Listener RTF editor Client problem

Similar Questions

• VPN Client problem

  A remote user on our network has problems with the Cisco VPN. They are using Win XP, Cisco Client 3.5.2 and connect via a router of Compaq Ipaq into a modem cable. When they VPN in our 3000 VPN concentrator works very well. When they try to VPN in the PIX on our network, it indicates that the client is no longer. If they use a Microsoft VPN to connect to the network with the 3000 (we run both MS and Cisco VPN) with it set to use the remote control, the default gateway, the Cisco VPN will connect to the PIX, see the network behind PIX, ping stuff behind the PIX, but not map a drive. The remote user can ping the PIX of their unVPNed in the remote location. No other user is a problem connecting to the PIX (except those with the bad remote access or broadband satellite which cannot VPN into anything anyway). We have even a few AOLer connect to it. Help me please.

  If the compaq ipaq router makes a PAT, that might be the problem. PIX is unable to manage the ipsec clients who crossed pat. The vpn3000 has some mechanism to deal with this. PPTP is different to ipsec.

  You must ensure that the ipsec client has its own public routable ip address.

  Kind regards

• Windows 7 64 bit VPN client problems

  Hello

  I am running Windows 7 Professional 64 bit and Cisco VPN client 5.0.07.0240. I am able to connect to my corporate network and work ok but connection is very slow!

  Connection time is distributed as follows:

  Client program VPN Opening: 70 seconds.

  Click on connect and wait for the user credentials dialog box: 30 seconds.

  Enter the credentials, and then click ok then 'user authentication': 90 seconds.

  "Negotiate security policies": 60 seconds.

  User area credentials if poster again, re - enter the credentials that the dialog box is empty, and then click ok: 90 seconds.

  "User authentication", then connection established: 120 seconds.

  I have a colleague running 64-bit Windows 7 (ultimate edition) which uses the same version and does not have these problems.

  Any ideas anyone?

  See you soon,.

  Gary

  Gary, thanks for the update. If disabling the firewall and restart vpn service did not help. Could you please try and install the 5.0.07.0290 version?

  Before do you, I would like to know if you import .pcf for the VPN Client files. If so, please try to re-create a file .pcf on the PC and try and use this file to connect. Also, I see that the existing .pcf file you are using is a file read-only. Could you change this and give permissions to write to the file, and try to connect. If th does not help the two steps will then install the 5.0.07.0290 version.

  Thank you

  Delvallée

• VPN client problem long transfer of files with VPN3000

  I have problems transferring big files (more than 4 MB) using customer vpn 4.8.02 or 5.0 with vpn3020 4.7.2.N

  It happens the question with MTU. Try reducing the MTU value by running the file setMTU.exe on the VPN client. Make sure you do not fragment bit is not set on the intermediate routers. For setting MTU on VPN 3000 refer URL http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_guide_book09186a00800d81b3.html

• VPN access with VPN client problem. Help, please

  I have a PIX 520 as VPN tunnels endpoint device. I was able to establish an IPsec connection. I checked that I have gave me an address in the IP pool that I set up but I can't to any resource on the internal network. I could only ping myself. When I run ' ipconfig/all' I see my address on the correct vpn with DNS interface, but my front door is set to my own address. I think that's the problem. Please help me solve this problem. Let me know if you need more information.

  Here are some suggestions you might try to get this working:

  1.) change your "taken" to access-list. The lines are no longer supported by Cisco even if they still work. This will help you in debugging your access list because there will be some hitcounts.

  There is a tool from cisco for conduits of concert on access lists:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX?sort=release

  Download the: occ - 121.zip

  PIX Firewall Outbound leads binary converter for Windows, version 1.2.1

  2.) change your pool of VPN.

  IP local pool techvpn 10.x.x.100 - 10.x.x.120

  With this, it's already you have a 10.x.x.x subnet in your internal network. The ip pool automatically assigns a 255.0.0.0 for the VPN Clients subnet mask. This may cause routing problems. You can use a subnet used anywhere 172.16.100.x.

  example:

  No vpngroup address techvpn pool lsdvpn

  no ip local pool techvpn

  IP local pool techvpn 172.16.100.1 - 172.16.100.254

  vpngroup address techvpn pool lsdvpn

  No inside_outbound_nat0_acl access list

  No outside_cryptomap_dyn_20 access list

  inside_outbound_nat0_acl ip access list allow any 172.16.100.0 255.255.255.0

  outside_cryptomap_dyn_20 ip access list allow any 172.16.100.0 255.255.255.0

  Claire ipsec his

  Claire isakmp his

  sincerely

  Patrick

• Impossible to listen to the music - problem with sound card

  original title: sound card

  I went to listen to music and he says there is a problem with my sound card, need help please!

