IPv4 address default of SX - 80

Just bought two devices conference SX-80 (without distance, without touch screen) and I'm trying to find out if there is the default IPv4 address to enter the web configuration page.  Is this one?  What is it?

If there is no default, an a local DHCP server can assign? that is DHCP is defined as the default value?

What screen exactly the SX80 was not sitting at?

Try to set the following option in the configuration of the codec, it defines how key signs that the codec should expect to be connected.

Peripherals Profile TouchPanels: 0

Tags: Cisco Support

Similar Questions

  • problem with windows 7 starter Autoconfiguration IPv4 address and IPv4 address

    I can not change or disable Autoconfiguration IPv4 address in the ipconfig-all command

    I can't connect to the network any ip iput ditect as duplicate.

    can anyone help?

    ipconfig-all

    Windows IP configuration

    Name of the host...: xxx - PC
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Ethernet connection to the Local network card:

    The connection-specific DNS suffix. :
    Description...: Realtek RTL8168B/8111 Family PCI - E Gigab b
    It Ethernet NIC (NDIS 6.20)
    Physical address.... : 00-50-DB-00-15-2E
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    Autoconfiguration IPv4 address. . : 169.254.242.251 (Duplicate)
    ... Subnet mask: 255.255.0.0.
    IPv4 address...: 192.168.20.155 (Duplicate)
    ... Subnet mask: 255.255.255.0.
    ... Default gateway. :
    NetBIOS over TCP/IP...: enabled

    Tunnel adapter isatap. {F0C7F7B4-DF88-4908-A9C1-F8B888710CAC}:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Microsoft ISATAP adapter
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Hello

    If a computer is only connected to a switch, the automatic configuration is not valid.

    Autoconfiguration applies when a computer is connected to a server that can provide the configuration.

    Wireless routers have a DHCP server that provides a valid IP address.

    Ordinary switch is a transparent network device that cannot provide any configuration.

    When there is no DHCP server, the computer must be configured with a static IP address.

    Look at this page, http://blog.mclaughlinsoftware.com/2009/11/26/windows-7-static-ip/

    Follow the path as described in step 5 (Do not pay attention to specific numbers, your number is to be determined in accordance with your network plan).

    Maybe you want to provide an explanation of what you are trying to reach.

    Jack-MVP Windows Networking. WWW.EZLAN.NET

  • SGE2000P loses the manually configured ipv4 address after reboot

    I am setting up a new switch SGE2000P as independent. As part of the Setup, I need to assign a new IPV4 address to the switch default instead a 192.168.1.254. After that I applied the changes everything works fine, but when the reboot of the switch get the ip address back to the default. Any contributions to this issue will be appreciated.

    Elkins

    Hello Evillalona,

    I just looked at the issue you are seen and wanted to check with you on this subject.

    When you change the settings in the switch then go to the file management section

    the switch and make a copy of the running configuration to the startup configuration? I just wanted to

    check and see if that would fix the problem you are experiencing. I've heard other people with

    the same problem and that was the difficulty for them.

    Thank you

  • HP LaserJet P1102p / IPv4 address & mask subnet IP changed by mistake

    Dear Sir.

    Am mentioned above tobic, I changed the (IPv4 address) and more (IP subnet mask) by mistake and now I can not open the integrated Web server. In addition, wireless printing no longer because of the change of address IPv4. I need the steps of reconfiguring address IPv4 to back as before.

    name of the printer: HP LaserJet P1102p

    old IPv4 address: 192.168.1.66

    current IPv4 (as indicated in the configuration of the device page) address: 8.8.8.8

    previous IP subnet mask: 255.255.255.0

    subnet mask current IP (as indicated in the configuration of the device page): 0.0.0.0

    Please note that the defult IP gateway is still the same as before.

    I need only to know the way how to reconfigure the two IP addresses?

    Thank you...

    Hello

    Reset the network settings on the unit by turning off the printer.

    While now the buttons cancel and Wireless switch on the printer. as soon as the light starts flashing, you can release the keys.

    Run the installation of the software on your computer by selecting to reconnect it to your Wi - Fi network.

    Once the printer connects to your network, you can set custom again values.

    Shlomi

  • Dynamic DNS update of IPv4 addresses does not not in Windows 7

    Several months ago, we noticed behaviors incompatible with Windows 7 clients and their entry in DNS Active Directory.

    The main problem is that our Windows 7 clients only will be not systematically their IPv4 address in Active Directory DNS by using dynamic DNS (RFC2136)

    Initial question:

    • A handful of customers will register its IPv4 address, but it is a minority and most don't (this is the main question)
    • We use the public IP address space.
    • Customers have been constantly recording the IPv6 address for 6to4 in DNS card but not its IPv4 address.

    We have disabled the 6to4 map by using Group Policy, because we do not use IPv6 and don't plan to use the 6to4 transition.

    Secondary issue:

    • Customers is no longer recording card 6to4 in DNS (good)
    • Majority of customers do not yet record their (bad) IPv4 address.

    What I've checked so far:

    • Analysis using Wireshark:

      • Most clients make no request for SOA record and therefore do not try to send dynamic DNS updates.
      • Some customers get the AD zone SOA record and then send the DNS dynamic update to one of the DCs.
      • I see nothing of clearly different on clients who send updates and those who are not.
      • All the other AD related traffic, for example request/response for domain/ldap SRV record looks normal.
    • Settings on the client:

      • The IPv4 adapter "save addresses for this connection in DNS" checked.
      • The primary DNS suffix is the same as our AD domain name.
      • The AD domain name is a COMPLETE domain name.
      • Use us group policy to apply the primary DNS suffix and some connection specific suffixes.
      • Customers do everything they are supposed to; as access to shared resources, printers, etc. - just not update DNS.

    I read all of the following, but I'm no further forward:

    DNS of processes and Interactions

    https://TechNet.Microsoft.com/en-us/library/dd197552 (v = ws.10) .aspx

    Understanding dynamic update

    https://TechNet.Microsoft.com/en-us/library/cc771255 (v = ws.11) .aspx

    Does anyone have ideas/tools/scripts which may be able to progress my troubleshooting?

    Darren.

    This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
    If you give us a link to the new thread we can point to some resources it

  • can I configure an IPv4 address and IPV6 on the same NETWORK card

    I test double stack IPv4 and IPv6 on a firewall.  Can I configure IPv4 and IPv6 addresses on the same NETWORK card using a laptop installed with Windows 7, in order to test the firewall for both IPv4 and IPv6 protocols access? And if so, how to configure the NETWORK card?

    Thank you

    Jack P.

    See what...

    http://Windows.Microsoft.com/en-us/Windows7/change-TCP-IP-settings

  • Get a strange IPv4 address of the DHCP server

    Hi all

    As title, I got a strange IP - DHCP server 169.254.XXX.XXX.

    I used Wireshark, tried to get the bootp packets.  I found that my laptop 169.254.xxx.xxx used as source address to send DHCP Discover.

    In addition, there is an option called content with 169.254.xxx.xxx requested ip address. Like my source address.

    I couldn't access the Internet with this IP address.

    I was wondering, is that it is a normal behavior for windows 7 to use 169.254.xxx.xxx to send DHCP Discover?

    A DHCP request is sent through the universal 255.255.255.255 broadcast address which is one of the addresses that a server is listening. The query includes the MAC address of the applicant unit because at this point, it doesn't have an IP address. The DHCP server responds to the MAC address in order to assign the address.

    In your case, the range 169.254 is called the APIPA address and the PC actually assigns to himself because he did not see a response from the DHCP server. As you refer to Wireshark having a reading of the present.

    http://wiki.Wireshark.org/APIPA

    The customer may not send the request via this address and get a response because the DHCP server is not listening on the address or by using the range. The answer must be done via the Mac.

  • CSCuj85494 - Auth message logging display IPv4 address as 91; Source UNKNOWN & #93;

    Hello

    We have improved 4948 to 15.0.2 - SG9 Mexit D (ENTERPRISE SERVICES SSH).

    but this issue remains on this version?

    What is the workaround?

    Problem is solved under 15.0 (2) SG6, later versions suffer from this bug.

    06:09:16.395 Oct 9: % SEC_LOGIN-5-LOGIN_SUCCESS: success of the connection [user: xxxx] [Source: 0.0.0.0] [localport: 0] to 06:09:16 UTC Friday, October 9, 2015

  • Unavailable PIM event if the option "send using the ' has the value other than the default email address

    Hi all

    I have more than two e-mail set up on my BlackBerry (OS 4.5) and define a default my BB email address.

    now, if I create a new event in the native calendar application set option "send to" to my other email address (default no).

    in my application I m going to the EventList

    (EventList) PIM.getInstance () .openPIMList (PIM. EVENT_LIST, PIM. READ_WRITE);

    This list contains only the events in which the option ' send to ' is set to my default email address.

    What is the normal behavior of the PIM EventList?

    Thank you

    Gerard

    Each email address has its own calendar, which has its own EventList.  You can use the PIM.listPIMLists method to get a list of all events lists.  This feature was added in version 4.6.0 API of BlackBerry set.

  • address IPv4 in Windows 7

    What is the IPv4 address?

    http://en.Wikipedia.org/wiki/IPv4

  • Address conflict IP TC and iMac

    Is back from vacay to an IP conflict on my mid 2007 iMac error message. My TC Airport caught the iMac IP and will not let go. Any other device on the network wireless can enter an IP address. We have AppleTV, iPhone, iPad, even a G5 which are humming and I'm dead in the water. Cannot use a static IP address to circumvent the problem, as I previously for other problems. I'm under El captain now 10.11.5 I rebooted all dozens of times, even deleted my AirPort Extreme Extender to eliminate as a possible source of problems. My ISP don't touch anything Macintosh, but they confirmed with other devices running, it must be the iMac. I tried to change the password on the TC so that any unauthorized connection would fall, but failed. Do I have to reset the TC? If I do I will lose my backups? The iMac and the G5 were both using the TC for backups.

    My TC Airport caught the iMac IP and will not let go.

    Try the following to release and refresh the IP address provided to your iMac to the Time Capsule (TC):

    • System Preferences > network > Wi - Fi > advanced > TCP/IP tab
    • Note the value for the IPv4 address
    • Click on the button "renew the DHCP lease.
    • Again, check the value of the IPv4. It changed?

    You should not have to reset the TC to solve this problem... but if you do, any of the types of discount to zero (soft, hard, or default) will erase all the data on the internal drive of the TC or any drive connected to its USB port.

  • OfficeJet Pro 8000: installation of the driver wireless Officejet 8000 Pro says default gateway is 0.0.0.0

    I'm chasing a well-documented problem of my printer lost network connection after a variable period of printing to do not. The only way to connect is to change the power supply, but the printer may take 5 minutes to blow and grunts until it settles and prints...

    I put a static IP address on the printer (10.0.0.250) as well as an empty default gateway successfully, and the documents are printed after 5mins of blowing and grunting (save the regular lost connection which I'm hunting...).

    I put what I thought has a static IP address on the router to match (see image below), but now I don't know if it was necessary, and if the 'hosting of the fixed DHCP server' is correct. It might be useless and missleading...

    Using the configuration of the printer to 10.0.0.250 interface, it seems to accept the installation of the network when the default gateway is blank. With the help of 10.0.0.2 caused the 'page not found' error in my browser (Chrome).

    However, when you try to reinstall the drivers, the installer has grumbled to the default gateway is set to 0.0.0.0, which currently is the only way it will work...

    The Win7 PC is plugged into the router.
    The printer wireless to the router.

    ipconfig on the pc gives Ethernet card details below.

    So basically I have no idea what I'm doing...!

    ==============

    Ethernet connection to the Local network card:

    The connection-specific DNS suffix. :
    Link-local IPv6 Address...: fe80::c8e1:63ef:85e0:7 24% 13 c.
    IPv4 address...: 10.0.0.249
    ... Subnet mask: 255.255.255.0.
    ... Default gateway. : 10.0.0.2.

    Router config.

    Thank you for your comments. It seems that I solved the problem of the default gateway. Time will tell if the remains of the printer connected through long periods of no use (see update below).

    It seems that the configuration of the router of the "DHCP fixed existing host" has nothing to do with the device assigned a static IP address. In fact, it seems that this setting prevents the printer through a default gateway of the router address.

    I noticed that when you give the PC a fixed IP, it connected through the router without any other configuration of router. If I reasoned that it may be applied to the printer also, so I moved the printer 10.0.0.251 and Bingo! the default gateway can be set to the IP address of the route.

    Since then I downloaded to other updates, which is supposed to correct the common problem of wireless printers, loss of the connection.

    I'll try to report in the next few weeks an update about the stability of connection network printers.

    UPDATED: May 23, 2016

    And more of the foregoing, my router support suggested I increase a parameter "timeout" from 24 hours to 10 days. I did it more than a week. Today, the printer worked after the impression of not for about 5 days

  • Browser does not accept the IP address?

    I recently had to reset my wrt54g2 v1 router.  I'm currently trying to secure my network, but when I enter my IP address in my browser, it does not connect.  I tried to enter my IPv4, my default gateway, 192.168.1.1 and 192.168.0.1 and none of them works.  Help?

    Hello

    You wired or wireless connected to the router? Just to make sure, temporarily connect a cell phone to one of the ports numbered on the back of your router. Check your connection details (IPv4, DNS and default gateway address), then make sure that you receive these details with the automatic configuration (DHCP). With a stable powerlight, try to access the router configuration page using the default gateway.

  • Default gateway disappears after installing SP2.

    Hi people

    I just installed SP2, and now when I start/restart the computer, the default gateway is missing. When I check the properties of the connection, the IP address is correct, but the default gateway is blank - it does not 0.0.0.0, there is nothing at all.

    My computer (Vista Ultimate x 86) and a XP Pro PC are connected to a router. I have disabled the DHCP on the router and use a static IP address for each computer. The XP machine is rarely used. I also have a configuration of the VPN connection. When I first encountered this problem, I deleted the VPN connection in case the PC tried to use it to connect to the Internet. I later recreated once I realized what the problem was.

    Even if I can reset the bridge, I don't want to have to do this every time that I reboot.

    **************************************

    ipconfig on my Vista PC at startup:

    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

    C:\Windows\System32>ipconfig/all

    Windows IP configuration

    Name of the host...: OS
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Ethernet connection to the network space 2 card:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Bluetooth PAN network adapter
    Physical address.... : 00-11-67-AA-AC-D3
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Ethernet connection to the Local network card:

    The connection-specific DNS suffix. :
    ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ether
    Net controller
    Physical address.... : 00-1E-8C-B7-D9-76
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::980c:2d5d:1cd3:4195% 10 (Preferred)
    IPv4 address: 192.168.1.100 (Preferred)
    ... Subnet mask: 255.255.255.0.
       ... Default gateway. :
    DHCPv6 IOOKING...: 251666060
    DHCPv6 DUID customer...: 00-01-00-01-0F-F2-6D-55-00-1E-8C-B7-D9-76

    DNS servers...: 192.168.1.254
    NetBIOS over TCP/IP...: enabled

    Card tunnel Local Area Connection * 6:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {9E323F18-CB91-4524-B5E3-64A8C101B
    078}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 7:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 02-00-54-55-4E-01
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 17:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {5A583DB0-C514 - B 49, 6 - 9D1A - 2703884-6
    AFB}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    C:\Windows\System32 >

    **************************************
    **************************************

    After resetting the gateway:

    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

    C:\Windows\System32>ipconfig/all

    Windows IP configuration

    Name of the host...: OS
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    Ethernet connection to the network space 2 card:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Bluetooth PAN network adapter
    Physical address.... : 00-11-67-AA-AC-D3
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Ethernet connection to the Local network card:

    The connection-specific DNS suffix. :
    ... Description: Marvell Yukon 88E8056 PCI-E Gigabit Ether
    Net controller
    Physical address.... : 00-1E-8C-B7-D9-76
    DHCP active...: No.
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::980c:2d5d:1cd3:4195% 10 (Preferred)
    IPv4 address: 192.168.1.100 (Preferred)
    ... Subnet mask: 255.255.255.0.
       ... Default gateway. : 192.168.1.254
    DHCPv6 IOOKING...: 251666060
    DHCPv6 DUID customer...: 00-01-00-01-0F-F2-6D-55-00-1E-8C-B7-D9-76

    DNS servers...: 192.168.1.254
    NetBIOS over TCP/IP...: enabled

    Card tunnel Local Area Connection * 6:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {9E323F18-CB91-4524-B5E3-64A8C101B
    078}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 7:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 02-00-54-55-4E-01
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 17:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {5A583DB0-C514 - B 49, 6 - 9D1A - 2703884-6
    AFB}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    C:\Windows\System32 >

    **************************************

    Can someone tell me what is the cause, please? I would also appreciate it if someone can tell me how I can configure the default gateway by using a batch file executed with administrator privileges. That would save me having to dig through Control Panel etc etc every time my computer starts.

    Thank you!

    Hi RealBlood,
    Thank you for visiting the Microsoft Answers forum.
    To solve your problem follow these steps:

    Repair options for TCP/IP stack for use with Windows Vista.

    Start, Programs\Accessories and right click on command prompt, select "Run as Administrator" to open a command prompt.

    In the command prompt window that opens, type type the following commands:

    Restore the default install WINSOCK entries: netsh winsock reset catalog

    Reset the battery TCP/IP IPv4 default installation. netsh int ipv4 reset reset.log

    Reset the battery TCP/IP IPv6 default installation. netsh int ipv6 reset reset.log

    Reboot the computer.

    Reset the default router by pressing the reset for 15 seconds with power button.

