LaserJet Pro M1536DNF

Similar Questions

• LaserJet Pro M1536dnf troubled fax send... just saying fax work added but does not send

  I have a LaserJet Pro M1536dnf, which is used as a stand alone Fax.  When we try to send a fax, the document is scanned, but instead to send the fax, it says Fax added task.  When you check the status of the fax machine it says nothing is stored and the fax is never sent.  I've updated the firmware to the last and it worked for a bit, but now it don't send faxes again.  He will receive faxes without any problem and can reproduce documents as well.  Is there anything else I can do to try to solve this problem.  I went through all the troubleshooting steps that appeared on the Web site.

  Appreciate the help!

  Hi jloo,

  Please check your private messages and let me know if the steps fixes your problem?

• HP laserjet pro M1536dnf wireless configuration in order to use Air printing

  Since I am trying to print from my new Ipad Air, excuse my newbie questions for networking printing!

  What I know so far:

  1. I understand my printer HP laserjet pro M1536dnf is 'not' a WiFi printer.

  2 by HP support and Apple Support web sites, my printer HP laserjet pro M1536dnf is 'Air Print' active. I guess that a certain update must incorporated the Betacam Air Print!

  3. According to the web site of the HP Support, I have currently the latest firmware installed (20130815).

  Note: On my Config report, it shows the status for IPv4 and IPv6 as "network cable unplugged". I have the address IP Show as active.

  3. my home configuration has the internet cable from my modem cable to my router wireless Linkys E3200 via a coaxial cable. Between my router and my computer is connected through the Ethernet cable. My printer HP Laserjet 1536dnf printer is connected to my computer via a USB cable.

  Issues related to the:

  1. go to after I saw and read about on-line, is correct to say "I'll have to change my Ethernet cable from the router to the computer and change it to leave the router to the Ethernet port on the printer?"

  2. do I have to remove the USB from the printer to the computer?

  3. by removing the USB cable between the printer and the computer, how my computer would communicate to the printer to perform a print job? Unless, I suppose, I add another Ethernet cable between the router and the ethernet port on my computer!

  4 other advice, I might have missed?

  @RicharddR

  Thanks for your post on the forums of hp.com. Here are answers to your specific questions:

  1. you must have all your devices on the same cable modem network: computer, printer, mobile devices. Looks like your Setup is similar to mine. I have mine with the modem installation cable to my Cisco router that broadcast wireless signal. Then I have my devices on this router (computer, printer, mobile devices).

  2. If you use Airprint, you put your printer on a network or wireless. Since your printer is a model of dnf (D - duplex, n = network, f = fax), you must use a network cable and add it to your router. AirPrint is not supported via the USB port.

  3. If you remove the USB cable between the printer and the computer, you need to add your computer to the same network as your added to the printer. You can either do this via the ethernet cable or wireless depending on the capacities of the router and the computer. The important thing is that all the devices are on the same network.

  4. for other tips: make sure everything (computer, printer, router, mobile devices, etc.) are on the same network, otherwise you will not be able to print or have communication problems such as print jobs do not print.

  Good luck.

• Turn down the volume on the tone and ringing for HP Laserjet Pro M1536dnf

  We recently bought a Laserjet Pro M1536dnf.  I went through all the menus as well as the user's guide.  How do you turn down the volume for outbound faxes?  The tone and the call for ringtone is too loud and disturbing for the workers in the room where the fax.

  Hey Candlmc,

  If you press the key on the front panel of the M1536dnf, then you will be presented with the configuration menu.  Highlight the menu of system configuration and select it.  Scroll down the menu for the Volume settings and select it.

  This is the section that will allow you to change the ring volume and the volume of the phone line.

