laser jet pro MFPM177fw color: randomly powers off the power, then press

Similar Questions

• LJ Pro300 color MFP M375nw. Power cycling, displays "49 service error - turn off the power, then press" on-screen.

  Bike constantly, the power display "49 service error - turn off the power, then press ' on-screen before stopping.
  For this printer only when it is connected to the network. Quite happy to sit quietly when printer NOT connected to the network.

  Unplug the network cable from the printer, check and clear all print queues (there may be a doc pdf sitting in a pc or server print queue)

  Once the queues have been dotted, restart the printer and reconnect the network cable.

  If this does not cure the problem, then the likely problem is a defective formatter Board.

  Good luck!

• Laser Jet Pro 100 color M175NW MFP

  Hello

  I just bought Laser Jet Pro 100 but have problems to do the installation despite trying several times.

  Initially, the installation seems to work very well and I was able to print out a few pages until I turned off the printer and turned back on again, the impression doesn't seem to work more.

  Attempts to re - install the printer also failed. The error message indicates that the installation takes too long and asked the facility to perform again.

  I get very frustrated for this printer. What should I do now?

  Thanks for your advice.

  I would try a suggestion more. Could you try to install this printer on another computer. I want to see if the installation fails or not. If so, then I will help you. If not, then there are someone on this Windows 7 computer that blocks this facility to settle. Please post your results.

• LaserJet Pro 200 m251nw: Laser Jet Pro 200 color ink bleed on black and white page after some use

  I print mostly black and white documents. I recently had 2 ink color of defamation in the pages that are supposed to be just in black and white printed. The first was the magenta, and it might discolor the entire page. The second was yellow, and it could fade just the left and right margins. It was two cartridges to Cartridge World, and they have done very well for some time after the installation or always had plenty of ink left when this problem occurred. The manager at Cartridge World has estimated that perhaps the part of the waste of the cartridge has been complete over time and flees to the ink. He said that for most black and white print still causes the drum on the cartridges of color to turn and empty the little ink in waste room. His suggestion was to get a second monochrome printer for most usage of my impression and just this HP product when the color is required. Who is? Other suggestions? If I replace the suspicious cartridges, print returns to normal, at least for a while.

  Hi @la1959,

  Welcome to the HP Forums!

  I see that your HP LaserJet Pro 200 M251nw, color of ink smear on black and white page after some use. I'm happy to help with this problem!

  According to the website of Cartridge World, http://www.cartridgeworld.com, it seems to me that these cartridges are rebuilt (refills). And, the information in this guide, can I refill the ink in my HP ink cartridge? States:

  Yes, you can. But what do you want? QualityLogic, one of the organizations of quality foremost in the world, has tested the performance of HP refurbished vs brand inkjet print cartridges (filled). Results: original HP inkjet cartridges ink far surpassed refills in print quality and reliability of printing.

• Satellite 2435 powers off the power when you try to install the recovery CD of OS

  Happy new year

  Satellite 2435 powers off accidentally when trying to install the operating system from disk with Windows XP Pro startup disk or recovery.

  When starting and working with Winternals AdminPak 5.0, Portable Edition Windows or Dos 6.22 it works stable.
  When booting with the disk recovery he died each time in a different position - when partition formatting, copying the files, etc..

  Hardware problems, isn't? And is it possible to determine and solve the problem at home (because we now hoildays, services does not work)?

  Thank you in advance.

  (Sorry I don't speak English very well)

  When I had my old computer I encountered similar problems in Windows XP and the Windows XP installation. There is a WinXP option to disable the auto-restarting after a problem, instead of restarting, a blue screen stating that the problem appeared. I lived during the installation of WinXP blue screens every time at various times as you and your power off, he appeared on the different WinXP CD (without SP, SP2 with nlite, etc.).

  Maybe your "power off" is hidden blue screen too, but I'm not sure. If this is the case, it may be a hardware problem, so you should test your RAM, your drive hard, etc., for example using memtest for your RAM and the built-in WinXP 'chkdsk '.

  It's probably hardware problems. Were you ever able to correctly use the disk without problem in the past, or is this the first time you try to use the recovery disk?

• Satellite P300 - randomly turns off the power when connected to the external monitor

  Hello

  I have a Satellite P300, Intel Core 2 Duo T9400 2.53 GHz, 4 GB RAM, ATI Mobility Radeon HD 3650 512 MB, running Windows 7 ultimate x 64.