    • Turn off everything, modem, router, computer.
    • Connect the modem to the WAN/Internet port on the router.
    • Connect the computer to one of the router's LAN/network ports.
    • Turn on the modem, wait for triggering connect light.
    • Turn on the router, wait two minutes.
    • Start the computer.

    When the computer is completely loaded, we will see that.

    Hold down the Windows key and press R, then type CMD to open a command prompt:

    In the command prompt window that opens, type type the following command:

    IPCONFIG/ALL

    Right click in the command window and choose select all, and then press enter.
    Paste the results in a message here.

    Martin
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • The ip address of my router cannot be obtained by my cell phone, but he can get other computers. How can I solve the problem?

    Here is the ipconfig/all command information.

    C:\Windows\System32>ipconfig/all

    Windows IP configuration

    Name of the host...: owner-PC
    Primary Dns suffix...:
    Node... type: hybrid
    Active... IP routing: No.
    Active... proxy WINS: No.

    WirelessLAN adapter Wireless Network Connection:

    The connection-specific DNS suffix. :
    ... Description: Intel(r) WiFi Link 5100 AGN
    Physical address.... : 00-1E-65-05-FA-DC
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes
    Address IPv6 local link...: fe80::e582:a22f:fef5:c1af % 11 (Preferred)
    Autoconfiguration IPv4 address. . : 169.254.193.175 (Preferred)
    ... Subnet mask: 255.255.0.0.
    ... Default gateway. :
    DNS servers: fec0:0:0:ffff:1 1%
    FEC0:0:0:FFFF:2 1%
    FEC0:0:0:FFFF:3 1%
    NetBIOS over TCP/IP...: enabled

    Local of EthernetAdapter network connection:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    Description...: Realtek RTL8102/8103 PCI-E FE Family NETWORK map
    Physical address.... : 00-23-5A-0D-E6-2A
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 7:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {D57EF487-9E9D-4432-A3F6-09941DBAC
    B 9, 7}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 11:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Card 6TO4
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 12:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 02-00-54-55-4E-01
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 13:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {82CD5F3A-4FE2 - 41 D 2 - 9313-09635 C 287
    3A 1}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    0

    Maybe this can help.

    These steps and tell us where is the breaking point.

    Check the Device Manager for the wireless card valid entry.

    http://www.ezlan.NET/Win7/net_dm.jpg

    If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

    Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

    http://www.ezlan.NET/Win7/net_connection_tcp.jpg

    ------------------

    The wireless card drivers much also install utility wireless of the seller.

    Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

    ----------------

    Make sure you firewall No. preventing / blocks wireless components to join the network.

    Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

    If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

    party like Hello and NetMagic 3rd network managers can block local traffic too.

    ---------------------------

    Stack TCP/IP work should look like.

    Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

    http://www.ezlan.NET/Win7/status-NIC.jpg

    Description is the data of the card making.

    The physical address is MAC of the card number.

    The xx must be a number between 0 and 255 (all xx even number).

    YY should be between 0 and 255

    ZZ should be between 0 and 255 (zz all the same number.)

    The date of the lease must be valid at the present time.

    * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

    * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

    ---------------------------------------------------

    A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

    Above everything is OK, you must be able to connect to the router.

    Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

    If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

    Enable security wireless after you eat to make a functional connection.


    Jack-MVP Windows Networking. WWW.EZLAN.NET

Maybe you are looking for

  • A9S02PA #ABG: can I upgrade my pavilion g6 ph - 1310AX

    Hello Im trying to work if I can upgrade my CPU on my ph pavilion g6 - 1310AX and if that is one of the highest I can put in my current system. Any help would be greatly appreciated

  • Convert Labview 8.6 Labview 8.5

    Hello Could someone please convert these files (skypesdk) in labview 8.6 version to version 8.5? I have test the sdk 1.0 Skype version, he has a great job and need this for my college project 1.0.1... Thx a lot for your help. Oli

  • Problem with Windows Media Player and MTS to video clips

    When I load my video files MTS (AVCHD) of my Canon Vixia HFS100 camcorder to my PC and try to open and view them in Windows Media Player, I can hear the sound but I do not see the video. What can I do to fix it so I can not see the video?

  • image of Hotmail e-mail is not visible

    Hello, I have windows vista and new firefox 6.0... When I want to put an image in an email, I right click on the photo, copy, then go to email and paste into the body of the mail... you can see the perfect image... but the problem is when I hit the S

  • where can I download HP Recovery Manager?

    I have a HP Pavilion A520n. I replaced the hard drive and need to replace the Recovery Manager software to get back where he was. I need to get the HP Recovery Manager download, ideas? No available at HP recovery disk! Windows XP Home Edition has on