Measurement & Automation explore (MAX) cannot find any serial ports

Similar Questions

• How to set the Date and time on a remote target in Measurement & Automation Explorer (MAX)?

  Hello

  I'm trying to follow the steps described in the following link:

  How to set the Date and time on a remote target in Measurement & Automation Explorer (MAX)?

  It is said

  The software on the target currently supports only the time zoneand deletes the old files?

  I need set the date and time

  and remove all the old unwanted files

  the calendar was gray does not allow me to change the current date.

  Anyone know how to change

  

  

  Hi all!

  According to this the below Knowledge Base article, Remote Configuration System Support must be installed on the target for time settings to change in MAX.

  http://digital.NI.com/public.nsf/allkb/FAB0EC4D6E5EE0F386257738005733A3?OpenDocument&MeTC=max_MAXDat...

  If you don't know what version of the system supported remote Configuration software that you have installed on your device target, it is likely that it is not yet installed. Add this software by clicking below your target to the MAX software option and selecting "Add/Remove Software". This is where you will install the System Configuration Remote Support software.

  Please let us know if you have any questions!

• NEITHER Measurement & Automation Explorer 5.0 (superior version already installed)

  I have downloaded the driver NOR-DAQmx 9.4, but when I try to install it I get the message:

  Cannot install

  o OR Measurement & Automation Explorer 5.0 (superior version already installed)

  What does that mean? I have LabVIEW 2012 (Windows), version 12.0, 64 bit.

  Thank you

  Neil

  I think what is happening is that DAQmx is installed correctly, but the installer also try to install an older version of Measurement & Automation Explorer (MAX), which is what causes the error.

  You can check that DAQmx has been properly installed by opening MAX and check if it is listed on the software tab on the left.

  One thing to keep in mind is that 9.4 DAQmx is not compatible with LabVIEW 2012, so you can just upgrade to the latest version of DAQmx, which is 9.6 and is compatible with LabVIEW 2012.

• installed Acrobat DC and get the error indicating the serial number is valid but cannot find any product calling on my computer

  installed Acrobat DC and get the error indicating the serial number is valid but cannot find any product calling on my computer

  As indicated, with an upgrade (apparently what you bought) you will get a request for both the new S/N in the old S/N - assuming that a qualifying product is not installed).

• Cannot open Control Panel Test VISA in Measurement & Automation Explorer

  With the help of Visa OR Measurement & Automation Explorer. Select the devices and Interfaces and select my device. The Test Visa Open Panel is grayed out and is not available. Some tools-> NI - VISA-> VISA Interactive Control, and the following error message appears-"unable to start the program because it lacks cvirte.dll form your computer." Try reinstalling the program to fix this problem. "I reinstalled the driver NI-VISA and the problem persists.

  Hi David,

  I'm glad that you solved. It could be that the library file has been installed, but that it was somehow lost and unable to be found by measurement and Automation Explorer. A massive compilation could have located this file and placed in the expected folder. I'm curious to know if you did a search system for the library file? I know you have talked about doing one for the file in the document I linked to you. Whatever it is, I'm glad that you were able to get this working.

  Have a great day!
  Jackie

• How to uninstall corrupted NI Measurement & Automation Explorer?

  Hello

  I have problem to install LabView 2012 and all components, cos does not properly uninstall my version previous (2012).

  I have LabView_Fall_2012 and NI_Device_Drivers_August2012 and Win7 x 64. (try to install it on a partition not OS).

  Now when I try to install new I get "OR Measurement & Automation Explorer 5.3 (superior version already installed)" and installation stops there.

  My goal is to set everything up if possible to properly uninstall and then reinstall it. Now I have managed to remove most of the files, reg entries and stopping services, but some things are still left.

  What can I do for that Setup to deal with?

  Its possible to remove all the files/reg manually?

  There is a file that cannot be deleted ' C:\Program Files (x 86) \National Instruments\Shared\mDNS Responder\nimdnsNSP.dll ", its possible to remove it?

