Similar Questions

• Management and vMotion have the same IP address

  Being quite new to ESXi I have spent hours to deceive and reading and do not understand why my management and vMotion interfaces have the same IP.

  The configuration is the following:

  Cisco UCS blades

  8 cards per blade

  vmnic0 and 1 - management

  vmnic2 and 3 - vmotion

  vmnic4 and 5 - IP storage

  given the VM vmnic6 and 7-

  I installed and the management network has migrated to a DVS without issues.

  Now when I create the DVS/port group for vmotion and assign the IP address I met 2 problems as you can see in the screenshot attached the blade/network.

  Thanks for any info.

  P.S., Management and vMotion are on different networks.

  Yes, the ESXi host may have a default gateway. It is used only when a vmkernel must be routed traffic.

  In the case of vMotion - as long as your vMotion enabled vmkernels are all on the same subnet and VLAN, the default gateway will never serve.

• MBPro stops during startup.  If I continually move the mouse during startup, it will go on my desk.  If I launch Firefox and try to do anything, it stops.  This can be corrected?

  Mac Book Pro stops unexpectedly during startup.  I can get it to go to my office, if I continually move the mouse during the boot, but after I launched Firefox and try to do anything, it will stop.  If I try to run the scans of security or reinstall OS X using the command + R and disk utilities, it stops.  Sometimes it gives me a box saying something about stopping with various options such as Cancel, stop, reboot, etc., but it makes no difference that I click on, she stops.  Sometimes, I get no warning at all.  This can be corrected?  I'm not savvy Mac.

  Reset the SMC could solve problem then.

  Reset the management system (SCM) controller on your Mac - Apple Support

  Also try the safe mode boot.

  Try safe mode if your Mac does not end commissioning - Apple Support

• I looked in the addons Manager and I seem to have 5 versions of java installed console, do I have all or can I disable all, but later?

  I see 5 versions of the java console addons, 6.0.04, 6.0.07, 6.0.10 6.0.12 Manager and 6.0.14.Do I need all these or should I disable all, but later?

  If properly uninstalled plugins for Adobe Reader and Foxit Reader should also uninstalled in the process.

  Be careful with the Windows registry, unless you know what you're doing.

  • Always back up the registry to another source; not the current hard drive.
  • Use a program that will offer to back up the registry keys that you delete.
  • Always have a boot disk (CD/DVD, USB key) just in case you make a mistake.

  You can use Windows search to locate the plugin files and delete them if they are on your hard drive and leave the single registry. Find and delete the following files while Firefox is completely closed. After you delete the files, launch Firefox, look at your plugins, addons > Plugins, to see if the two plugins are gone.

  • The Adobe Reader plugin name: nppdf32.dll
  • Foxit Reader plugin name: npFoxitReaderPlugin.dll

  A few links for you to watch:

  1. Foxit Reader:
     • http://www.foxitsoftware.com/support/showfaq_technical.htm
  2. Adobe Reader:
     • http://kb2.Adobe.com/CPS/400/kb400769.html
     • http://www.Adobe.com/cfusion/search/index.cfm
     • http://kb2.Adobe.com/CPS/836/cpsid_83690.html

• HP Laserjet Pro M201dw: "then I explained the problem to management and they said not to buy all the HP printers more."

  Our two new printers Laserjet Pro M201dw are not recognized on the office network.   I have spent hours trying to understand this and posted questions on the forum Support HP, but without response. They became more disadvantages than thay are worth.  And that's enough.  Then I explained the problem to management and they said 'don't buy it not all HP printers more.'

  Thanks for the suggestions.

  I tried to BootP and disable ipv6 on a printer and at first, it worked (finally).  But then, after having unplugged and restarted, he returned to the ip address of connection no.

  So finally, I noticed and changed the setting of the link of "Automatic" to '100TX' speed full - and that seems to have solved the problem of intermittency.  I've converted and turn it back on, unplugged, etc., and it maintains the connection and ip address.

  Do not want to play with something that works, I can't say with certainty if the speed of one link would have solved the problem (probably not), but it seems that while your excellent suggestions finally established a network connection, the setting of explicit link speed was necessary to maintain the connection.

  Thanks for your help in this matter!

• Launch Manager/media button Driver Windows 8

  Hello

  I have an Acer Aspire 5742. I recently reinstalled my Windows 8 (64 bit) OS and I need to reinstall all my drivers. I have trouble finding the driver for my fn keyboard media buttons. In the past, I think the driver for this was called the "Acer Launch Manager" driver, but I can't find a similar driver for Windows 8. Any help direct me to a driver of job (for an earlier version of Windows maybe?) would be greatly appreciated!

  Thank you!

  Mati,

  Thanks again for helping out. I went into the BIOS and that has not worked, so I instaled Windows 7 Launch Manager driver and who seemed to have done the trick. Not sure why the driver of Windows 8 was not functional, but fixed now.

• Indicator of Caps Lock Launch Manager

  I downloaded and installed the latest Driver Helper button RF and Dritek Launch Manager Acer Web site. I have an Aspire V5 - 471g (Windows 8 single language) and it cannot warn me if I pressed the Caps Lock key or trigerred the NumLock and scroll stop.

  There is no cap lock indicator in windows 8 as you have had in win 7 with launch app Manager.

  Please see the Tower from below link for another job.

  http://Acer.custhelp.com/app/answers/detail/A_ID/30035/kW/Cap%20lock%20indicator%20win%208

  also, you can use any third-party lock, numb lock indicator software.

• Windows Movie Maker "the file is protected using digital rights management and cannot be imported."

  I downloaded a large .wmv file last night and have to divide into 8 smaller parts, but when I try to "import media" in Movie Maker is stipulates that "the file is protected using digital rights management and cannot be imported.

  Is it possible to import the file to edit?

  Turnbite removes the DRM http://download.cnet.com/Tunebite/3000-2140_4-10783040.html but I still don't know if it would work with Movie Maker (only because I haven't used products - looks like it would work, but I'm not sure).  Here is a review of version 6 (the current version is 7): http://mp3.about.com/od/audiotools/fr/Tunebite_6_Rev.htm.  Apparently, he's copying your DRM files and so it is required to have at least some degradation (but not a lot from what I've read - not noticeable).  Because it's free, it can't hurt to try it and see if it solves the problem.

  AVS looks like he got a number of good products http://www.avsmedia.com/, but I don't think that one of them address the DRM issue.  I really didn't listen to music or watch videos on my PC very often so I'm not familiar with the products to do such things.  May I suggest you post your question in the music and its Forum: http://social.answers.microsoft.com/Forums/en-US/vistamedia/threads , where issues of music specialists will be more than happy to help you with your questions.   Or in the photos and video Forum at: http://social.answers.microsoft.com/Forums/en-US/vistapictures/threads where the video specialists will be happy to help with you project of filmmaking.

  As for Shane Childs, I suspect that Karthik copied an answer, he used for this person to respond to your question and everything just forgot to change the username - just a typing error.

  Good luck and I hope this helps. Lorien - a - MCSE/MCSA/network + / A +.

• What is superfetch? Its in my sTask window manager and he uses a lot of CPU power... .do I need it and what is?

  The program is placed in my Windows Task Manager and takes a lot of CPU power, and I wonder what use it perhaps can cause? my CPU usage was 100% and my antivirus uses only 5%.

  "Superfetch" and "The host Windows Services" take so much CPU power on i3, 3 gb Sony Vaio!

  SuperFetch is a Windows service that is designed to accelerate the launch of the app by preloading some applications based on your usage patterns. Tune-up blog has a good explanation of what it does.

  However, it should not be maxing out your CPU all the time. If it slows down your computer, you can try to disable it.

  To turn off:
  Open the Start Menu.
  Type "services" and press ENTER.
  SuperFetch. search in the list and right click > properties
  Set the startup type to disabled, and then click the Stop button to stop the service
  Click Ok

  You want to make sure that your antivirus software is up to date and your computer is clean.

• Internet being interrupted and double IP address conflict

  I have a dell Inspiron 580 - 6 GB ram - Intel I5 cpu hard drive - 500 GB - windows 7 Home Premium 64-bit OS.

