LAG on a PC 3448 issues battery

Similar Questions

• Linking to 5524 battery battery N2024

  Dell Powerconnect 5524 can be stacked by HDMI and the newer N2024 models can be stacked by dell's exclusive stacking ports. Is it possible to connect these two fireplaces? You can connect through FPS? You can connect them through an OFFSET? What is the best process here?

  The 55xx and the N2xxx can be stacked together, except that you can treat both batteries similar to as if they were just a simple switch. Stacking basically makes only one switch, so you'd plug it comes in the same ways that you would connect a single 55xx with a single N2xxx.  If you use a LAG, however, should be split across several members of the battery cable connections.  Thus, for example, if you have a stack with three members and you have a LAG with two cables, use a port to two permanent members so that your GAL covers at least two members.  For the two chimneys creates a network more resistant, so if a member falls down the link will stay up.  In other words, if you use two ports on the same Member of the stack and Member goes down, then you have lost the connection, so it is best to divide the LAG on several members of the battery.

  I hope this helps.

  B

• Mouse and keyboard lagging

  My keyboard and mouse began trolling about a month ago.  Now latency is up to two seconds at a time. They have worked well for the first 3 years. The keyboard is plugged in and that the mouse is wireless. I am running windows 7 on a desktop computer.

  Hi whatever4507,

  Mouse and keyboard lagging may be system related issue or a device related issue. To determine the cause of your concerns, we suggest for your device to boot in Safe Mode and see if the delay occurs again.

  You can start your PC in Safe Mode by using the Advanced Boot options. To access to your computer by pressing the F8 key before the Windows logo appears. In the display Advanced startup options select Safe Mode.

  For more information about safe mode in the Advanced startup options, click here.

  If you have a mouse and keyboard trolling while in Safe Mode, your concern might be the result of recent changes, you have done on your PC. To resolve this problem, we suggest you to perform a System Restore.

  Follow the steps below on how to do a System Restore:

  1. In the dialog box of files and research programs on the Start menu, type "restore".
  2. In the list of results, click System Restore .
  3. In the System Restore window, click Next.
  4. Select the date and time (it should be the date and time until you encounter mouse and keyboard fill) in the list of restore points.
  5. Click Next, then click Finish.

  However, if you still experience the same in Safe Mode, your concern that may result by out-of-date drivers for your mouse and your keyboard. We suggest you to manually update the device drivers in Device Manager.

  For more information about how to update the drivers manually, click here.

  Let us know how it goes.

  Kind regards
  BIA of Hamilton

  You can use the mark as answer button, if this post responds to your request.

• How can I activate my HP TrueVision webcam (HP Envy dv7;) Windows 8)

  Really, I'm losing my patience here. My laptop is brand new. I remember the first time I started it, I clicked on CyberLink YouCam and the machine worked. I even took a picture with her.
  
  Since then, I try to activate the webcam and it doesn't work. I wanted to video chat on Skype but the webcam was not enabled, there is no choice of webcam.
  
  I've read that if you go on Facebook and click 'Change your profile picture' and then 'take a picture' it activates the webcam, but not in my case.
  
  When I run CyberLink YouCam, it says that he has not found webcam and if I activate it if I a.
  
  So here's my question: how to turn on the webcam? Please, give me the instructions on how it works. What I have to press the key combination or whatever.
  
  I'm the HP dv7-7202eg with Windows 8. Bought and used in Austria, if that information makes a difference :-)

  If the webcam was working before, it may be "stuck".  If this is the case, then a reset can throw everything is free and you'll be "back in business" in a few minutes.  If the reset does not fix it, there are a few more options.  Stop when it works.

  Downstairs is a Help Guide that goes over the tests and the options you have available on the software to help you solve the problem.

  This is a whole new system. If all else fails, please do call HP and ask for help!  Just because the webcam worked before doesn't mean it works now.  These webcams little are fragile and they can break - the wires are tiny and they can be crushed, twisted or broken at any time.  If the tenacious webcam does not work, call HP and ask for help.  Something may have been missed or nit can be broken!

  Contact HP

  Try this simple Reset:

  Laptops - forced Reset to solve Hardware and Software issues-battery not removable

  OR

  Laptops - use Hard Reset to solve Hardware and Software issues - removable battery

   

  =====================================================================================

  Is your driver installed?
  

