Local users VPN SSL

Similar Questions

• 506th PIX IPSEC VPN allow authentication for local users?

  We have a 6.3 (5) running PIX 506th, configured for Cisco's VPN IPSEC clients. Cisco VPN clients authenticate with the credentials of group fine, but is it possible to use local users to authenicate plu? We use local users to our existing PPTP VPN clients, but we want to migrate these users to IPSEC. Any info would be greatly appreicated.

  Of course, you can... you need to include the command on your card crypto below

  map LOCAL crypto client authentication

  I hope this helps... Please, write it down if she does!

• local access over ssl vpn

  Hello

  Here is the configuration:

  (Location A) - Internet users - ASA (ssl vpn) - location

  situation users use ssl vpn over the Internet to connect to resources in the location b. is successful.

  However, A users location need access to their own network resources internal to A while they are still connected to the SSL VPN.

  So if a user of location is connected to the ssl vpn, they can ping to ip addresses in the location B, but their own network internal ip is second to pings.

  ASA worm is 8.0 (4)

  Please help, how it can be done, and if there is a different Setup for this. Do we need to use the tunnel.

  Thanks in advance.

  Correct, so instead of tunneling ALL traffic, you only tunnel 154.65.0.0/22

  sslvpnsplittunnel standard access list ip 154.65.0.0 allow 255.255.252.0

  Apply the ACL to the SSL VPN group policy

• A single local user can belong to the Group 2-policy?

  I have a Cisco ASA 5505 that I install with a SSL VPN. It's for personal use, and I so didn't need anything other than local authentication.

  I created two group policies:

  internal TunnelLAN group strategy

  attributes of Group Policy TunnelLAN

  VPN-tunnel-Protocol svc webvpn

  value of server DNS 208.67.222.222

  VPN - 4 concurrent connections

  VPN-session-timeout 1440

  Protocol-tunnel-VPN-client ssl clientless ssl

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split tunnel

  blahblahblah.com value by default-field

  the address value tunnel_lan_pool pools

  WebVPN

  internal TunnelAll group strategy

  attributes of Group Policy TunnelAll

  value of server DNS 208.67.222.222

  VPN - 4 concurrent connections

  VPN-session-timeout 1440

  Split-tunnel-policy tunnelall

  Protocol-tunnel-VPN-client ssl clientless ssl

  blahblahblah.com value by default-field

  the address value tunnel_all_pool pools

  WebVPN

  As you can see, I would like to have a profile/policy where I only encrypt data will tunnel of splitting my ACL, and I would like to have a profile/policy where I encrypt all traffic.

  The question ive been fighting is - it does not seem possible to associate more than one group by user policy. If anyone can confirm this? If it IS possible - can you tell me how I associate the two groups to my local account?

  Thanks in advance.

  Edit: I'm running ASA 9.1 (1), 7.1 ASDM. I'd be happy to share several config if requested.

  Hi Brandon,.

  You can always set a group policy on a tunnel-group (connection profile). So in your case, you can create two tunnel and specify each lives in group in respect of each type of tunnel-group so.

  !

  type tunnel-group TunnelLAN-vpn remote access

  tunnel-group TunnelLAN-vpn-global attributes

  Group Policy - by default-TunnelLAN

  !

  !

  type tunnel-group TunnelAll-vpn remote access

  tunnel-group TunnelAll-vpn-global attributes

  Group Policy - by default-TunnelAll

  !

  When you connect, you can decide which group policy you want to apply through the selection of the desired tunnel-group.

  As long as you do not restrict the local user for a specific group (under the user attributes) policy all users can connect to one of the Tunnel-group defined in the ASA so long as they provide key correct pre-dhared

  Please note the useful messages.

  Shamal

• LOCAL + RSA VPN authentication?

  Hi... we have a customer using an ASA 5520 8.2 (2) for VPN (webvpn) connections. Currently, they use the user/pass configured locally for authentication (it's a default, there is no explicit LOCAL configuration).

  They would use their RSA security device, but not for all users at once. Is it possible to use the local database and RSA as points of authentication, i.e. If there is no configured local user name, try the RSA (or vice versa)?

  Thank you

  Jim

  The ASA can do that natively the emergency authentication being quite limited on the SAA. Two possibilities are there to solve this:

  (1) use an external server which can chain these authentication stores (ACS or ISE may be used). But it is a rather expensive solution.
  (2) build more tunnel-groups with different authentication settings and ask your users to use a particular.

  Sent by Cisco Support technique iPad App

• ASA5505 local user database

  Hi all

  I'm need to consider purchasing an ASA5505, local user accounts how can it have?

