Loop drops when connected wireless (NI 9191)

Similar Questions

• Printer offline depending on laptop when connected wireless

  Hi I have a wireless c309a printer connected to my laptop via a netgear router. My children, off the printer and now it is back on the laptop says that it is offline. I reported a test of the wireless network that says that everything is fine and it is connected. When I put the IP address in the web browser, it tells me that the printer is connected and everything works. So what's happening? Why not print?

  Yes, if the IP address of the printer changes all the time your computer may have a difficult time finding.

  We will set an IP address of the printer:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address). If you don't know it, enter the current IP address.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the gateway and DNS white. Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• Canning Internet connection drops when the computer is connected to the PS3 via an Ethernet cable.

  Original title: Shared network problem

  I am trying to use a shared network, configure as follows. My computer connect wireless to my router. My PS3, however, seems to be really slow when connecting wireless to the router and is at a proper speed when connected via ethernet. So, I have my PS3 connected to my computer with an ethernet cable. I put the wifi connection to be shared. Next, I set up my PS3 to connect to cable internet. Has gone through the steps and connected properly and at full speed too. However, there is a problem. My PC guard 'give up' connection to my router, while remaining connected to the PS3. I have to manually connect to my router again, regardless of the connection automatically option. Almost as if my PC is to use ethernet for internet access, (which he won't get that which is connected to the PS3) and so it loses the wifi connection. This abandonment happens around every 5 minutes or more.

  Is it possible to keep my PC connected to my wireless router and still be connected to my PS3 through ethernet to connect my PS3 using my PC?

  The problem seems to have 'fixed itself. I tried messing around with the connections that would not work even the bridge. Then I've switched back to ICS and did not have a disconnect since then.

  So the problem is now resolved, but don't know how?
  Whatever it is, I am very grateful for your help Manasa, it is well appreciated!

• g 3 drops once connected wifi

  Usually when I'm connected wireless 3 g, says again but in white. Now, when connected wireless 3g grave and only lights up when I turn off the wireless. Any ideas if this is normal after the update?

  I can say I've seen a number of different iterations. WIFI connected without side of 3G, WIFI connected with a white symbol of 3G and WIFI sometimes connected with a blue symbol of 3G. I think someone has explained that a blue symbol means 3G is connected and also connected to Google's servers, where whites: data but not connected to google's servers. Obviously WIFI and 3G can be connected at the same time, so it seems that what watch is not always accurate. It would be good to know what is normal to show.

• Problem of not seeing list drop-down connection to the wireless network when checking connections network - pc windows 7.

  Problem of not seeing list drop-down connection to the wireless network when checking connections network - pc windows 7.

  I just installed a Belkin modem-router - which went well. Can I connect WiFi gadgets etc. I can also connect to the internet via a network cable to my pc. I also installed a belkin usb wireless adapter and in Device Manager, says it is enabled and works.

  My problem is, I have no way of choice get a WiFi PC to display in the list (from the notification area) and cannot get the pc to give me options to create a wi - fi connection. The more I get to try to do that is "unexpected error"!

  If someone could help on this - I would be very grateful

  Good news - update of my ongoing saga with this Belkin modem/router.

  Got the pc to see wi - fi now. It turned out to be the Zone Alarm! As the router has a firewall, I uninstalled Zone Alarm completely. Also, I went into the properties of belkin usb and checked it was the most recent drivers, it does not so I installed them.

  So far so good

  Thanks for the help

  TREV Smith

• Equium M40X - WLan connection drops when using in the other room

  Hello

  I'm using the SATELLITE M40X series PC laptop and using TG585 ADSL2 + Modem / 802.11 g Wireless Router.

  Wireless connection works fine if I use the laptop in the room even when the wireless router is pluged but if I bring my laptop to another room and then disconnected just conection.

  I am living in 3 flat bed room and room are right next to each other on an equal footing.

  * Note: * I use apply desktop PC as well and is not in the same room where the wireless router is pluged, desktop pc has no problem with the wireless connection.

  Any idea?

  Thank you

  Hello

  I think that the reason for this problem is that you WiFi signal is too weak in other rooms.
  You can try to change the WiFi channel and may also try to disable Wlan energy saving
  These parameters may be changed in the Device Manager-> card Wlan-> properties-> Advanced tab.

