Issue of speed of connection about 4965 A/G/N

Similar Questions

• WRT320N slows down the speed of connection - terms of support of Linksys problem

  My internet connection speed slows down to about half of it is normal speed (or worse) until I have restart my router WRT320N. I see on the net that MANY other people have the same problem and can't seem to find a solution to this problem.

  I have the latest version of the firmware installed and I have the upnp is off

  I was told recently by a representative of Linksys Chat to perform this procedure, and I was wondering if anyone has tried and there set the coupling apparently daily slowdown that set in a reboot of the router for another day or two

  Here is the procedure that I was instructed to do...
  I was told disconnest the modem to the router-connect "than a PC ONLY" via a wired port #4 - reset the router by holding the button of reset in 30 seconds - switch off the router Linksys for 20 seconds and then turn it back on - check the LEDs of the Linksys router to make sure that the power, WLAN and port #4 are lit on the Linksys router. -clone the MAC - change "Mixed" wireless settings - name - change to 20 Mhz channel bandwidth and network use standard channel 11 - and in - use the Mode personal WPA - security settings and set my WPA pre-shared key password
  Before shutting down the PC and router - reconnect the modem to the router and the PC to the router - then make sure that the modem, the router and the PC are disabled for cycle a minute and the power of their back on with the modem being first - then turn on the router and last the PC

  Has anyone tried this, and he had to fix this downturn?

  Thanks in advance

  Well it's been 6 days that I woke up this morning and turned on the router and the modem from power overnight or lower I did after question troubleshooting the slow speed in the night before, does not

  I consistantly get in the 2 to 3% of the broadband speed I pay for - but I have no idea what fixed the issue

  So I'll mark it as "Resolved" and just hope that it comes not back again

  Thanks for the recommendations Klatch

• Connectivity issues while trying to connect in spades to MSN on the computer

  * Original title: msn Spades - he works?

  I can't log on to msn Spades; something about connectivity issues; can someone help here?

  Hi Steve-Bob,

  Thanks for posting your question in the Microsoft Community Forums. I'm sorry to hear that you are facing connectivity problems while trying to connect in spades to MSN on the computer.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.

  I would like more information about the issue.

  1. What is the exact error message?

  2. what browser you're using connection?

  3 have there been recent changes made on the computer before the show?

   

   

  If you are using internet explorer, please follow these methods and check if it helps.

  Method 1: Verify the problem by running Internet Explorer mode without modules.

  Temporarily disable all add-ons to see if the modules are the origin of the problem.

  To temporarily disable all add-ons:

  a. click the Start button.

  b. click on all programs, accessories, and click on system tools.

  c. click on Internet Explorer (No Add-ons).

  If the Internet Explorer (No Add-ons) mode works very well then an add-on may be causing the problem. You will need to re-enable each (process of elimination) in order to determine which one is causing the problem.

  http://Windows.Microsoft.com/en-us/Windows7/Internet-Explorer-Add-ons-frequently-asked-questions

   

   

  Method 2: Optimize Internet Explorer and check.

   

  How to optimize Internet Explorer

  http://support.Microsoft.com/kb/936213/no

   

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

   

  For more information, visit the following link.

  Sign in using

  http://zone.MSN.com/en/support/article/supporthubsignin

   

   

  If the problem persists, feel free to let us know. It is our pleasure to be of service.

• I have an I Phone 5 for a month issues and have stay connected to WiFi at home, it shows plugged in to the phone, but is not, I have to turn off WiFi on the phone and then turn it back on and it's ok for a day or two, I reset

  Stay connected to home Wi - Fi issues

  If your iPhone, iPad or iPod touch connects to a Wi - Fi - Apple Support network

• Issue of Pro 6100 satellite about the RTC battery

  I know it's a huge topic which will be discussed on, and my Toshiba is screwed. I even did a lot of research and found it disappointing that my Toshiba may not be repairable, but I have a question;

  When I boot my Toshiba, it looks good, and I can run normal programs (I get the error of bad RTC battery), but for some reason, the Toshiba randomly freezes and I have to stop it after 5 to 20 minutes to use me.

  I tried to leave it on, as some other forum topics proposed to charge the bettery RTC and it went okay, then 20 minutes later, it froze and I had to reboot.

  Sometimes it is not still turn just after that I have forcefully arrested, so I have to wait from hours to days so he can go back on. But it's useless cause it hangs again.

  Any input on it's great and I'll take advice for this problem. I want the RTC battery but it keeps freezing on me, if I want to find a way to prevent this. Thank you!

  PS: ASP Toshiba Theres two locations in my city (Markham, Ontario, Canada), so if all else fails, I'll take the laptop with my father at one of these places.

  Hello

  If you want to reload the RTC battery you don t need boot up the laptop.
  You can simply connect the AC adapter to the laptop and allow it to charge for a piece of 8 to 12 hours.

  The freezing issue for me sounds like an overheating problem. This can happen because of the dust and debris inside the laptop. In such cases, cooling modules may not work correctly.
  In case you I recommend first charging the RTC battery (don t need to turn on the device), then to clean the fans (you can use carefully vacuuming).
  If the laptop freezes then you could try to reinstall the operating system.

  If all of these tips n help so you should ask the ASP for the verification of the laptop.

• RRAS issues! -Unable to connect to the VPN users,

  original title: RRAS issues!

  Hi all, I have some real issues with my RRAS VPN. All of a sudden the users are randomly cannot connect to the VPN. Making mistakes like 619 800 and so on. I activated the GRE (once the problem starts) checked to see if the 1723 port is open. Why is this happening now?

  I use DynDns host name and everything seems fine, fact that there are enough ports available to PPTP on the RRAS.

  I am running Windows 2003 SBS SP2

  Router is a MAKO 6861 with a normal ADSL line

  I see this in the PPP.log:

  [8128] 06-04 10:27:27:794: Recv timeout event received for portid = 288, Id = 5, Protocol c021, fAuth = 0 =
  [8128] 06-04 10:27:27:794:
  [8128] 06-04 10:27:27:794:
  [8128] 10:27:27:794:
  [8128] 10:27:27:794: <06 57="" eb="" 0d="" 3e="" 07="" 02="" 08="" 02="" 0d="" 03="" 06="" 11="" 04="" 06="" 4e="" |.w..="">... N |
  [8128] 10:27:27:794:<13 17="" 01="" b0="" 09="" a5="" e1="" 15="" e6="" 49="" 4f="" 85="" fb="" 7c="" a0="" 15="">
  [8128] 10:27:27:794:

  And some of this:

  [8128] 06-04 10:27:43:325: line before the end event occurred on port 138
  [8128] 10:27:43:325 06-04: FsmDown event is received for Protocol c021 on port 138
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 9, Protocol is c021, EventType = 0, = 0 fAuth
  [8128] 10:27:43:325 06-04: FsmReset called Protocol c021, port = 138 =
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 3, fAuth = 0
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 7, fAuth = 0
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 2, fAuth = 0
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 1, = 0 fAuth
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 4, = 0 fAuth
  [8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, Protocol is c029, EventType = 0, = 0 fAuth
  [8128] 06-04 10:27:43:325: LcpEnd
  [8128] 06-04 10:27:43:325: line Post event took place on the port 138
  [8128] 06-04 10:27:43:325: NotifyCaller (hPort = 138, dwMsgId = 23)
  [8128] 06-04 10:27:48:043: line-up event took place on the port 138
  [8128] 06-04 10:27:48:043: PortName: VPN3-19
  [8128] 06-04 10:27:48:043: from PPP link with IfType = 0x0, 1p1f = 0 x 0, IPXIf = 0 x 0
  [8128] 10:27:48:043 06-04: RasGetBuffer returned 58 c 2148 to SendBuf
  [8128] 10:27:48:043 06-04: FsmInit called Protocol c021, port = 138 =
  [8128] 06-04 10:27:48:043: ConfigInfo = 80260
  [8128] 06-04 10:27:48:043: available APs = 2
  [8128] 10:27:48:043 06-04: FsmReset called Protocol c021, port = 138 =

  Hello

  Your question of Windows Server is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.

  Please ask your question in the Technet Windows Server General category.
  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

• Internet connection issues "Limited or no connectivity." and "windows could not find a certificate to log on the network.

  I'm so unable to connect to the internet?

  Hello.

  I'm so unable to connect to the internet.

  Since I've renamed our WiFi network and add a WEP key, I have problems with wireless connection on my
  Windows XP computer desktop, which is a Dell Dimension 4700.

  The questions that I get connection are...

  "windows could not find a certificate to log on the network.

  "Limited or no connectivity."

  I did all the solutions I could try to fix the connection problem!

  1. once I received the message "limited or no connectivity", I click with the right button on the connection and click on repair. It is not always connect for me and I got the "limited or no connectivity message.»

  2. then, I disabled the network connection and then enabled. That no longer works.

  3. I tried to withdraw from the ordered list of connections, and it still doesn't work.

  4. I checked the driver manager, and initially the Ethernet driver was outdated and missing of its pilot. He had a yellow question mark with a black sign and yellow with an exclamation mark inside.

  5. I used DriverZone, downloaded the driver, installed and rebooted the computer after the installation of the it. Apparently, it worked. But I could not always connect.

  6 I have ensured that I entered the correct WEP key, and then adjust the settings correctly. I did it like 10 times in a row and would not always connect.

