M276nw: Error 49 M276nw

Similar Questions

• Service error 49 - Turn Off, then on - LaserJet Pro 200 M276nw

  I was the addition of another post for a different printer but didn't want to Miss anyone with MY printer problem.

  UPDATE * (at least for my LaserJet Pro 200 M276nw)

  I found the cause but will need help from someone at HP to "solve" this one...

  My new guard M276nw throw a 49 Service error, CAT has given a lot of power, voltage on, wait, try again blah blah blah, blah blah fuser problems. 10 minutes from the forum search put me on possible wireless network issues with other printers and the SSID. Anyway after regaining a printer Staples and saw the problem coming up again on a new another brand... I tried the search Forum and Tada! at least I was able to find a cause.

  I have a D - Link DIR-825 wireless router. He has dual band (2.4 GHz and 5 GHz).

  Normally I enabled for the multitude of devices that people have these days in my house.

  I updated the firmware to the last update (20121026) and then restarted.

  Roger restarted shortly after error Service 49.

  Then I disabled the two strips to test each independently wireless band.

  The printer acted normally so I decided allow each band separately.

  When I turn on the 2.4 GHz band in the router, the printer immediately throws an error in Service 49.

  I tested several times (5 to be exact) and every time when the router restarts the printer says error.

  So, I left off 2.4 GHz band and then the 5 GHz band.

  I activated the band 5 GHz 3 times and turned off and found no effect on the printer (at least in a 5 minute window).

  So now I'm left with only a single band wireless router or printer who likes to turn on every 20 minutes or more.

  There is probably a setting (or 2) which can be changed in the router or printer that can prevent this (I hope).

  I just need to find the right person in HP...

  I should have updated this thread I'm sorry, but I found myself updated the same problem on another thread of printer M251nw, since someone has answered that one. I have to keep that one thread - sorry, but it seems to me that I just heard another as well, but for a m475dw as well. Maybe the same problem that I don't know.

  Anyway to update my m276nw situation: After experimenting for a while try to limit I decided to eliminate the possibilities by disabling my router another suggestion of posters to remove the printer from the wireless environment and reset to factory settings. So I turned off my 2.4 GHz band in my router (leaving 5 GHz active), reset the printer and it was sitting still (no reset), he even went to sleep normally. I turned on the 2.4 band and the printer immediately threw the error repeated tent kept the same result no way to leave on the 2.4. The next day so I decided to check my router and found 2 year old firmware. It took several updates to get current and on the last I didn't reset the printer to the factory again and there's no error yet. The printer acted normally for a week, he normally sleeps and wakes. It was turned off (on purpose) a few times and everything seems normal.

  I have not activated wireless again since my house is wired and I could really do without wireless capability, but eventually I want to know.

  My DLink DIR-825 router is still active with both tapes, but using the latest firmware, like the new printer (the other). Is all this took?

  Perhaps.

• LaserJet Pro M276nw: M276nw LaserJet Pro 200 connection error / update Firmware

  I'm trying to update my firmware on my printer wireless.  The current Firmware Datecode is 20121026.  I have run the wireless network Test report and the summary network and it shows the printer connected and on the correct home network.  I have no problem printing, however, when I go to Check for Updates I get the following message:

  Connection error

  The printer cannot connect to the service.  Check the Internet connection.

  Any suggestions?  Thanks in advance.

  OK, you got it the second time. Not all of the SAP is unified in the layout. It is more difficult to stay on top, but you found it. Ok. Always make the mistake so. This is not good.

  Looks like the printer is blocked. You have reset the network?

  Turn the printer off and unplug the router for a minute. Then when the network has restored himself to try to update the firmware again.

  You may need to update the firmware via a USB connection. This link will take you to the page of software and the printer driver. Software and pilot results for: HP LaserJet Pro 200 color MFP M276nw.

