magnetic cable

Similar Questions

• Cable magnetic charger without Dock

  Hi Sony users, I recently bought cable magnetic charger without Dock of an online shopping portal. It looks like a USB charger, except for the fact that, instead of USB, PIN, it is a magnetic (he doesn't have a Dock). I just want to know if this product is truly from Sony. Because in the Sony Web site, under the "Accessories" section - I could not find this kind of product and the product is entered into the genuine Sony product package.

  No, probably not. Sony doesn't sell magnetic cables. Sony only sells magnetic docks.

• Is it safe to use 3rd-party magnetic charger?

  I think about to buy the magnetic charger for my Xperia Z2 cable, but I am worried about their quality and their possible damage to the battery from the phone, I am quite satisfied with the performance of the battery, but how will this affect
  It? Also, linking to my normal wall charger adapter that I use for magnetic cable usb charging?

  Would be great if Sony had cable official magnetic charger except the docks. Thank you, best regards!

  Hello

  I used a 3rd party magnetic cable for a few months of battery to recharge my ultra Z and few of my friends use these cables for almost a year now and he has no problem with it.

  Yes, as long as the cable is of high quality, then avoid any injury.

  However, remember that you would use these cables at your own risk. I just shared my experience.

  You changed your answer, and here's the answer to your other hand > Yes, you can plug it into the charger, you got with your Z2 and that everything works perfectly fine.

• Failure of the software update, try to disable to load but it lights again and again

  Hello, I installed Lollipop but PC Companion insist an update exists I was completed by a faulty update of software startup message, my mistake was trying to update with the battery with 65% of the load. And don't remember not what happens, but I'm done with the software update failed error and the phone switch works and market with the same message, I read the other post about turn off and load, but I turn off with the little red button to force it, but if I connect the magnetic cable or usb cable to power it on again , I force to turn off and and the phone turns on again (with the message update failed). It is this normal? I left more time on the phone like that but "load", this will dry the battery? What do I do? Thank you

  Try a system repair using PC Companion as this will often fix questions - this will be factory reset your phone and erase all data

  Turn off your phone and unplug the PC (Hold to increase the volume and power for 10 seconds)
  Start PC Companion and select the area of support then updated my phone/Tablet then blue fix my phone/Tablet and follow the instructions on the screen - when prompted connect your phone turned off always press and hold volume or back button - this should begin the process of repair or reformatting

  If you use Windows 8/8.1 or a 64-bit operating system and then adjust the settings for PC Companion and run in compatibility mode and choose Windows 7 or XP

• Problem loading Z2 and sound problem

  Hello

  I was facing this problem recently where I'm wrong took the magnetic cable sony and plugged incorrectly on my Z2 xperiz.

  This was after the 5.1.1 update.

  All of a sudden, my phone did not start using my power of sony Bank and a charging cable quick, that I got afterwards upward and running.

  But the battery drains now how anyone, regardless of the use less.

  A battery that is used for the last days 1.5 with me now barely lasts 9hours without doing anything.

  The battery keeps fluctuating when it reaches 90%.

  A change in two outlet stores, z2 specific cables have not helped

  Three repairs, a new image, two complete resets didn't help at all

  Second question

  The sound is all of a sudden considerably low,

  I have the sony mdr-nc31e, which seems to be much lower than what it was in.

  Once again the repairs did not work, the Equalization does not seem to work any longer.

  and the sound does not seem to come from a speaker from a two, this is the model D6502.

  What is your opinion on that?

  Although the Sony forums have failed.

  I ran a check with the voltmeter.

  What has been found, it's my battery did not receive enough power and this kept fluctuating.

  Given a sony Center who said that I need to replace a battery.

• How can I maintain lanpscape all the time?

  Hi, I want to keep (the screen not camera) mode of landscape all the time. I tried to disable the automatic rotation and it go to protrate mode immediately. Why don't we have a landscape mode? Or we simply isn't pure auto rotation mode?