  Recently, I bought an AOC v22 led screen and connect my conputer via HDMI. Everything works fine, but sometimes my computer off just randomly. I might have something to do with my computer overheating, so I clean the fan, but this was not good.

  I think it has something to do with the LED screen because my computer was never off his own.

  Hello

  So this also happens if you n t connect laptop to external display? So, you can determine what is causing this problem.

  If the computer laptop doesn t turn off without external monitor, you should try to update the BIOS and the display driver. Two updates that you can find on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  You close the lid if you have connected the external monitor?
  What operating system do you use?

  In addition, it would be interesting to know how you clean the laptop. That's why I use the jet of compressed air that can blow the dust from the cooling fans and you don't have to disassemble the laptop.

  Good bye

• HP LaserJet Pro 400 color: HP Laser Jet Pro 400 color M451dn

  Just got back from vacation and the language on the digital screen has changed I have know idea what language it is, how do I get it back to English.

  Thank you!

  MontC

  You can try the steps below to change the language to English:
  1. Click Start , click all programs.
  2. look for the HP list, that you highlight of HP, right, will open another menu that displays your printer.
  3. highlight the name of the printer, and that opens another menu with box tool from the HP device. Click the device HP Toolbox.
  4. a page opens. Click the System along the top and which opens a drop-down menu. Click on System Setup. This page of research and in the middle is language and select English. Click apply and close the window.

• Laser Jet Pro 200 Color MFP: cannot scan from 10.8.5 OSX system preferences

  Have recourse to the scanner via the preferences system for 2 years. This was recommended to me at Office Depot when I bought the machine.

  Now I have 'the scannner impossible to complete the scan.

  Copy works by function (from the machine), so scanning / copy glass is OK. Printing from the computer works as well

  (connected by USB).

  Earlier today, before installing the printer v3.1 for OSX driver, I got the message "error com.apple.imagecapturecore 9930.

  I have reset the system twice.

  Am currently with all updates.

  Still does not scan.

  Any thoughts?

  Hi @PhilJ1,

  Please try these steps, it should help, How to open the applications of a developer not identified in OS X Lion mountain.

  Thank you.

• Laser Jet Pro 200 color MFP m2: yet another scan inaccessible victom!

  Like many people here, my HP Lj200 M276 Scan software decided to stop working. I have installed and reinstalled the software, running printing HP Scan doctor, arrested and and started WIA and practically everything else except the reinstallation of the operating system, but I stll get THIS...

  

  When I run the HP print and Scan doctor, I get the following results when you try to fix the scanner...

  

  What the HELL am I supposed to do now? I have already started, stopped and reset the WIA and depedant services without solution.

  Well well, after much experimentation, installation/uninstallation of drivers and to change network configurations, I found the solution.

  Do not use wireless!

  Going back through the history of my network, I realized that the last time that my scanner was working is when I got the printer connected to the router with a cat5b ethernet cable. So I released a port on my router, disabled the function the printer wireless and cable.

  Down and behind, the scanner software works! I can scan with the 10 Windows scanning program and the HP scanning software.

  The only explanation I can come up with, is the different network speeds, that my router supports. The wired devices run at 100Mbit, while wireless devices can be executed at 50Mbit. When I on the printer wirelessly, my computer has been connected to the router.

  When the software is run, he tried to scan, I could hear the scanner run. But to halfway through its operation the error jump upward. When I used another wireless device to scan from the printer, in this case a laptop, it worked without problem. Now that the printer is connected to the router matches the speed of the network from my computer and the printer and everything is good.

  Also, the laptop works also, so this suggests that software was delay due to the faster connection, before the printer to finish as long as the speed of connection of printers is half that of the computer.

  This is just speculation, but with everything that I've tried that sounds plausible. In addition, it's not like Support HP offered no solution, then this is the best I can find. Whatever it is, my scanner and the software works.

  Speaking of the HP support.

  Good on ya' guy to show once AGAIN how USELESS you are!

  Not a suggestion on one of the many posts I have contribited to how solve my problem. WHat than a forum of support if you do not have FICHUS ANSWER YOUR CONTRIBUTORS MESSAGES?!

• HP Laser Jet Pro 200 color MFP m276nw

  How do I change of printer cartridges?