• HP Laserjet 200ColorMFP M276nw: PCL XL Error, HP LaserJet 200 ColorMFP M276nw, Windows 8.1

  Printer: HP Laserjet ColorMFP M276nw 200

  Installation: cable network using the complete package PCL6 (last available online)

  OS: 8.1 64-bit Windows

  Problem:

  When you print to some programs (for example the Page of Test, Microsoft Word), the printer prints a page with the following text:

  PCL XL Error

  Subsystem: kernel

  Error: IllegalTag

  File name: kernel.c

  Line number: 1921

  Printing from Notepad works very well. Printing on other computers on the wired network is working properly.

  Troubleshooting steps:

  1. Updated firmware update
  2. Uninstall, and then reinstall using the latest version of the software available online
  3. Changing to optimize for the text on the Advanced tab.

  Thank you for your help.

  As explained above, it could be a fault of the driver, or intermittent corruption by the hardware, or (as http://h30434.www3.hp.com/t5/Printer-All-in-One-Software-Drivers/M175Nw-PCL-XL-errors/m-p/4940252 says) the result of a recent update of AVG anti-virus.

• LJP Color MFP M276NW 200: the 49 Service error

  Printer worked fine for about 12 months. Suddenly get this error 49 service and won't go away, despite the power cycling.

  It was on a wi - fi connection, but it does on ethernet cable too.

  Click on the Windows icon at the bottom left of the screen

  Start typing: devices and printers

  When you see devices and printers in the search results, click on it.

  Right-click on your printer, and then click on see what's printing

  Right-click on the job at the top of the list

  Delete it!

  If my answer has solved your problem, please mark it as a solution by clicking on the button under the post.

  If any Tech gives you helpful suggestions, you can thank them by giving them "Well done" (just click the "Thumbs Up" button under the post).

  If you're in the right mood, you can even click on the two buttons...

• LaserJet Pro 200 Color MFP M27: LAN error 79 LaserJet Pro 200 Color MFP M276nw

  Hello. I read all related messages in the error 79 in strawberry forum that nothing works.

  I've updated the latest possible firmware. There is no print job in the queue. The power supply cable is directly connected to industrial food, no UPS...

  It worked fine when I installed the printer a couple of weeks or if there is, but now, at the time the printer is on bike starts: 79 - restart - error 79 - error reboot and so on and on.

  It seems related to the connection to the local network. If the printer is in wireless mode all works perfectly.

  Any ideas? Thank you

  Hi @Rand_xi,

  I read your post and see that you have found a 79 error when using the Ethernet connection. I'd love to help you.

  If you manually set the IP Address of the printer, make sure that it is outside the range of your router's DHCP. I saw this to fix this on another post, I've had before.

  If you're still having problems, restore the default settings of the printer, and use the automatic IP address that is assigned to the printer to see if that helps.

  Try disabling IPV6 on the printer to see if it makes a difference.  Go to settings, network configuration, network, IPv6 Services and turn it off.

  If you appreciate my efforts, please click on the button below the thumbs up.

  If there is anything else I can help you, let me know. Thank you.

• M276NW: HP laser Jet MFP 200 system stops at 99% with "fatal error".

  Hello

  I am trying to install this printer. I downloaded the latest software package (version 15.0.15188.2008) and I have followed the installation procedure (being very careful not not to plug in the USB cable until you are prompted to do this).

  However, it always stops at 99% of the balance sheet that "there is an unrecoverable error produced - the installation took too long. I have reflected on old posts, but could not find any "smartinstall" on the PC but smartinstall was abandoned anyway?. And other documents are deleted.

  Why is that makes the HP printers great but absolutely bad software quality? I worked with HP printers for 25 years now and software installations were ALWAYS the link ever sinces USB connections were invented.

  Update: did it, after turning off Smart Install printer (settings, services). That did the trick:

  • So, uninstalled the HP software that I could find
  • Cable unhooked in both ends
  • Restarted printer
  • Smart installation Off Set
  • Package complete last downloaded
  • Re-run starting with shift-right click "run as Administrator" (auth network problem)
  • Follow the installation instructions (invited very carefully removing USB cable until)

• Configuration of scan file on HP LaserJet 200 colorMFP M276nw

  Hello

  I'm trying to set up my printer to scan to a network folder.

