Lack of drive DVD Vista - Oh, no it's not!

Similar Questions

• driver DVD update and there but does not work

  My HP laptop DVD player does not work properly. When I try to update the driver, it does state that it is updated and currently, but it will not allow the DVD player function. When I check the peripheral material, it gives an error CODE 19.  It says that the drivers do not work properly.  I tried to allow the installation of HP Assistant driver and everything imaginable but nothing helps.

  It ends up being a higher filter problem in the registry to have two software for DVD.  It's corrected now.

• Drive DVD Toshiba on Satellite U300 does not

  I have a new Sat U300 and the Toshiba DVD player refuses to work, the message is that a module is missing.

  Any ideas?

  Hello

  WHERE´s the problem. Uninstall the current version installed, and then reinstall the Toshiba HD-DVD player. It would be best if you look at the [Download Driver Toshiba Site | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp] updates to this program.

  If this is not enough, all your backup files and perform a full system recovery, which should really help.

  Otherwise, give a few comments here.

  Good bye

• New hard drive installed Vista Ultimate, now I can not install my printer - why?

  Computer Dell laptop hard drive replaced (warranty) with Vista Ultimate, I installed Office 2007 Professional disc 1 fine, windows update is fine, but I cannot complete the installation for my Kodak printer disc. Has been given the Internet to install via the internet address - link doesn't work either - drive flashing green bar "installation preparation" then nothing? Link Web shows 'Preparing to install' with a full bar green - then stuck there. A few minutes later, he disappears. Never installed. Do not open the drive or cross the bar - never open the Green window to install. Support Kodak decided that I was missing the .net on pre-installed OS HDD framework files. Enough of 3.45 and 4. Is this correct? Do I need previous versions, or something else is the cause. How can I check to see that all the files are correct and understand WHY I can not INSTALL MY PRINTER?

  Until the hard disk, memory & the keyboard have been replaced by the Dell tech, I had installed and printed on this Kodak printer for 9-12 months. Suggestions welcome.

  Hi LSMama,

  (1) you get an error message?

  (2) what is the model number of your printer?

  There could be several causes for this problem, try the following steps:

  Step 1: Run the troubleshooter printer available in the link below and then check

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Step 2:  Clean boot the computer and then try to install the printer

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************

• Satellite X 200-15 k - how can I activate the advanced buffer HARD drive under vista?

  How can I turn on buffer advanced performance HARD drive under vista? This option is not available for this drive?

  * Check this box: *.

  1. right click on the computer in the Start Menu, then select Options.
  2. click on advanced on the left system settings.
  3 select the Hardware tab in the System Properties window.
  4. click on the Device Manager button.
  5 expand disk drives.
  6 right-click on a hard drive under disk drives, and then select Properties.
  7. Select the policies tab in the Properties window for the device.
  8. check Enable advanced performance.
  9. click OK to save the changes and reboot your computer.

  If this is not possible then the buffer of advanced performance is not possible with this HARD drive.

  Hey Buddy

• Satellite A300D-17Z - cannot install the display driver for Vista

  Hello

  There is a big problem with my A300D-17Z.

  The laptop has ATI HD3470 Hybrid Crossfire display system. I'm trying to install the driver in Vista Ultimate, but it does not work. The ATI Catalyst control cannot install and ATI driver file is empty. Shows Device Manager still there are two graphics card with «!» I tried so many ways. Install framework 3.5, pilot of the AMD 7 series, last version of the ATI driver, driver of the same other computer brand who says that worked.

  Please help me, I had been tormented for nearly 48 hours. PLEASE, I BEG YOU!

  Hello!

  Have you tried to install the driver to display on the Toshiba site? You can find it here:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Before you try to install a new display driver, you must remove any old version in Add/Remove programs. Then, restart the laptop and use CCleaner to clean the system. Restart again and then install the new version.

  You have the same problem with the factory settings? In the worst case, you must reinstall Windows using Toshiba recovery disc.

  Good bye

• Cannot format drive DVD - Rw with Windows Vista.

  Cannot format drive DVD - Rw with Windows Vista. Download "Windows cannot format... or is unable to complete the format.  Something like that. See a solution with Windows 7, but I use Windows Vista. Help?

  Hello

  ·        What is the model number of your computer?

  ·        Who is the manufacturer of your computer?

  ·        Did you format the disc earlier?

  ·        Are you trying to format the drive using windows Explorer or through third party software?

  I suggest you read the web link, below he provided information related to the formatting of disk.

  http://support.Microsoft.com/kb/930405

  Hope the helps of information. Please post back and we do know.

• Drive DVD (E) does not work in a HP Windows Vista Premium system

  When I install a DVD in drive E, nothing happens.  MagicJack is installed on the computer and using the DVD player as well.

  In the device - drive DVD/CD-ROM Drives Manager - Tiger Jet CD-Rom USB Device (MagicJack) and TSSTCorp CDDVDW TS-L633M ATA devices are listed.

  Apparently the MagicJack drive does not drive the function E.

  Registry Editor fix by removing the UpperFilter and UpperFilter and reboot, lines did not work.