  Thanks a lot for your help

  IMHO, there are two options:

  1. try to reinstall 5.4 MAX, download here

  2. the STI DLL used by the LV you update tool can remove it using this tool: Unlocker

  Stefan

• LabVIEW Measurement & Automation Explorer very slow

  Hi all

  Here is my setup of the system and the version of LAbView:

  • [LabView professional Development System - Version 11.0 - 32-bit]
  • OPERATING SYSTEM - windows 7 Home Premium 64 - bit SP1 [MS]
  • CPU - [Intel Core i7-2600 processor 3.40 GHz]
  • MEMORY - [16.0 GB RAM]
  • GPU - [NVIDIA GeForce GT 530]
  • OR PXI-7951R & NOR 5761

  Everything works absolutely fine until yesterday. All of a sudden, everything about LabView is very slow. Send commands to run the stepper motor and even check on Measurement & Automation Explorer. There have been major changes in the updates or removing software from National Instruments. Everything is intact. My antivirus is AVG (which is a recent change after I removed mcaffee, but I don't think that's maybe the reason).

  any kind of advice is appreciated.

  Thank you.

  

  Add or change your antivirus/firewall can have a major effect on LabVIEW and related products, because they can potentially block your network connections. MAX scans your network for remote devices.

  I also had a problem a while back where my Firewall blocked access to shared variables. The following instructions helped me: http://zone.ni.com/reference/en-XX/help/371361G-01/lvhowto/createditlogosxt/ (I don't think this affects the MAX, but I mention this in case you encounter a similar problem)

• problem w / measure automation explore or/o Inst Asst

  Hello

  I'm new to Labview and I work my way through the tutorial. I loaded 3 disks for measurement Automation Explorer such that I can complete getting started with Labview Ch.4, using a DAQ hardware. The part where I place an e/s of Instrument on the block diagram Wizard is taking me to the top. When I double click the sub VI, it appears an error message telling me that "measurement automation explore or e/s Instrument wizard is not installed correctly. I loaded the disc twice up to now, the same questions. No one around the Office can understand it, either. I use discs of Labview dated February 2007, NOR MAX 4.2, 3.0, NI DAQmx 8.5 compliance record. Any help is greatly appreciated. Thank you.

  Hey,.

  Try the solution that is presented in this knowledge base article.

• Toshiba Stor.e Partner - cannot find Nero serial number

  Hello

  I try to install my new partner of Toshiba Stor.e 1 TB on my Windows Vista computer and the installation, it asks me a Nero BackItUp 12 Essentials serial number to validate.

  I assumed it would be the serial number on the bottom of the HARD drive and the packaging, but it does not work. He is not on any of the leaflets that came with it and cannot find any info on the user guide.

  Anyone know what I'm missing here?
  Thank you

  If I understand your message, you have found the serial number, but it does not match with your software. Right?

  Are you sure that you have entered the number correctly?
  Perhaps you the number of faults striking or mixed numbers like 0 and o or i and l
  Check again.

  You can also upgrade the Nero software to the latest version

  How? Check out these links:
  http://APS2.toshiba-tro.de/KB0/TSB14034U0000R01.htm
  and
  http://www.Nero.com/enu/products/Nero-BackItUp/upgrade-to-Nero-BackItUp.php

• Windows cannot find any networks

  Hi all

  My dsl network connection is not discovered by vista suddenly I have tried all possible means, but to no avail any help would be greatly appreciated!

  the error message says "windows cannot find any network."

  its a DSL connected via a LAN connection

  I think I found the culprit, it turns out be a updated windows defender definition... ive stopped using my network connections now run fine LOL

• How capture and save a sequence continues to images using NI 1422 LVDS card capture, through Measurement & Automation Explorer?

  It is possible to capture and record a sequence of images with a LVDS OR 1422 EZMaker using Measurement & Automation Explorer?  Everything is installed correctly and running and I am able to use the "Snap" command to save an image, as well as the 'Grab' command, but it seems that you must stop the dump command before you can save anything, and it only allows you to save the final image.  Is there a way to record a sequence that is being caught, or should I use LabVIEW or other additional software to do this?

  Kind regards

  James S.

  Hello James,.