  HP LaserJet 200 colorMFP M276nw

  OSX 10.9.4

  WLAN (printer and office on the same network)

  Here's the problem; No matter what I try, I can't have the printer to scan directly to a network folder.

  When you test the connection I get either the ' invalid password or username "or the error"unable to connect to the network folder.

  It seems that the biggest problem is the printer in the right network folder referring.

  I shared the folder, but I can't get a valid path name, that apparently.

  Show folder properties: / Users/vdlely/Dropbox/max verhuur/Scans

  Obviously, this is not complete; I need to add the location of the machine, such as: //iMac-van-AJ/Users/vdlely/Dropbox/max verhuur/Scans right?

  No matter what combination I try, nothing works. I used the name of the computer, IP, with and without login etc etc.

  What is the correct path in my case?

  It would be MUCH easier if you have added a simple browser to navigate to the correct location.

  Please help me to set up right.

  Hi @Aernoud,

  I see by your post that you are having problems for parsing of the configuration of the network folder. I can help you with this.

  I have provided a document to configure network scanning.

  How to perform a scan: from the control panel (including the Scan to Email, in PDF format, and to a network folder).

  Please try the following steps:
  
  1. create a new folder on your computer.
  
  2. right-click (CTRL left click if you use the keyboard of the Mac) and select read.
  
  3. unlock the screen, set all term read/write &, located under the share permissions &.
  
  4. enter in System Preferences > sharing, then select, sharing files in the left bar.
  
  5. click on the Options button, mark the share files and folders using SMB (Windows) and click done.
  
  6. under shared folders, click the sign more and select the configured folder.
  
  7. ensure that "everyone" permissions are set to read & write under the list of users as well.
  
  8. you will see the IP at the top of this screen, make a note to configure the EWS page.

  I think that in consequence of this model of path, you should be able to implement.
  
  Name of the computer or IP address/Shared-folder-name of the computer

  or

  -The computer name or IP name of the computer-folder-address\Shared

  Find out what the name of the computer as follows:
  Go to the Apple/Mac/More report information software/system about / click on the left side on the right side, it should show the name of the computer.

  NOTE: The folder must already exist. You cannot create the folder in the built-in Web server.

  To find the path of the folder where the scanned images are saved, hold CTRL and click on new folder
  created / click on get info/verify shared folder/then copy it to the folder path.

  User name - the name that you use to connect to the computer.
  
  Password: the password allows you to connect to the computer.

  Please let me know if it worked.

  Thank you.

• HP LaserJet 200 color MFP m276: HP LaserJet 200 color MFP m276nw - scaning problem

  Dear gentlemen/ladies, Documents on the flatbed scanner / / UH m276 Color MFP HP LaserJet 200 cannot be scanned in the network folder, scanner, in my office by WiFi. He keeps giving the error message "username or password is incorrect. This user account and password are valid. "Please note that the wireless test is successful. A such problem, until the desktop computer (some bad sectors on the hard disk) has been repaired at the shop of the computer a week ago. However, I can use apps in my office to print and use the HP LJ200 M276 Scan to scan documents on the printer tray and save it in any folder remotely via WiFi. Please please advise solution/method that I can do to solve this new problem. Stephen

  Hi @U-Talents.

  Welcome to the Forums of HP Support! I read your post and see that you are not able to scan to network folder. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  I have provided a document to configure the scan to network folder. Follow the steps, there is a section to create the folder and set up the sharing and security:Scan of the control panel (including Scan to Email, in PDF format, and to a network folder) for HP LaserJet Pro 200 Color MFP M276n and M276nw.

  This post is @wardell1, it can also help with this error message: try to configure the scan to network folder, name of user and password is incorrect. Do not take into account the model.

  I have also provided a @ShlomiLstation, on the same issue: scan to network folder fails.

  Try these documents to see if they help, and if there is anything else I can do, let me know. Thank you.

• Not connected HP LaserJet Pro 200 M276nw

  Hello! I have the Setup:

  OS: Windows 7,.