  In the last week, I noticed an intermittent loss of internet connection.  This produces every once in awhile my ISP and 15 minutes later everything is ok.  However, now, sometimes 2 - 3 times in an hour - several hours pass without problem and then it happens again.  ISP called and they don't report any specific problem in my area.    I have a desktop computer and a laptop (laptop is an HP with the same operating system as an office, but with an I7 processor).

  In the search to make sure that all cables have been sure I noticed that my Cisco Valet router was turned off completely but then less than a minute it must have been restart itself as well as all the lights began blinking after a few minutes the internet connection was back on.   Several times during the day, the same event happened.

  I also noticed that a few times during the day that I received the message that "another computer on the network has the same IP address as this computer."  The same message appears twice on the laptop and the desktop.

  During this same period, I noticed that the mouse wireless for Office behave erratically - IE. trying to close a browser tab or even a windows control panel - nothing occur up to what I had clicked 6 or 7 times on x to close the window.   It was like when you're first start is a pc and you try to click on something, but the pc is still very busy to fill the trunk and clicking on something does not have an immediate response.  I went into the Task Manager and did not see the elements of high cpu utilization.   I changed the batteries in the mouse, but the problem continued.  I got the wireless station that receives orders from mouse - re hooked and then the mouse worked.

  I just mention that I'm not a patellar believer in coincidences, especially technical problems that appear at the same time.

  I checked all my windows updates are up-to-date and they are - also in the history there is no update is unsuccessful attempts.

  Then, I checked for viruses or malware.  I did a full scan with Norton Internet security - all definitions have been up to date - no problem.  They ran Maalware bytes and once again no problem.

  I went into the Device Manager and devices that all reported working properly.

  If anyone has faced a similar situation and has any suggestions I'd appreciate your comments. Thank you.

  Hello Carl,

  Thanks for posting your question on the forum of the Microsoft community.

  I appreciate your efforts to resolve the issue.

  I would like to know some information about the problem so that we can help you better.

  Have you made any changes to your computer hardware or software?

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If this does not help, then use method 2.

  Method 2:
  Please use the suggestions provided in this Microsoft article knowledge based and check if it helps.
  Reference:
  How to reset TCP/IP using the NetShell utility
  http://support.Microsoft.com/kb/299357

  Please refer to the section "Let fix me it myself" of this article.

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Lack of Smartphones blackBerry and eception exception address book...

  Hi all

  My wife just bought a "BOLD" and we have some questions. The first came as "eception exception - java.lang.NullPointerException" and the second was a missing address book.

  Here's a little background. My wife uses a MAC and we were able to get contacts to synchronize using PocketMAC. However, after the power off after normal use and backup starts, we have received two errors. Under contact options, it says there are 68 contacts, but none show. I tried to re-synchronization, but nothing. I checked the device using my PC and the office for the address book Manager and it does not show under backup/restore, advanced, database of the device.

  Someone has an idea what is the deal?

  Thank you in advance.

  Thanks to everyone who responded and saw the post. Late last night, after having talked to a few people and read all the posts, I thought it would be best to wipe the device and start again from factory settings. So far, wipe the device seems to have solved the problem.

  My best guess for the cause of the problem was a defective popular third-party application. I came to this conclusion because I have not tried to download or load this application since the wiping device.

  Thanks again for all the advice.

• Creation of vMotion, management and iSCSI

  Hi all

  I have doubts that I'd like to have some clarification.

  First vMotion and traffic management.

  I have two network cards. My question is, should I create IDE oucederomsurlesecondport VMkernel for each one (and adding the vMotion Option and management traffic) adding a different IP address for each and put the two in a vSwtich but the example; an active nic1 for vMotion and nic2 Eve and the management of the same traffic, nic2 active and standby nic1. With this, I have two different networks, but by using two NICs in case of failure.

  Or create a VMkernel and activate them both on the same VMkernel and put the two active network cards.

  What is the best choice, or the best performance?

  I have 6 guests on this cluster, so I need to do this in on the hosts.