  Cyberlink YouCam sp59986

  NOTE name and location -likely the *.exe file to save to "downloads".

  • Install the software / driver installation package: If you have control of "Admin", you can highlight the package and "double-click" to install, if not right click, select "Run as Administrator" and install.

  =====================================================================================
  If delivery to zero and the driver Installation bring no joy:

  • Please close all applications and restart the notebook
  • Press the switch and as Notepad starts, tap on the ESC key to enter in the Start Menu
  • Select F10 to open the Menu of the BIOS
  • Press F5 to load the Defauls (could be F9 - see the bottom of the page for the correct key)
  • Using the ARROW keys to navigate, select YES and press on ENTRY.
  • Leave the system completely load (start-up) and connect
  • Splash screen > Desktop > Windows key + X > Device Manager
  • Check the device for the HP TrueVision Webcam Device Manager

  ====================================================================================

  Update the BIOS

  You can check to make sure that your BIOS is updated to the latest version.  If needed and you decide to do, you can opt for the update of the BIOS.

  ENVY of HP dv7-7202eg Notebook PC drivers & downloads

  Update the BIOS:

  • Disconnect all the USB drives
  • Always run power cable
  • Do not touch the system while the update is in progress
  • Optional: leave wireless touch YOU, but turn off the router (make sure that there is no interruption)

  ====================================================================================

  The "Webcam all things ' for Windows 8:

  Laptop HP TouchSmart and PC AiO - Webcam troubleshooting (Windows 8)

  Good luck!

• Short term Freeze

  Mouse w/BT Envy17 - 3270nr. Computer hangs for 30-45 seconds during which there is no function mouse or keyboard. Very frustrating to have to just stand there and wait. Have tried several software updates w / no change. This happens sporadically and not that often - just frustrating when it happens. Other than this - is an exceptional computer and I am very satisfied with my decision to purchase the same.

  Ka5p,

  Continuous response to PM on the setting of external mouse Activation TouchPad - disable and enable:

  ======================================================================================

  • The best option, if it should be available for you is:

  New drivers (at least the V16.x) have the ability to disable the TouchPad / click on the keypad with a setting on the main page 'Settings' when a USB mouse is used.  This is a very nice feature.

  Control Panel > display icon > mice > TouchPad [ClickPad] settings >

  CHECK "disable the pointing device internal when the external USB pointing device is attached.

  If you want to be alerted and see a visual cue of disability >

  TICK "Animated icon in the taskbar" >

  and make sure you have your updated task bar notifications so you can see the view of the mouse.

  

  =====================================================

  Another method that may work with a driver older if the best option isn't available.

  This setting also lets you disable the TouchPad, it is to turn it off.

  Control Panel > display icon > mice > TouchPad [ClickPad] settings >

  () repeat) TouchPad settings (button) > click tapping >

  Click the shimmering blue wheel

  In "box to Disable TouchPad settings".

  CHECK "Double Tap to activate / disable the TouchPad.

  In the 'Action in the upper left'

  CHECK "Switch OFF TouchPad"

  Close

  Ok

  
  NOTE if this other option is available, it is fine, unless something goes wrong.  You could get stuck without your USB mouse AND no way to return to the setting to activate the touchpad.  I don't know if I would use this setting.

  ===================================================================================

  Dragon tips:

  If you do not disable the Touchpad (mouse) and you cannot get it back AND you do not have a USB mouse...

  You can pull the top of the keyboard on the screen with the following text:

  Windows key +U (open accessibility of) > use the arrow keys to, click on "start the Visual keyboard.

  ===================================================================================

  If all the settings are correct AND the TouchPad does not behave as it should,

  THEN

  First of all,

  • Try a forced Reset.  This forces a full disconnect and reconnect (and re-reading) of the drivers of your computer.  This could correct it if the problem is a damaged driver.  It is often the only thing you need to do with a tenacious TouchPad problem.