  Hope this helps,

  Jason

• HP LaserJet Pro M1536dnf MFP: Inaccessible Scanner for the HP LaserJet Pro M1536dnf MFP

  Problem:    When I try to scan a document I get the following error: (see screenshot below)

  "Scanner inaccessible.... Scanner communication cannot be established. Make sure that your product is powered, check it out connection and ensure that your network is working properly. If these conditions are correct, restart the product and try to scan the image. If you are running a software firewall, it can block scan communication. Please visit www.hp.com/go/wirelessprinting for help to configure your firewall. »

  

  Shortly before this error message appears the scan on the printer function active (i.e. the scan head heats up and moves on the glass while kindled) , but no preview picture ever, only the error message. This error has just occurred within the last few weeks and before the scanner and printer worked flawlessly, although I'm not sure what happens if something changed to cause the problem. Printing features appear to be affected and functioning properly.

  Background:     
  (1) I use a HP LaserJet Pro M1536dnf multifunction printer (product #: CE538A), fax, scanner, copier.

  (2) my OS is a Windows 7 Home Premium SP1 64 bit.

  (3) I also run Norton 360 first worm 21.7.0.11 and System Mechanic Professional worm 14.5. Disabling the Norton 360 Firewall has no impact and I get the same error "scanner inaccessible."

  (4) the computer and printer are both connected by ethernet cable to my wireless router. My router is a NETGEAR R7500-100NAS. I bought and installed yesterday thinking that my scanning error was due to a bad router. This new wireless router has had no effect on fixing my mistake 'inaccessible scanner. The error is the same today as it was before the new router.

  (5) I ran recently updated HP and no new update is available, all windows updates are installed.

  (6) I tried to uninstall and reistalling the full version of the driver without change, I still get the same error.

  7A) when I run HP Print and Scan Doctor 4.6, most of the time, it shows that all controls the scanner, all green checkmarks, are indicated next to Device Manager, the device status, Windows (WIA) Scan, HP Scanner Twain and HP Scan (see screenshot below)

  

  but then, when I try a test analysis, the "inaccessible Scanner...". Communication of the scanner' error occurs.

  7 (b) other times, when I run HP Print and Scan Doctor 4.6, it shows: (see screenshot below)
  Error of scanning of Windows (WIA): the tool has detected a problem with scanning software (WIA]. Remove the software by clicking 'uninstall '. Reinstall the software with t he product CD or by downloading the software full of the latest features of (recommended) HP customer care.

  

  (8) all other aspects of the printer are working very well to my knowledge (it prints and copies without error).

  (9) I am able to view the IP address of my printer in my Internet browser, but there is no available for me WebScan functionality sweep as a workaround.

  Question:

  What can I do to fix the function scan from my printer that worked flawlessly just a few weeks ago? Any help would be greatly appreciated I'm full of ideas on what is wrong or how to fix it. Thank you!

  -Eric

  Hey @Eric_Bucktown,

  Thank you a lot to get back to me regarding this conflict of scanning. Also, thank you for all of the details that you have included in your messages. It is the first time I've heard talk of Mindspark or other spyware cause conflicts of scan. I'll have to remember to have others perform these steps in the future should similar questions arise. Controls only you need to run is the HP print and the tool of analysis of the doctor. It is designed to fix all possible system software driver and conflicts on the computer. However, as you can see, spyware and malware can sneak between the cracks.

  I brought this question to one of my colleagues who works with computers rather than printers. After I explained to him that you had made to solve this problem, it was suggested to keep your system in good working order and to avoid future conflicts of scan, you run the Malwarebytes Anti-Malware and SUPERAntiSpyware Free Edition once a month. Also, just to let you know, Malwarebytes Anti-Malware and SUPERAntiSpyware Free Edition software does not actively scan your system unless you use the complete edition of Malwarebytes for a cost. This means that the software does not always find the infected files and will only scans your system on a regular basis. If you use your computer frequently, you can perform analysis at the same time a couple of months, and not once a month.

  If you encounter any problems in the future, please don't hesitate to reach out for support on the Forums of HP's Support. It was a pleasure to work with you! Good day.

• HP LaserJet Pro M1536dnf: Re: help cold reset for M1536dnf]

  Hello

  Please send me the instructions to reset cold this printer. I can't access the web interface or the menu of the printer. Thank you.

  Hey @ccalderon,

  Welcome to the HP's Support Forum!

  I understand that you are looking to perform a cold reset on your HP LaserJet Pro M1536dnf multifunction printer the menu on your printer and built-in Web server do not respond. I want to help you with this today.

