wireless connection - if you have another program to manage wireless connections, you must use it". I guess it refers to ConfigFree...?

  Is the unnamed "other provider" associated Windows or perhaps associated McAfee (Security Suite 2007)?

  If you are familiar with this problem or something like that I'd be please to know.

  Also - where can I enter keys for WEP encryption for my friends in ConfigFree WLAN routers?

  > Trying to make a connection through the classic way to windows, windows States that "windows is not able to configure this wireless connection - if you have another program to manage wireless connections, you must use it". I guess it refers to ConfigFree...?

  It should not be a ConfigFree. According to you, an Intel ProSet utility or a Client Atheros wireless network adapter might be controls the Wlan configuration!

  Please check if one of the two control the WiFi network tools and turn off!

  > where can I enter keys for WEP encryption for my friends in ConfigFree WLAN routers

  You should have three different tabs in the utility Configfree.
  The second device settings provides the list of devices, and you should see the wireless network connection.
  Choose and use the button network connections.
  There you should find some encryption settings!

  Also check the profile settings tab and the option called security settings