Laptop guard crashing and showed a blue screen and restarts... :/

Similar Questions

• Photosmart HP B210a more: HP Photosmart Plus B210a shows a blue screen with error B8145558 and restart.

  For two weeks now my HP Photosmart Plus B210a was wrong to behave. Until that time, I was a happy user, but since it says there is an error in the printer and that I should turn it works again.

  Putting out voltage is actually not possible using the button, as this will trigger a reboot, ending up on the same screen as before. During the start cycle, I have a brief moment where I can access the regular menu before it shows a blue screen with the B8145558 error code. 2 seconds after it is shown, a white screen appears with the title of printer error and the message to reboot.

  So far, I have cleaned the print head and the connections of all dirt and residues. I even managed to start and finish in a copy process, before it gives me the error. However, the error will come, and then it's over.

  Someone has encountered this problem before? Currently, I find only 1 reference to this error in Google and not on this site. Any suggestions that I could try?

  Hi @kootstra,

  From your description, I suspect there is a problem with the firmware that may be irreparable. We can try a reset, but because the printer will not stay on very long main screen until the error appears that we are not able to access the menu of support, we need to reset.

  I'll send you a PM (private Message), but before I do, please see the HP Privacy Statement.

  This privacy statement informs you of our privacy practices and the choices you can make about the way information about you and your online activity is collected and how that information is used. This statement is available on our homepage at the bottom of each web page of HP and HP.com.

  There are a growing number of messages in this forum and elsewhere in the internet with the steps to do a reset on different printers.  Reset to will sometimes fix problems, so resetting is not the issue.

  A few resets require you to enter key combinations to open special menus on your printer that you were supposed to never access.  These special menus are used by developers and staff support for debugging of problems, but they are not intended for inexperienced users and can have unexpected results.  A wrong button push and you might no longer have a printer, but rather an expensive paper weight.  On top of that, if you happen to the 'brick' the printer in this way, it is considered as customer induced damage and voids the warranty automatically. These resets are only intended to be distributed and used as a last resort and under the direct instruction of a representative of the HP technical support. They should not be made lightly!

  Reset the printer: what you need to know

  Please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  

• Windows Vista crashes, I get the 'Blue screen of Death' and I have to restart. Different errors each time it crashes.

  Windows Vista crashes, I get the 'Blue screen of Death' and I have to restart. Different errors each time it crashes. I tried to reinstall vista without success of the problem being fixed

  Hello

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------
  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during "blue screen of death," collisions
  Displays information on all the "crash" of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• PC restarts showing a blue screen and ATI RADEON XPRESS 200 graphics works only with WINDOWS 7

  (1) I have a motherboard integrated ATI RADEON XPRESS 200 SERIES
  I installed the 64-bit windows 7 but everytime I use, it shows a
  BLUE SCREEN and instantly gets restarted.

  ERROR INFORMATION
  
  Problem event name: BlueScreen the system Version: 6.1.7600.2.0.0.256.1
  Locale ID: 16393 BCCode: 1 BCP1: FFFFFFFFC0000005 BCP2: FFFFF960000D69EA BCP3: 0000000000000000 BCP4: 0000000000000000
  OS version: 6_1_7600 Service Pack: 0_0 product: 256_1

  Pls explain why this happens n solution for this?
  
  (2) I downloaded the latest updates for microsoft video card, but they are in the form of files * .cab, can someone explain how to install them.

  With the Xpress 200 integrated graphics, you will not be able to get Aero or other effects of Windows 7.

  You can adapt a motherboard graphics card: AGP or PCI-E slot there. A Radeon 3400 or other card compatible Windows 7 can be pretty cheap and would provide Aero and other effects of Windows 7.

• First Pro CC launch my computer shows a blue screen: kernel security check failure

  Hi all

  Plug-in for some time Adobe Premiere Pro that I like a lot. It works on my laptop Asus on Windows 10. But since yesterday I can't launch it! Every time I run Adobe Premiere Pro my computer stops on saying a screen blue "your computer to encountered a problem and needs restart." We simply collect information etc."is the error: kernel security check failure. So I used the software, which crashed to see because of what program my computer shows a blue screen. After scanning my computer it says that the problem is probably caused by ntkrnlmp.exe and ntfs.sys

  I therefore seek a solution on forums but I've never found! I tried to update my vain pilots en and I also tried to reinstall Adobe Premiere Pro but its didn't work it still shows the same error.