  I will send you a private Message with instructions on how to reset NVRAM on your Laserjet programming. Please check your private Messages for instructions.

  Good luck!

• LASERJET PRO M1536DNF - problem with send reel

  Hello

  It is a simple (or stupid) question. I just need to send several different faxes with different numbers, but I can just send a fax at the same time. There is no queue, the fax cannot store more than one fax at a time. I think that the fax is not well configured. Can someone help me?

  Thank you.

  Hi WillBTech,

  Update: the printer will do queue while the first fax sent. Here's what I discovered. When the first fax is being sent I typed in the second number, and then press the Send Fax button. The problem, I've noticed, is that you can not see the numbers that you type to the second fax as the screen is showing fax send. Once the first fax has finished the printer will return to the home screen, and then a few moments later will start the second fax that was typed in, while the first was sending. Fall down is that you must make sure that you type the second fax number without any errors. Let me know if you have the same experience?

• LJ Pro M1536dnf MFP: is more duplex

  My LaserJet Pro M1536dnf MFP stopped automatic duplex printing. Once I choose duplex printing and rather fo print on both sides of the paper, the document was printed recto with each page on a sheet of paper. I tested and it will do is more duplex copy either.

  I didn't hear unusual noises or get the error codes.

  Any ideas?  Others have the same problem. Other that this question is a great printer, especially for the price.

  This printer is a replacement guarantee for one who stopped duplexing while in warranty period. The first unit duplex copies always worked.

  Hi John_Mrtz ,

  Thanks for letting me know.

  You can go only with firmware updates. You can rerun the update of the firmware, but probably it will show that it is already updated. I tried the same exact setting, that you used in the laboratory for the Laserjet M1536 and he did the double-faced properly document. It looks like a hardware problem with the device. I am surprised however that the test internal printed duplex test page.

  There is still one thing that we can try reset the printer back to factory settings. I can send you this information in a camera
  Message. In the forum next to your handle name simply click on the envelope to see.

  Thank you.

• LaserJet pro 177: bought used hp color laserjet pro mfp m177

  Installation disk arived broken. How can I do to replace it.

  Just upload what you want the site web theHP.

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

• LaserJet Pro M201dw: Remove the LaserJet Pro M201dw of ePrintCenter

  I bought a printer LaserJet Pro M201dw I have installed the printer. I registered it to ePrintCenter.

  The next day, I had to return the printer for a refund. However, I did not remove the ePrintCenter printer (disable Web Services) before I returned it.

  How can I remove the printer from my ePrintCenter?

  Your help is appreciated.

  Hello

  Please sign in to your connected HP account:

  https://www.hpconnected.com/us/en/#devices/

  Select the one you want to delete, click settings, and then click on delete a printer (right side)

  

  Kind regards.

• Add networked LaserJet Pro 200 to ePrint

  I can't add my new Color LaserJet Pro 200 M251nw networked to ePrint.  When I try to follow the iPad on the orientation of the screen, after entering the printers IP address he wants then connect to Enterprise ePrint.  I don't have it.

  My older inkjet has been on ePrint, no problem.  Help, please.

  Hello
  You try to use the HP ePrint Mobile's application or e-mail ePrint service?
  
  If you try to start with the email ePrint service, take a look to the following document:
  http://h30434.www3.HP.com/T5/user/viewprofilepage/user-ID/2585903
  
  If you try to use the HP ePrint on your iPad app, I would recommend a look at the following document:
  http://support.HP.com/us-en/document/c01616126

• HP Color LaserJet Pro M177 MFP: HP Color LaserJet not able to connect to connected HP

  Hello

  I try to activate my printer (HP Color LaserJet M177fw MFP Pro) ePrint and much more, but I'm not able to do it cause connection problem, I guess.

  When I'm trying to 'print the information sheet', for example, the printer is not able to connect (stay on 'Sign in' loop indefinitely).

  My printer is less than a Vodafone EasyBox router, with firewall disabled and no specific barriers defined by me.