  @Hosais

  The only way Sony Home Launcher will continue to run, is that if you are using a Dock or a magnetic cable, other than that, it won't work unless you use a third-party thrower.

• Loading with interruptions, screen turns on and off

  I always put my phone in silent mode and plug it in before going to bed. I noticed it turns the screen several times during loading. I can't that assume this is caused by the brief on the charger, the screen always turns when the phone is connected.

  When the battery is almost full, it often becomes extreme the screen starts to turn on and off quickly. This morning, I took a screenshot of the use of the battery before disconnecting. It shows a decrease in the rate of load to 100%, indicating my phone set on another light show.

  I tried two different Chargers, (one came with the Z3C we speak, the other with my Xperia V) a magnetic cable and mini-usb ordinary and even three Sockets different. Problem persists.

  While I do not notice an impact on the performance of my farm, I'm afraid that it will destroy my battery finally. My phone is only six weeks old. Someone at - he seen this before? Any ideas to fix this?

  

  Hey guys,.

  I finally thought to it: it turns out that a clock plugged into another outlet in the same room was the cause of the problem.

  I hope that my battery was not too suffer from these sessions of loading bumpy.

• The Z3 in car taxation

  Hello

  I got the Z1 and problems experienced with load in my car. I used Windows for Xperia Z1 support with charger cigarette power power combined through the magnetic charge stems on the side. I have lived the times where the henadset the spokesperson for me that the handset has not received enough power to be able to charge the handset. I read in several places on other people having this problem too. Now, I bought Xperia Z3 and do not buy a new Windows support. Instead, I want to buy a magnetic charger cable and use a cigarette charger, with USB Sockets. Already, I've evaluated due to (I think) 1000mA.

  My thoughts are:

  1 - is the handset Xperia Z1, which had problems with the load? (I never xperienced this issue with the dock that followed in the package)

  2. the Sony for Xperia Z1/Z3 chager is estimated to 1500mA. The cigarette 1000mA charger going to cut it? I'm looking at a cigarette chager estimated at 3100mA, with two USB connectors, but I do not know if the magnetic cable can even use this amount of power? I read of others having problems with cables to get hot and combined being turned off by the perception in this way. The cable that I look at is 1 meter and not an original Sony part, but I have no other info on fx amp how much he can handle.

  3. which method of loading is most effective? Megnetic or USB port?

  Best regards

  Frank

  I used Hama dual usb charger with 2. 1 a and 1. 5a. He was able to load Z1 while using the gps and the screen on the use of magnetic cable and 2 AGP port.

• Slow loading dock?

  I recently bought a my Z2 magnetic charging Dock (did not get one with the package) and I noticed that the loading rate was much slower than the normal charge rate of the USB cable!

  Is this normal?

  Yes, it will load more slowly. I have a magnetic cable and it loads slower than the direct output with the adapter.

• Xperia Dk31 z1 has the same cable EC21 and magnetic connector as in Dk36 for Z2?

  Hi guys

  I still can't get an answer (personal Xperia does not respnod) for a simple question:

  Dock station is the Xperia Dk31 z1 has the same cable EC21 and magnetic connector as in Dk36 for Z2?

  If so, that I could disconnect DK31 cable and load Z2 with magnetic original cable... ))

  Someone knows for sure please?

  Ask the user to this category:

  http://talk.sonymobile.com/T5/Xperia-Z2/magnetic-charging-dock/m-p/687915#U687915

• Cable magnetic original sony charger

  Hi there, I am looking for a charger cable magnetic sony xperia z3 Compact? I found this model Sony DCU 28 bu I do not know. It's a straight cable for xperia z3 compact. I want a genuine product from Sony.

  Best regards

  @z3compactw There is no magnetic original cable. There are only original magnetic docks. What you can do is to pull the cable out of the dock. I know EC21 is a Sony cable but not sold separately, so you can find it in a dock for ultra Z for example (DK 30).