  Thank you

  RBB

  Try uplugging your magic Jack for a few seconds and install it back, it can set up an another hardware profile and take a next unassigned drive letter. Or change the drive letter of your DVD drive assignment:
  Click Start-> right click 'Computer'-> manage-> click on 'Continue' on the prompt UAC-> in "Computer management" slot, click on "Disk management" "Storage". On the right pane, right click on your DVD drive and click on «Change drive letter and path...» "-> click on the button 'change... '. "under-> assign a new drive letter.

• Driver DVD WinXP for Satellite A200

  Please help people dear forum,

  I am running XP on Satellite A200.
  I went to the place on the net to download the driver for xp dvd.
  Research says: no driver available.

  Can someone please send me the driver for XP for a Satellite A200 DVD?
  DVD material is: TSST corp CD/DVGW-TS-632D

  Yes, I know the place to download.
  http://nl.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=NL

  The DVD for Vista 64-bit driver is available.
  But I do not know if it is good to use on XP (32).

  Well...
  Just install the DVD for Vista 64 driver (for 32 sound not available) and my DVD player is still not visible.
  And I guess that moderators work for toshiba, so it's fair to wonder:
  Specific no reason why the DVD for XP driver is not available? Or a more frightening question: XP still supported by Toshiba?

  Very interested in fellow computer useful to receive the DVD for XP driver first.
  And also very interested in the Toshiba answer on my question about the XP support.

  Greetz,
  Nano

  Hello

  > The DVD for Vista 64-bit driver is available. But I do not know if it is good to use on XP (32).
  Sorry, but I didn t find the CD/DVD drivers. or for Vista 64-bit, 32-bit or XP.
  Could you please tell me this driver?
  Perhaps you are which means the DVD player?

  Anyway, the fact is that there are drivers for CD/DVD don t players. Microsoft operating systems (Vista, XP) are already equipped with these drivers and generally you n t need to install third-party drivers 3rd! The STRANGE should be recognized automatically by one of the OS.

  PS: To my knowledge, this is a user forum and I don t think you can find someone from Toshiba here anyway, the XP is certainly supported by Toshiba because the XP drivers are available on the page of the driver. So I see no serious reasons why XP should t be supported. You know

  Greetings mate

• DVD - a 4 x speed CD drive DVD - RW Verbatim 4.7 GB won't record, said speed fast or slow, answers please?

  Have you tried the update of DEVICE ATA ATAPI IHAS324 Y but the software up-to-date.

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Used speed, the actual brand of discs, burning and if file Live or mastered all come into
  play. A cleaning disc can sometimes help.

  Burning a CD
  http://Windows.Microsoft.com/en-us/Windows7/help/videos/burn-a-CD

  Disc burning: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/disc-burning-frequently-asked-questions

  Disc burning tips
  http://Windows.Microsoft.com/en-us/Windows7/disc-burning-tips-for-Windows-7

  Should which CD or DVD format I use?
  http://Windows.Microsoft.com/en-us/Windows7/which-CD-or-DVD-format-should-I-use

  Format a CD or DVD
  http://Windows.Microsoft.com/en-us/Windows7/format-a-CD-or-DVD

  Burn a CD or DVD in Windows Explorer
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Explorer

  Burn a CD or DVD in Windows Media Player
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player

  Burn a CD or DVD in Windows Media Player: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Player-frequently-asked-questions

  Change settings for burning a CD or DVD in Windows Media Player
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-settings-for-burning-a-CD-or-DVD-in-Windows-Media-Player

  Burn a CD or DVD in Windows Media Center
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-in-Windows-Media-Center

  Burn a DVD-video using Windows DVD Maker disc
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-DVD-video-disc-with-Windows-DVD-Maker

  How to burn DVDs with Windows DVD Maker
  http://www.7tutorials.com/how-burn-DVDs-Windows-DVD-Maker

  Close or finalize a CD or DVD
  http://Windows.Microsoft.com/en-us/Windows7/close-or-finalize-a-CD-or-DVD

  ----------------------------------

  Excellent Forum for help with programs and CD/DVD problems
  http://Club.myce.com/

  ==========================================================

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7

  
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• My CD/DVD drive stopped working... it is not recognized on my computer... I can't open the compartment either by ejection or manually

  I have a laptop HP... I rarely use the DVD player... someone suggested the BIOS to default and disable the VRAM... Who has sense and how I would do? I tried Microsoft Fixit, but it does not work... I uninstalled the PCI controller. er in the management of devices and Rebooted, without success. It's as if my drive just disappeared.

  Thanks for any help in advance

  Hello

  To manually open the drive:

  For the readers of the status bar:

  Sometimes they get stuck. There is a small hole on the front of the CD drive that you can stick a
  a paper clip that will release him and the reader to open.

  Create a trombone in car Opener
  http://pcsupport.about.com/od/tipstricks/HT/ppdropen.htm

  Open a CD/DVD player with a paper clip.
  http://www.josepino.com/?open_cd-dvd_paperclip

  =================================

  For the readers of the slot:

  Check with the manufacturer of system on how do to eject the disc.