  But to be honest I m not sure if this will help you.
  I have a similar problem with my Toshiba laptop not
  The WiFi signal is too low in my other room there are two walls and it s clearly perceptible for me when the WiFi signal is ok, and the WiFi signal is too weak.

• HP Envy 7640: Wireless issues when connecting to a VPN

  Hi all

  I just got this printer (HP Envy 7640) of my company. I work from home, I need to be connected to a VPN.

  When I connect to this VPN, my printer (wireless) does not work.

  As soon as I stop my VPN connection, all of my prints are made.

  How to solve this problem?

  My COMPUTER support explained to me that the only why do the job is to stop the wireless connection and use a USB connection.

  Do you have another solution?

  Also, how to change USB connection wireless connection? I found the solution on the other hand, but not like I need.

  Thanks a lot for your help!

  Kind regards

  Juliette

  Hello

  You can print to the printer from a computer connected to the same local network as the printer, by connecting to a USB port, you can print from the same local computer on the pritner, you will not be able to print from the remote desktop, the PC and the printer must be connected to the same LAN to print.

  You should be able to use the wireless on the other laptop, as long as this laptop is connected to the local network and the printer is connected too you can print on it, by connecting the USB cable, we did not unplug the pritner from the local network and therefore printing wirelessly from other computers on this network is available with no difference.

  Hope that helps,

  Shlomi

• network unidentified - when connecting on the wireless

  I have laptop HP Pavilion running Vista.  When you try to connect wirelessly I get the unidentified network error.  The other two laptops at home can connect to radio very well, so there is no problem with the router wireless or SPrint aircard.  I finished everything I could find on the internet about this error - without success.  I spent more than 4 hours with the help of HP, more recently, they had me do a "recovery" to set all hardware and software to the factory settings.  Still no luck.  This computer can connect very well with an ethernet cable.  I can connect wirelessly, but can not go on the internet.  Any ideas?  If so, I don't know much about computers... simple steps would be appreciated.

  Hello:

  What model of wireless card you have in your laptop?

  If you have an Atheros, try this driver and see if that fixes it.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5060880&prodNameId=5060882&swEnvOID=4053&swLang=13&mode=2&taskId=135&swItem=ob-97750-1

  Paul

• Second laptop unable to connect; When trying to connect wirelessly, says connection is successful, but the Public unidentified network, no Internet.

  Hi all.

  I'm really sorry to post this question, I must have read 100 other threads on this topic, but none of the solutions seem to work for me.

  I have a home set wireless network in place, which may not have a lot of problems with it that I have a laptop W7 which has a perfect wireless connection, and also our TV connect when you want, as do our phones and Xbox.

  We bought a second hand Acer aspire laptop for our daughter. It is running Vista Edition family Basic. Even if she had the factory reset done on this, because we can connect to the router with an ethernet cable and it works very well, we managed to ensure that all updates of Windows etc are all complete.

  When trying to connect wirelessly, it says connection successful, but it is to a Public unidentified network, and there is no Internet. Also, even if it says Local access, we cannot connect to the router settings page is.

  I have uninstalled and reinstalled the built-in wireless adapter and updated the driver to do this, he says that he is as up-to-date as possible.

  I checked that DHCP is enabled, we tried dynamic and static IP addresses, we have disabled and re ipv6 enabled, we used the command prompt to reset winsock and stack ip, I looked into msconfig services for service # Id_String1.6844f930_1628_4223_b5cc_5bb94b879762 # Apple off but it isn't here.

  I have a real dislike for Norton / products McAfee and there is none of these on the laptop. We will install Comodo Internet Security, Eusing Registry Cleaner, Spybot S & D and Spyware Blaster as soon as the wireless is configured and that the Windows Firewall is disabled.

  We also have many turns of the spin off the coast and laptops, etc. and deactivation and activation of the adapter.

  It seems that all the usual solutions for the lack of connection are not the culprits this time.

  IPconfig for W7 laptop that works well is:

  Microsoft Windows [Version 6.1.7601]
  Copyright (c) 2009 Microsoft Corporation. All rights reserved.

