Library of TV on HPE-475uk detection

Similar Questions

• HPE-475UK failure hard drive - need to replace

  For a HPE-475UK, can I replace the internal WD1001FAES 7200 rpm 1 TB Caviar Black HD with a 1 to Caviar Green 5400 RPM? Whatever it is will have to change the motherboard if you use the lower speed device?

  Thank you very much

  GTC357

  Hello

  No, you won't have to make any configuration changes.

  Best regards

  DP - K

• HPE-475UK & USB3.0

  I'm looking for advise on the viability of the USB3.0 added to my desktop PC.

  It's a HPE-475UK - two years.

  It seems to be an obvious step due to the benefits of speed and future accessories.

  However I seem to be unable to find information that supports (or not) as appropriate.

  If USB3.0 can be incorporated in some form - probably a card in a free slot? -Can it work with the existing USB2.0 slots that are spread all around the case

  Hello

  Your PC came with VISTA originally.  I suggest you upgrade the operating system to Windows 7 or Windows 8.

  This PCI-E version 2 x 1 USB3 cardmight work.

  Why Windows 7 or Windows 8?  Windows 7 and Windows 8 improved xchi support.

  The Intel H57 chipset has a maximum level of 14 USB2 ports.

  There is no guarantee that any card PCI-E data will work on your PC and/or interrupt.

• Replacing hard drive and a RAM and more HPE 475uk

  Hello

  I was wondering if you could give me some advice at all?

  My hard drive of 4 years HPE-475uk PC deskt starts to become noisy and slow and had errors. Rebooting/resetting the computer and reinstall Windows 7 did not help so I think it's time to present a new. While I'm here, I would like to replace my RAM too.

  My computer is a HPE-475uk, Intel i5 Dual Core, Windows 7 64 bit and I have 8 GB or Ram (2x2x2x2). Here is a link to the complete specification / card mother etc. If this can help, or I do not have any sense! http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c02622053&DocLang=en&docLocale=en_US&...

  Prevented, I'm not that technical and I was out of the loop for so long that I'm not sure what is now compatible with my PC and I was wondering if someone could point me in the right direction to correct products!

  I would like to replace my current drive HARD SATA 2 1 TB 7200 RPM with the same size (or larger and faster if it is compatible?) but with a large cache. (I am a musician and use a lot of sampled instruments). Can I put a disc of 2 TB SATA 3 right? If I do anything other that install it because it's a more recent material on an old motherboard? (IONA-GL8E)

  Also I would get out of my yard MB of RAM PC3-10600 DDR3-1333 (240 pin) and replace it with 16 GB max that my motherboard (4x4x4x4), but not sure what memory is good for my computer. Whenever I go to buy, anyone says it is not compatible or too fast! I'm looking Technology Kingston 4 GB KVR13N9S8/4 1333 MHz DDR3 Non - ECC DIMM Memory Module. Can you tell me if it's ok or point me to one that will not work if?

  Thanks a lot for your help! It's much appreciated!

  Kat

  Yes. These modules that you linked to on Amazon should work.

  With a single hard drive, you can reduce the C: \ partition and create a separate partition for your work.

• HPE-475UK: 10 Windows Installer Clean

  As thousands - or should I say millions - I was informed that my PC is eligible for the microsoft Windows 10 update.

  App W10 conducted its analysis and reports there is no conflict other than Windows Media Center that would be uninstalled.

  I am pessimistic and believe all this seamless up to this day, etc. - so I think I will sit this awhile--after all, I've got 12 months.

  Assuming I want to move forward to a point I have a few questions haunt me.

  1.

  The Hauppauge TV tuner will probably not work. Otherwise, it should be a pretty seamless upgrade of Windows 7.

  I did it on an old socket 775 PC with an Intel Cor 2 E8400 processor and it was smooth sailing.

  I would add that the old system of target was gaming grade (mobo ASUS CRosshair IV Rampage) with a 120 GB SSD installed as a startup disk. Upgrade your system to a SSD boot is a thing, you might want to.

• HPE-475uk: upgrading memory

  Recently, I have tried video work - strictly business - and for the first time that I saw my PC put to the challenge by the task, I have put.

  He installed a 6 GB memory rated bank - I guess, but I'm sure that without dive inside it will be 3 x 2 GB, 3 of the 4 slots available for occupation.

  While I am convinced that an update will be interesting, this raises the question how well to do and what are the criteria.

  Thi is a unique exercise and instinct told me to go to the maximum capacity (16GB)

  However I have read somewhere on the web that despite the capacity 16 GB - installation of more than 8 GB is a waste of time - (I think stupid, it was that the term employee who seems a bit shocking but no matter).

  Can anyone offer an opinion?

  Another dilemma - seeking options that I find there are multiples of 4 GB and 8 GB - so using 4 or 2 slots.

  Module 8 GB is viable individually or in tandem? As a pair should they be put in correspondence?

  If I opt for the 4GB modules can they be added individually or must they be purchased as matched pairs (or quartet.)

  A technique more point specifications of memory. confused me as they quote DIMM3 - 1066 & 1333 for the same Dimm module.

  I think that my existing modules (3 x 2 GB) are 1033 MHz according to the documentation, but excludes in 1066?

  If anyone can provide advice will be much appreciated

  Hello

  Below images should clue you and more information because do me not openly.

  

  

  Your first consideration should be Support HP or HP sales during the consideration of upgrades or replacement of memory. If you want to consider other manufacturers of the best way to avoid memory problems is to contact one of the leading manufacturers of memory. I would recommend that you try the tools of these manufacturers: Corsair, Kingston and Crucial. Once you have determined the DIMMs that you need, then contact commercial or technical support to check that you have selected the correct DIMMS. If you buy directly from manufacturers, then they will stand behind their products.

• HP Pavilion Elite HPE-475uk: upgrade my CPU to an Intel Core i7 processor

  Hey guys I really appreaciate your help. I want to improve my cpu to an Intel Core i7 processor. I currently have a processor Intel Core i5-650 3.20 GHz one. Can you please tell me exactly what i7 processor, I need to get and where can I buy it from? The motherboard I have is a MS-7613(Iona-GL8E).

  Thanks a lot for your help

• HPE-475uk. Windows 7. Cannot download updates - coming has failed every time.

  

  Hello:

  Please see if this link is useful for you.

  http://support.Microsoft.com/mats/windows_update/

  Paul

• Opening hangs opening of library

  Hardware environment:

  -Macbook Pro mid-2012 w/240 GB OWC SSD

  -Display the thunderbolts 27 "

  -Case of Thunderbolt external OWC with a 3 TB Western Digital hard drive and a 1.5 TB WD hard drive.

  -Macbook and OWC box both connected to Thunderbolt display

  Software environment:

  -OS X El Capitan 11.2.4 beta (15E27e)

  -Opening 3.6

  -190 GB managed Aperture library consisting of about 37 000 photos stored on the 3 TB drive

  -Small library managed on the Macbook SSD (used on the road)

  Description of the problem:

  A week ago, opening crashed while I was doing a lot of routine tasks (import, editing, cataloging). It crashed several times during each attempt to re - open until I got the warning repeated accidents indicate a problem (really?) and I need to repair the database. I did it; still crashed. I have repaired permissions. still crashed. I have rebuilt the database; still crashed. As a last resort, I created a new library and tried to perform a restore of the vault that I kept religiously updated on the 1.5 TB external harddrive, but the locked restore operation the machine about 2/3 of the way through, then, hands-free, the Macbook restarted. I have opened the new file that Aperture was trying to create during the restore operation. There was a lot of pictures that have made to the course. and many who have not.

  At this point, I thought it would be a good idea to "relocate" these photographs who survived the restoration, i.e. convert them of 'successful' to 'referenced', so that if I could never open to run again I should at least have something left. Opening crashed halfway through the relocation process. I downloaded a trial version of Capture One Pro 9 and tried to import the Aperture library, but it crashed after about 8000 pictures. In short, I don't any of my 37 000 photos in Aperture!

  Here's the really interesting part: if I run the opening using my MUCH smaller library on the internal SSD flash of the MacBook drive, it works very well and is stable. Opening worked very well with this library under this beta version of El Capitan for awhile before the question is asked. If I import all of your photo library, they all come, but I lose several books I have built or being designed and I lose my catalog structure.

  Well, it seems that there is some sort of corruption in the largest library integrated repair tools does not detect or cannot fix. Can anyone think of a way to solve this problem outside again in the Photos app?

  -OS X El Capitan 11.2.4 beta (15E27e)

  Are you El Capitan 10.11.2 Beta or Beta 10.11.4?  Your version number is somewhere between the two?

  If you run the 10.11.2 beta version of El Capitan, consider upgrading to the stable version current and most recent Mac OS x 10.11.3. Make stable version was released a few days ago.

  A week ago, opening crashed while I was doing a lot of routine tasks (import, editing, cataloging).

  What happened directly before the accidents began?  You have imported new photos?

  If you have imported some corrupt media, Aperture may crash trying to make previews. To check, try to launch the opening while holding the SHIFT key at startup. He'll get over the generation of previews.  If you can get access to the photo library of Aperture in this way, try to export and delete the photos you last import. If one of these photos is should be the source of the problems, you may be able to repair your Aperture library after you deleted these photos.

• HPE-475 wireless card detects only networks

  For these last months, occasionally, my computer would start but be unable to detect wireless networks. It seems that l ' simply down to an hour or two by magic would solve it. Research at the time indicated that he was unable to find a driver for some reason any.