  Here is a link that will help and guide you to replace the toner cartridge.

  http://support.HP.com/us-en/document/c03416779

  Let me know if you get it to work successfully, thank you.

• Laser jet pro 100 color mfp software m175nw will be not install

  In preparing to install the scene until I connected the printer, I get 85% on the blue bar of extraction: ERROR, a problem occurred during the preparation install the software on your system. Restart your computer and run this installer again. If the problem persists, please visit the product support for your product.

  I've been through the suggestions, including the download of the latest version of the software, verify that the printer spooler is running and in automatic mode - nothing works. I ptinting urgent jobs to do and it's frustrating!

  Hello

  I had this problem just today. It took me awhile, but I did the job.

  First, I changed the manual print spooler (in services.msc).

  I then ran msconfig. Went to the services tab and check the box to hide all Microsoft Services and then I disabled ALL of the remaining services, saved and restarted.

  I ran the software as an administrator and it worked.

  I think that the essential is the stage of msconfig, but I did everything I listed above.

  I'll install it and then change everything back to normal.

  Hope this helps

  Douglas

• Satellite Pro A100 PSAAPE: WLan signal off the power switches when you restart

  I have a pro satellite a 100 psaape.
  Whenever I reboot the signal turns off wireless.
  I have to manually enable the wireless switch to get a signal to go online.

  Is this normal or is at - it a way to get this automated so that it is always on.

  Hello

  This is normal since the needs of subssystem wireless initialized manually by the user. But I think it should probably be an option to automate the it.
  I would like to check it out and give some feedback. On the other side, you should look for some options like 'turn on wireless to start windows' and so on...

  Welcome them

• Satellite M30X powers off the power when you touch the USB port

  Hello everyone, just registered and it is the first problem:
  As there is no general hardware forum, I post my problem here.

  I got it twice, my laptop
  (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

  Motherboard:

  NorthBridge: Intel i855GME
  SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
  Motherboard model: Toshiba EAL20

  USB:

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
  Version: 1.0
  Interface: UHCI
  Frequency: 48 MHz

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
  Version: 2.0
  Interface: EHCI

  I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

  Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
  There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

  Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
  I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
  Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

  What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
  Still works well. Now for me, that I broke the USB port Insider somehing.
  I could not determine also the loose parts or unfirm at all.

  Y at - it there, diagnostic software that measures the motto of the port or power problems?
  I have a multimeter, fetch short-circuits with it?

  I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

  Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

  Fabian

  Hello

  I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

  > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

  I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

  However, what we can do is to provide some suggestions and assumptions
  It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

• Saving ink by powering off the power when you are not using it?

  I have a HP Officjet 6700 running under Windows 7 64-bit and read that turning off your printer when you don't use to save on ink. Is this true?

  Hello

  Right, but turn off will save a bit of power. Inkjet printers need ink more when you turn very often.

  I hope this helps.

• E320 unexpectedly powers off the power when change you position!

  Hey guys,.
  Is not my ThinkPad Edge E320 but a few months old, but I've noticed a problem with it. I would like to know if others are facing similar problems and if there is no solution for it.

  The laptop shuts off completely when I move. But I noticed that it doesn't happen if I'm REALLY careful with it and move it into both sides.

  It seems to be a 'soft spot' on the underside of the laptop that forced him to cut immediately when it is pressed. And move the laptop holding down causes exactly that.

  Is anyone else facing such a question? It would be great if someone could help me with this.
  E320 no users, if you have an idea about what is happening and that you may know a solution, please do not hesitate to post on this.

  Thank you everyone.

  I found a solution that seems a permanent solution to this problem.

  Download the two photos FYI
  http://S21.postimg.org/mxsbtwrmv/PHOTO2.jpg
  http://S21.postimg.org/fgnpsfrhj/Photo6.jpg

  I bought the E320 for a year. Never had a problem during my study of honours. That from last week, when moving the laptop, the machine stopped immediately offshore. After some troubleshooting (plug battery and AC power), I noticed that the problem occur only when you press and hold the bottom of the left upper keyboard with pressure.

  Google this question, found a large amount of complaints from the forum of Lenovo and bath tub. Thanks to the entrance of ThunderDuck whirlpool. I just put a thick paper (I chose the photo paper) underneath the SSD (metallic surface caused the short circuit, I guess) and the problem has been corrected.