Issue of 14.1.1 TMS Login banner

I see the banner Login of TMS to appear on every page, I sail in TMS 14.1.1.

We only see that after upgrading to TMS 14.1.1 - not seen in 13.2.1.

Is there a way to avoid this. ?

TMS has only been tested with IE and Firefox for Chrome can give you unexpected results for TMS that he has not been tested. Please see the installation guide for TMS 14.1.

http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/Install_Guide/Cisco_TMS_install_guide_14-1.PDF

Page 8

Perhaps a feature request can be opened for trials with chrome.

/ Magnus

Tags: Cisco Support

Similar Questions

Using NetConfig to push a new login banner.

LMS 3.2 - RME 4.3.1

I have problems using NetConfig to push a new login banner. I think the question is given that the router or a switch returns a line after the command banner login ^-the router or switch returns a line that says "Enter TEXT message. "Ends with the character" ^ ".

Here is an example;

Connection to router (config) #banner ^.

Enter a TEXT message. Ends with the character "^".

I tried Adhoc Netconfig work similar to the following;

connection of the banner ^

It is an example of our new banner.

blah, blah, blah,

blah, blah, blah

It is the end of our new banner.

^

I also tried to use the task called predefined NetConfig banner.

In both cases, the job failed because of the following:

"Or impossible orders on the insufficient No. device. the interactive responses (or timeout) for order: connection banner ^ »

Is there a way to enter the adhoc work in a or something?

Or do you know a way to use NetConfig to push new banners?

Thank you

Mike S.

Hi Mike,.
```
For multi-line banner command, you *should* use and --Now Run the Banner like below example: banner login ^C************************************** !!!!! ADVERTENCIA !!!!! this is the Banner
you will love it
hope it will work for you
******************************************************^C 
```
Thank you-

Alya

[Note the useful post]

Question about login banner

Hello-
I tried to place a page of SSH guard between the login screen and password since the upgrade from ESX to ESXi 5 4. Wondering if anyone has any insite. I was thinking be able to edit the /etc/ssh/sshd.conf file but not able to restart the service
Thanks in advice... with a bit of luck, I'll be able to answer my own question, but things have been very busy. If needed I can place the banner in MOTD.

Have you try to change your file/etc/issue?

Login banner ASCII text

Hi all

I wonder if we could make ASCII text/art on the banner of ASA of fantasy.

I tried to do the same thing as my other devices, but it does not accept it.

ASA5505 (config) # connection banner + -$

ASA5505 (config) # | This equipment is private owned and controlled.           $

| This equipment is private owned and controlled.             |

^

% ERROR: invalid input detected at ' ^' marker.

SW2 #sh run | b banner

connection of the banner ^ C

+--------------------------------------------------------------+

| This equipment is private owned and controlled.             |

| Unplug immediately if you are not an authorized user.    |

+--------------------------------------------------------------+

^ C

The problem with the banner is that it does not appear with SSH. Seems only to see the place with Telnet and I really do not use Telnet to manage the ASAs

You can get a message after login, but that really does not serve the purpose.

For this you can use

Banner motd

or

banner exec

-Jouni

TMS login

Hey all,.

OK, install a new TMS v14.1.1 Windows 2008 Server, joining the AD setup / domain accounts to the TMS. I have my Windows 7 PC on the same domain. When I connect to MSD he asks a user name & pass yet. What I am doing wrong? The CCC JAVA encourage also pop too.

Thank you

Justin Ferello
Technical Support Specialist
KBZ, a Cisco authorized dealer
e/v: [email protected] / * /

Hi, Justin.

In the options of IE, I think its on the content tab and if you click Custom settings for the intranet, you should get a few options. If you scroll down it is a scenery for authentication and you can set "auto login using your current credentials". That this setting is set on?

Im not sure if FF supports the automatc like that connection.

/ Magnus

Sent by Cisco Support technique iPhone App

Issue of AAA - Line Con 0 = login authentication (password)

Good afternoon everyone,

A simple nice for someone I am sure... I only of remote access to the network kit and therefore cannot test access to the Console.

I have a switch with the following configuration (excerpt)

!

Password username Admin Password123

!

AAA new-model

AAA authentication default login group Ganymede + local

!

Line con 0

Cisco connection authentication (where cisco is representative of a password)

NOTE: I have not username cisco password Admin in global config

My question is: with this current config access Console will stop using the configuration of default Ganymede for authentication and don't allow access to the line of the console if the cisco password is specified? In this case that the password is not defined in a global access, would be denied?

I've seen it before where you have exactly the same set up, but instead of referring to a value of password on the console line, you specify a list of names. For example, authentication of connection local CONSOLE_USERS, which would make sense, because you would be referring to a group on the Ganymede server named CONSOLE_USERS and only users defined in this group could access through the console, while the ACS server is running!

Any assistnace appreciated as I really want to get my head around ACS unconditionally

Thanks in advance

David

Yes, David, you can safetly delete this "authentication to connect cisco" line con 0.

About radius server take a look on:

http://www.shrubbery.NET/tac_plus/

On the radius server, I recommend freeradius for these tests.

(there much capacity of fever, then cisco ACS, but it can allow you easy test of the basic functions)

---

Michal

Issue update to profile Applications SSO Login Types of backend option

Hello
That's stupid questions, as I am unable to update Applications SSO Login Types profile backend value option also not sure if the option value profile which is been updated is the same as "s updated!
While integrating the R12 EBS OID 11g that I need set these profile option in backend EBS
1 the profile option 'Applications SSO Type' to 'SSWA w/SSO.
2 the 'application SSO Login Types' profile 'External' option (or BOTH).
3. the "Application SSO Auto Link User" profile option on 'Active '.
4. the profile option ' SSO Applications enable identity OID add the event ' on 'Active '.
Someone please prcisely could say how update the profile above options backend values.
When I ran this query.
Update fnd_profile_option_values
Set profile_option_value = "SSWA_SSO".
where PROFILE_OPTION_ID in (select PROFILE_OPTION_ID from the fnd_profile_options where PROFILE_OPTION_NAME = 'APPS_SSO')
and level_id = 10001 and profile_option_value! = "SSWA_SSO";

It returns the result 1 line update.
Not sure if the expected value and has updated it or not...