  However, today, several hours of the computer being off has not solved the problem, and the Device Manager indicates that the card works fine, without worries of pilot. Maybe, I'm looking at the wrong thing.

  I was able to connect using an old wireless dongle, but I don't want that it is the permanent solution.

  What can I do to better diagnose and solve the problem? I searched a bit, but couldn't find anything that seemed specific to this situation.

  Product name: HPE-475

  Product number: BU082AA #ABG

  Operating system: Windows 7 Home Premium Service Pack 1

  Error messages: No.

  Recent changes: No.

  Performed troubleshooting: attempted to "Diagnose" through network connections. He suggested to check the router. The router is fine, several other devices are able to connect. Diagnosis then says it cannot solve the problem of connectivity.

  Thanks in advance!

  -Phil.

  Hello

  If the WIFI worked very well using the current router then mixed mode setting is not the problem.

  If Device Manager shows no errors and you cannot connect wirelessly then the WIFI card is most likely the problem.

  Good to hear you have an extended warranty.

  ContactHP support.

  Jaco

• Library meets live TV with the error: "there are currently no TV signal detected for this channel. The channel may be temporarily off the air. »

  I recently changed my TV card to an analogue of Hauppauge PVR150 at a Hauppauge DVB - S Nova S more. Media Center has worked well before.

  Media Library will recognize the new card, search and branch on 239 satellite channels, but may not display the channels giving the error message "there is currently no TV signal detected for this channel. The channel may be temporarily off the air. »

  I have installed WinTV 7 and that you can view all the channels very well in this program so obviously the map and the intensity of the signal are not the problem.

  In my quest through other forums, I heard problems re codec: mpeg2 and we tried several packs of codecs (including shark007) but with no improvement.

  My last move was to uninstall Media Center, uninstall all codec packs, uninstall the TV card and drivers, then reinstall the media library and the TV card and am still unable to view TV channels.

  Suggestions have greatly accepted.

  I've searched the Internet high and low for a solution to this problem and can lead to nothing more than what is proposed here by Divya.

  The problem seems to be fairly common and seems to be associated with codec. Most of the solutions I've come across related to the installation of media center alternatives and after several tries I finally opted for new version of Media Portal 1.1.0 beta

  Installed without a hitch and so far the interface is similar to the media library but has better customization and the ability to incorporate plug-ins.

  I did try the latest version (1.0.2) of the media portal, but said she had a few problems of stability (probably related to the W7 compatibility).

  Very happy now with Media Portal 1.1.0 Beta so will not need any other solution to this problem.

• Windows 10 - ADE not detected when I download books from the public library

  Since installing Windows 10 and 4.5 of the ADE, when I download a book in a public library it just downloads the file to some directory .epub I chose.  To get it in ADE, I have to go through the "Add to library" function in the ADE.

  That's fine, but ADE does not recognize it as a borrowed book, so I can't return it when I finished it.  I approach the maximum number of books I have checked with my local library because these books will not be returned.  Apparently, I have to wait for them has expired.

  Ideas?

  Well, I got the answer today at our local library.

  Books, that I was just downloading was be books "Open EPUB", which means they have no DRM protection.  I can keep them as long as I want.

  An unexpected consequence of these 'loans' is that there is no way to return the books before their expiration date, so that they are based on my library account, running the number of books I checked.  The librarian told me that if I really need to send back them at the beginning so I can consult books more I could send a request it and it can return manually.

  Problem solved.

• can not detect the iphone after upgrading 12.5.1.21

  Set to update to the latest version of itunes (12.5.1.21) and now itunes does not detect my iphone.  tried to remove the lockdown folder. tried to restart all devices.

  Windows 10 with all updates installed. Someone at - it suggestions?

  If your iOS device does not appear in iTunes, try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  To step 3 above, open the Device Manager. Expand one of the articles that are listed.

  • USB Bus controllers
  • Imaging devices
  • Portable devices
  • Other devices

  Plug in the appliance. You should hear the telltale Windows sound device connection and a Division must acquire a new entry. This should be your device. It cannot be labelled properly at this point. If you do not hear a suspicious noise cable damaged.

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support Apple version of the above opinion.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates. 64-bit users might also try the alternate build Download iTunes for Windows (64-bit-for older video cards) , which is sometimes a useful workaround.

  Or try to go back to the last version of iTunes that has worked for you. See the programs installation of iTunes to download links. If you're back 12.5.1.21 to 12.4.3.1 or 12.4.2.4, for example, then you will also need to restore the database of the library using the method described in the empty/corrupted after upgrade/crash iTunes library. The tip makes suggestions to reintroduce recent purchases, so at worst, you lose a few meters or a newly created playlist.

  TT2

• My imac (El Capitan 10.11.6 - 2 Terabyts) complete and FCPX disk will not work. I moved a few fcpxbundles library to an external hard drive (seagate 2 trabyte) and erased from the iMac. NowFCPX said that missing data as effects therefore can not shar

  Help!  My FCPX (v - 10.2.3) does not work because my iMac drive is full (iMac 21.5 inch has 2 terabyte w / v OS El Capitan 10.11.6) I had tried to free up space by moving tons of files on a usb disk Seagate (2 terabyte) speedboat that barely made a dent. then on the advice of a friend I found (in movies) a file called Final Cut backups. There were 4 files with extension, ".fcpbundle" I have three of them moved to another drive to Seagate usb - they had 2.82 GB, 21.6 GB and GB 68,21 that I thought should be enough and them removed from my iMac drive - bad! It says I have only 13.46 GB free on my 2 terabyte iMac total!

  The fourth fcpbundle it's TB 1.72! But before leaving that I returned and opened FCPX and found the warning triangle around my library... While my last project looked OK I couldn't / the share of exports because the pop-up says FCPX has no data for efx etc (the media looked at and display fine) and cannot be taken out.

  FCPX can work with the "beams" moved to another drive? How the detectable in a new place? Or how to put them back?
  How can I make sure that future packages clutter my iMac again?

  Do I need a RAID disks? If yes which?

  I found other folders in folders 'Make files' and records backup for projects with the .fcpbundle inside files

  How can I get this sucker working again?... and what should I do to keep him from doing the same thing in the future?

  Thank you

  John

  :.. then on the advice of a friend I found a file called Final Cut backups (in movies). There were 4 files with extension, ".fcpbundle" I have three of them moved to another drive to Seagate usb - they had 2.82 GB, 21.6 GB and GB 68,21:

  The backup files are only the database files (no media) and must be low, not gigabytes, do not know what is happening there.

  Media libraries stored in the bundle of FCP X library or stored outside?

  If stored at the breast, called managed media, simply copy and paste the library to a different location.

  Make sure that library books newly located correctly before you remove what either.

  Perhaps check your settings of the library.

  Click the library icon in the browser and it appears in the Inspector:

  

  By clicking on change settings shows this:

  

  Move the mouse over the media and it will reveal the path where things are sent.

  Then you might be able to track down what goes where.

  From you description, it seems that most of the media files and rendered is not be moved successfully.

  Some screenshots would be useful if you can't find where stuff is.

  Al

• Photo library - iCloud how to remove duplicates

  All, someone knows something about OSX/IOS 'Photos' app will detect and remove duplicates photo9?  My library 'Photos' 63 299 photos & videos of 2135 from may 2016 and at least 10,000 + of these photos are duplicates (based on an analysis of Photosweeper). I have checked the results of the analysis of Photosweeper by doing a manual visual comparison and check images original in iphoto library (using the function location of show) and confirmed that these 10 000 + photos are images duplicate identical with names of different files in different parts of the photo library database.

  So what is happening and how to stop 10-15% of my picture library being duplicate files! I will raise this directly with the apple support payment for the 1 TB icloud service to cover my very large library 'Photos', which should probably be just a large Photo library!

  A few other comments for those who have a double problem:

  -L' old iPhoto application used to "detect duplicates" when import but the new application 'Photos' does not. Anyone know about this?

  -J' saw the documentation from apple saying the icloud search duplicates in 'Photos' when in the icloud, but clearly not work or it does not work if duplicates exist also in the version of the imac to the library 'Photos '.

  -Beware of apps that claim to find 'photos' duplicate and are recommended on various Internet sites, a number of them don't work with the old iphotos app the new application 'Photos' (I discovered after you pay and download). If you need a remover of duplicates of photos that work with 'Photos' review and stay away from any application that do not specify clearly and explicitly he works with "photos" and has been seen since the release of the Photos app.

  + I paid $10 for "Gemini" dual Finder and has been a complete waste of time that didn't work only not with the "Photos" application (it wasn't not clear documentation or support, and when I trigger it supported by Macpaw that they said gemini does not support photos and told me to buy another app macpaw - I told them to go jump in a Lake).

  + I found very good Photosweeper that you can set to match exact or variable (for example photos of accidental burst which are 99.99% identical but 0,1s collapse) and then you can right click to view original file / image in the library to manually check duplicate (if you are paranoid like me) - there are many other paid apps that also make this store then around

  Photos detects duplicates when you import pictures and when you synchronize with ICPL

  Photos does not analyse the duplicates, but checks for them during import and download of IPCL

  There are a few duplicate programs that are tested as safe with Photos, including PowerPhotos, PhotoSweeper for the pictures and Duplicate Annihilator for Photos - do not use a tested and documented as safe\

  And I'm not clear what your post is about since you are asking how to find duplicates and then provide a good answer - photoSweeper - it is one of the safe and effective ways to remove duplicates for Photos

  LN