  Thanks in advance for your help

  Kind regards

  Mathys

  Hello

  I just found this on a Forum:

  Good night «»

  After the words... just restore your graphics driver to the previous version, wait that Microsoft developers to create a new kernel update, pour the update your graphics driver.

  As of December 25, 2015

  Friendly. "

  Hopefully this can you help accessory!

• Satellite L505-13W shows error blue screen

  My error on blue screen shows computer laptop SATELLITE L505-13W.
  The operating system is started and after some time, it shows a blue screen error and restarts.

  Even after repair successful when restarting requested repair, he showed the same error.
  So I tried to recover with the recovery cd, but it turned out to be a tragedy.

  He eraced my complete HDD to stone age and smiled saying recovery is not possible.

  Please help me...

  Hello

  If the laptop can not be recovered using the recovery disc, then it feels the hardware problem.
  Are you sure that your recovery disc is OK?
  Have you tried to install the OS using another installation disc?

  Perhaps it would be useful to check if the problem could be related to defective recovery disk, but if the BSOD (blue screen of death) appeared before the installation of the OS, I would say that the problem can be caused by an internal hardware malfunction

  It would be necessary to check the modules of RAM and HARD drive.
  HARD drive can be verified by using the diagnostic software from disk as Drive Fitness Test (freeware)

  RAM could be checked with a tool like memtest, but you need a system to market, then in this case, you can not check the RAM using a software that I recommend to remove a module and test the laptop using a module in each slot

• I bought Adobe Acrobat Pro Extended 9. My laptop got crashed and now I want to install Adobe Acrobat Pro extended 9 as I have the serial number for this product. I'm not able to find the download link for this product, but there is a link to Adobe Acrobat

  I bought Adobe Acrobat Pro Extended 9. My laptop got crashed and now I want to install Adobe Acrobat Pro extended 9 as I have the serial number for this product. I'm not able to find the download link for this product, but there is a link for Adobe Acrobat Professional 9 and I download and run the program installation and entered the serial number and it shows incorrect serial number. I need fix the download link for Adobe Acrobat Pro Extended 9. Thanks in advance.

  Windows:

  Download Acrobat products | 9, 8

  Mac:

  N ° 1)

  Click on the below link, Sign In and open Photoshop Elements download link.

  Do not close the page, just keep it open.

  https://www.Adobe.com/cfusion/TDRC/index.cfm?product=photoshop_elements

  Note: * If we do not keep the page of items in Photoshop, we will have access denied error message when file downloading install direct.

  Then click on the link below and download the installer directly mentioned in step 2.

  Step 2)

  http://trials2.Adobe.com/applications/Acrobat/APRO/9/APRO9_Mac_WEB_WWEFG.dmg

• Photo shows in the library but when I opened to develop that it shows a blue screen with a cross diaginal

  Photo shows in the library but when I opened to develop that it shows a blue screen with a cross diaginal

  Go to preferences > Performance tab and uncheck the option "use graphics processor. Adobe is aware of this problem and are studying, but in the meantime to uncheck this option should your unit develop problems.

• Guard Windows Explorer to crash and restart on Windows 7

  I use a Dell Vostro V13 laptop. Last night suddenly kept windows Explorer crashing and restarting over and over to the point where I can't do anything. I tried the system restore, but the problem is still there. I can't do anything except the exit ramp of the computer with Ctrl + alt + delete. As soon as the restart my laptop the message back and he stops and restarts over and over again.

  I am only able to send this message in SafeMode where the problem occurs.
  I'm not very computer literate, so would be grateful for a detailed step by step help.
  (One of the reasons could be that I tried to update media player VLC, this accident occurred just after that.) I uninstalled VLC but with no avail, explore it crash)

  It is clear the details of the second error problem is the DivXMFSource.dll:

  Fault Module name: DivXMFSource.dll

  Fault Module Version: 1.0.0.72

  Timestamp of Module error: 4cffcf66

  The DivXMFSource.dll is a component of DivX software.

  Uninstall of DivX software should fix the error.

  You are able to do safe mode?

  If not go to the DivX program folder and right-click the DivXMFSource.dll and rename the extension .dll to .old, IE rename DivXMFSource.dll in DivXMFSource.old.

  Restart the computer in Normal Mode and uninstall DivX.