  Router: TP-LINK TL-WDR4300

  Printer: HP LaserJet Pro 200 M276nw

  Freeware antivirus: Avira

  Firewall: Windows

  The computer connected to a network via ethernet. I installed the network printer (port TCP/IP wirewless, user good reading/writing, shared printer, 6 PLC) and printed all documets in 2013 of Word, it's ok.  After restart of the operating system, printer of the icon is grey and the State not connected. Please help me. Impression of uninstall and install now, Stoped ptrint service, coil clean, reserved IP address of the printer, it all no results.  Some other customers printed successfully via wireless to the printer.

  Hi @green_wanderer ,

  I see that you are having problems printing via the wired or wireless network after restarting the computer, the printer icon is grayed out and showing not connected, but can always print from other computers. I want to help you solve this problem.

  Is the installation of the printer wirelessly or through an Ethernet connection?

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  I would have to power cycle the router, the computer and the printer to see if it will help.

  Print a configuration page to check the firmware version and see if you have a valid IP address.

  If you have a valid IP address for the printer, then try and access the webserver shipped off to the printer, to see if the printer is still on the network. Type the IP address in the address bar of your web browser. (Internet Explorer)

  The IP address of the port on the computer can be different, if the printer has been assigned a new IP address of the afer by restarting the computer. You will need to create a new port, or run the Add Printer Wizard.

  Other computers that are still able to print could have the port configured to print if IP address changes.

  Print a configuration page to obtain the IPv4 address of the printer and the date of the firmware. Printing a Configuration report.

  The new Version is 20140919.  I've provided the URL if you have an old version of firmware update.

  HP LaserJet Pro 200 color MFP M276nw drivers.

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. Find and fix common printer problems using the tools of diagnosis HP for Windows?

  If the problem persists, install a static IP address to see if it will help.

  Printer does not maintain a Wi - Fi connection. Proceed to Solution 3: printer of the assign a static IP address.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If you need help, let me know.

  Good day!
  Thank you.

• Printers Multifunction LaserJet Pro 200 m276nw: memory is low. Job cancelled

  Hello

  I'm new to the forum.

  I have a problem with my Laserjet Pro 200 with a message "memory is low. Cancelled work. »

  I read the other posts with similar questions and tried to do a hard reset to turn on him for 30 second and turning point. The message always appears.

  I tried to update the firmware, but the printer says that no updates are.

  I use a Mac Mini running on 10.9.5 software. I tried to update the firmware via USB, what has not worked at all.

  How can I access the memory of the printer and clear the whole print or add memory to the printer?

  I need help!

  Hi @Med_Stud10 ,

  I read your post and see that you have found an "Out of memory" error when you try to print. I will definitely do my best to help you.

  Check the name of the driver that is installed by the printer. Make sure that it shows just the name of the printer.
  Click on the Apple menu, click System Preferences. Click on Printers & Scanners, highlight the name of the printer on the left side and right side of the screen it should show the name of the printer. (Laserjet M276)

  If the full name of the printer is not correctly, delete and add the printer name back from the list. Click on the sign - to remove the driver and then click on the + sign to add the driver, you may need to click the drop-down list to select the printer name to add it in.

  Try to print again.

  I've provided the steps to set up the printer via the IP Protocol, if the problem persists, which regulated the other 'Out of memory' errors

  Print a Configuration page to get the IP address of the printer. M276n of MFP HP LaserJet Pro 200 color and M276nw MFP - print a Configuration report.

  Remove the printer in printers and Scanners.
  Click on the + button, select the IP Protocol on top, type the address IPv4 of the printer, select Jet Direct below and then apply.

  Try to print again.

  For the analysis, however, you can select the printer Hello.

  If you're still having problems, try the reset I will send you a private message.
  In the forum next to your handle name simply click on the envelope to see.

  Please let me know the results.

  Good day!
  Thank you.

