Similar Questions

• Trend Micro deep Security supported with Vmware

  Trend Micro deep Security supported with Vmware

  Hi Sylvie,.

  Please see the compatibility matrix please let me know if that helps

  http://eSupport.trendmicro.com/solution/en-us/1060499.aspx

• ISCSI LUN can support backup VMWare Consolidation?

  Dear all,

  ISCSI LUN can support backup VMWare Consolidation?

  Could help you find some documents for this?

  Thank you

  Dennis Dai

  see page 22 of http://www.vmware.com/pdf/vi3_35/esx_3/r35u2/vi3_35_25_u2_vm_backup.pdf

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• CUCM 8.5.1 with vmware ESXi 5 on UCS C250 M2 supported?

  Hi all.

  My name is Shin Jcob.

  I'm Korean.

  So I can't speak English.

  But I have question and I want to know this information.

  Now, my client use the CUCM 8.5.1 with vmware ESXi5 UCS C250 m2.

  Unfortunately, it was to issue. T.T

  Problem is error Vmware host.

  Error message is I/O latency.

  But I have my doubts C250 M2.

  Because I tried to find the CUCM 8.5.1 with C250 not manage the text but I couldn't it.

  Maybe if you know, then answer me.

  Thank you very much for reading my poor English text.

  Have you already reviewed the wiki of virtualization?

  UC in a virtualized environment

  http://docwiki.Cisco.com/wiki/Unified_Communications_in_a_Virtualized_Environment

  This server does not show in the

  Tested baselines (CRT)

  http://docwiki.Cisco.com/wiki/Tested_Reference_Configurations_%28TRC%29

  HTH

  Java

  If it helps, please note

  www.Cisco.com/go/pdihelpdesk

• Workstation 9 - broken PXE boot - works with 8 workstations

  VMware Workstation 9 newly released, the PXE boot is broken. It works on the same machine with VMware Workstation 8.

  
  Virtual machine specifications:

  -Windows 7 and Windows 7 x 64

  -Bridged networking

  -2 1 processor cores

  I tried on different hardware, without Windows Firewall, but the PXE boot is broken when you use Workstation 9. Any thoughts as to why her behave this way?

  We are trying to perform a PXE boot and it gets everything stuck by sending requests for the services of pre-launch on the remote server, however, it seems that the return packets are not received. On 8 workstations, these are received and PXE boot works correctly.

  There is no AV installed in the host operating system.

  Wow, okay, just confirmed this seems to be a MAJOR bug in the work station 9, concerning ONLY to run 2 hearts or 2 CPUs. I tested with my cell phone would support all configurations (this is a quad core with hyperthreading). This applies in my case to Novell Zenworks Imaging, but can affect more.

  Results

  Config	PXE
  1 processor, 1 core	Success
  1 CPU, Core 2	In case of failure
  1 CPU Core 3	Success
  1 CPU, Core 4	Success
  1 CPU, Core 6	Success
  1 CPU, Core 8	Success
  2 CPU, 1 core	In case of failure
  2 CPU, Core 2	Success
  2 CPU, Core 3	Success
  2 CPU, Core 4	Success
  4 CPU, 1 core	Success
  4 CPU, Core 2	Success
  8 CPU, 1 core	Success

  Now here it gets crazy. My issue seems to be with the v11.2.0.0 of the Agent Novell PXE (Preboot Execution). It says "Sending queries to xxx.xxx.xxx.xxx" then he received never actually do anything to continue the boot process, but ANY other config except 2 CPU or 2 cores CPU works fine.

• In-Guest iSCSI vMotion Support

  Hi, we use guest iSCSI using the Microsoft iSCSI initiator to host our volumes of Exchange 2010. We just noticed that the snapshots are not supported, can someone tell if vMotion is supported with this configuration, and nobody knows if snapshots will be build in ESX5?