When I try to update Aapplications SSO Login Types ' profile option for 'External' (or BOTH). by running the following query
SQL > Update fnd_profile_option_values
Set profile_option_value = "BOTH".
where PROFILE_OPTION_ID in (select PROFILE_OPTION_ID from the fnd_profile_options where PROFILE_OPTION_NAME = 'APPS_SSO_LOCAL_LOGIN')
and level_id = 10001 and profile_option_value! = "BOTH";

Display: 0 line update.
Not sure why!

When I ask the table fnd_profile_options to determine what value of column level_id... It does not exist in fnd_profile_options
Could you please say what level_id in means of query above. I assuem its level value site but unable to check it out because I can't access the OAM or frontend Apps.

Is also one of the involuntary command which is executed
SQL > update fnd_profile_option_values
Set profile_option_value = "BOTH";

It ended with the release of more of 4200 lines update. Since this, the instance of mink but requires no corrective measures?

Thanks and greetings
Priya

You should add 'START' in the line before "DBMS_OUTPUT. DISABLE; ».

If you copy / paste the code I posted above, it should work.

Thank you

Hussein

Ganymede connection authentication failed

Hi all

We have a server RADIUS (v3.3) that seems to indicate certain characteristics of the strange. If we look at the authentication failure logs on GBA it shows what appears to be the Login banner, but also controls attempts in the field "user name". How is that possible? If the user failed to authenticate, should not show only the user name?

concerning

Keith

Yes, this will have the same effect. Here is the configuration of the example to fix these issues.

conf t

line to 0

20 session time-out! The session times out after 20 minutes of inactivity.

No motd-banner! disable the MOTD banner for reverse Telnet sessions

No exec

exec-timeout 0 0

Kind regards

Jagdeep

Unable to connect on the Microsoft account using computer

Hi all

Assistance required mentioned above mentioned the issue. I'm unable to login when I use desktop but the password works fine when I use other media.

Can someone help me

Hello

Thank you for visiting Microsoft Community.

According to the description, I understand that you are facing problems by connecting to your Microsoft Account. I will certainly help you to question.

I would like to know some information:

(1) you also receive error message when you try to connect to your account?

(2) have you tried to reset your password?

Also, I suggest you to refer to the link below and check if it helps:

http://Windows.Microsoft.com/en-GB/Windows/sign-in-cant

For more information, you can also check out the link below:

http://Windows.Microsoft.com/en-GB/Windows-8/passwords-in-Windows-8-FAQ

Hope this information helps.

Thank you to provide us with the information to look for more on this subject and to better understand the issue and we will be happy to offer our help.

Sincerely,

Ankit Rajput

EAP - TLS Questions...

Hi all

My setup is like this...

Laptop - LWAPP - WLC - ACS - AD

I m using CA to generate the certificate... I set up EAP - TLS on WLC & ACS SE. everything works fine it is to tell when I issue a CA on my AD login name & install this certificate I m able to connect to the WLAN... For safety on WLC I activate WPA & 802.1 x...

What I want is that when I start the laptop it should directly connect to the wireless network & whne I try to sign in using my user name & password that he should ask if my password is expired or something & connect to AD. But this is not case allowing to happen when we were using peap as it ask for username and paswword connect but not in the case of EAP_TLS it only to verify valid certificates...

Thanks in advance...

Kind regards

Piyush

EAP - TLS does not use a name of user and password only PEAP:

http://TechNet.Microsoft.com/en-us/library/cc739638.aspx

Web Auth customization (data type icon download?)

I recently installed 7.5 WLC and began a Web Auth customization base. I did my usual CLI commands to download my image when I discovered a new option, tranfer download data type icon. I tried to download a small picture to see what it would change, and I don't see anything in particular. Nobody knows what that change? (No it has not changed Cisco logos anywhere in the graphical interface, at least that I could see)

(Cisco Controller) > transfer download datatype?

code download an executable image on the system.
config download Configuration file.
eapcacert download a certificate from CA eap on the system.
eapdevcert download a certificate of dev eap on the system.
icon download an executable image on the system.
image upload a logo on the web page on the system.
ipseccacert download an IPSec certificate for the system.
ipsecdevcert download a certificate of dev IPSec for the system.
Login-banner download controller login banner. (Text only file supported: Max 1500 bytes & 18 lines, printable characters not unsupported)
signature download a signature for the system file.
webadmincert download a certificate of web directors on the system.
webauthbundle download a package webauth customized for the system.
webauthcert download a certificate web portal on the system.

Hey Robinson,

Sorry for the delay...

Download transfer data type icon

is the new order introduced on the WLC and especially for Mobile Concierge we have... it has more to do with the generic advertising Service 802.11U and please visit-

http://en.Wikipedia.org/wiki/IEEE_802.11U

This to load the icon for GAS on the WLC and nothing has to do with the connect/disconnect webauth pages...

We will ensure this is documented on the cisco properly guides...

Please let me know if that answers your question

Concerning

Surendra

Tripwire to PIX/IOS/CatOS agents?

My client is installed Tripwire and they have made Solaris agents and now look at my network devices.

Does anyone have experience with this? I can't find any useful information on the web about the functioning of these 'agents '. I almost expect an agent who lives on a server and connects to get the last configuration, rather than a process running on the box itself. However, if it IS a process that runs on the hardware platform, is it supported by Cisco, or will be the first thing I hear, technical support, be "Uninstall this Tripwire agent and see if the problem goes away."?

I guess you mean Tripwire Enterprise.

Tripwire supports a node "agentless". It's how they handle most I think of network devices. The server TE (frontend) has an agent installed on it and it initiates the connection and sends commands.

Tripwire calls rules COVR (output command Validation rule). Essentially a ssh session is open, then a "sh run" is sent, then analyzed by using a regular expression. You can also use the regex for find and replace certain lines of configuration (such as operating time). Something I saw during the implementation of MARCH is that there is a connection of size max banner. I have not stumbled upon this with Tripwire but if your connections fail, try to reduce your login banner.