• HP Laserjet Pro 200 Color MFP FAX answering machine vs M276nw

  We have the following MFP: HP Laserjet Pro 200 Color MFP M276nw

  Our office has a phone line to be shared between the phone and FAX (M276nw). The phone is a phone single line of integrated with a digital answering machine Panasonic KX-TG7531 model. I can't seem to find the right combination of settings for ringtone for the phone and the FAX that allows callers to leave a voicemail without the FAX modem tones interfere when the caller leaves a voice message. It's as if the fax does not recognize that the answering machine picked up and he continues to make sounds of modem. The tones are saved as well as the message of the caller's voice, which makes the message difficult to understand. In most cases, the caller simply hangs up without leaving a message (we've heard talk about this later).

  Please tell us how to implement. Thank you!

  Furthermore, the HP Laserjet Pro 200 Color MFP M276nw replaced a MFP from brother, but the Brother FAX has worked with the same phone from Panasonic.

  Hi crmarrio

  I understand that you are having problems of fax.

  Run this test for the fax.
  In the home screen, press the button on the key.
  Tap the service button.
  Tap the fax service.
  Touch run fax test.

  Check all these fax settings.

  Here is a url for the fax troubleshooting.

  http://support.HP.com/us-en/document/c03363598

  Go to the icon/fax setup menu/Advanced Configuration key / private receive/disable it.
  Go to thewrench icon/service/fax service/error correction/stop.

  Go to Settings icon/fax thewrench / fax/advanced/change configuration to speed it to the middle.

  Go to the key icon/fax installation base/menu Configuration/response/game of rings rings.

  (if using an answering machine-more rings on fax and answering machine or rings of mail without a voice for the fax, but receives no voicemail, should get installation of distinctive ring on the line in this case)

  Go to the key icon/fax setup basic menu setup/response/selection of auto mode.

  Go for a key icon/service menu/fax service/clear saved faxes

  Go to key icon/fax installation base/menu setup/distinctive ring/set for proper ringtone type. (if you don't have a special ringtone set on all ringtones.

  Update the firmware of the printer by usb connection.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&docName=c03363598&LC=en&product=5097654&

  Let me know the results of the fax test, and if you were able to send or receive a fax.

  If you're still having problems, let me know and I send you private message how to reset the printer.

• Unknown origin of black sheet pulled from a HP LaserJet Pro 200 M276nw

  We got a paper jam on our printer. One of our employees then pulled this black sheet of our HP LaserJet Pro 200 M276nw. This could really be an original work of this printer? Never seen such a thing before, mayby it's just a few packages that I have inside? The printer does work more (paper jam error). Thanks for helping out.

  

  Hi @VL14 ,

  I see by your post that you had a paper jam and the black sheet was removed from the HP LaserJet Pro 200 M276nw while removing the jammed paper. I would like to help.

  Yes, this part sounds like something to do with the material of printers. The printer would need to be repaired.

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Have a great day!
  Thank you.

• m276nw MFP on Windows server 2003 R2 64-bit

  Hello

  I can't install the software for HP M276NW MFP on Microsoft Windows server 2003 R2 64-bit.  The error screen indicates that the system is not supported.

  What can I do whit it?

  Hi Jaroslaw,

  I can't wait to hear that you have questions.  Unfortunately, the software will not work.  Click here to review the specifications and requirements of the system.  If you want to learn more about your product, click here.

  I hope this helps!

• HP MFP M276nw: y at - it a driver of the HP MFP M276nw sierra

  Printer can be added through add printer process.  Print shops.  Not even a scan option!  Any ideas?  Thank you!

  Hi @LJA53,

  Thank you for joining the HP Forums!

  I noticed your post that you can not scan with your printer HP Laserjet MFP M276nw on Mac OS X 10.12 Sierra. I am pleased to see that for you!

  According to the website Software and Driver Downloads , I see not all the drivers for this printer for Mac OS X 10.12 Sierra. Have you tried using Apple Image Capture for scanning or the HP Easy Scan software?

  If none of these work programmes, all we can do is wait for the software and drivers to be released, or plan to use Mac OS X 10.11 El Capitan until the software drivers come out.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  I hope that this post helps!