  Hi, we use guest iSCSI using the Microsoft iSCSI initiator to host our volumes of Exchange 2010. We just noticed that the snapshots are not supported, can someone tell if vMotion is supported with this configuration, and nobody knows if snapshots will be build in ESX5?

  vMotion is supported, but you should check for yourself that the iSCSI target is accessible from all ESXi hosts. That is, with the other two *.vmdk, virtual disks and Raw Device Mappings the Vmkernel knows it of a disk that the virtual computer must and will check and make sure it is accessible from the other host.

  When you do internal iSCSI on the inside of the guest then these are just from the point of view Vmkernel network executives. He has no knowledge of what is sent to the VM and why.

  That is also the reason why you can't take snapshots of VMware on internal iSCSI disks. The discs are not "visible" at all from the ESXi host and may not use any method of people snapshoting.

• iMac 27 "with the second monitor boots black with cursor

  I can't seem to find another discussion altogether as my problem starting special 'black screen ':

  New iMac 27 "retina 5K (end of 2015) running OS X El Capitan 10.11.3 with second monitor Samsung connected by Mini DP - DVI.  When starting, the two screens are displayed in black, but the cursor is available and can be moved.

  I have to make a hard stop and disconnect the second monitor to start at the login screen. Then I can reconnect the monitor and everything works.

  Any suggestions for a fix?

  So, I spent some time with Apple customer support. Several of the standard troubleshooting for problems of mystery, they came to the conclusion that there was an incompatibility of driver with the Samsung monitor at startup which is mucking things up, and I just have to accept starting with the second disconnected monitor then plug it in again after a successful login.

  Samsung does not write the monitor for Mac drivers (for some reason any), that's why the customer support figures that there is a hangup at startup. But why OS X recognize the monitor and run fine otherwise? Why only hang at boot time? And why my Mac Book Pro 2007 running the same version of El Capitan boot fine with the connected monitor? It has something to do with the Thunderbolt/mini-DP-to-DVI connection? I don't know, and I guess that Apple's Support is not either.

  I fell on a hack, which is as follows:

  1. start with the second monitor connected

  2. in the "black screen with cursor" hold the power button quite long to put the computer to sleep

  3 wake up the computer with the keyboard or trackpad or other

  4 and now the login screen will appear.

  5 log in as usual.

  6.

  I hope this helps someone. One day I'll get a more compatible monitor and it will not be a Samsung.

  They make nice dish, however.

• Satellite Pro 6100 how to use recovery DVD-ROM with vmware products

  Hello

  I like to use the recovery DVDs of product (T201651-GR) of my Satelite Pro 6100 on VmWare player, because I use openSUSE Linux as main operating system (not Windows installed on the hard disk).
  I do like install and save hard disk laptop, so that to restore later inside the vmware. If it works?
  I wonder if someone can tell me how to use my legal version of Windows XP on VmWare player?

  Thank you in advance,
  Bernd

  Hello

  I doubt that it works with VmWare.
  Why?
  Because the restore CD contains the ghost image files and you will need to boot from the recovery CD for installation.

  So I see the chances of getting this job running VmWare.

• After the vista update, the file came out: \boot \BCD with status 0xc000000f. window cannot start and no response my installation dvd

  Last week I've updated in my vista once it was released the file: \boot \BCD with status 0xc000000f. I put my recovery disk window answered, is not obtained in the boot, press F8 did so. I considered that my hard drive was broken, so I changed the hard drive, but it can in installation but couldn't fix it and no driver may be dependent. What can I do? I did all thishttp://support.microsoft.com/kb/927391 step, still does not work. Help, please.

  I think you should contact the manufacturer about this problem with the Bios...

  It is usually F2 or delete to enter the Bios / configuration at startup.

  See you soon.

  Mick Murphy - Microsoft partner

• 6224 do not work with vmware 5.1 battery

  I have 2 switches 6224 with battery and config its ok.