I highly recommend the use of SSH and SCP. You can configure it to use TFTP too, but if you have SSH enabled on the device, it's just cleaner. Also, make sure you use variables for credentials. Tripwire has really only a right (in contrast to MARCH). You can create global variables in user name and password and then pull in for credentials when creating the node. This means that you define (or redefine) the name of user and password in 1 place instead of 500.

Make sure that your client has licenses for the nodes of the network. You can't swap the server and network nodes. In addition, make sure you get the network rules of Tripwire.

Two remote AnyConnect clients cannot get two voice via softphones?

We have a situation where two remote users of SSL VPNS cannot establish a voice call via softphones or cookie lync. They can both talk but I can't hear the other. Each user can call external or the office LAN without problems.

I'm under ASA version 9.1 (5) and v.3.1.05170 AnyConnect. Pretty basic config (purified) - any help would be appreciated!

# sh run
: Saved
:
ASA Version 9.1 (5)
!
host device name
something.com domain name
activate the encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
encrypted passwd
names of
General pool of local pool IP 10.x.x.x - 10.x.x.y
IP local pool pool-ops-TI 10.y.y.y - 10.y.y.z

interface GigabitEthernet0/0
nameif outside
security-level 0
IP x.x.x.x where x.x.x.x
!
interface GigabitEthernet0/1
description of the inside interface
nameif inside
security-level 100
IP address y.y.y.y y.y.y.y
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/6
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/7
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
Shutdown
No nameif
no level of security
no ip address
!
banner login ***********************************************************************
connection of the banner! ONLY AUTHORIZED USERS ARE ALLOWED TO CONNECT UNDER PENALTY OF LAW.
connection of the banner is a computer network that is private and can be used only in direct
banner connection explicit owner. The owner reserves the right to
banner connection monitor use this network to ensure the security of networks and respond
banner connect on specific allegations of misuse. Use of this network must
the banner sign a consent to the monitoring of these or other purposes.
connection banner in addition, the owner reserves the right to consent to a valid
application of law banner connection to search the network for evidence of a crime
banner stored within the network connection.
banner login ***********************************************************************
banner asdm ***********************************************************************
asdm banner! ONLY AUTHORIZED USERS ARE ALLOWED TO CONNECT UNDER PENALTY OF LAW.
asdm banner is a computer network that is private and can be used only in direct
banner asdm explicit owner. The owner reserves the right to
banner asdm monitor use this network to ensure the security of networks and respond
asdm banner of specific allegations of misuse. Use of this network must
banner asdm you consent to the monitoring of these or other purposes.
asdm banner in addition, the owner reserves the right to consent to a valid
application of law banner asdm to search the network for evidence of a crime
asdm banner stored within the network.
banner asdm ***********************************************************************
boot system Disk0: / asa915-smp - k8.bin
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT 1 Sun Mar 1 Sun Nov 02:00 02:00
DNS lookup field inside
DNS server-group DefaultDNS
Server name 192.168.0.0
Server name 192.168.0.0
something.com domain name
Local_LAN_Access list standard access allowed host 0.0.0.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer 40960
logging buffered stored notifications
logging trap notifications
record of the mistakes of history
notifications of logging asdm
logging - the id of the device hostname
logging inside 10.0.0.0 host
logging inside 10.0.0.0 host
Outside 1500 MTU
Within 1500 MTU
IP verify reverse path to the outside interface
IP verify reverse path inside interface
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any echo outdoors
ICMP allow any inaccessible outside
ICMP allow any inside
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
Route inside 10.0.0.0 255.0.0.0 y.y.y.y 1
Route inside 192.168.0.0 255.255.0.0 y.y.y.y 1
Route inside 0.0.0.0 0.0.0.0 y.y.y.y in tunnel
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
test_VPN card-attribute LDAP
name of the memberOf Group Policy map
map-value memberOf "CN = test VPN, OR = groups of VPN, OR = Groups, OU = company, DC =, DC =, DC = com" "test VPN".
dynamic-access-policy-registration DfltAccessPolicy
AAA-server test-deviceauth protocol ldap
Max - a attempts failed 5
AAA-server baird-deviceauth (inside) host 192.x.x.x
Server-port 636
LDAP-base-dn DC = x, DC =, DC = z
LDAP-scope subtree
LDAP-login-password
LDAP-connection-dn cn = b, OU = Service accounts, DC = x, DC =, DC = z
enable LDAP over ssl
microsoft server type
AAA-server test-rsa Protocol sdi
AAA-server test-rsa (inside) host
interval before attempt-3 new
AAA-server auth-ldap-tes ldap Protocol
AAA-server test-ldap-auth (inside) host
Server-port 636
LDAP-base-dn DC = country, DC = a, DC = com
LDAP-scope subtree
LDAP-login-password
LDAP-connection-dn CN = b, OU = Service accounts, DC = x, DC =, DC = z
enable LDAP over ssl
microsoft server type
LDAP-attribute-map test_VPN
identity of the user by default-domain LOCAL
the ssh LOCAL of baird-deviceauth console AAA authentication
HTTP authentication AAA console LOCAL baird-deviceauth
serial baird-deviceauth LOCAL console AAA authentication
Enable http server
http inside x.x.x.x y.y.y.y
HTTP 1.1.1.1 255.255.255.0 inside
redirect http outside 80
SNMP-server host inside x.x.x.x trap community version 2 c
SNMP server location
contact SNMP Server
SNMP-server community
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Server enable SNMP traps entity power cpu-temperature
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint trustpoint-selfsigned-vpncso
registration auto
FQDN
name of the object CN =, O =, C =, St =, =.
key pair
Configure CRL
Crypto ca trustpoint
Terminal registration
Configure CRL
Crypto ca trustpoint
Terminal registration
FQDN
name of the object CN = OR =, O =, C = St =, =.
key pair
Configure CRL
Crypto ca trustpoint
Terminal registration
Configure CRL
Crypto ca trustpoint
Terminal registration
Configure CRL
Crypto ca trustpoint
Terminal registration
Configure CRL
trustpool crypto ca policy