  7. I tried to go to the command prompt and typed in IP Config/All and that's what I mean.

  Windows IP configuration
  Node type: unknown
  Active IP routing: no
  WINS proxy enabled: no
  ETHERNET connection to the Local network card
  State of the media: Media disconnected
  Description: Intel PRO/100 VE Network Connection
  Ethernet card 2 wireless network connection:
  Suffix the connection-specific DNS: (EMPTY)

  8. after that, I typed the command: ipconfig/release
  and then I got this error...

  No operations can be performed on the connection to the local network, although it has its media disconnected.

  9. after that, I tried Googling for some solutions, and the solutions I found were not any use.
  A solution was

  10. opening of Services...
  Start | Run | Type: services.msc | Click OK |
  Scroll down to and double-click Client DNS | Set to automatic on startup
  type |
  Click apply | Click the Start button | When it starts, click OK
  Do the same for the DHCP Client.
  Do the same for the remote procedure call (RPC).

  and it still doesn't work.

  11. when I look in the menu network connections, I see my connection with a lock on the side, with a red X under the lock and key. In the description, I see not connected, protected by a firewall. How could I remove the internet connection firewall? I disabled the firewall and that did not work.

  12. I tried to uninstall and reinstall the network card and who does not work either.

  It is not the network itself that is the problem.  It is not the modem or the cable. There are no disconnected son or something like that. We have other computers in the House and the internet works fine on other computers. As I said, since I renamed our WiFi network and added a WEP password, I had problems with connecting to my Windows XP computer.

  My computer has updates that must be installed as well. Updates would fix the problem? I just need to have internet.

  What should I do? Thank you for your time.

  Sincerely,

  Justin

  Have you tried to set the value of the link speed/duplex mode? I had the same problem you describe. Your card is only capable of 10/100 communication.

• WRT150N wireless - download speed of connection is super slow when I move away from the router.

  I have a suggested internet high speed through Comcast, and my wired computer is get 6 download MBS. My wireless laptop is close when I'm a few feet from the router, but decreases significantly when I move out of the room - up to 200-300 KPS.

  I can't even watch a movie from netflix on the floor without stopping and buffering several times in a 1/2 hour show.

  Long-story-short: I expect too much on this Wireless N technology, or is there something wrong with my router, connection, configuration, etc. ?

  The strenth of signal on my laptop shows excellent quality for good, but the speed is terrible.

  Any suggestions / advice?

  JL

  It could be due to the wireless settings are on your router has its default value, which is the reason why you might be faced with the problem. I think you need to change some settings in your router...

  Connection to the router configuration page and then click on the tab below the Strip Radio Standard - 20 MHz and the Standard 11 - 2, 462 GHz channel change and wireless... Wireless SSID broadcast should be enabled and then click on save settings...

  Then click on the "Advance wireless settings" sub-tab and below change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...

  Now let's see if you can locate your wireless network and try to connect...

• Issues of speed and bios USB

  Dear Experts!

  I have a HP Compaq dc7600 small factor of my machine, with a unique design and the State of the housing. My question is that I use my win7 on it, but USB is not handled properly. I may be able to keep the device run faster the message, but if I know that USB 2.0 connectors, you need to use it but not at full speed. Idea?
  And another question can I post messages disappear at startup? Connected permanently front USB not display, and the chassis fan not (really they are not connected, the fans go to the thermometer to control information, before us, because you don't need kids )

  Hello donmacko,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that you are having problems on your desktop with the speed of your USB ports, and I would be happy to guide you to a resolution!

  I'm sorry, but to get your question more exposure, I suggest posting in the trade forums, since it is a commercial product. You can do it

  http://h30499.www3.HP.com/T5/business-PCs-Compaq-Elite-Pro/BD-p/BSC-271

  I hope this helps!

  Concerning

• VM issues after restore vRanger connection

  Our virtual machines are stored on a San. VRanger connection allows us to back up virtual machines. For an Active Directory disaster recovery test, I restored a few domain controllers in a single ESX server (Test Server) local storage.

  I can record the successfully the VM, but when starting the virtual machine I get an error:

  "Virtual Disk hard drive 2 is not accessible on the host: cannot access the file.

  When I tried to remove the discs from the virtual machine, I get the error "invalid configuration for device 0.

  I, ve created a new virtual machine without disks. When I try to add the existing drive, I don't see the drive. But through the ESX console are WINSCP I see the entire disk. Life and the test environment have ESX 3.4/VC2.5

  I tried to rename the files vmdk with vmkfstools - E, perhaps hoping geometry/header file would change. But I get an error ' unable to rename 'VM.vmdk': the system cannot find the specified file (25).

  I think it has something to do with the header for the disk file, but I'm not sure.