  Try going to the site of the manufacturer of your computer, look for the support page for your machine and then download and install the audio drivers for W7.

  Failure to comply with this re-post giving the exact message.

  See you soon,.
  Jerry

• BSOD with VPN Client problem

  I use the VPN Client 5.0.06.0110 to connect to my computer at home at my desk, which has an ASA5505.  If my immediate network to the client PC connection is lost while the VPN is active, I get a BSOD.  There is no problem if my grave DSL or a cable beyond my router is disconnected.  He only (and always) will fail if the network cable to the computer running the VPN Client is cut (or if my router loses power), while the link is connected.

  I am running:

  Windows 7 (all updates installed)

  Pentium Core 2

  4 GB of ram

  Atheros L1 Gigabit 10/100/1000 controller

  Any suggestion would be appreciated.

  BTW, here is the description for your reference:

  PC restarts if physical link is disrupted when a VPN connection

  Symptom: Restart the computer (the user can also see a Blue Screen Of Death (BSOD) before the reboot, based on the setup of the PC) if the physical link is disrupted when a VPN connection (that is when you see the error message "a network cable is unplugged).  This can occur if you run "shutdown" on your PC is connected to the way of the switch, turn off the SOHO router (or switch) the PC is connected to, lose your WiFi connection, or even disconnect the LAN cable to your wired Ethernet port. Conditions: Loss of physical connection during a VPN connection.

• vCenter - vSphere Web Client problem

  Hello

  We have some problems with our Web Client vSphere. The vCenter 5.1 is installed on a Windows Server 2012, and you can connect to the Web Client.

  When you log on as "Administrator" (the Windows account) everything works fine, but when you use the admin@System-Domain account you can connect, but there is no display resources:

  No ESXi hosts, no VMs, no data warehouses, nothing.

  CU

  Well you would login to VC using the account administrator (via the web client), click on the Victoria Cross and select the permissions tab, and then add the admin@system-domain and assign the required permissions.

  Girish

• Skin Editor, button problem

  In a project that I have, there is a problem, if I go to skin editor and try to change the playback bar most of the buttons is not possible to activate. Why?

  In my other project, its possible to check which buttons I want in my PlayBar.

  Hello

  Can you please check if you have no pre-test questionnaire slides in your project?

  If yes then, by default, it allows branch Option that supports, and in this case the PlayBar buttons are disabled. If you want to appear the PlayBar buttons, you must remove Slides from questionnaire pre-test or uncheck the branch supported by going to Edit > Preferences > Quiz > settings.

  
  

  Kind regards

  Ajit

• Tecra 8200: Wifi and LAN Manager client problem Win2k Pro

  Hello

  I just install win 2000 pro on an old Tecra 8200.

  The "LAN client manager" says that I'm connected to the wireless access point but windows icon indicate that the wire is cut.
  Is there anyone know how to fix this?

  Thank you.

  PS: I get the latest software and driver on Toshiba website and the wifi switch power switch is turned on.

  Wait a minute: you can use WLAN or not? You are just irritated because of this icon of windows or what?

• % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection refused because of the failure of the path opposite. NAT VPN clients problems after that put 8.3.2 to level.

  I've recently updated to 8.3.2 and I have been informed of these NAT changes, but even after reading the https://supportforums.cisco.com/docs/DOC-12569 I am still unable to rectify the communication network 192.168.100.0 VPN with hosts on 172.16.1.0 and 172.16.9.0. VPN clients connect to the external interface, and I try to ping inside and the demilitarized zone, respectable 172.16.1.0 and 172.16.9.0 hosts. VPN client shows that the two previously mentioned networks such as roads of security, but still not to the ping pong.

