javaw.exe missing on view Security Server - view 6.2.1

Similar Questions

• View security server 404 error - access external Office

  Hi all

  I am a security view in our gateway server deployment and for purposes of test base, we use a self-signed on view security server certificate.

  We are trying to access the external address and the following error.

  

  When you view the web address, we see the following error.

  

  The current set in place is that https traffic (443) intervenes, it strikes at our front door that transfers the SSL and port 80 traffic hits the view Security Server.

  I suspect that this could be a sort of issue of the certificate, or a configuration parameter missing.

  Any advice would be much appreciated.

  Thank you

  Gary.

  I wish that I could provide more assistance, but I do not have an F5 and yet I found the deployment guide that you have already gone through.  The section with the changes necessary for starting servers F5 and safety on page 8.  The only thing that caught my attention was that you need to configure the file locked.properties for servers that require http

  http://www.F5.com/PDF/deployment-guides/VMware-view5-IAPP-DG.PDF

• PCoIP Raccordementvia security server view Horizon 6.2.1

  Given the problem with connecting to the office via a security server view VDI.  She starts to connect, is a black screen for about 10 seconds, then disconnects.

  This is my setup

  All ports are two-way.

  Public IP address is NAT for the Security server in the DMZ.  I have TCP 80, TCP 443, TCP & UDP 4172 open ports on the Security server.  (I tested by telnet to the public IP address on 80, 443, & 4172.  It works)

  From the Security server in the DMZ, I ports TCP 4001, 8009, 4172, 3389 UDP 4172 open from the Security server to my login server in-house.

  From the Security server in the DMZ I have ports TCP 3389, TCP and UDP 4172 open for VDI desktops.

  I am able to connect to computers correctly using the server for internal connection on PCoIP.  It is only on the Security Server I'm getting the black screen problem.

  Any ideas?

  I found actually just the problem.  I had to activate the secure gateway PCoIP and I had to enter the public IP address and the port 4172.  Initially, I activated it and he used internal connection server address it and it did not work so then I changed it to the IP address of the DMZ security server and it still doesn't work.  While I was reading upward on the setting that I saw that had to be the accessible public address.  Once he did that, he started to work!

• One of my view security server shows as "unknown" in Administrator dashboard view

  Hello

  One of my view security server (view Horizon 5.2) shows as UNKNOWN in Administrator dashboard view.

  I tried with the declared, rebooted Server services restart, still no luck.

  The stated server is accessible via RDP and the Services are running.

  Can someone help me on this?

  This problem has been resolved by disabling Windows NLB NETWORK adapter settings.

  We used Windows NLB long back for security servers, recently we removed view Security Server NLB Windows and place in F5 load balancing.

  Not sure for some reason, the Windows NETWORK load balancing service came active, disabled, and the problem solved.

• View customer Horizon | Unable to login via the Security Server

  Hello people,

  We strive to deploy VMware View 5.3. Everything is complete we are able to access desktop of customer view through connection to the server. But when we try to connect to the desktop via security server, authentication of the user position get us the attached error.

  Can someone please help me to understand and resolve the error?

  Thank you!

  Hari.

  Thank you for your response. Issues was DNS resolution external URL referred to the client device. We decided. Thank you.

  Hari.

• Unable to connect to view Security Server 5.0

  Use vmware view client build horizon 2.1.0 1213173 (ubuntu 12.04 64-bit), when I tried to login (local network), I got timeout message

  I can connect if server connection hollow instead of security server connection

  one mistake that I find on security server is 33, SideBySide error

  no errors not found on the page of the web interface of the login server events

  Here is the output of scan nmap from client to server security

  from Nmap 5.21 ( http://nmap.org ) 2013-11-06 15:13 MYT

  Scan nmap for view.cnc.net.my (10.1.1.20) report

  Host is (0.00017 s latency).

  Not shown: 988 closed ports

  SERVICE OF THE PORT STATE

  53/tcp open domain

  80/tcp open http

  135/tcp open msrpc

  139/tcp open netbios-ssn

  443/tcp open https

  445/tcp open microsoft-ds

  3389/tcp open ms-word-serv

  49152/tcp open unknown

  49153/tcp open unknown

  49154/tcp open unknown

  49155/tcp open unknown

  49167/tcp open unknown

  MAC address: 00:50:56:87:35:FF (VMware)

  Do not check everything again: you cannot log in because you can't solve. It can be solved, either replace the connection URL in the configuration of the IP address instead of FULL domain name, which I do not recommend since the certificate cannot be based on IP addresses...