Telnet timeout 5
SSH enable ibou
SSH stricthostkeycheck
x.x.x.x inside SSH
SSH timeout 30
SSH version 2
SSH group dh-Group1-sha1 key exchange
Console timeout 15
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
no statistical access list - a threat detection
no statistical threat detection tcp-interception
NTP server 1.1.1.1 source inside
NTP server 2.2.2.2 source inside
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
AnyConnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 2
AnyConnect profiles baird-client-profile disk0: / customer-baird - profile .xml
AnyConnect enable
attributes of Group Policy DfltGrpPolicy
value of banner! ONLY AUTHORIZED USERS ARE ALLOWED TO CONNECT UNDER PENALTY OF LAW.
value of banner is a computer network that is private and can be used only in direct
banner value explicit owner. The owner reserves the right to
banner value monitor use this network to ensure the security of networks and respond
the value of the banner of the specific allegations of misuse. Use of this network must
value of the banner a consent to the monitoring of these or other purposes.
value of server DNS 1.1.1.1 2.2.2.2
VPN - connections 2
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy excludespecified
value of Split-tunnel-network-list Local_LAN_Access
something.com value by default-field
Split-dns value something.com, us.something.com
activate dns split-tunnel-all
the address value general-pool pools
WebVPN
use-smart-tunnel homepage
AnyConnect value dart modules, nam
AnyConnect value profiles baird-client-profile user type
AnyConnect ask flawless anyconnect
Group Policy 'test' internal
Group Policy attributes 'test '.
Split-tunnel-policy excludespecified
value of Split-tunnel-network-list Local_LAN_Access
activate dns split-tunnel-all
the address value it-ops-pool pools
internal testMacs group policy
attributes of the strategy of group testMacs
WINS server no
value of server DNS 1.1.1.1 2.2.2.2
client ssl-VPN-tunnel-Protocol
field default value xyz.com
username admin privilege 15 encrypted password
attributes global-tunnel-group DefaultRAGroup
test-rsa authentication-server-group
test-ldap-auth authorization-server-group
management of the password password-expire-to-days 10
tunnel-group DefaultRAGroup webvpn-attributes
the aaa authentication certificate
attributes global-tunnel-group DefaultWEBVPNGroup
test-rsa authentication-server-group
test-ldap-auth authorization-server-group
management of the password password-expire-to-days 10
tunnel-group DefaultWEBVPNGroup webvpn-attributes
the aaa authentication certificate
tunnel-group test remote access connection type
tunnel-group test-Connect General attributes
test-rsa authentication-server-group
test-ldap-auth authorization-server-group
management of the password password-expire-to-days 10
tunnel-group test connection webvpn-attributes
the aaa authentication certificate
allow group-url http://abc.xyz.com
allow group-url https://abc.xyz.rwbaird.com
type tunnel-group testMacs remote access
tunnel-group testMacs General-attributes
test-rsa authentication-server-group
test-ldap-auth authorization-server-group
Group Policy - by default-testMacs
management of the password password-expire-to-days 10
use-set-name of the secondary-username-of-certificate
tunnel-group testMacs webvpn-attributes
allow group-url http://abc.xyz.com/macs
allow group-url https://abc.xyz.com/macs
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 26
Subscribe to alert-group configuration periodic monthly 26
daily periodic subscribe to alert-group telemetry
Cryptochecksum:aa675139dc84529791f9aaba46eb17f9
: end

I confess that I have not read your config in detail, but a few tips:

-If you do split tunnel, don't forget to push a route for the entire pool VPN subnet or subnets of VPN clients

-Make sure you have the same-security-traffic permitted intra-interface

http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa81/command/ref/refg...

-If you use NAT, you must exclude such NAT inter-VPN-device traffic

-If you have ACLs (not shown) do not forget to leave your pool VPN subnet is talking to himself. Generally, it would be in the ACL entering the external interface.

at the end of the packet - trace is your friend.

NGP

Site to site vpn errors.

When you configure a site to tunnles, I get errors in logging of ASA of gall.

I've included the two configs on the walls of ASA file.

any one see what Miss me?

small site

: Saved

: Written by usiadmin at 15:22:08.143 UTC Monday, March 19, 2012

!

ASA Version 7.2 (3)

!

hostname smallASA

domain.com domain name

activate awSQhSsotCzGWRMo encrypted password

names of

!

interface Vlan1

nameif inside

security-level 100

IP 10.16.4.1 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP 116.12.211.66 255.255.255.240

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

L0Wjs4eA25R/befo encrypted passwd

passive FTP mode

DNS lookup field inside

DNS server-group DefaultDNS

Server name 10.10.20.1

domain.com domain name

access extensive list ip 10.16.4.0 outside_1_cryptomap allow 255.255.255.0 any

access extensive list ip 10.16.4.0 inside_nat0_outbound allow 255.255.255.0 any

pager lines 24

Enable logging

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 523.bin

don't allow no asdm history

ARP timeout 14400

NAT-control

Global 1 interface (outside)

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 0.0.0.0 0.0.0.0

Route outside 0.0.0.0 0.0.0.0 116.12.211.65 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout, uauth 0:05:00 absolute

Enable http server

http 0.0.0.0 0.0.0.0 outdoors

http 10.16.4.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs

peer set card crypto outside_map 1 12.69.103.226

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

Crypto isakmp nat-traversal 20

Telnet 10.16.4.0 255.255.255.0 inside

Telnet timeout 5

SSH 10.16.4.0 255.255.255.0 inside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 5

Console timeout 0

dhcpd dns 165.21.83.88 10.10.2.1

dhcpd domain domain.com

dhcpd outside auto_config

!

dhcpd address 10.16.4.100 - 10.16.4.131 inside

dhcpd allow inside

!

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

!

global service-policy global_policy

usiadmin encrypted DI5M5NnQfLzGHaw1 privilege 15 password username

initech encrypted ENDpqoooBPsmGFZP privilege 15 password username

tunnel-group 12.69.103.226 type ipsec-l2l

IPSec-attributes tunnel-group 12.69.103.226

pre-shared key, PSK

context of prompt hostname

Cryptochecksum:e6bf95f3c25574bfed2adafb3283e882

: end

large site

: Saved

: Written by usiadmin to the 22:57:30.549 CDT Monday, March 19, 2012

!

ASA Version 8.0 (3)

!

hostname STO-ASA-5510-FW

domain.com domain name

enable the password... Ge0JnvJlk/gAiB encrypted

names of

192.168.255.0 BGP-Transit_Network description name Transit BGP

name 10.10.99.0 VPN

name 10.10.2.80 BB

DNS-guard

!

interface Ethernet0/0

Inside the Interface Description

nameif inside

security-level 100

IP 10.10.200.29 255.255.255.240

OSPF cost 10

!

interface Ethernet0/1

Description external Interface facing the Rotuer for Internet.

nameif outside

security-level 0

IP 12.69.103.226 255.255.255.240

OSPF cost 10

!

interface Ethernet0/2

Description physical interface trunk - do not use

No nameif

no level of security

no ip address

!

interface Ethernet0/2.900

Description Interface DMZ 12.69.103.0 / 26 (usable hotes.1 a.62)

VLAN 900

nameif DMZ1-VLAN900

security-level 50

IP 12.69.103.1 255.255.255.192

OSPF cost 10

!

interface Ethernet0/3

Shutdown

No nameif

no level of security

no ip address

!

interface Management0/0

nameif management

security-level 100

IP 10.10.5.250 255.255.254.0

OSPF cost 10

management only

!

L0Wjs4eA25R/befo encrypted passwd

banner exec **********************************************************************

exec banner STO-ASA-5510-FW

exec banner ASA5510 - 10.10.200.29

exec banner configured for data use only

banner exec **********************************************************************

banner login **********************************************************************

connection of the banner caveat: this system is for the use of only authorized customers.

banner of individuals to connect using the system of computer network without permission.

banner login or exceeding their authority, are subject with all their

activity of connection banner on this system monitored and recorded by computer network

staff of the login banner system. To protect the computer network system of

banner of the connection of unauthorized use and to ensure that computer network systems is

connection of banner works properly, system administrators monitor this system.

banner connect anyone using this computer network system expressly consents to such a

banner of the connection monitoring and is advised that if such monitoring reveals possible

conduct of connection banner of criminal activity, system personnel may provide the

evidence of connection banner of such activity to the police.

connection banner that access is restricted to the authorized users only. Unauthorized access is

connection banner, a violation of State and federal, civil and criminal.

banner login **********************************************************************

passive FTP mode

clock timezone CST - 6

clock to summer time recurring CDT

DNS server-group DefaultDNS

domain universalsilencer.com

permit same-security-traffic intra-interface

object-group service SAP tcp - udp

Description SAP updates

port-object eq 3299

object-group Protocol TCPUDP

object-protocol udp

object-tcp protocol

object-group service HUMANLand tcp

port-object eq citrix-ica

DM_INLINE_TCP_1 tcp service object-group

EQ port 5061 object

port-object eq www

EQ object of the https port

DM_INLINE_TCP_2 tcp service object-group

EQ port 5061 object

port-object eq www

EQ object of the https port

DM_INLINE_UDP_1 udp service object-group

EQ port-object snmp

port-object eq snmptrap

object-group service DM_INLINE_SERVICE_1

ICMP service object

the purpose of the service tcp - udp eq www

the purpose of the udp eq snmp service

the purpose of the udp eq snmptrap service

the eq syslog udp service object

the eq 2055 tcp service object

the eq 2055 udp service object

EQ-3389 tcp service object

object-group service human tcp - udp

port-object eq 8100

object-group service grove tcp

port-object eq 2492

netflowTcp tcp service object-group

port-object eq 2055

object-group service 6144 tcp - udp

6144 description

port-object eq 6144

object-group service 1536-DMPA-inter-tcp - udp

1536-DMPA-inter description

port-object eq 1536

the DM_INLINE_NETWORK_1 object-group network

network-object 198.78.0.0 255.255.0.0

network-object 207.152.0.0 255.255.0.0

network-object 69.31.0.0 255.255.0.0

the DM_INLINE_NETWORK_2 object-group network

network-object 198.78.0.0 255.255.0.0

network-object 207.152.0.0 255.255.0.0

network-object 69.31.0.0 255.255.0.0

the DM_INLINE_NETWORK_3 object-group network

network-object 198.78.0.0 255.255.0.0

network-object 207.152.0.0 255.255.0.0

network-object 69.31.0.0 255.255.0.0

the DM_INLINE_NETWORK_4 object-group network

network-object 198.78.0.0 255.255.0.0

network-object 207.152.0.0 255.255.0.0

network-object 69.31.0.0 255.255.0.0

object-group service rdp tcp

RDP description

EQ port 3389 object

the DM_INLINE_NETWORK_5 object-group network

network-object 10.16.0.0 255.255.0.0

object-network 10.16.0.0 255.255.255.0

the DM_INLINE_NETWORK_6 object-group network

network-object 10.16.0.0 255.255.0.0

object-network 10.16.0.0 255.255.255.0

the DM_INLINE_NETWORK_7 object-group network

network-object 10.16.0.0 255.255.0.0

object-network 10.16.0.0 255.255.255.0

the DM_INLINE_NETWORK_8 object-group network

network-object 10.16.0.0 255.255.0.0

object-network 10.16.0.0 255.255.255.0

access outside the 207.152.125.136 note list

extended access list to refuse any newspaper outdoors the object-group objects DM_INLINE_NETWORK_1 TCPUDP-group

scope of list of outdoor access to refuse the object-group objects DM_INLINE_NETWORK_2 host 12.69.103.129 TCPUDP-group

extended access list to refuse the object-group TCPUDP outdoors any object-group DM_INLINE_NETWORK_3

scope of list of outdoor access to refuse the subject-TCPUDP 12.69.103.129 host object group DM_INLINE_NETWORK_4

access outside the note list * in Bound SAP traffic by Ron Odom update *.

list of access outside the scope permitted tcp host 194.39.131.34 host 12.69.103.155 3200 3300 Journal range

access outside the note list * router SAP *.

list of access outside the permitted range tcp host 10.10.2.110 host 194.39.131.34 3200 3300

extended access list permits object-group DM_INLINE_SERVICE_1 outside any host 12.69.103.154

access outside the note list * entrants to the mail server to 10.10.2.10 Peter K *.

list of extended outside access permit tcp any host 12.69.103.147 eq smtp

access outside the note list * incoming to the OCS EDGE on DMZ Peter K *.

access list outside extended permit tcp any host 12.69.103.2 object - group DM_INLINE_TCP_1

list of external extended ip access permits any host 12.69.103.6

list of access outside the comment flagged for malware activity

scope of list of outdoor access to deny the host ip 77.78.247.86 all

list of external extended ip access permits any host 12.69.103.156 inactive

list of extended outside access permit tcp any host 12.69.103.147 eq www

list of extended outside access permit tcp any host 12.69.103.147 eq https

access outside the note list * incoming hosting 10.10.3.200 - Dan K *.

list of extended outside access permit tcp any host 12.69.103.145 eq www

list of extended outside access permit tcp any host 12.69.103.145 eq https

access outside the note list * journey to host 10.10.2.30 USIFAXBACK - Dan K *.

list of extended outside access permit tcp any host 12.69.103.146 eq www

list of extended outside access permit tcp any host 12.69.103.146 eq https

access outside the note list * incoming hosting 10.10.8.5 - Mitel 7100 BOB M 4/4-2008 - BV *.

list of extended outside access permit tcp any host 12.69.103.152 eq pptp

access list outside extended permit tcp any host 200.56.251.118 object - group HUMANLand

list of extended outside access permit tcp any host 200.56.251.121 eq 8100

outdoor access list note allow all return ICMP traffic off in order to help the attacks of hidden form

extended the list of outdoor access to deny icmp everything no matter what newspaper

list of allowed outside access extended ip 10.14.0.0 255.255.0.0 all open a debug session

list of allowed outside access extended ip 10.15.0.0 255.255.0.0 any

list of allowed outside access extended ip object-group DM_INLINE_NETWORK_7 all

outdoor access list extended permits all ip 10.14.0.0 255.255.0.0 debug log

outdoor access list extended permits all ip 10.15.0.0 255.255.0.0

list of external extended ip access permits any object-group DM_INLINE_NETWORK_6

list of access outside the scope permitted udp host 12.88.249.62 any DM_INLINE_UDP_1 object-group

Note added to pervent bocking human outside access list

list of access outside the permitted scope object-TCPUDP host 10.12.2.250 host 200.56.251.121 human group object

Note added to pervent bocking human outside access list

list of access outside the permitted scope object-TCPUDP host 200.56.251.121 host 10.12.2.250 human group object

outside the permitted scope of access tcp list any any eq log pptp

extended access list to refuse the object-group TCPUDP outdoors everything any object-group 6144

VPN-SplitTunnel extended 10.10.0.0 ip access list allow 255.255.0.0 VPN 255.255.255.192

extensive list of access VPN-SplitTunnel ip 10.11.0.0 255.255.0.0 VPN 255.255.255.192 allow

extended VPN-SplitTunnel access list ip 10.12.0.0 allow 255.255.0.0 VPN 255.255.255.192

extended VPN-SplitTunnel access list ip 10.13.0.0 allow 255.255.0.0 VPN 255.255.255.192

list of access VPN-SplitTunnel extended permitted ip VPN BGP-Transit_Network 255.255.255.0 255.255.255.192

list of access VPN-SplitTunnel extended permitted ip 10.0.0.0 255.0.0.0 192.168.10.0 255.255.255.0

VPN-SplitTunnel extended 10.10.0.0 ip access list allow 255.255.0.0 10.14.4.0 255.255.254.0

VPN-SplitTunnel extended 10.10.0.0 ip access list allow 255.255.0.0 10.15.4.0 255.255.254.0

VPN-SplitTunnel extended 10.10.0.0 ip access list allow 255.255.0.0 10.14.8.0 255.255.254.0

Note DMZ1_in access-list * OCS - 2nd interface to inside EDGE welcomes Peter K *.

DMZ1_in list extended access permit tcp host 12.69.103.3 host 10.10.2.15 DM_INLINE_TCP_2 object-group

Note DMZ1_in of access list permit all ICMP traffic

DMZ1_in access list extended icmp permitted any any newspaper

DMZ1_in deny ip extended access list all 207.152.0.0 255.255.0.0

DMZ1_in list extended access deny ip 207.152.0.0 255.255.0.0 any

Note DMZ1_in access-list * explicitly block access to all domestic networks *.

Note access-list DMZ1_in * no need allowed inside networks *.

Note DMZ1_in access-list * to do above this section *.

DMZ1_in list extended access deny ip any 10.0.0.0 255.0.0.0

DMZ1_in list extended access deny ip any 172.16.0.0 255.240.0.0

DMZ1_in list extended access deny ip any 192.168.0.0 255.255.0.0

Note DMZ1_in access-list * IP Allow - this will be the internet *.