• Can I use the magnetic charger shows to recharge my iPhone or it only works with the watch?

  I'm looking to see if my Watch magnetic charger will also charge my iPhone. Can someone help me understand this?

  Hello

  Non - magnetic charge cable only works for load your Apple Watch.

• Satellite 5200 - powers automatically (sensor/hall-magnet)

  I have an automatic feeding weird issue with my laptop Satellite 5200.

  * Situation. *
  1 laptop is turned off and the cover is open
  2. I close the lid while the laptop is always off (just battery is connected)
  3 result: the laptop automatically and boots: how weird is it that

  It has something to do with the magnet that is integrated in the screen/lid place/located near the right hinge. When you close the magnet is close sensor (hall sensor) and apparently, this magnetic field causes the cell to initialize. Normally, if your laptop is running and you close the lid of your laptop computer goes into mode sleep with this technology (magnet and sensor). My laptop works well if she runs and I close the lid. Then it goes on standby as expected. When I opened the lid he returned from sleep mode.

  The issue I am facing now is really just when I close the lid, * while the laptop is turned off already *.
  How do I fix this behavior stupid - how to adjust the magnet/sensor so it has not received the impulse to automatically feed upward.
  The solution must be around here somewhere. And I don't think it's a software configuration problem, because the laptop is turned off when this occurs - so no Windows is running, it is not in standby or hibernation mode.

  Your help would be appreciated.

  Thank you very much for your advice!

  Hello

  If he s really a lid switch problem then it would mean that there is a mechanical problem that could be solved by a service partner
  But I think that this is not a sensor problem possibly display frame/cover touch the power button (that's my opinion) and that feeds on the new laptop

  Just a question; What is cable LAN connected to the laptop when the laptop automatically?
  If Yes, then I would recommend checking the BIOS if the Wake up on LAN option could be disabled
  In many cases, it would lead to the reactivation of the laptop

• display cable

  MY Apple Watch more than four hours shut off and on screen display to show green with the charger cable

  and I can't turn on

  What should you do?

  Hello

  When you reload your watch, check that:

  • All the plastic film was removed from both ends and both sides of the cable support (consult closely on the head of the charger).

  

  • On the back of your watch and the head of the charge cable are clean and dry (clean with a lint cloth and try again).
  • The Chief charge is directly aligned with the back of the watch, with the curved side touch fully (some stands watch may hinder this).
  • You use only the genuine magnetic Apple Charging Cable.
  • If you reload your watch by plugging into a power outlet, try using different maps of the following:
    • The real Apple USB Power Adapter that came with the watch, or;
    • A true 5W Apple (iPhone) or 12W (iPad) USB power adapter, or;
    • Power adapter certified by Apple (MFi) third 5W or module of magnetic charge.
  • If loading via USB, make sure you use a USB 2.0 or 3.0 port, the computer remains turned on and awake, and the cable is plugged directly into the computer (not on, for example, an external keyboard).
  • In normal operation, the load should take up to 2.5 hours.

  More information:

  Check your battery and load your Apple Watch - Apple Support

  After leaving time for your watch load, try removing the charger and restart or if it does not help, force its restart:

  -Restart: press and hold the side button until you see the cursor off the power, then drag to turn off (wait until it does), then hold down the side button until you see the logo.

  -Force the reboot: hold down the side button and the digital Crown for at least 10 seconds, until you see the logo.

  If you still have problems, contact the Apple Support (mail service may be available) or make a Genius Bar reservation in order to have your watch and/or verified under guarantee of power accessories:

  https://www.Apple.com/support/watch/contact/

• Cable vs. Ethernet SFP switch

  
  

  1. you don't need a cable crossed to these switches. They are auto-detection. They recognize automatically to which port to connect.

  2. the benefit of a fibre on a wired ethernet are usually greater reliability (no interference with other electro magnetic fields) and the possibility to connect larger distances. If you need this or not depends on your needs.