  First I use QLOGIC

  The iSCSI side, should I use VMkernel Port binding? Or just use a normal VMkernel with my wihout VLAN iSCSI definition of any Biding VMkernel Port on iSCSI Software adapter?

  I have both running, but do not know which is the best way to get the best performance.

  Thank you

  JL

  Nice day!

  In summary, you should do something like that.

  vSwitch0 - Mgmt & vMotion

  ====================

  vmk0

  --------

  Management

  Uplink 1: assets

  Uplink 2: Passive

  vmk1

  --------

  vMotion

  Uplink 1: Passive

  Uplink 2: Active

  vSwitch1 - iSCSI

  ====================

  vmk2

  --------

  iSCSI traffic

  Uplink 3: assets

  If you only have an uplink for iSCSI traffic, you don't have to set up the binding of ports.  iSCSI ports is for the multipath.  If you only have one NIC for iSCSI, you cannot have MPIO.  You need two or multiple NICs or uplinks to the multipath.

  Now, for the management and the links of vMotion, I suggest using only an asset and a liability for each type of traffic.  Although vSphere 5 has the multi-NIC vMotion functionality, the idea of separating vMotion and traffic management is to separate vMotion and its important traffic in your management traffic bursts, which happens to include your traffic HA (also important).  You have certainly not * have * to set it up like that, but maintaining vMotion on his own physical link will keep walking on your management traffic.  In the case of a defective cable, I'm sure you would rather a cluttered link as no management or vMotion traffic.

  All the best,

  Mike

  http://VirtuallyMikeBrown.com

  https://Twitter.com/#! / VirtuallyMikeB

  http://LinkedIn.com/in/michaelbbrown

• In older firefox if I stop firefox.exe to the Task Manager and start firefox it will restore all my open tabs, now it doesn't

  usually in the earlier version as 28, so I end the process "firefox.exe" task manager and run back the firefox, it will restore the tabs normally I opened (websites that I had until I stop the firefox.exe)
  But now that more recent versions, not give me this feature, restore session screen becomes white and I drop my open sessions.
  I have to use the history to restore the sessions that I lost,

  Please can someone take a look at this problem, it would be an interesting option to stop the firefox.exe in the Manager of tasks and able to restore all the sessions again

  I have attached a picture for your information

  Thank you
  regarding

  Unfortunately the image have no download, but there are built in the back of the inverter session. If these do not work correctly, we are happy to investigate.

  • The problems of Firefox in Mode safe

  However, there is an addon that helps with backups called session manager Session.

• I have install an add-on for Firefox, but it does not appear in my list of Add-ons Manager, and after I restarted Firefox, it went.

  I try to install 1-Click Youtube Video dDownloader, which is supposed to add a download button to Yuotube video pages. I go here:

  https://addons.Mozilla.org/en-us/Firefox/addon/1-click-YouTube-video-download/

  and I click 'add to Firefox '. It gives me the window "install now". I click on 'Install now' and it is said that Firefox has to restart and it will be installed when Firefox opens again. If I click "Restart now" and restart Firefox. Then I go on Youtube, but no button. I check the page of the Add-ons Manager, and I see that it is installed in the extensions. So, if I go to the page and click 'Add to Firefox' once again and restart once again, go to Youtube, the download button IS there, and it works perfectly. But if I exit and restart Firefox, the download button is once again absent, but the extension is always installed. Why this extension works only when I restart twice, and then it disappears again?

  When the button does not appear, but the extension is marked as active, try to reload the page to Youtube without using the cache by pressing command + shift + r to see if that triggers the extension to insert the button.

  If it remains inconsistent, I would like to ask the developer to Add on to their Contact page: http://www.clickvideodownload.com/contact.php

• Why Apple can't do two systems? First of all, we are protected, and the other is free just like android, but in the style of the iOS and Apple needs a request so we can manage and see new products from an application and do not go on this site!

  Why Apple can't do two systems? First of all, we are protected, and the other is free just like android, but in the style of the iOS and Apple needs a request so we can manage and see new products from an application and do not go on this site!

  and I don't know that if Apple make a system more freely, there no need for any device on Earth but iPhone.

  http://www.Apple.com/feedback/