  Dell #show switch

  Code of Plugged-in Switch preconfigured relief management
  SW status model ID ID of the model State Version
  --- ---------- --------- ------------- ------------- ------------- -----------
  1 Mgmt Sw PCT6224 PCT6224 OK 3.3.3.3
  2 the battery Oper Stby PCT6224 PCT6224 OK 3.3.3.3 Mbr

  but I have the same problem in my VMWare HA 5.1 environment

  example:

  I have 3 Server with 4 ports on each server

  Server 1 > 2 iSCSI ports and 2 ports for the network traffic
  Server 2 > 2 iSCSI ports and 2 ports for the network traffic
  Server 3 > 2 iSCSI ports and 2 ports for the network traffic

  Traffic networks

  Server 1 > 1 port to port 1 switch 1, 2 in the swtich 1 port port 2
  Server 2 > 1 port to port 2 switch 1, 2 in the swtich 2 port port 2
  Server 3 > 1 port to port 3 switch 1, 2 in 3 in swtich port port 2

  The problem, if I log out all switch ports 2 of trafficking networks, environmental works fine, but when I connect the cable of the switch 2
  the crash of the environment and the back work just when I disconnect the cable from the switch 2.
  In my VMWare Distributed Switch I configure 2 ports with route ip hash basis.

  I would like in my environment the switches in the stack to work with vmware HA in the network adapters on servers.

  sameone have sugestion for this problem for vmware works ok with dell stacked 6224

  Concerning

  Hello

  I can solve my problem.

  ports was config with frames in all the ports, I change to 1518 and too check that spanning tree enable in the ports of the vmware hosts, I disable spaning tree in the port of the host and stack of work 100%.

  Thank you all for the help

  Kind regards.

• ISCSI Boot B200 M2 need, but get 'not enough available vNIC.

  Hello

  I'm trying to implement initialization iSCSI ESXi on a B200 M2 w / M71KR-Q card above.

  I add vNIC A and B (each linked to a fabric respectively), but trying to implement a vNIC iSCSI - I get the error «not enough vNIC» available

  Looking around, it seems that M71KR-Q only can support 2 vNIC (which I also confirmed by trying to add a third, same error message as above).

  I just thought that since the overlay of iSCSI vNIC real - it works.

  However, even when adding just 1 vNIC and trying to superimpose a vNIC top iSCSI - I get the "there not enough resources overall, not enough vNIC available" error message.

  Does anyone know if it is even possible to initializing iSCSI on B200-M2 w / M71KR-Q on?

  Thanks in advance!

  Petar

  Please refer to this document in the section documents iSCSI boot https://supportforums.cisco.com/docs/DOC-18756 it is very detailed, I tell myself.

  initializing iSCSI is only supported on CiscoVIC and Broadcom mezz cards. It is not supported on the M71KR-Q Qlogic Gen - 1 mezz.

  Dave

• iSCSI Boot target IP Question

  Hi all

  Setting up iSCSI starts for the first time and had a question.

  Installation: Blades UCS about a pair of N5K (vPC) with a double NetApp controller connected.  There are 4 UCS vNIC - two for only iSCSI (as the VLAN native) and two for everything else.

  The blades odd dΘmarrez since LUN on NetApp controller and the blades even dΘmarrez since LUN on NetApp B controller.

  So my question.  When I make for an odd Blade (for example) iSCSI targets, do I have both A and B "NIC" s point on A controller's IP?  Or NIC - A point on A controller and IP point of NIC - B to B controller IP?  I was not sure that, in this example, the controller would hold unit number logic that this odd blade is starting from.

  Thank you!

  Hi Ian

  You can add up to two iSCSI vNIC startup strategy. A vNIC acts as the source of primary iSCSI boot, and the other acts as the source of secondary iSCSI boot.

  "point of NIC - A controller - A IP and NIC B points to the IP Address of the controller of B ' YES.

  You would create another strategy of starting for blades, with the primary order / trade school.

• UCS ISCSI Boot Jumb MTU

  Light and matter seeks jumbp MTU working for ISCSI boot.