  When you receive a message "Server (null)", it is because the server name cannot be resolved by the client. The reason why you configure server security <->Server with IP addresses tunnel connection is because they may not be able to resolve the FULL of the other domain name.

  The PCoIP gateway feature is enabled on the servers of your connection? It may be useful if you send us pictures of your configuration (security servers and connection)

• View heavy client work - but the HTML is not - using security server

  However, I better start a new thread after the marathon to get the heavy customer talk via security DMZ server... everything works fine now.

  I am now test HTML experience via the same security server... and get quite like I was getting with the thick client.  I cross any authentication, it says connection to the office and that's it.  Later says that the server has taken too long to respond.

  I now have a complete list of the rules of the firewall in any way.

  Clearly port 8443 is open from the Internet to the DMZ security server.

  I checked the rules and scanned, and apparently they let all ports open between the DMZ and internal both directions in our network...   I checked and 22443 is open on the desktop...

  Can someone tell me what I should look for the next please?

  Thank you

  Bill

  Make sure you go through all the steps exactly - config http://www.vmware.com/pdf/horizon-view/horizon-view-html-access-document.pdf

• VMware View 5 Security Server

  Hey guys,.

  I have a problem with the Security server. I have installed A Windows Server 2008R2 in the DMZ.
  To install the view security server, the Win2k8R2 must be in the field. This does not work because the server is in the demilitarized zone. How can I get the server to the domain?

  Without doubt, I need to open ports... But wich ports i open?

  and is not a security risk to open ports on the DC?

  Or is there another option?

  Best regards
  Best regards

  There is no requirement for a security to a member of the domain server, these controls was only for the connection to the server or replica server role when you run the Setup program. You will need various open ports for connection server that you are to match, those that are detailed in the documentation under https://www.vmware.com/support/pubs/view_pubs.html

• Requirements VMware View 5.1 Security Server RAM

  Hi all

  I understand that the view connection Server 5.1 needed at least 10 GB of RAM for the deployment of desktop 50 + and I also received this tip of the engineer to Support VMware to use at least 10 GB of RAM when installing the CS for the first time, then we later, the performance problem.

  Now, my question is how on the Security Server?

  Based on the VM docs, they all (CS, transfer, SS) must have the same hardware configuration, but I don't know about the Security Server why would he needs 10 GB of RAM. The CS needs a grand RAM size due to the Virtual Machine Java 2 GB but is SS has a JVM too?

  According to your experience, will be a 4 GB enough RAM for SS?

  Thanks for the comments!

  Server security uses the JVM too.

  At least 10 GB is recommended for the connection to the server (including the lines connect to the server and security server). See table 1-1 on page 8 here http://pubs.vmware.com/view-51/topic/com.vmware.ICbase/PDF/view-51-installation.pdf

  Mark

• VMware View Security Server DMZ

  Hello!

  We are currently developing a small installation of VMware View in our office as a CEP and I have a question about the server security and the need for the ports against customers.

  Our facility:

  (Active Directory and RADIUS) 2-factor authentication

  Front End FW

  Security on the DMZ server

  Backend FW

  Connection to the server

  The question I have is:

  4172TCP/UDP port 3389 be open from the Security server to customers?

  Is there no way of this tunnel since the Security server through the connection to the server on the inside?

  Thank you

  Kenth

  Hej Kenta.

  You are right, there is currently no way to tunnel on the dry-server and the connection broker using PCoIP, you can only create a tunnel through one.

  So that means you need to open TCP/UDP 4172 between dry-server and desktop computers-view.

  Joel

• VMware View 5.1.1 Security Server LDAP errors

  Im having a serious amount of errors on my VMware View (5.1.1) security server

  Log debugging shows a large amount of LDAP errors, see below.

  2012-09 - 06T 10: 46:49.075 + 02:00 ERROR (0610-0940) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 11: 01:50.102 + 02:00 ERROR (0610-0CB8) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 11: 16:50.109 + 02:00 ERROR (0610-0FE8) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 11: 31:51.120 + 02:00 ERROR (0610-0DD8) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 11: 46:51.132 + 02:00 ERROR (0610-0244) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 12: 01:52.159 + 02:00 ERROR (0610-0F3C) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 12: 16:52.155 + 02:00 ERROR (0610-0E5C) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 12: 31:53.182 + 02:00 ERROR (0610-0F68) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 12: 46:53.194 + 02:00 ERROR (0610-092 C) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 13: 01:54.217 + 02:00 ERROR (0610-08E4) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE
  2012-09 - 06T 13: 16:54.227 + 02:00 ERROR (0610-0504) < WSAdminDomainTimerThread > [ws_admin] cannot bind to LDAP://rootDSE

  Anyone got any suggestions?