  Should I set some port forwarding (even if they should apply to ignore the firewall, when turned on) or any other specific configuration in the router?

  the same connection problem, of course, it happens when I do touch printer and console web administration, of course.

  In addition, I'll let you know that my router is not blocking access, for example, to-from the web (i.e. I am able to manage my NAS from the outside, since he admitted to a DDNS) and other local devices

  I alreay set 8.8.8.8 and 8.8.4.4 as DNS pri/sec and had an output of cycle after the series of DNS.

  My printer also has a static IP address (defined by the DHCP protocol, based on the MAC address), so not a problem, I think.

  Thanks in advance for your help,

  Lorenzo

  Hi Lorenzo,.

  To enable Web Services fumctionality, you'll need to install the latest firmware on your printer (version 20160525)

  You can locate the current version of your printer by selecting configuration > reports > Page of Configuration, the firmware version is listed under the information section on the printer.

  Updated the firmware on Linux by following these steps, but I don't know if the latest firmware is available for Linux or not, try:

  http://hplipopensource.com/hplip-Web/tech_docs/man_pages/firmware.html

  If the latest firmware is not available for linux, temporarily install the printer on a Windows PC or a my and install the latest firmware:

  http://support.HP.com/us-en/drivers/selfservice/HP-Color-LaserJet-Pro-MFP-M177-series/5303438/model/5303443

  Kind regards

  Shlomi

• MFP HP LaserJet Pro 400 M425dn cold reset

  Hello!

  Help me! How can I make cold reset HP LaserJet Pro 400 MFP M425dn ?

  You can do 'factory reset' menu of the control panel; or permanent initialization of power first, holding and cover the corner area to the right / left of the control panel when you feed on... release your finger when you see «initialization permanent...» ». After you complete and return the loan, it indicates the reset is complete.

• LaserJet Pro 200 m251nw: how to disable these pages printing pesky notification?

  I just bought the LaserJet Pro 200 m251nw to help with homeschooling and coupon printing. A big HUGE machine so far, one small complaint... whenever I have do something or something (ie: plan a printout of the spreadsheet on an app) Springs this page full color printing. I don't want to lose my ink telling me I just do what I know already! Can I disable it somehow? Thanks in advance!

  Hi @g33kyg1rl

  Welcome to the Forums of HP's Support.  I see you want to learn how to turn off notifications in HP connected for your Laserjet M251nw printer.

  Please follow the steps listed below:

  1. Connect to your HP account connected, which will take you to the Welcome screen.
     
     
  2. Please click the drop down arrow next to 'Settings' menu and choose 'Notifications '.
     
     
  3. If please check or clear the parameters of notifications that you prefer and then click on "save changes".
     
     

  Please let me know how it turns out.

• Color Laserjet PRO MFPF 377dw: problem with Color Laserjet PRO MFPF 377dw and HP network scanner

  After removing the package of printer drivers HP, all attempts of resettlement via WLAN regularly fail before the end, which indicates that the device is not found. I physically connect the printer to the computer by USB cable to install the software successfully. When I go to WLAN Wireless thereafter, the printer works perfectly within the network. If I remove the USB cable, the following error message appears when I try to start scanning HP: HP CLJM377 Scan found . In other words, HP Scan cannot be used with a PC not connected by USB cable. All other remote features function normally printer in wireless, including HP Scan & Capture. Is there a possibility to correct this, via the Windows registry from my PC?

  MrRobot wrote:
  

  Hello! @Chirsistei, your description of the HP product is classified as a commercial product (business). Our sales support team provides support via the channel of entry here. If you need immediate assistance, you will need to open a session one business with our sales support team. Click on this link http://ow.ly/I3gw30140F8 for more details.
  Let me know if you want more information and/or assistance.

  Have a great day!

  See you soon!

  Hello Chetan,

  I think I'm in the wrong forum here because I live in Switzerland and here the Laserjet Pro M377dw color is sold to private users. I have no access to a support plan and use the printer in my home office network. Your proposed solution therefore does not help me, during this time, I have posted this problem in the forum on language German you need not to pursue this new. Thanks anyway