  C:\Users\Adrian>ipconfig/all

  Windows IP configuration

  Name of the host...: Adrian-laptop
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... : 78-E4-00-D1-5F-6A
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Broadcom 4313 802.11b/g/n
  Physical address.... : 78-E4-00-D1-5F-6A
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::30fd:c01f:ab28:fbf9% 13 (Preferred)
  IPv4 address: 192.168.1.3 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: 13 August 2012 09:16:54
  End of the lease...: August 14, 2012 09:56:23
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DHCPv6 IOOKING...: 360244224
  DHCPv6 DUID customer...: 00-01-00-01-13-B2-5C-FD-90-FB-A6-A5-8F-73

  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {09285A7E-7837-4D7B-994D-C70130D43958}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 15:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:5ef5:73 b 8: 8ed:720:a3fa:1e53 (Prefer
  Red)
  Address IPv6 local link...: fe80::8ed:720:a3fa:1e53% 24 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Reusable Microsoft 6To4 tunnel map:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 adapt #2
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 adapt #3
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  IPconfig for the Vista laptop that works wired but not when it's wireless is:

  Microsoft Windows [Version 6.0.6000]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Adin>ipconfig/all

  Windows IP configuration

  Name of the host...: Georges-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR5007EG Wireless Network adapt

  Physical address.... : 00-1D-D9-1B-71-69
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::78c1:cedd:291c:e44b % 11 (Preferred)
  IPv4 address: 192.168.1.2 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: August 13, 2012 11:28:16
  End of the lease...: August 14, 2012 11:28:16
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DHCPv6 IOOKING...: 151002585
  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Broadcom NetLink (TM) fast Ethernet
  Physical address.... : 00-1B-38-5C-28-24
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  The connection-specific DNS suffix. :
  ... Description: isatap. {E409704E-A039 - 41A 8 - BEB9 - 614B6A018}
  493}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::5efe:192.168.1.2%12(Preferred)
  ... Default gateway. :
  DNS servers...: 192.168.1.1.
  192.168.1.1
  NetBIOS over TCP/IP...: disabled

  Card tunnel Local Area Connection * 7:

  The connection-specific DNS suffix. :
  ... Description: isatap. {CC1DD067-8D6C-4BDE-BCC8 - 13921 941
  532}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  ... Default gateway. :
  NetBIOS over TCP/IP...: disabled

  Card tunnel Local Area Connection * 9:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Any help or advice will be most appreciated thanks

  Norton or McAfee pre-mstalled of recovery of the manufacturer media?

  If so, did you uninstall it AND run the tool to remove the appropriate product manufacturer?

  Download the Norton removal by https://www-secure.symantec.com/norton-support/jsp/help-solutions.jsp?lg=english&ct=united+states&docid=20080710133834EN&product=home&version=1&pvid=f-home

  Close all other programs, and then run the tool. When it is complete, reboot the machine if she wants it or not.

  Download the removal of McAfee Development tool from:

  http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  Click on save and save the file to a folder on your computer.

  Navigate to the folder where you saved the file.

  Right-click MCPR.exe and select "Run as Administrator" to run the removal tool.

  When you're finished, restart.

• My computer can not VAT registration and access the internet when connected to the network [secure] through wireless.

  Original title: fix problem 'local only' what is wireless.
   
  -My computer is a HP Pavilion dv5, running windows vista edition Home premium

  -My computer can identify and access the internet when connected to the network through a cable.

  -My computer can identify and access the internet when it is connected to the grace wireless network [without warranty].
  -My computer can't identify [unidentified network] and [room only] internet access when it is connected to the [secure] grace wireless network?
  -Other information systems, identify and access the internet when it is connected to the [secure] grace wireless network.
  -J' confirmed the network, try password works in "safe mode with network", manually configured (TCP/IPv4) using a connected computer.
  S ' Please, I'm desperate and in urgent need of help.

  Hello

  1. If it works well before?

  2 have you made any changes to the computer before the show?

  Method 1:

  You may experience connectivity problems or performance issues when you connect a portable computer that is running Windows Vista or Windows 7 to a wireless access point:
  http://support.Microsoft.com/kb/928152

  Method 2: Uninstall and reinstall the network adapter drivers.

  Follow the steps mentioned.

  (a) click Start, right click on computer.
  (b) click on properties, click on Device Manager
  (c) expand the network card, right-click the wireless adapter option
  (d) click on uninstall
  (e) now go to your computer/wireless device manufacturer's website, download the updated drivers and install them.

  Follow the below mentioned article:
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Windows firewall stops when a wireless connection is established.