  Y at - he of the docs to confirm this?

  Kind regards

  Tomoyuki

  Hello

  I don't think that there is a specific number.

  I know there's an option for the VPN or management for example, but you can have an external database for other purposes.

  Federico.

• Mac OS Server - local users on console does not.  The shared access or ssh on account works

  A Mac Mini running Mac OS Server has problems with authenticating the passwords of local users.  Users connect the console of the physical computer running macOS app Sierra and Server 5.2.

  I'm looking for a short solution from scratch user and migrating data to a new installation.

  My hunch is that there is an interaction with the server application.  The other Macs, I managed on the same network fail server and do not have these problems.

  I installed a new version of macOS Sierra and then migrate the old data server on using the migration wizard, but the problem persists.

  The server used to have users on the network, but they are all deleted, and all users are the.

  In application server, the only services running time machine, the caching server and file server.  DNS, DHCP and Open Directory services are disabled in the server application.

  A local user password will work normally when the computer is restarted.  But if the user disconnects, and tries to connect to or use the fast user switching back and forth between accounts, the password is not accepted.  On reboot, it will be accepted.

  In addition to passwords are not accepted, other errors when you try to connect to specific customers include:

  "Your account is not a valid directory.  For more information, contact your system administrator'

  or

  "On behalf of user that you selected is not available."  Check your network connection and try again to the user account.  If you are connected to the network, ask system administrator for assistance. »

  If a network is used to access the data of the user using the user name and password, it works.  Similarly, SSH'ing via the terminal using the username and password works.

  An admin user can change the password back and it usually works for one login.  Then the password is denied if the user disconnects or use the fast user switching.

  Thanks in advance for any help on this embarrassing problem!

  I should clarify: it's the passwords of local users on the Mac who stop working (for the connection or fast user switching), until the Mac restarts.

• Prevent local users to install Firefox

  For some reason, the local users are able to download and install Firefox on their profiles. It installs in their file C:\Users\ < user > to \AppData\ and does not appear in the list of software to uninstall so that the local user who placed it.

  As a system of administration that does not want any user to install ANY software, unless they are using an administrator account, this is very frustrating. How to avoid as local users on our network, without administrative rights to install this software?

  Hello kafri, when the installer for firefox (and many other programs) is run without administrator privileges that he could deliver his program files in this directory to users appdata rather than be installed globally for all users of this computer.
  If you want to restrict that you will have to consider in defining certain system policies as described in the https://technet.microsoft.com/en-us/magazine/2008.06.srp.aspx (this will beyond the scope of our forum, however).

• Localized user interface

  Hello

  I have some problems to reload the complete dictionary (GSD file)

  with the LabWindows/CVI 'User localized Interface' tool.

  DO NOT run a multilingual, with the good translation software.

  The final executable works perfectly, with LWL file.

  BUT if I need to correct an error of translation (I'm only a man ).

  and try to reload the previously saved dictionary (GSD file) for that.

  After leaving the tool,

  many completed translations previously disappeared (see pictures attached).

  You can save the dictionary as much time you want.

  After put again and again... the same missing translation.

  Whenever you reload, after the tool 'User Interface localized',

  some translated lack again and again in the tool.

  See the attached example.

  See with 'Fonction_EN. GDL' and 'OK (enter)' message button of the Panel "in context".

  It is correcly filled in the final file of LWL, so the executable is correctly loaded.

  But it still does not save in the GDL dictonary file.

  We had the problem, since almost LabWindows/CVI 2012 (and perhap previously).

  And especially with some IUR with many panels on the inside

  and/or using the same translations (__OK, __Cancel, etc...).

  Thanks a lot for your help.

  Hello

  A solution was given by another post.

  Sorry, I lost the link.

  Thank you.

  Process:

  LabWindows / CVI-> tools-> localized user Interface...

  -File-> open User Interface (*.uir, * .tui)...

  '... \Elements.uir '.

  --> Dictionary Translation of the dictionary (*.lwd)...

  '... \Elements.lwd ' (-online form "Chains" successfully imported file dictionary)

  -File-> load location (*.lwl)...

  '... \Elements_En.lwl ' (-online 'channels successfully imported the language resource file)

  The translation are fulfilled.

  

• Install Microsoft changed the startup by setting up a local user account

  I installed Microsoft .NET Framework 1.1 and since then had to click my username / load my personal settings to start Windows, which slows startup significantly time. I have a XP Home Edition / SP3 operating system. Microsoft recommends installing the latest service pack for the .NET Framework 1.1 for resolution:

  http://support.Microsoft.com/?kbid=827072

  .. .but I have installed this or no available... I still have an ASPNET local user account that interferes with mine.

  Please note that I am the administrator of the computer, and I have no password... I read:

  For Windows XP Home Edition, do not try to autologin as the built-in Administrator, you will receive an error message?

  * Uninstall does not work, I tried

  How can I fix this please?

  Hello

  Thank you for visiting the Microsoft answers community site. The question you posted would be better suited in the Technet forums. Please visit the below mentioned link to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads

• Local user account

  Hi, on a new computer a local user account has been created and loaded with personal folders.

  Two weeks later, another user account was created with an address of the user online.

  The first user account was deleted with its countain.

  Is it possible to recover the deleted account?

  Thank you

  Not sure if the system restore can restore a user account, but worth a try if you have a restore point before the account was deleted.

  http://www.eightforums.com/tutorials/4692-System-Restore-how-do-Windows-8-a.html

• Suddenly can't access local users and groups permissions list

  In computer management (my computer / manage) "Local users and groups" icon has a red x on it and when I click on it I get this message:

  Local users and groups
  Unable to access the computer {computer name} toa. The error was: library not registered.

  How can I find which library is not registered, so I can register?

  BTW, this is one of several very similar problems that began to arrive after the last update of Microsoft Windows Vista.

  Hello GCCarvill,

  Thanks for posting your question in the Microsoft answers Forum.

  If you have a system restore point, before applying the updates would be the fastest way to restore the library file
  who is missing. Use the following article to restore to an earlier point in time. Don't forget to create a manual restore point before using an earlier version of the operating system.

  936212 KB - how to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
  http://support.Microsoft.com/kb/936212

  You can also create a manual system restore point so that you can restore in case of problems.
  How to create a system restore point manually:
  Right-click on the computer icon in the desktop, then choose Properties
  In the left pane, click System Protection
  Alternatively, to directly access the System Protection tab, click Start and type SystemPropertiesProtection.exe.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  Click the System Protection tab and then click on create.
  In the System Protection dialog box, type a description, and then click on create.

  After the search for the other forums, I found another user having a similar problem. They used a tool called FileMon and after comparison, they discovered a file called activeds.tlb was missing. They have restored a copy in the system32 directory and
  was then able to access the local users and groups successfully. You can download a copy of FileMon of:
  http://www.sysinternals.com

  If please reply back and let us know if it helped to solve your problem or if you need further assistance.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• setting up a vpn ssl to a netgear router

  I have setup a router netgear FVS336G at a customer and you have configured a vpn ssl to the customer. I can cinnect on a win xp machine, but not on my machine which is running Vista 64 bit. I get narrations of error message cannot install the vpn tunnel.

  Hi Jluequi,

  The issue of Windows 7 you have posted is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows 7 networking forum.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Don't Win 7 Home Premium no local users and groups under computer management

  I am trying to create local groups, but when I go into computer Managemmt as an admin there no option groups in the tree.  Aide said it is in "computer Management\System Tools\Local and Groups\Groups users", but the only options I have under system tools are planner of the event viewer, shared folders, Performance and device - not local users and groups management tasks.  No idea how I can get access to this?

  I think that it is only available if you have Windows 7 Professional or ultimate edition. Bob Larson Access MVP

• Win 7 Pro - all users in local users and groups

  Hello I have a new install of Windows 7 Pro with two users; Administrator (built in) and my personal user (CCzahor). I can connect to windows very well with both users.  When I right click my computer and manage them, there is no user appearing in "users and groups / users.  However, if I go to groups, double-click 'Administrators', I see Director listed, and I see CCzahor under "users".  In addition, when I run lusrmgr.msc, I see the same thing as described above, but when I run netplwiz.msc, I see the admin and CCzahor displayed in the list.

  It is not functionally a problem, but rather a nuisance than anything else.  Any ideas?

  Hello

  Please provide a detailed description of the issue.

  I understand the inconvenience you encountered. I will certainly help you with information.

  Note: Users and groups is located in computer management. A collection of administrative tools that you can use to manage a local computer or a remote computer. Please see the link below.

  Local users and groups overview

  https://TechNet.Microsoft.com/en-us/library/cc770756.aspx?f=255&MSPPError=-2147217396

  Important: Under local users and groups, you must click users to see users and groups. And if the two accounts you have in the system have administrator permissions, it's going to be reflective under the administrator group.

  I hope this information is useful.

  Please provide us with the information above to help you best.

  Thank you.