  # sh nat

  Manual NAT policies (Section 1)

  1 (inside) to the (whole) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  2 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  3 (inside) to the (whole) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - obj - unidirectional 192.168.100.0 192.168.100.0

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 172.16.12.0 obj - one-way 172.16.12.0

  translate_hits = 0, untranslate_hits = 0

  Auto NAT policies (Section 2)

  1 (dmz), to the source (external) static obj - 172.16.9.5 interface tcp www www service

  translate_hits = 0, untranslate_hits = 142

  2 (dmz) (outdoor) source static obj - 172.16.9.5 - 01 interface service tcp 3389 3389

  translate_hits = 0, untranslate_hits = 2

  3 (dmz) (outdoor) source static obj - 172.16.9.5 - 02 interface tcp ldap ldap service

  translate_hits = 0, untranslate_hits = 0

  4 (dmz) (outdoor) source static obj interface - 172.16.9.5 - 03 service ftp ftp tcp

  translate_hits = 0, untranslate_hits = 0

  5 (dmz) to (outside) of the source static obj - 172.16.9.5 - 04 interface tcp smtp smtp service

  translate_hits = 0, untranslate_hits = 267

  6 (inside) source static obj - 172.16.9.0 172.16.9.0 (dmz)

  translate_hits = 4070, untranslate_hits = 224

  7 (inside) to (dmz) source static obj - 10.1.0.0 10.1.0.0

  translate_hits = 0, untranslate_hits = 0

  8 (inside) to (dmz) source static obj - 172.16.0.0 172.16.0.0

  translate_hits = 152, untranslate_hits = 4082

  9 (dmz) to dynamic interface of the obj - 172.16.9.0 - 01 source (outdoor)

  translate_hits = 69, untranslate_hits = 0

  10 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 196, untranslate_hits = 32

  I think you must following two NAT config

  NAT (inside, outside) source static obj - 172.16.1.0 obj - 172.16.1.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
  NAT (dmz, external) source static obj - 172.16.9.0 obj - 172.16.9.0 destination static obj - 192.168.100.0 obj - 192.168.100.0

  Please configure them and remove any additional NAT configuration and then try again.

• Cisco 2621 to VPN client problem

  If I ping on the client to the network (behind the router), debug displays the client encryption and decryption of the router. The ping will not, because the router is not encrypt and so the customer is not getting anything to decrypt.

  The Setup is a bit different because the default route is within the network, as it is not the regular internet gateway. I have to add routes for pointing the customer who logs on the internet. Also, one machine uses this as a gateway (using a routemap). To troubleshoot, I removed the routemap custom without result. I think to change the default route, but I don't see how this would have on it.

  Any ideas? Am I missing something?

  Cisco 2621 12.2 (15) T running to the latest version of the client.

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  username password XXX 7 XXXXXX

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  AAA - the id of the joint session

  IP subnet zero

  !

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  Configuration group customer crypto isakmp XXXX

  key XXXXX

  pool ippool

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  !

  interface Loopback1

  192.168.254.1 IP address 255.255.255.0

  !

  interface FastEthernet0/0

  IP address 200.x.x.x 255.255.x.x

  no ip proxy-arp

  NAT outside IP

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface FastEthernet0/1

  the IP 10.0.0.1 255.255.255.0

  no ip proxy-arp

  IP nat inside

  route CUSTOMGATE card intellectual property policy

  automatic duplex

  automatic speed

  !

  IP local pool ippool 10.172.10.100 10.172.10.200

  IP nat inside source map route sheep interface FastEthernet0/0 overload

  no ip address of the http server

  no ip http secure server

  IP classless

  IP route 0.0.0.0 0.0.0.0 10.0.0.30

  IP route 20.x.x.x 255.255.255.255 200.x.x.x (it is here to let him speak to the customer)

  access-list 100 deny ip 10.0.0.0 0.0.0.255 10.172.10.0 0.0.0.255

  access-list 100 permit ip 10.0.0.0 0.0.0.255 any

  access-list 110 deny host ip 10.0.0.73 10.1.0.0 0.0.0255

  access-list 110 permit ip 10.0.0.73 host everything

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  !

  CUSTOMGATE allowed 10 route map

  corresponds to the IP 110

  IP 200.x.x.x next value break

  !

  sheep allowed 10 route map

  corresponds to the IP 100

  !

  Add at least:

  > Route ip 10.172.10.0 255.255.255.0 200.x.x.x

  to force the traffic for VPN clients on the external interface. also make sure you hav a route for the clients IP address (not the VPN negotiated one) that also indicates the external interface.

  The fact that the router is not encrypt means that it is not even see the responses from the inside, hosts, which indicates that your internal network is not a road to 10.172.10.0 pointing to this router, OR the router receives responses but sends them back out inside interface which will be set by the first route, I mentioned above.

• VPN - PC (vpn client) problem-> router-> (site to site vpn)-> local network

  Hello

  is it possible to install?

  I have a pc and I want to connect to the Remote LAN.

  PC (using vpn client) - vpn (internet)---> ROUTER1 - a vpn (MPLS network)---> ROUTER2---> SERVER site

  How can I connect to a remote server? Is there an easy way?

  I did the configuration of the vpn client (I can connect ROUTER1 and access a LAN via vpn with 192.168.1.x), but I can't connect to the server, even if I set the subnet (192.168.1.x) under the access list of site to site vpn (access list for traffic that must pass between ROUTER1 and ROUTER2).

  Please advise! Thanks in advance.

  Looks like I've not well explained.

  On ROUTER1

  ===================

  1 ACL VNC_acl is used to split tunnel, so you should include IP server_NET it NOT vpn IP pool.

  2 ACL najavorbel is used to set the lan lan traffic between ROUTER1 and ROUTER2, 2 you should inlcude

  IP 192.168.133.0 allow 0.0.0.255 0.0.0.255

  You must change the crypto ROUTER2 ACL of the minor or the najavorbel of the ACL

  The other way to is to the client VPN NAT IP to a local area network lan IP ROUTER1, in this way, you don't need any changes on ROUTER2. But I have to take a look at your configuration to make the suggestion.

• Web client problems

  Hi all

  I've updated one of my vCenters to 5.5 last earlier and since I can not start the web client.

  It keeps crashing.

  Newspaper wrapper:

  < KE0002I > kernel has started.

  < KE0001I > core of departure.

  (< DE0700E > cannot find the version bundle 'com.vmware.help' range ' [0.0.0, oo)' in the repository 'ext - usr.

  (< DE0700E > cannot find the version bundle 'com.vmware.store' range ' [0.0.0, oo)' in the repository 'ext - usr.

  (< DE0700E > cannot find the version bundle 'com.vmware.dataservices' range ' [0.0.0, oo)' in the repository 'ext - usr.

  (< DE0700E > cannot find the version bundle 'com.vmware.vimservices' range ' [0.0.0, oo)' in the repository 'ext - usr.

  (< DE0700E > cannot find the version bundle 'com.vmware.vim.dataserviceadapters' range ' [0.0.0, oo)' in the repository 'ext - usr.

  I think I may need to reinstall the web client.

  Any body any ideas?

  Thanks Jim

  I have not seen this one before. I found this thread that looks like it could be related. You can try to reinstall the Web Client as you suggest or by opening a SR with GSS.

  vSphere web client 6.0 SDK java.lang.NullPointerException: the component of the VMware Manager URL can not be empty.

• XML - RTF Editor model - no fixed lines

  Hello

  We print a report that is developed in the XML Editor, but user requirement is to print 10 rows on each page under one group.

  I did the following code, the code is compiled successfully, but does not generate output according to the requirement of the user.

  I followed this example never nominate it.: limit the lines per page

  <? for-each: G_SUB_INVENTORY_INFO? >

  Sous-inventaire:	<? SUBINVENTORY? >
  Location:	<? STOCK_LOCATOR? >

  <? for-each: LIST_G_ITEM_DETAIL? >

  Tag # < name xsl: variable = 'rowlimit' select = "number (10)" / >	Item code	Description of the object	Lot #.	Expiration date

  MINISTRY OF HEALTH

  Status

  Counted Qty

  F TAG_NUMBER

  ITEM_CODE

  ITEM_DESCRIPTION 0.00

  LOT_NUMBER

  EXPIRY_DATE

  <? position()? >

  <? If: (((position () - 1) mod $rowlimit = 0) and position() > 1)? > < xsl: attribute name = "break-before" > page < / xsl: attribute > <? end if? >

  E

  <? for - each:xdoxslt:foreach_number ($_XDOCTX, 1, $rowlimit-(count (G_ITEM_DETAIL) mod $rowlimit), 1)? >

  <? position()? >

  <? end foreach? >

  <? end for each: LIST_G_ITEM_DETAIL? >

  page break end <? end for each: G_SUB_INVENTORY_INFO? >

  
  

  Please guide me where I am doing wrong.

  
  

  Kind regards

  Waqas Hassan
  

  Hello

  I found the solution,

  Missed me a number function.

  Before:

  After:

  Thank you