  Laptops - forced Reset to solve Hardware and Software issues-battery not removable

  Laptops - use Hard Reset to solve Hardware and Software issues - removable battery

  • You can try to reinstall the driver from the website of your computer TouchPad.  It is possible that the site has a newer version which could be advantageous.  Probably not if your computer is new, the timing depends on when the most recent driver for your model was released.  The facility would also replace any corrupt driver problem.
  • You can try the TouchPad Synaptics driver

  Synaptcs drivers are sometimes a little older (once in a while, catch up and forward) - drivers have the advantage that they have all the settings and the whims of the regular drivers and they work with any flavor of Windows.   This isn't a recommendation to "throw in the air.  Many people use it and they do not work.  You can always return to the local version later if you want.

  Synaptics.com - drivers

  =====================================================================================

  I hope this helps.

• Restart Powerconnect 6248 without disturbing the Configuration

  I apologize in advance for the entry-level position and if that's the answer elsewhere, please point me in the right direction:

  I inherited load on a network LAG / VLAN with a central 2-battery Dell switch Powerconnect 6248 functioning as a main switch and routing of traffic between the VLANs that are shared it resources.

  I want to restart this switch without losing any configuration, because I'm just to enter this network, I don't want to disrupt or rebuild the configuration.

  I can get Telnet or SSH access to the switch but now use the GUI. When I go to reboot I choose to restart the two batteries and am met with the message:

  "The unit will restart with the startup configuration, not the running configuration. Do you want to continue? »

  I had a contractor separate network restart the switch before and I don't know if it simply ignored the message and proceeded. I would like to be able to restart this switch without losing any configuration.

  My question is, I'm ok to move forward through this error message? Or do I need to configure backup to restart? What is the best way to proceed with a simple reboot of two chimneys, while maintaining the current configuration.

  Here is the procedure, I suggest you take.

  -If the running configuration is operational and you want to keep on the switch, and then save it in the startup configuration.

  -before to restart, save the configuration.

  -Keep the battery restart.

  You can then use this backup config as a reference in case something happens to the configuration of the switch. It's a good idea to take the habit of saving after all change config, before the updates of the firmware, reboot, etc.

  Here is an article that will guide you through the commands to perform these actions.

  http://Dell.to/1NPR5aY

  Hope you find it useful.

• camera started does not

  Hi yall. I have hp envy6-1113tx and, first of all, everything was good and after some time cyberlink, that is the camera show, had updated after that it stopped working and when I go to the camera, it's just empty. What should I do? Incidentally, I tried to reinstall cyberlink, but by a mistake, it can not be installed or it uninstalled itself

  Hi Sylvie,.

  Something to try / consider:

  • First, reset the laptop; It's a deliberate break and reconnect all drivers of material.  The forced is possible that webcam with the rest of the material.  Resetting does not affect your data or programs.

  Laptops - forced Reset to solve Hardware and Software issues-battery not removable

  OR

  Laptops - use Hard Reset to solve Hardware and Software issues - removable battery

  • Then, open the Control Panel > programs and features , and ensure that the Cyberlink software is actually "gone".  If it's still linger on, close the programs and features and remove the Cyberlink software with this program:

  FixIt - Solve problems with programs that cannot be installed or uninstalled

  • Reboot the laptop and connect...
  • Check and make sure that the Cyberlink software has finally disappeared.
  • Then, try to the Cyberlink software installation:

  sp59986 Cyberlink YouCam software V3.5.5.5811

  • Assuming that the Cyberlink installs:

  Another reboot might be nice - Windows love a good restart.

  • See if the device works.

  =================================================================================

  Webcam troubleshooting - Windows 7

  Webcam troubleshooting (Windows 8)

  Good luck!

• BlackBerry Smartphones combine AOL by hand

  Afternoon,

  My AOL is set up to automatically reconcile at certain intervals. I have reduced, and I think it's because the phone constantly trying to reconcile my AOL account. I just opted for my first BlackBerry (storm) to a Motorola Q9. I noticed something similar on the Q9 and could tell him only to reconcile my AOL account on my order.

  I searched through all the menus and have yet to find this as an option on the storm. Anyone know if this is an option and if so, how I would invoke the adjustment to reconcile only when I choose?

  I noticed that a lot of positions for the life of the battery, in my experience, this could be the culprit. After scanning positions (quickly) I didn't see anyone mention specifically.

  Any help would be appreciated.

  Thank you

  Nick

  There is no such option.

  And quite honestly, given that mail messages / 'push' unit, the handset makes very little amount to retrieve mail. However, it is something that you can't disengage.

  You will need to examine other issues battery, like an active browser in the background eater, a request or mapping on break Media Player.

  Here's some good advice from loading, please read and you will see that many of them will be applicable to you.
  http://www.blackberrynews.com/2008/05/20/battery-use-tips-for-your-maximum-battery-life/

• CC 2014 Illustrator EXTREMELY slow race on nine Core Mac Pro 6 with Ram 64Gbs. It's not right :(

  Hello

  I just picked up a new kernel 6 Mac Pro and I'm having some serious lag with Illustrator CC 2014 issues. I'm just trying to select relatively simple objects (an illustration on the side of a coin) and there is a huge delay between when I click on an object and when it is actually selected.

  Someone please tell me they know how to fix it? Please

  My company recently "upgraded" my OS to Windows 8.1. (an operating system prior to Windows 8) and I am now terrible performance when you use Illustrator CC 2014. (2014.1.0 release - 18.1.0 (64 bit)). More problematic is that every 5-10 seconds the screen goes black (not answer) for 3 seconds. I had a similar problem with Illustrator CS a year or two ago - I solved this problem by disabling the automatic update of the linked files. So, I'm suspicious that this problem has also something to do with the Illustrator accesses the server, but in this case I don't know which opens access to the server.

  Another colleague of mine using Windows 8 downgraded from "Illustrator CC 2014" to "Illustrator CC" and no longer has the problem of hic - up (unresponsive). "."

• Battery GS728TS with interfaces and the LAG problems

  Hello

  We have 2 x GS728TS (running firmware 5.3.0.26) switches connected together in a pile with double stacking cables.

  There are 4 servers connected to the battery through the LAG. Each LAG is composed of 4 members and 2 VLANS, 2 on each switch in the stack. Each server running multiple virtual machines.

  Until recently, everything worked fine. However the last week we have suddenly taken in an issue where some (not all) computer virtual on a host could not communicate with VM on other hosts and vice versa.

  After investigation, we discovered that the entries in the ARP on the troublesome VM table did not contain correct entries. Restart the virtual machine has not resolved this. so I restarted the battery and after a long period of time (15 min) the battery came and most of the questions have disappeared, but not entirely.

  So, I checked the table of addresses on the stack of the switch and found that it contains 'bad' entries as well. It shows that some have learned mac addresses are on specific interfaces instead of a lag, and also sometimes these interfaces are not even part of the specified LAG.

  If I turn off one switch and keep it turned off (or the other) then everything starts working correctly again.

  Anyone have any ideas?

  Thank you

  Shaun

  Hello

  During an extended last night maintenance window, I turned off and removed all the power to the two switches in the battery for about 5 minutes.

  I re-applied then power on both switches and after allowing then to start, check and they now seem to be working properly again.

  I just re-checked the switches (about 8 hours later) and they don't always work very well - no notice or detected problems.

  Concerning

  Shaun

• windows 8.1 w 700 battery issue

  After the update 8.1, several questions arose immediately.  Whenever the processor was running any type of task, (opening a program, searching the Web, looking for a file Explorer... etc) the mouse cursor woud lag considerably, to the point where the useless tablet.  I also noticed that when I set up the camera, image lag application terribly when I was moving the tablet.

  This morning, I started to understand what was the cause of this considerable deterioration with the sytem and the lag horrible with 8.1.   It turns out that when the Tablet is connected, no lags degradation system described above is deceased.  The camera works perfectly and it s no lag with the cursor of the mouse what-so-ever.  Yet when I unplug the device return to battery, degradation comes back as soon as I switch to the battery.

  What happens on Earth with the 8.1 and the system when it's on battery power?  8.1. can we really that much a hog processor that the tablet will become useless on battery?

  I had my W700 since January and have not had any problems with windows 8.0.

  It's amazing that a Tablet is unusable when on the battery using 8.1.  any help of acer wih on this issue would be greatly appreciated.

  What you need to do is simply select Performance or balance, because who wouldn't do anything for you. What is the cause of the slow down is the setting of the Mode of low power within these profiles. To resolve the problem of slower, you have to go to change Plan settings > change advanced power settings > Intel platform & thermal dynamic parameters > Low Power Mode and change to allow specific Application or disable.

• A 2 month old iPod Touch 5th generation began to lose its charge the battery overnight.  East - the developer of a battery issue?

  A "renovated" old 2 months iPod Touch 5th generation just recently started losing its charge the battery during the night.  East - the developer of a battery issue?

  Perhaps. Where did you buy this device?

• Battery HP Pavilion 15-N214TX issue

  Hello

  Today, I bought a HP Pavilion N214TX 15 notebook brand new. When I got home, I unboxed it, inserted the battery, plugged into the wall and turn it on powered for the first time. Then, I saw this message:

  HP battery alert
  The system has detected the following battery storage capacity is very low.
  For optimal performance, this battery will need to be replaced.
  Battery (internal) (601)
  ENTER - continue starting
  For more information, please visit: www.hp.com \go\techcenter\startup

  Windows reports, plugged in and not charging.

  I removed and re - insert the battery, entry in the HP Support Assistant application conducted an audit of the battery (only to point out that it cannot find a battery!) and I ran diagnostics pre-boot, who also pointed out that there is no battery inserted. I saw somewhere that you should remove the power supply before running the tests. When I pressed the power button while the laptop was plugged in the AC, the charging light just blinked white three times. I could get at a certain point in the diagnoses of pre-boot on battery, but I always saw the message saying no battery has been found.

  This is a great laptop, it's super fast, software installs quickly, programs open quickly, it stops and starts quickly, but this battery issue is a huge disappointment. I do not expect this kind of problem a new ~ $1100 laptop.

  Help, please!

  -techhead287

  P.S. The battery supplied with the laptop being defective out of the box, can I get a new one for free through warranty? Only, I bought this mobile last night (at the time of writing this post).

  Hello techhead287,

  As the battery is not able to keep a load on your laptop, please contact our technical support at the 1-800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://www.HP.com/cgi-bin/hpsupport/index.pl

  Best regards

• Issue of Pro 6100 satellite about the RTC battery

  I know it's a huge topic which will be discussed on, and my Toshiba is screwed. I even did a lot of research and found it disappointing that my Toshiba may not be repairable, but I have a question;

  When I boot my Toshiba, it looks good, and I can run normal programs (I get the error of bad RTC battery), but for some reason, the Toshiba randomly freezes and I have to stop it after 5 to 20 minutes to use me.

  I tried to leave it on, as some other forum topics proposed to charge the bettery RTC and it went okay, then 20 minutes later, it froze and I had to reboot.

  Sometimes it is not still turn just after that I have forcefully arrested, so I have to wait from hours to days so he can go back on. But it's useless cause it hangs again.

  Any input on it's great and I'll take advice for this problem. I want the RTC battery but it keeps freezing on me, if I want to find a way to prevent this. Thank you!

  PS: ASP Toshiba Theres two locations in my city (Markham, Ontario, Canada), so if all else fails, I'll take the laptop with my father at one of these places.

  Hello

  If you want to reload the RTC battery you don t need boot up the laptop.
  You can simply connect the AC adapter to the laptop and allow it to charge for a piece of 8 to 12 hours.

  The freezing issue for me sounds like an overheating problem. This can happen because of the dust and debris inside the laptop. In such cases, cooling modules may not work correctly.
  In case you I recommend first charging the RTC battery (don t need to turn on the device), then to clean the fans (you can use carefully vacuuming).
  If the laptop freezes then you could try to reinstall the operating system.

  If all of these tips n help so you should ask the ASP for the verification of the laptop.

• The R7000 there Quantenna 5 GHz battery drain issue or has it been fixed?

  Hi, I'm looking to upgrade my WiFi router and I considered the R7000, but do want to not buy a router that drains the battery of my phone when it is connected to the 5 GHz channel and can't see any point in the upgrade if I end up having to stick to the 2.4 GHz I already have.

  I have known the issue recently, when connected to new TalkTalks router (from Huawai) and got tired of waking up to a phone dead every morning.

  I did a little research on Google and found that pilots Quantenna lacked support for negotaition powersaving to 5 GHz if this problem has been fixed. So far, I only found a reference to the R7500 having this problem. If anyone knows if the firmware has been updated to fix the powersaving?

  Thank you

  The R7000 relies entirely on the Broadcom and don't use all Quantenna chips.