DMZ1_in list of allowed ip extended access all any debug log

ezvpn1 list standard access allowed 10.0.0.0 255.0.0.0

access-list DMZ1-VLAN900_cryptomap extended ip allowed any one

access-list sheep extended ip 10.10.0.0 allow 255.255.0.0 VPN 255.255.255.192

IP 10.11.0.0 allow Access-list extended sheep 255.255.0.0 VPN 255.255.255.192

IP 10.12.0.0 allow Access-list extended sheep 255.255.0.0 VPN 255.255.255.192

access-list extended sheep ip 10.13.0.0 allow 255.255.0.0 VPN 255.255.255.192

access-list sheep extended ip VPN BGP-Transit_Network 255.255.255.0 allow 255.255.255.192

access-list extended sheep allowed ip 10.0.0.0 255.0.0.0 192.168.10.0 255.255.255.0

access-list sheep extended ip 10.10.0.0 allow 255.255.0.0 10.14.4.0 255.255.254.0

access-list sheep extended ip 10.10.0.0 allow 255.255.0.0 10.14.8.0 255.255.254.0

access-list extended sheep allowed ip 10.0.0.0 255.0.0.0 10.14.0.0 255.255.0.0

access-list sheep extended ip 10.10.0.0 allow 255.255.0.0 10.15.4.0 255.255.254.0

access-list extended sheep allowed ip 10.0.0.0 255.0.0.0 10.15.0.0 255.255.0.0

permit traffic to access extended list ip 10.0.0.0 255.0.0.0 10.14.0.0 inactive 255.255.0.0

outside_cryptomap to access ip 10.0.0.0 scope list allow 255.0.0.0 10.15.0.0 255.255.0.0

access extensive list ip 10.14.0.0 outside_nat0_outbound allow 255.255.0.0 VPN 255.255.255.192

access extensive list ip 10.15.0.0 outside_nat0_outbound allow 255.255.0.0 VPN 255.255.255.192

outside_nat0_outbound list extended access allowed object-group ip VPN DM_INLINE_NETWORK_8 255.255.255.192

outside_cryptomap_1 to access ip 10.0.0.0 scope list allow 255.0.0.0 DM_INLINE_NETWORK_5 object-group

pager lines 24

Enable logging

timestamp of the record

logging list VPN informational level class auth

logging list class VPN config level criticism

VPN vpn list logging level notification class

notification of log list VPN vpnc level class

VPN list logging level notifications class webvpn

logging alerts list any level

exploitation forest-size of the buffer of 256000

logging buffered all

logging VPN trap

asdm of logging of information

host of inside the 10.10.2.41 logging format emblem

logging ftp-bufferwrap

connection server ftp 10.10.2.41 \logs usi\administrator 178US1SIL3 ~.

Within 1500 MTU

Outside 1500 MTU

MTU 1500 DMZ1-VLAN900

management of MTU 1500

mask 10.10.99.1 - 10.10.99.63 255.255.255.192 IP local pool Clients_vpn

no failover

ICMP unreachable rate-limit 1 burst-size 1

ICMP allow any inside

ICMP allow all outside

ICMP allow any DMZ1-VLAN900

ASDM image disk0: / asdm - 611.bin

ASDM location VPN 255.255.255.192 inside

ASDM location BGP-Transit_Network 255.255.255.0 inside

ASDM location 10.10.4.60 255.255.254.255 inside

ASDM location 255.255.255.255 inside BB

ASDM location 10.16.0.0 255.255.0.0 inside

ASDM location 69.31.0.0 255.255.0.0 inside

ASDM location 198.78.0.0 255.255.0.0 inside

ASDM location 10.16.0.0 255.255.255.0 inside

enable ASDM history

ARP timeout 14400

Global (inside) 1 10.10.2.4 netmask 255.0.0.0

Global (outside) 10 12.69.103.129 netmask 255.255.255.255

Global (outside) 11 12.69.103.130 netmask 255.255.255.255

Global (outside) 12 12.69.103.131 netmask 255.255.255.255

Global (outside) 13 12.69.103.132 netmask 255.255.255.255

Global (outside) 14 12.69.103.133 netmask 255.0.0.0

NAT (inside) 0 access-list sheep

NAT (inside) 11 192.168.255.4 255.255.255.252

NAT (inside) 12 192.168.255.8 255.255.255.252

NAT (inside) 13 192.168.255.12 255.255.255.252

NAT (inside) 10 10.10.0.0 255.255.0.0

NAT (inside) 11 10.11.0.0 255.255.0.0

NAT (inside) 12 10.12.0.0 255.255.0.0

NAT (inside) 13 10.13.0.0 255.255.0.0

NAT (inside) 10 10.14.0.0 255.255.0.0

NAT (outside) 0-list of access outside_nat0_outbound

NAT (outside) 10 10.16.0.0 255.255.255.0

NAT (outside) 10 10.14.0.0 255.255.0.0

NAT (outside) 10 10.15.0.0 255.255.0.0

NAT (outside) 10 10.16.0.0 255.255.0.0

static (DMZ1-VLAN900, external) 12.69.103.0 12.69.103.0 subnet mask 255.255.255.192

public static 12.69.103.154 (Interior, exterior) 10.10.2.41 netmask 255.255.255.255

static (inside, DMZ1-VLAN900) 10.0.0.0 10.0.0.0 netmask 255.0.0.0

static (inside, DMZ1-VLAN900) 192.168.0.0 192.168.0.0 netmask 255.255.0.0

static (inside, DMZ1-VLAN900) 172.16.0.0 subnet 255.240.0.0 172.16.0.0 mask

public static 12.69.103.147 (Interior, exterior) 10.10.2.10 netmask 255.255.255.255

public static 12.69.103.152 (Interior, exterior) 10.10.8.5 netmask 255.255.255.255

public static 12.69.103.155 (Interior, exterior) 10.10.2.110 netmask 255.255.255.255

outside access-group in external interface

Access-group DMZ1_in in interface DMZ1-VLAN900

!

Router eigrp 100

Network 10.0.0.0 255.0.0.0

!