  Dell xps m1330 dvd drive will not eject cd inside<-- check="" these="">
  http://www.FixYa.com/support/t2643828-dell_xps_m1330_dvd_drive_will_not_eject

  Be careful as you may damage the player using the method below:
  
  You may need to get the driver to work 1 However, this could still work.
  http://www.tech-tweak.NET/2009/11/how-to-eject-STUK-DVD-from-slot-load.html

  The method used on the Mac could work
  http://www.YouTube.com/watch?v=wpWieIoBBrk

  How to disassemble the laptop (Dell XPS M1330)<--- voids="" any="" warranty!="" this="" is="" an="">
  http://ahwee.com/how-to-disassemble-laptop-Dell-XPS-M1330

  Also have heard double tape on a credit card or play can work.

  =========================================================

  For the reader does not:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.

  Rob Brown - MS MVP: Bike - Mark Twain said it right.

• Installation of Vista on the new hard drive was interrupted, and now I can not start the computer

  So I decided that I need a bigger hard drive. I got a 500 GB hard drive, so I have it PLOPPED in my Acer Aspire 5517 with my vista boot drive, turned on and began to go through the process. Once he got to the phase 'installation complete' it seems to take a while, so I let it run all night. Once I got up, it was on a black screen with the mouse, I let stand a few more minutes but still nothing. I turned off and started it expects to find to return at the beginning of the installation, but instead he began to start from what is on the hard drive at this time. It got to the screen with the loading bar and the sign 'Microsoft Corporation'. The loading bar was very frigidity and stopped and started randomly. I let it do this while I went to school, but when I got home, it was always the same loading screen. I rebooted and tried to start in safe mode, but when I do it it stops at crcdisk.sys, and never forwarded charges. I tried to do the reset thing factory start it but that doesn't seem to work. My other puny hard drive still works, but the other does not. I searched the internet but have not seen any other problem like it. I want to just start completely clean of my new 500 GB. Please help!

  Hi James,

  1. What is the number of brand and model of the hard disk of 500 GB?

  2. How did the 500 GB hard drive connected to the computer? It is external or internal?

  To troubleshoot the unable to start the issue to cause corrupted driver, some files that can not be loaded during the startup process must be fixed or restored. So, let's check the disk by using the Windows Recovery Console.

  (a) put the Windows Vista installation disc in the disc drive, and then start the computer.

  (b) press a key when the message "Press any key to boot from CD or DVD ".

  (c) select a language, a time, a currency and a keyboard or another input method, and then click Next.

  (d) click on repair your computer.

  (e) (click on the operating system you want to repair), and then click Next.

  (f) in the System Recovery Options dialog box, click command prompt. Type chkdsk c:/f to try to correct the errors.

  (g) Note: answer them when chkdsk asks you if you want to check the disk next boot Vista

  (h) after the recording of the disc, and then run sfc/scannow to check the corruption of system files.

  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.

  Check out TechNet help links and check if that helps:

  The computer starts stops at crcdisk.sys

  Help! Vista won't start... (crcdisk.sys)

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• Drive DVD RW E no longer works.

  Drive DVD RW E no longer works.

  I'm running a gateway T-1412 with Windows Vista Home Premium Service Pack 2

  DVD RW drive used to work fine, but now when I put music or a DVD in drive E that nothing happens. When I click on my computer and click on the E drive, it opens and tells me to insert a disc that has already been inserted.

  I have tried everything I can think of who isn't much so help is greatly needed.

  Thanks, Dan

  Hello

  Check with Support technique Gateway, their documentation and online drivers.

  Gateway drivers and downloads
  http://support.gateway.com/support/drivers/dlcenter.asp

  Technical support Gateway
  http://support.gateway.com/support/?cmpid=topNav

  Door Documents
  http://support.gateway.com/support/SUPINFO/index.asp?cmpid=topNav

  ---------------------------------------------------------

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burn
  and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Lack of CD, DVD in my computer

  When I open my computer the dvd cd part disappeared. I can't read DVDs CDs. Could someone help me... MissAngelina39

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• I need to format the hard drive but don't have the windows vista disc to reinstall, but have had the key code that vista was preinstalled do I have to buy a new drive for vista

  I need to format the hard drive but don't have the windows vista disc to reinstall, but have had the key code that vista was preinstalled do I have to buy a new drive for vista

  Hello

  How to reinstall Vista

  Contact the manufacturer of the laptop computer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it

  they do it for a nominal cost of $

  also ask them if you have a recovery partition on your hard drive to get back to the way you bought

  you would normally press F8, F9, F10 or F11 or Alt + F10 or 0 to start to start the recovery process according to the manufacturer

  Ask them of the exact key sequence

  or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc

  Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer

  they contain all versions of vista

  This is the product key that determines which version of vista is installed

  http://www.theeldergeek.com/Vista/vista_clean_installation.html

  How to replace Microsoft software or hardware, order service packs and replace product manuals

  http://support.Microsoft.com/kb/326246