  You will need to LabVIEW or another environment development in order to record a sequence of images. If you have LabVIEW and the Acquisition of Vision software, you will be able to capture and save images in an AVI file. There are examples that come with the Acquisition of Vision software that can do this.

  I hope this helps.

• Windows cannot find any additional network?

  I am currently using my laptop that can connect to my home network but my PC can't. My PC can't find no additional network. It says it is connected to the network called 'Network', but I can't use my internetor all programs using the internet. It says "windows cannot find any additional network." I clicked on "Diagnose why windows cannot find any additional network", it told me to update my drivers and my drivers he's was updated. Can someone help me?

  Hello

  You can check the link below and try the advice given and check if that helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/Windows-cannot-find-any-additional-networks-an/ca9f086b-42A5-46E5-b894-92c009f8eba8

  Hope that information was useful

• Windows cannot find any networks, but Ubuntu can! (X 32 Vista Home Premium)

  I recently replaced a faulty laptop computer mother board with an identical model (only difference is a newer version of the BIOS). After restarting Windows (Vista Home Premium 32 bit) I can't find the networks wireless where I can see usually eight networks at least an unsecured connection, but now I get nothing.

  I replaced the wireless card Atheros with an Intel Pro 3945ABG driver and installed the latest version and that I still get the same error "Windows cannot find any networks", I can get access to the internet via an Ethernet cable but I am unable to connect wirelessly. If I try to manually configure the wireless connection, I get "unexpected error occurred".

  I started the system from a CD of Ubuntu to check that it was not a hardware problem. Wireless card perfectly, sees all the networks, connects and works very well.

  It seems that something inside Vista has failed since even change the wireless adapter for a different manufacturer and the results of the modeling in the same error, pointers?

  Kind regards

  Jason.

  SOLVED

  It turns out that Kaspersky Internet Security is at fault and he was very happy to work via ethernet it had mutilated all WLAN connections.

  Removal of Kaspersky and all of a sudden all the wireless networks have re-emerged.

  Kind regards
  Jason.

• Windows cannot find any additional network / an unexpected error has occurred

  I got this new PC Windows Vista Home Edition x 64 SP2 and I need to connect it to the network wireless in my house because that the router Netgear DG834GT wireless broadband is not very conveniently placed for wired connectivity. I have a Netgear WG111T USB wireless adapter which works fine on my other PC / laptop (XP & Vista, both 32-bit), but I can't make it work on my Vista x 64 PC.

  I have installed the version of the driver 2.1.0.26 x 64-compatible for the WG111T and the device works correctly, according to Device Manager.

  When I try to 'connect', I get 'Windows cannot find any additional network . " While the other PC at home can pick up 3 wireless networks.

  Go until the network & sharing Center, then manage the networks without wire, then Add, then manually create a network profile, I get "unexpected error ."

  I spoke to Netgear who insist the player WG111T is compatible with the x 64 visits.

  I talked to my PC provider who suggested to try the adapter on another PC Vista x 64 to see if it works there. Problem is, I don't know anyone else with a Vista x 64 PC.

  I would be extremely grateful if someone can help me before on this one. Thanks in advance for all advice.

  See you soon,.

  Arty-W

  It seems that the problem was caused by ZoneAlarm Internet Security Suite hinder and prevent the correct installation of the Netgear wireless driver. My problem has been cured by following the advice of daouda wire - see http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/58716eca-80cb-4555-a1f4-bd4e5350aeb4

• error message "windows cannot find any network."

  When I try to connect to my wireless network, I get an error that says "windows cannot find any network". Already called my internet provider and has been sent back to microsoft. I have a netbook at home and he search for connection to the internet, but my desktop running Windows Vista Home prem is this error message. I use microsoft MN500 as my router.

  Hello

  1 are there any changes or updates made on the computer?

  2. were you able to connect to the network before?

  Method 1:

  I suggest you to return the item and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  I suggest you to reset the TCP/IP Protocol and check if it helps.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  Method 3:

  See the link and check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233/en-us

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up the registry, (http://support.microsoft.com/kb/322756/) see link:

  Back up the registry

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry