IPSEC VPN is restarted

Similar Questions

• IPSEC VPN WRVS4400N

  Hi all

  We have a customer who has recently changed Vedors and came to us. We had to change the ISP and the need to make changes in their firewall. I went out on the site and has not been able to get into the routers and I contacted the previos company but they do not release this information. We have therefore had to reset devices and put everything up. Everything works great except before having an IPSEC VPN Tunnel between the 2 buildings. Both buildings have routers WRVS4400N and I configured a VPN IPSEC Tunnel on both sides. I named the same and the summary says that both are on the rise. But when I try to go from one side to the other, I am unable to Ping or solve anything. I'll put all the information I can find are relavent to this problem and hope someone can help me. I called Cisco, but they said they are out of warranty and will not be able to help. Cisco directed me here.

  Site A:

  Internal:

  192.59.1.1 (IP)

  255.255.255.0 (SN)

  External:

  96.10.218.14 (IP)

  255.255.255.252 (SN)

  96.10.218.13 (GW)

  24.25.5.60 (DNS1)

  24.25.5.61 (DNS2)

  

  Site b:

  I internal:

  192.39.1.1 (IP)

  255.255.255.0 (SN)

  External:

  50.52.145.50 (IP)

  255.255.255.252 (SN)

  50.52.145.49 (GW)

  184.16.4.22 (DNS1)

  184.16.33.54 (DNS2)

  

  
  

  V Tunnels PN

  Site has

  

  Site B

  

  For security purposes the IP addresses are not exactly what is displayed, but I checked 10 times and they correspond to the remote site said. Yet once again, say that they are on the rise, but I am unable to ping or see the tunnel devices. Help, please.

  Thanks in advance

  Mike

  The problem is most likely in the 'Local Group' configuration. How they are implemented is essentially to allow only the 192.39.1.1 and 192.59.1.1 talk to each other. These fields should be read as the subnet as this ID: 192.39.1.0 and 192.59.1.0

  Try this restart of the tunnels, and let us know how it worked.

• Support for L2TP/IpSec VPN on 1921

  Hello

  I am not able to find an answer on something very simple... Fact of 1921 Cisco router supports L2TP/IpSec VPN connections? (from Windows 7 clients)

  If she could please point me to the right location/document where I can read more about it.

  I already tried with the configuration below, but command ppp under a virtual-Template1 don't output interface.

  Thank you very much for your answers.

  Kind regards

  Herman

  # VPN configuration I've tried, but it did not work.

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  life 4000

  ISAKMP crypto key xxxxxxx address X.X.X.X (ip strongvpn)

  !

  !

  Crypto ipsec transform-set ESP-AES256-SHA1 esp - aes 256 esp-sha-hmac

  transport mode

  !

  Map 10 IPSEC L2TP ipsec-isakmp crypto

  defined peer X.X.X.X

  game of transformation-ESP-AES256-SHA1

  match address 101

  !

  !

  !

  Pseudowire-class pwclass1

  encapsulation l2tpv2

  local IP interface FastEthernet0/0

  PMTU IP

  !

  !

  !

  !

  interface FastEthernet0/0

  DHCP IP address

  automatic duplex

  automatic speed

  card crypto IPSEC L2TP

  !

  interface FastEthernet0/1

  IP 10.20.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  interface Serial0/0/0

  no ip address

  Shutdown

  !

  interface Serial0/1/0

  no ip address

  Shutdown

  2000000 clock frequency

  !

  virtual-PPP1 interface

  the negotiated IP address

  IP mtu 1399

  NAT outside IP

  IP virtual-reassembly max-pumping 64

  No cdp enable

  PPP authentication ms-chap-v2 callin

  PPP chap hostname vpnxxx

  PPP chap password 0 xxxxxxxxxx

  Pseudowire pw-class 1, pwclass1 X.X.X.X

  ##################################################################################################################

  Cisco-gw #show version

  Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.2 (4) M2, VERSION of the SOFTWARE (fc2)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2012 by Cisco Systems, Inc.

  Updated Thursday, November 7, 12 and 12:45 by prod_rel_team

  ROM: System Bootstrap, Version 15.0 M16 (1r), RELEASE SOFTWARE (fc1)

  Cisco-gw uptime is 2 days, 4 hours, 22 minutes

  System to regain the power ROM

  System restart to 09:11:07 PCTime Tuesday, April 2, 2013

  System image file is "usbflash0:c1900 - universalk9-mz.» Spa. 152 - 4.M2.bin.