  Hello

  The plugin ws_admin trying to make field checks every 15 minutes, but given that your security server is not on the field these checks fail. It is completely harmless, but they should not run in first place, I raised this in their own country.

  Mike

  Edit:

  There is a simple solution for this in 5.1.x:

  Under the current registry key HKLM\Software\VMware, Inc. \VMware VDM\plugins\wsnm\admin, create a new key named Params, and under that a new DWORD value named InitiateDomainChecks with 0 data. Once set, you will need to restart the VMware View Security Server service for the change to take effect.

• I'm a little confused on what view "Security Server" is...

  I configured a test of internal company environment VMware View 5.1 to access pooled VMs dedicated and linked clone of iPads.

  Now, one of the users involved in the test environment wants to access his VM dedicated outside of the office... But I want to be sure to provide a secure connection.

  I was a little confused with the VMware documentation, because I understand that VMware View 4 had another product/device to view security server to act as a gateway, secure to operate into DMZ network and enable access to the view connection server... I think so... But I find no such beast in VMware not downloads section called 'VMware View Security Server 5.1.'

  I'm in a bit of mess. My understanding on Internet clients see how external access to the server of company internal connection through the DMZ must be leaves much to be desired unless 5.1 view connection server itself has absorbed the activities of the Server VMware View 4 security and he is riding on the area demilitarized or well... Oh hell... I'm just confused

  Little help or a point in the right direction would be greatly appreciated!

  See you soon!

  Keegan

  To install the Security server that you use the same installer regarding the Connection Broker, its an option during the installation process.

  Linjo

• Extra license is required to view security server

  Hi, we have a Vmware Academic View4 first bundle only this configuration of a server to view security or additional license coverage there?

  Thank you

  Robert

  No additional license is required to see Security Server. It is included in the General view license.

  Mark

• Peripheral NAT between Security Server and Connection Manager - View 4.6

  Hi all

  I'm trying to deploy a view environment 4.6 - with a view Security Server in the DMZ.

  The DMZ is a NAT entirely would be and isolated network (single firewall, configuration 3-leg-GB-2000 is the model of the firewall).

  
  At this point, just trying to get RDP to work with this configuration.

  The firewall configuration is as follows:

  -Security server IP - 10.1.1.49/24

  -The alias created to view connection server - 10.1.1.100 (NAT IP)

  -Tunnel NAT (with port 8009 and 4001) created between the server connection view and real IP 10.2.2.229 server connection alias

  -The alias created for the view Desktop - 10.1.1.101 (NAT IP)

  -Tunnel NAT (with port 3389) created between Desktop and view real IP Destop 10.2.2.239 view alias

  I can RDP directly since the Security server to the desktop (via the 'alias' 10.1.1.101 IP) view correctly.

  I can connect successfully from the internal network (via IP real office 10.2.2.239).

  When I try to connect via the server of security (from the outside) I get the connection for the initial connection manager, and I choose the pool to connect to. However I'm unable to start a desktop session. The error I get is "the office is currently not available.

  In the event logs on the Manager server connection that I see that the real IP (10.2.2.239) is used to connect to the desktop view - which will not work in this scenario (the 10.1.1.101 alias should be used).

  Has anyone deployed a server of security seen in this scenario?

  Thanks in advance!

  Not sure if it works or not, but there is a GPO that changes the rules to connect using the DNS name.  Is the name DNS returns the correct value, you must connect as?

• Unable to connect to the host via VMWare View Security Server 4

  I have installed and configured the VMWare View connection server and can connect to the virtual machine (Windows XP Pro) shareed via the customer to view without a problem. The problem Im having is that I have configured the Security server in my zone demilitarized and authorized the appropriate DMZ ports and the port 80 and 443 to the outside on my DMZ. Access the public URL and he invites me to authenticate what I do and it then publishes my office pool. I click to connect to the shared pool and it says connection for about 5 drops of s and then just my connection. Now, if I go to my security on my DMZ server, I can connect to the thin desktop via RDP.

  Thank you

  eeg3 is correct if you have a direct connection enabled on the broker for connections paired with security server then you would be forced to open 3389 to the outside world since the workstations would try to connect directly to the desktop.    The right way to go forward is to create the replica with disabled direct connection and combine security with this box server.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points