  UCS 6248S

  IOM 2208

  VIC YEARS 1240

  5.1 ESXi update 1

  VNX 5500

  I have a few rack mount hosts with 10G network cards, who works with jumbo MTU and I can vmkping the VNX SPs with ' vmkping d s 7000 10.1.1.1 "and it works.

  In UCS the operating system starts on the VNX via ISCSI

  The ISCSI network is a pair of Dell Force 10 S4810s

  UCS FI - A and FI - B have 2 10 uplinks in a s port LACP on the strength of Dell 10 channel

  Checked the jumbo MTU is enabled on the side of Dell

  The system class QoS now occupies the 9216

  There is a QoS ESX ISCSI strategy mapped to the class gold

  ESX ISCSI strategy is mapped to 2 vNIC models; one fabric and a fabric b

  If I set the MTU on the vNIC model 9000 errors the OS at startup a message on start-up banks missing

  If I set the MTU on the vNIC model 1500 the host boots fine

  I put groups of ISCSI ports and vSwitch to 9000 in ESX, but I cannot ping the VNX SPs with a package of more than 1500.

  Attached is a diagram

  Someone at - he of the clues as to what I'm missing? Thank you

  Make sure that you assign you best effort to 9216 so class on the system UCS class.

  The return traffic is probably not sent with a COS value so the UCS is the treatment to best effort which by default is 1500.

  Joey

• 10 Easy Install Windows crashes with "VMware Fusion has encountered an error."

  When I tried to install Windows 10 Pro on VMware Fusion 8, easy installation process works normally for awhile then crashes with "VMware Fusion has encountered an error."

  I submitted a request for assistance, but other users have it met with the easy installation process?

  (Support information are attached.)

  -Douglas

  Hi Douglas,.

  It looks like a problem with your graphics driver or the graphics card:

  VMware.log said it was the SVGA thread that crashed:

  2015-09 - T 02, 07: 16:47 - 06:00 [+ 10.606] | SVGA | W115: Caught Signal 6 - tid 38927 (addr 7FFF914E9286)

  /var/log/system.log reveals that the pilot needed to restart the GPU seconds more host later:

  2 sep 07:16:56 Douglass-Mac-Pro kernel [0]: NVDA: GPU error detected!

  2 sep 07:16:56 Douglass-Mac-Pro kernel [0]: NVDA: call gpusKillClient for task 0xffffff80727586d0

  2 sep 07:16:56 Douglass-Mac-Pro kernel [0]: NVDA (OpenGL): channel timeout!

  2 sep 07:16:56 Douglass-Mac-Pro kernel [0]: NVDA: Info channel: [0, 47 x 31, 0 x 14, 0x1ca5ef]

  2 sep 07:16:56 Douglass-Mac-Pro kernel [0]: NVDA: Version Info: [com.nvidia.web.GeForceWeb, v10.0.5 0x5e5f4c655b, 19862786, 346.02.03f01, 1]

  Many other people are also experiencing problems with Fusion 8 graphics cards and spare parts and/or the driver Nvidia on the web here: conflicts of Fusion 8.0 with Nvidia driver of web for Mac

  Workarounds for this thread: try disabling acceleration 3D for the virtual machine.  Try to uninstall the driver Nvidia of the web and win back the builtin driver OS X.  If you use a spare graphics card, try reinstalling the original.

  See you soon,.

  --

  Darius

• No end of shooting reports supported by VMWare and VMWare tools Windos version?

  Hello.

  Now what I want to know exactly, that's the latest VMWare workstation with VMWare tools are supported on Windows 98 (Yes, sad, we must deploy some of these virtual machines in order to revive old software).

  Is there any public document describing VMWare tools OS are supported by the version of VMWare?

  Guys thank you very much in advance.

  According to the HCL, Windows 98 is supported for up to WS 9.0, the Tools for this version can be the one to use.

  André