  Last reload type: normal charging

  Reload last reason: power

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco CISCO1921/K9 (revision 1.0) with 491520K / 32768K bytes of memory.

  Card processor ID FCZ170793UH

  2 gigabit Ethernet interfaces

  1 line of terminal

  1 module of virtual private network (VPN)

  Configuration of DRAM is 64 bits wide with disabled parity.

  255K bytes of non-volatile configuration memory.

  249840K bytes of Flash usbflash0 (read/write)

  License info:

  License IDU:

  -------------------------------------------------

  Device SN # PID

  -------------------------------------------------

  * 0 CISCO1921/K9

  Technology for the Module package license information: "c1900".

  -----------------------------------------------------------------

  Technology-technology-package technology

  Course Type next reboot

  ------------------------------------------------------------------

  IPBase ipbasek9 ipbasek9 Permanent

  Security securityk9 Permanent securityk9

  given none none none

  Configuration register is 0 x 2102

  Yes, it is supported.

  http://www.Cisco.com/en/us/Tech/tk827/tk369/technologies_configuration_example09186a0080094501.shtml#iosforl2tp

  It is necessary to configure the encapsulation under virtual-model.

  Note: you will have much better results by using the IPSec VPN or SSL VPN client AnyConnect client.

• integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

  Hello

  I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

  Please help me, I need my VPN Thx a lot

  I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

• WRV200 ipsec VPN

  Hi guys,.

  Tried to set up an ipsec VPN LAN - LAN between my WRV200 and WRVS4400N my companion. Filled all the relevant config... simple... but still nothing. They don't seem to connect. We are both on ADSL and using IP address by DNS. Routers are in the log file and try to establish the connection. Tried all the setting, both routers are configured the same. STILL NO JOY! Can anyone help, before having to migrate to a netgear or something nasty!

  Sorry forgot to mention, using an AM200 modem in Bridge mode. It my router DHCP address direct WAN instead of NAT. The two systems are fixed the same where routers have outside the WAN address. The modem is transparent. I guess that NAT traversal in not required in that State.

• IPSec VPN to asa 5520

  Hello

  First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

  The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

  I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

  I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

  4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

  5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

  6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

  and this, in the journal of customer:

  Cisco Systems VPN Client Version 5.0.02.0090

  Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.1.2600 Service Pack 3

  24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

  Establish a secure connection

  26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "213.94.x.x".

  27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with 213.94.x.x.

  28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

  29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

  IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

  Set indicator established tunnel to register to 0.

  42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

  Can you see what I'm doing wrong?

  Thank you

  Sam

  Pls add the following policy:

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  You can also run debug on the ASA:

  debugging cry isa

  debugging ipsec cry

  and retrieve debug output after trying to connect.

• IPSec vpn - no selected proposal

  Hello:

  I am facing a problem in the configuration of the ipsec vpn on my 7200 router. It's a site to customer topology as shown below.

  

  The request from my pc, R2' isa crypto log:

  R2 #debug crypto isakmp
  Crypto ISAKMP debug is on
  R2 #.
  R2 #.
  R2 #.
  * 22:41:59.871 6 April: ISAKMP (0): received 66.66.66.52 packet dport 500 sport 500 SA NEW Global (N)
  * 22:41:59.879 6 April: ISAKMP: created a struct peer 66.66.66.52, peer port 500
  * 22:41:59.879 6 April: ISAKMP: new created position = 0x67E98D84 peer_handle = 0 x 80000002
  * 22:41:59.883 6 April: ISAKMP: lock struct 0x67E98D84, refcount 1 to peer crypto_isakmp_process_block
  * 22:41:59.887 6 April: ISAKMP: 500 local port, remote port 500
  * 22:41:59.891 6 April: ISAKMP: (0): insert his with his 67E5DCD8 = success
  * 22:41:59.911 6 April: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 22:41:59.911 6 April: ISAKMP: (0): former State = new State IKE_READY = IKE_R_MM1

  * 6 April 22:41:59.931: ISAKMP: (0): treatment ITS payload. Message ID = 0
  * 6 April 22:41:59.935: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.939: ISAKMP: (0): IKE frag vendor processing id payload
  * 6 April 22:41:59.939: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.943: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
  * 22:41:59.947 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
  * 6 April 22:41:59.947: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.951: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
  * 6 April 22:41:59.955: ISAKMP: (0): provider ID is NAT - T v2
  * 6 April 22:41:59.959: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.959: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
  * 6 April 22:41:59.963: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.967: ISAKM
  R2 #P: (0): provider ID seems the unit/DPD but major incompatibility of 241
  * 6 April 22:41:59.971: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.971: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
  * 6 April 22:41:59.975: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.979: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
  * 22:41:59.983 6 April: ISAKMP: (0): pair found pre-shared key matching 66.66.66.52
  * 6 April 22:41:59.987: ISAKMP: (0): pre-shared key local found
  * 22:41:59.987 6 April: ISAKMP: analysis of the profiles for xauth...
  * 22:41:59.991 6 April: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 10
  * 22:41:59.995 6 April: ISAKMP: AES - CBC encryption
  * 22:41:59.995 6 April: ISAKMP: keylength 256
  * 22:41:59.999 6 April: ISAKMP: SHA hash
  * 22:41:59.999 6 April: ISAKMP: unknown group of DH 20
  * 22:41:59.999 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.003 6 April: ISAKMP: type of life in seconds
  * 22:42:00.003 6 April: ISAKMP:
  R2 # life expectancy (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 2 against the policy of priority 10
  * 22:42:00.011 6 April: ISAKMP: AES - CBC encryption
  * 22:42:00.011 6 April: ISAKMP: keylength 128
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group unknown 19
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 3 against the policy of priority 10
  R2 #r 6 22:42:00.011: ISAKMP: AES - CBC encryption
  * 22:42:00.011 6 April: ISAKMP: keylength 256
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 4 against the policy of priority 10
  * 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): offered hash algorithm is
  R2 # does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform against the policy of priority 10 5
  * 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: group by default 2
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.015 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.019 6 April: ISAKMP: (0): offered hash algorithm does not match policy.
  * 22:42:00.023 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 0
  * 22:42:00.023 6 April: ISAKMP: (0): no offer is accepted!
  * 6 April 22:42:00.027: ISAKMP: (0): phase 1 SA policy is not acceptable! (local 180.180.0.130 remote 66.66.66.52)
  * 22:42:00.027 6 April: ISAKMP (0): increment the count of errors on his, try 1 of 5: construct_fail_ag_init
  * 6 April 22:42:00.027: ISAKMP: (0): has no
  R2 #construct AG information message.
  * 6 April 22:42:00.027: ISAKMP: (0): lot of 66.66.66.52 sending my_port 500 peer_port 500 (R) MM_NO_STATE
  * 22:42:00.027 6 April: ISAKMP: (0): sending a packet IPv4 IKE.
  * 22:42:00.031 6 April: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 22:42:00.035 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): IKE frag vendor processing id payload
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
  * 22:42:00.039 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID is NAT - T v2
  * 6 April 22:42:00.039: ISAKMP: (0)
  R2 #: load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 241
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
  * 22:42:00.039 6 April: ISAKMP (0): action of WSF returned the error: 2
  * 22:42:00.039 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  * 22:42:00.039 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

  * 22:42:00.059 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
  * 22:42:00.059 6 April: ISAKMP: unlock counterpart struct 0x67E98D84 for isadb_m
  R2 #ark_sa_deleted (), count 0
  * 22:42:00.067 6 April: ISAKMP: delete peer node by peer_reap for 66.66.66.52: 67E98D84
  * 22:42:00.071 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 22:42:00.075 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_DEST_SA

  * 22:42:00.087 6 April: ISAKMP: (0): removal of HIS right State 'No reason' (R) MM_NO_STATE (post 66.66.66.52)
  * 22:42:00.087 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_ERROR
  * 22:42:00.087 6 April: ISAKMP: (0): former State = new State IKE_DEST_SA = IKE_DEST_SA

  * 22:42:00.895 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
  * 22:42:02.911 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
  R2 #.
  * 22:43:00.087 6 April: ISAKMP: (0): serving SA., his is 67E5DCD8, delme is 67E5DCD8
  R2 #.

  And when I capture on my pc, I got:

  

  I don't know why, waiting for you helps nicely, thank you very much!

  I think that what is wrong is your combination of your group of encryption, hashing and dh, try changing your sha instead of md5 hash table.

• Routing access to Internet through an IPSec VPN Tunnel

  Hello

  I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.

  I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.

  Any help would be greatly appreciated.

  Thank you.

  Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.

• SA520 and Question IPSec VPN RVS4000

  Hello

  I installed an IPSec VPN for one of my friends for his company. At its principal office, I installed a Cisco SA520 and he uses to connect devices such as the iPhone and iPad via the IPSec VPN. He uses this fact because he travels abroad a lot and he has problems with services such as Skype is blocked in some countries. This configuration works very well.

  It also has a Cisco RVS4000, which he would like to install at his place of business to the Mexico. He would like the RVS4000 VPN configuration to the SA520 in his office. The SA520 in his office has a static IP address. The RVS4000 to the Mexico does not work.

  Is it possible to Setup IPSec VPN between a SA520 with a static IP and RVS4000 address that does not have a static IP address? If so, examples of configuration would be greatly appreciated.

  Thank you!

  Hi William, simply sign up for a dyndns account or similar service, the RVS4000 configuration will be the same, instead of the IP, you'd be using the dyndns name.

  -Tom
  Please mark replied messages useful

• Is availble for IPsec VPN FOS 6.3 support stateful failover

  Is availble for IPsec VPN FOS 6.3 support stateful failover

  SAJ

  Hello Saj,

  Unfortunately not... stateful failover replica information such as:

  Table of connection TCP, udp xlate table ports, h.323, PAT port allocation table...

  they replicate data such as:

  user authentication (uauth) table

  Table ISAKMP / IPSEC SA

  ARP table

  Routing information

  Therefore, in the case where the main breaks down, the IPSEC vpn will be reformed for the failover... Meanwhile, the user will not be able to access the applications...

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• ISA500 site by site ipsec VPN with Cisco IGR

  Hello

  I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

  But without success.

  my config for openswan, just FYI, maybe not importand for this problem

  installation of config

  protostack = netkey

  nat_traversal = yes

  virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

  nhelpers = 0

  Conn rz1

  IKEv2 = no

  type = tunnel

  left = % all

  leftsubnet=192.168.5.0/24

  right =.

  rightsourceip = 192.168.1.2

  rightsubnet=192.168.1.0/24

  Keylife 28800 = s

  ikelifetime 28800 = s

  keyingtries = 3

  AUTH = esp

  ESP = aes128-sha1

  KeyExchange = ike

  authby secret =

  start = auto

  IKE = aes128-sha1; modp1536

  dpdaction = redΘmarrer

  dpddelay = 30

  dpdtimeout = 60

  PFS = No.

  aggrmode = no

  Config Cisco 2821 for dynamic dialin:

  crypto ISAKMP policy 1

  BA aes

  sha hash

  preshared authentication

  Group 5

  lifetime 28800

  !

  card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

  !

  access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

  !

  Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

  crypto dynamic-map DYNMAP_1 1

  game of transformation-ESP-AES-SHA1

  match address 102

  !

  ISAKMP crypto key address 0.0.0.0 0.0.0.0

  ISAKMP crypto keepalive 30 periodicals

  !

  life crypto ipsec security association seconds 28800

  !

  interface GigabitEthernet0/0.4002

  card crypto CMAP_1

  !

  I tried ISA550 a config with the same constelations, but without suggesting.

  Anyone has the same problem?

  And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

  I can successfully establish a tunnel between openswan linux server and the isa550.

  Patrick,

  as you can see on newspapers, the software behind ISA is also OpenSWAN

  I have a facility with a 892 SRI running which should be the same as your 29erxx.

  Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

  Here is my setup, with roardwarrior AND 2, site 2 site.

  session of crypto consignment

  logging crypto ezvpn

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 2

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 4

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 5

  BA 3des

  preshared authentication

  Group 2

  life 7200

  ISAKMP crypto address XXXX XXXXX No.-xauth key

  XXXX XXXX No.-xauth address isakmp encryption key

  !

  ISAKMP crypto client configuration group by default

  key XXXX

  DNS XXXX

  default pool

  ACL easyvpn_client_routes

  PFS

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

  !

  dynamic-map crypto VPN 20

  game of transformation-FEAT

  market arriere-route

  !

  !

  card crypto client VPN authentication list by default

  card crypto VPN isakmp authorization list by default

  crypto map VPN client configuration address respond

  10 VPN ipsec-isakmp crypto map

  Description of VPN - 1

  defined peer XXX

  game of transformation-FEAT

  match the address internal_networks_ipsec

  11 VPN ipsec-isakmp crypto map

  VPN-2 description

  defined peer XXX

  game of transformation-FEAT

  PFS group2 Set

  match the address internal_networks_ipsec2

  card crypto 20-isakmp dynamic VPN ipsec VPN

  !

  !

  Michael

  Please note all useful posts

• Problem with IPSec VPN ISA500 & login questions (multiple devices)

  I have a Cisco ISA500, we use for connection with IPSEC VPN of some products apple (MacBook Pro and iPad). We can operate randomly once in a while, but it fails most of the time of negotiation. Someone at - it suggestions on what I can do to make this work?

  I did test it on my Linux machine and it does not when I had configured default settings. I had to change the NAT Traversal for UDP CISCO on the Linux machine for the connection to work.

  14/04/03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
  2014-04-03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
  2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
  2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Dead Peer Detection]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Cisco-Unity]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [XAUTH]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Dead Peer Detection]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Cisco-Unity]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [XAUTH]; (pluto)

  Hi rich,

  What version of firmware you used before upgrade?  You upgrade to 1.2.19 and now this works?

  Thank you

  Brandon

• Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

  Hi all

  I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941.  I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here.  Have I not IOS bad? I thought that a picture of K9 would do the trick.

  Any suggestions are appreciated

  That's what I get:

  Router (config) #crypto?
  CA Certification Authority
  main activities key long-term
  public key PKI components

  SEE THE WORM

  Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Updated Thursday, March 10, 10 22:27 by prod_rel_team

  ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

  The availability of router is 52 minutes
  System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
  System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
  Last reload type: normal charging
  Reload last reason: reload command

  This product contains cryptographic features...

  Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
  Card processor ID FTX142281F4
  2 gigabit Ethernet interfaces
  2 interfaces Serial (sync/async)
  Configuration of DRAM is 64 bits wide with disabled parity.
  255K bytes of non-volatile configuration memory.
  254464K bytes of system CompactFlash ATA 0 (read/write)

  License info:

  License IDU:

  -------------------------------------------------
  Device SN # PID
  -------------------------------------------------
  * 0 FTX142281F4 CISCO1941/K9

  Technology for the Module package license information: "c1900".

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Configuration register is 0 x 2102

  You need get the license of security feature to configure the IPSec VPN.

  Currently, you have 'none' for the security feature:

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Here is the information about the licenses on router 1900 series:

  http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html

• IP address of the IPSec VPN client did not get distributed via EIGRP

  We use an ASA for VPN remote access. He is running EIGRP redistribute static routes. When a client Anyconnect SSL connects, the SAA creates a static route for this client, and it gets redistributed via EIGRP. When an IPSec VPN client connects, the SAA creates a static route for this customer, but he isn't redisributed via EIGRP and so the client can not achieve anything. Why he would distribute a static created by an IPSec client?

  Thank you

  Have you set up IPP on dynamic Cryptography?

• Cisco RV220W IPSec VPN problem Local configuration for any config mode

  Dear all,

  I need help, I am currently evaluating RV220W for VPN usage but I'm stuck with the config somehow, it seems that there is a problem with the Mode-Config?

  What needs to be changed or where is my fault?

  I have installed IPSec according to the RV220W Administrator's Guide. Client's Mac with Mac Cisco IPSec VPN, I also tried NCP Secure Client.

  I have 3 other sites where the config on my Mac works fine, but the Cisco VPN router is not.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: remote for found identifier "remote.com" configuration

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: application received for the negotiation of the new phase 1: x.x.x.x [500]<=>2.206.0.67 [53056]

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: early aggressive mode.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: RFC 3947

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsec-nat-t-ike-02

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: CISCO - UNITY

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: DPD

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: for 2.206.0.67 [53056], version selected NAT - T: RFC 39472013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: floating ports NAT - t with peer 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload is x.x.x.x [4500]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload does not match for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT detected: Peer is behind a NAT device

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: request sending Xauth for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association established for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REPLY" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: connection for the user "Testuser".

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REQUEST" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: ignored attribute 5

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28678

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28683

  2013-03-07 01:56:07: [CiscoFirewall] [IKE] INFO: purged-with proto_id = ISAKMP and spi = 1369a43b6dda8a7d:fd874108e09e207e ISAKMP Security Association.

  2013-03-07 01:56:08: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association deleted for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  Hi Mike, the built-in client for MAC does not work with the RV220W. The reason is, the MAC IPSec client is the same as the Cisco VPN 5.x client.

  The reason that this is important is that the 5.x client work that on certain small business products include the SRP500 and SA500 series.

  I would recommend that you search by using a client VPN as Greenbow or IPSecuritas.

  -Tom
  Please mark replied messages useful