  Here is the location of the DivXMFSource.dll to rename:

  If 64-bit Windows 7:

  C:\Program Files (x 86) \DivX\DivX DivX Media Foundation Components\DivXMFSource.dll

  If 32-bit Windows:

  C:\Program DivX DivX and Media Foundation Components\DivXMFSource.dll

• I try to use develop it but it shows me blue screen

  I try to use develop it but it shows me blue screen

  Lightroom preferences-> Performance tab-> uncheck the option of GPU.

• Hello! I've got CS3 Design Standard - real records and certificate of software license. It was installed on my laptop that crashed and could not be uninstalled. I have now installed on my new MacBook Pro, but can't get it registered with the

  Hello! I've got CS3 Design Standard - real records and certificate of software license. It was installed on my laptop that crashed and could not be uninstalled. I have now installed it on my new MacBook Pro, but can't get it registered with the serial number. Is it because it has not been uninstalled on the previous laptop? What should I do now? THX!

  Maybe this can help someone else...  I had to simply properly uninstall CS3 and reinstall again after that.  I think what he sort!  I also remember having a similar problem with the Mac at work a couple of years back.  Not sure if it is the same for CS5/CS6.  Here is a link on how to properly uninstall CS3 on Windows XP, Windows Vista and Mac OS.  I'm on OS X 10.9.2 but it works beautifully.  Remove from Creative Suite 3 and CS3 products

• Satellite A500 - crashes and restarts when I play games

  Help, please

  For these last months, I had a problem with my laptop crashing and restarting in 10-20 minutes from a game.

  Please help, give me ideas or tell me how to find out what the problem is, I have read a few other discussions to talk about questions of heat but no real answer on how to solve the problem.

  Help, please
  Thank you
  D

  Hi Dale.Johnston,

  Overheating would be a typical pattern of this behavior. I mean, that's if the laptop has a higher internal temperature and it will immediately fit to protect the equipment. Then it the normal behavior of s from overheating.

  Overheating may have different reasons. In most cases it's dust that blocks the fan. This would mean that you have to clean the cooling system of your laptop using the jet of compressed air to blow the dust from the cooling fans.

  Generally, it should help. If this isn't the case, I would check the display driver. What display driver and operating system you are using?
  If you install the display driver Toshiba not they can also cause overheating if it recommendable s using Toshiba pretested drivers only. ;)

• iPad Air keeps crashing and restarting

  Why my iPad Air keep crashing and restarting in Safari? I also think other applications. iOS 9.3.2 must be the culprit because it never happened so often. Any solution?

  Go to settings - Safari - clear the history and data from the Web site.

  If that doesn't work, reset your device. This will not erase your data stored on the phone.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

• My computer crashes and restarts with windows xp but it does not occur with any other OS

  When I use windows XP, 2000, ME, 98 in my computer (Dell latitude D600) it crashes and restarts all of a sudden. But when I installed winodws vista, 7 or ubuntu it will never happen. I thought that the problem could be drivers, so I ran my computer only with windows XP, without installing any driver, but it happens again. I already send my computer to dell and they changed everything in the computer, but I still get the error. What can I do to identify and solve the problem?

  Hello cocodrilo,.

  Thank you for visiting the website of Microsoft Windows Vista Community. The question you have posted is related to Windows XP, 2000, ME, 98 multiboot and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en/categories/

  Thank you

  Jack

  Jack
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Explorer Windows 7 keeps crashing and restarting and it doesn't recognize me as an administrator

  Hello!

  I share the same problems as many users posted, then some a few years ago.

  1 Windows 7 explore keeps crashing and restarting

  a. I've done your first suggestion witch was copy Explorer. exe in system32. Does this rebooted and the problem continued.
  b. began to gain in SafeMode (same problem) and then all the stages of boot minimum troubleshooting to find the root cause of the problem.

  None of those who have worked, and I still have the same problem. So I tried commandprompt and running "sfc/scannow". Then came the following problem:

  2. I need an administrative authorization.  (I'm the owner of the computer and work through an administrative account).  How can I get Windows to recognize me as an administrator?

  Thanks in advance for your help

  Best regards

  Liliana

  None of those who have worked, and I still have the same problem. So I tried commandprompt and running "sfc/scannow". Then came the following problem:

  2. I need an administrative authorization.  (I'm the owner of the computer and work through an administrative account).  How can I get Windows to recognize me as an administrator?

  Hello

  You must run the shell in high mode (Administrator).

  Click on start / all programs / accessories.

  Right-click on the command prompt, and then select the run as Administrator option.

  Run SFC/scannow in the command window.

  Concerning