  I, ve tried manually by changing the header file, but that did not work. See below what changes, I tried to do:

  1. Disk DescriptorFile

  version = 1

  CID = 00000001

  parentCID = ffffffff

  createType ="monolithicFlat" == > changed to «vmfs"»

  1. Description of the measure

  RW 21030912 FLAT "scsi0-0-0 -VMNAME1_1 - flat hard" 0== > changed "FLAT" to "VMFS" | " Delete "scsi0-0 - 0 - | Remove the last "" 0 "".

  1. The disk database

  #DDB

  ddb.virtualHWVersion = "4".

  ddb.toolsVersion = "7300.

  DDB. UUID = "60 00 e1 C2 93 03 f3 d9-38 39 4 02 74 39 d 8 d b6"

  DDB. Geometry.Cylinders = '1309 '.

  DDB. Geometry.Heads = "255".

  DDB. Geometry.sectors = "63".

  ddb.adapterType = "free".

  I found a few forums discussions about similar problems, but no solution.

  Hello. According to Vizioncore the resolution to this is as follows.

  "Hi all,"

  Support has a updated with patches for this version.  Please contact support and ask to build the field trials

  ----

• How to increase the processing speed by connecting to another computer via USB - USB cable

  Share laptop processing power. Windows 8, Windows 7

  Hello

  I was wondering if I could increase my processing power by connecting a portable alternative to mine via a USB to usb cable. If anyone knows how I would go to do that, or if it is possible I would like to know. I searched on google but not found all the answers.
  If this can help, my laptop is running Windows 8 32-bit preview developer, and the portable alternative is running as Windows 7 Ultimate 32 bit.
  Any help would be greatly appreciated.
  Thank you very much
  Mike

  Hi MichaelSenior,

  You will not be able to increase the power of a computer processing by connecting it to another computer via a USB cable or by any other means.

  In order to increase the processing power of your computer I suggest you check with your computer manufacturer to see if you can pass any hardware on your computer.

  Example: Increase the size of the memory on your computer or upgrading the processor etc...

  Hope this information helps you.

• RV180 a drop connections about every 10 minutes

  I have a cisco rv180 connected to a cisco cable modem and a service of Cox.

  The symptoms of the problem are that all the 10 minutes or so external connections will hang.  This takes perhaps 20 to 60 seconds.  If you load a Web site when this happens, different parts of it not to load and firefox will sit and spin indefinitely (it seems) until you stop loading and click on the button reload manually.

  When that happens I can always connect to the Web server of routers and dashboard that refreshes automatically every 10 seconds.  It seems perfectly fine.  My initial theory was that something was broken at the end of things, but after swapping Cox RV180 with an old router on-q that we had laying around, we have not seen problems.

  Other differences I noticed between the on-q and the rv180:

  * with the traceroute for external guests rv180 lagging large (500-600 ms) to the hop right after the router.  With the on-q, it is 12ms.

  * When I ping the ip of that jump with great delay, with the on-q, I don't get any answers.  With the rv180 that I would get these host redirect strange messages that make it look like that ip redirects to itself.  There will be 1 or 2 of those redirect responses, followed by 3 or 4 errors, and each packet is numbered as an error in the summary of ping.

  Anyone have any ideas of what to try to debug further this problem?

  Thank you.

  -Aaron

  Aaron,

  Go to firewall-> attack check and uncheck all the options. If that helps start checking things and see if any of the options causes the problem. You must also test MTU:

  http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=386

  You may need to change the MTU on the WAN port to something else than 1500 (default)

  I have a RV180W connected to a DCP3010 on Charter cable and it works PERFECTLY. I replaced my old modem, Docsis 2.0, which was having some problems.

  Keep us updated.

  -Marty

• Weather gadget issue, error: ' unable to connect to the service.

  Original title: weather gadget problem

  I am running Windows 7 and I'm trying to change the weather gadget in my city.  I typed in my zip code, it recognizes it, but says "unable to connect to the service.

  Until I received this suggestion I solved the problem by uninstalling the weather gadget and download another.  He worked after doing this.  I checked the regional and Language Options, and they match.

  Thank you.

• New issue of electric power connection

  I just replaced my PSU with a coolmax v500 and new connections to the motherboard came with the additional connection 4 pins. The original power supply had not well that the motherboard has 14 pins decision-making

  My question is this. Can I plug the 4-pin or leave it disconnected? Currently, I have not plugged and everything works fine.

  Thank you in advance for your help!

  Steve

  HP A63133W

  Steve, if you're talking the main ATX power connector, it's 20 pins or 24 pins, like you said.  If it's the 24pin, you would connect the connector 4-pin.  If it's the 20 pin, you don't connect it.

• VMware VC 5.5 first issue of permission to connect, please help

  

  Also, vsphere 5.1 from the SSO is required to connect.

  In vSPhere 5.1 it is administrator@system-domain

  5.5 the user name is: [email protected]

  PLEASE CONSIDER the ASSIGNMENT any USEFUL or GOOD answer. Thank you!!