Route outside 0.0.0.0 0.0.0.0 12.69.103.225 1

Route inside 10.0.0.0 255.0.0.0 10.10.200.30 1

Route inside 10.10.98.0 255.255.255.0 10.10.200.30 1

Route outside 10.14.0.0 255.255.0.0 12.69.103.225 1

Route outside 10.15.0.0 255.255.0.0 12.69.103.225 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout, uauth 0:05:00 absolute

dynamic-access-policy-registration DfltAccessPolicy

AAA-server Microsoft radius Protocol

simultaneous accounting mode

reactivation mode impoverishment deadtime 30

AAA-server Microsoft host 10.10.2.1

key cisco123

the ssh LOCAL console AAA authentication

AAA authentication LOCAL telnet console

AAA authentication enable LOCAL console

AAA authentication http LOCAL console

Enable http server

http 10.10.0.0 255.255.0.0 management

http 10.10.0.0 255.255.0.0 inside

SNMP-server host within the 10.10.2.41 community UNISNMP version 2 c-port udp 161

location of Server SNMP STODATDROOM

contact SNMP SYS Admin Server

UNISNMP SNMP-server community

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Server enable SNMP traps syslog

Server SNMP traps enable ipsec works stop

Server enable SNMP traps entity config - change insert-fru fru - remove

Server SNMP enable doors remote access has exceeded the threshold of session

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

card crypto outside_map 1 match address outside_cryptomap

peer set card crypto outside_map 1 115.111.107.226

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

card crypto outside_map 2 match address outside_cryptomap_1

peer set card crypto outside_map 2 116.12.211.66

card crypto outside_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

address card crypto outside_map 10 game traffic

peer set card crypto outside_map 10 212.185.51.242

outside_map crypto 10 card value transform-set ESP-3DES-SHA

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

inside crypto map inside_map interface

card crypto DMZ1-VLAN900_map0 1 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

crypto isakmp identity address

crypto ISAKMP allow inside

crypto ISAKMP allow outside

crypto ISAKMP policy 5

preshared authentication

3des encryption

sha hash

Group 2

life no

crypto ISAKMP policy 10

preshared authentication

the Encryption

sha hash

Group 2

life no

Crypto isakmp nat-traversal 33

No vpn-addr-assign aaa

No dhcp vpn-addr-assign

VPN-addr-assign local reuse-delay 10

Telnet 10.10.0.0 255.255.0.0 inside

Telnet 10.10.0.0 255.255.0.0 management

Telnet timeout 29

SSH timeout 29

SSH version 2

Console timeout 1

management-access inside

dhcprelay Server 10.10.2.1 outside

a basic threat threat detection

threat scan-threat shun except ip 10.14.0.0 address detection 255.255.0.0

threat scan-threat shun except ip 10.15.0.0 address detection 255.255.0.0

threat detection statistics

Web cache WCCP

WCCP interface within web in cache redirection

NTP 192.5.41.41 Server

NTP 192.5.41.40 Server

Server NTP 192.43.244.18

TFTP server inside 10.10.2.2 \asa

attributes of Group Policy DfltGrpPolicy

banner of value WARNING: this system is for the use of only authorized customers.

value of server WINS 10.10.2.1

value of 10.10.2.1 DNS server 10.10.2.2

Protocol-tunnel-VPN IPSec svc webvpn

Split-tunnel-policy tunnelspecified

Split-tunnel-network-list value VPN-SplitTunnel

universalsilencer.com value by default-field

Server proxy Internet Explorer 00.00.00.00 value

the address value Clients_vpn pools

internal CHINAPH group policy

CHINAPH group policy attributes

Protocol-tunnel-VPN IPSec svc webvpn

Split-tunnel-policy tunnelall

enable dhcp Intercept 255.255.0.0

the address value Clients_vpn pools

internal ezGROUP1 group policy

attributes of the strategy of group ezGROUP1

VPN-tunnel-Protocol svc webvpn

allow password-storage

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list ezvpn1

allow to NEM

deleted users

IPSec-attributes tunnel-group DefaultL2LGroup

pre-shared-key germanysilence

type tunnel-group USISplitTunnelRemoteAccess remote access

attributes global-tunnel-group USISplitTunnelRemoteAccess

address pool Clients_vpn

IPSec-attributes tunnel-group USISplitTunnelRemoteAccess

pre-shared-key z2LNoioYVCTyJlX

type tunnel-group USISplitTunnelRADIUS remote access

attributes global-tunnel-group USISplitTunnelRADIUS

address pool Clients_vpn

Group-Microsoft LOCAL authentication server

IPSec-attributes tunnel-group USISplitTunnelRADIUS

pre-shared-key fLFO2p5KSS8Ic2y

type tunnel-group ezVPN1 remote access

tunnel-group ezVPN1 General-attributes

Group Policy - by default-ezGROUP1

ezVPN1 group of tunnel ipsec-attributes

pre-shared key, PSK

tunnel-group 212.185.51.242 type ipsec-l2l

IPSec-attributes tunnel-group 212.185.51.242

pre-shared key, PSK

NOCHECK Peer-id-validate

tunnel-group 115.111.107.226 type ipsec-l2l

IPSec-attributes tunnel-group 115.111.107.226

pre-shared key PSJ

tunnel-Group China type remote access

attributes global-tunnel-Group China

address pool Clients_vpn

Group Policy - by default-CHINAPH

tunnel-group 116.12.211.66 type ipsec-l2l

IPSec-attributes tunnel-group 116.12.211.66

pre-shared key, PSK

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns migrated_dns_map_1

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the migrated_dns_map_1 dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

inspect the icmp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:834976612f8f76e1b088326516362975

: end

Hello Ronald.

You use PFS on a site and not on the other.

Allows to remove from the site that has it and give it a try.

Change this:

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs

peer set card crypto outside_map 1 12.69.103.226

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

outside_map interface card crypto outside

To do this:

card crypto outside_map 1 match address outside_1_cryptomap

peer set card crypto outside_map 1 12.69.103.226

card crypto outside_map 1 set of transformation-ESP-3DES-SHA

outside_map interface card crypto outside

So just do a

NO card crypto outside_map 1 set pfs

Kind regards

Julio

Note all useful posts

If subscribe link missing

I create a new app from the dps with rights and itunes subscriptions. After completing the app is missing something: the Subscribe link in the title line (see picture). Is this an error in the new Viewer 25er?
(The itunes subscription works through the first issue of the magazine (I use a banner of law instead of a banner of itunes subscription)).

In the generator of the App, there is an option to show or hide the link to subscribe. Check the App details under Advanced options screen.

Issue of 14.1.1 TMS Login banner

Similar Questions

Maybe you are looking for