  Windows firewall stops when a wireless connection is established during the start-up or wakup or manually connected via wireless.  The firewall can be activated manually after wireless connection is established.  Firewall survives boot and reactivation if computer connected to the router via ethernet (cable).

  OS is 32-bit Vista Home Premium, SP2.  The platform is Acer A4720Z dual-core Intel laptop.  Wireless adapter is integrated Atheros AR5007EG - Atheros 7.70.396 driver (whidh is current & compatible Microsoft version).

  Current virus/firewall is MSE and MS Firewall.  No firewall problem until the installation of Security Essentials.  Previous virus/firewall was Mcafee SecurityCenter Suite that uninstalled cleanly via the Remove Mcafee (MCPR.exe) utility.

  All the relevant ideas welcome. Thank you.

  Go to network and sharing Center and then choose manage wireless network and try to remove this Wireless if it is there and try to add it again if you want. Try to upgrade Microsoft Security Essentials and also check for update for Windows. Also, run the full system scan and remove potential threats. If the problem has not resolved then contact technical support:

  https://support.microsoftsecurityessentials.com/

• Why can't I access the modem 192.168.1.1 when connected to the wireless router?

  I'm unable to access my DSL Modem 6100 Westell using 192.168.1.1 when connected to the Netgear WNDR3400 wireless router. I can access it, however, when I connect directly to the ethernet port on the computer without going through the router. I've set up according to the instructions. Is it possible to correct the problem?

  This isn't a problem.  This is the standard behavior.  You are connected to the side LAN of the router that is isolated from the side WAN (uplink).  This is the mode of operation of routers.

• DeskJet 3510 not found when she and my PC are connected wireless

  Hello again,

  When my Windows-8 HP Slimline Pavillion is connected to an Ethernet port on my router wired, the installer for my 3510 (already well running wireless - is no longer cable) can perfectly find.  A my scan application and printer home page on the work of PC (display of ink, etc.) fine, as does impression on her.

  The 3510 has a fixed IP address in my router (see my other post on airprint not working do not).

  My HP machine, if you unplug the Ethernet cable, everything is configured to connect wireless to my router (which she does very well and gets me internet access, etc.).  It ias 1 set (static) IP address in place in my Cisco/Linksys router to the wired connection and a second (static) for wireless connection - because the HP machine has different addresses for Wi - Fi and wireless.

  My problem is when BOTH my PC and the 3510 are wireless, printer configuration 3510 CANNOT find the printer 3510 is clearly there and running.  The applet or task of scanning bar shows "plugged in."  He said that the tests are not available.

  In summary, everything works when my PC is wired and the 3510 is wireless, bit does not work when both PC and the printer are wireless.

  Ideas?

  Thank you

  Norm Farrington

  Router changes are documented in my other post. See 3510 tags and airprint to find.

• How to condigure guest OS when you use net mode bridged when connecting by local security-enabled wireless network

  I am running VMWare workstation on a host with the guest OS Windows XP and ubuntu.

  I work in a place where we have a LAN wireless - security-enabled.

  When you use the NAT configuration - my OS comments doesnot seem to be able to run and use the DNS and the Windows network AD features.

  -I want to set up the guest operating system to connect to the network using the bridged mode.

  Unfortunately - the 'visible' for Windows XP network connection is reported as a wired lan connection. This means that I am not able to configure options for the connection wireless security.

  Is there a configuration missing that I forgot, I have to do on my wirtual machine, toolsthat host or vmware would allow this Setup program begin work?

  Plese - if anyone has som einput it would be greatly appreciated.

  Best regards

  Poul Christiansen

  Wireless configs should be set to the host OS, unless the wireless usb is attached directly to comments.

  For mode bridged you have, connect to the guest is actually nothing else that a wired connection and XP won't be able to use it as wireless (except usb of course).

  This means that your association and authentication to the AP will have on the host operating system linux tools.

  Joakim

• After reinstall, Windows Vista guest is no longer to set "network location" when connecting to a wireless network. How can I do it again?

  Hard drive failure, had to reinstall Windows.  Among other random things that are annoying, I noticed that Vista wonder is no longer for what kind of network, I connect to.  I fear it may default to private even if I connect to a public network.  How can I do ask the question again?

  Hello again Amit,

  Have you tried uninstalling and reinstalling your network adapter?
  See if Windows prompts when connecting to your network after the execution of a reinstallation of the card:
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly