Migrate or restore replacement device?

Similar Questions

• Source:-elxcna (adapter Emulax CNA) event ID:-129 error:-\Device\RaidPort1, restore the device, has been published.

  Hi all

  Source:-elxcna (adapter Emulax CNA)
  Event ID:-129
  Error:-\Device\RaidPort1, restore the device, has been published.
  Server:-Server Rack, Windows 2008 R2
  Installed application:-installed Backup tool and IBM tape library connected by Cisco nexus switch

  Summary:-each time the backup tool initiating any SCSI command etc. for library of tapes, just after a few minutes in the event log, server shows "restore the device, \Device\RaidPort1, has been issued." and the tape library configured in backup tool disconnected from the physical tape library.

  Up to now steps below was taken but no luck:
  1. test Unit Ready has been disabled in the registry
  2 adapter ANC, fresh of zoning has been replaced.
  3 firmware and driver from the adapter of the ANC has been updated.
  4. timeout was defined according to the guidelines of this document:- http://blogs.msdn.com/b/ntdebugging/archive/2011/05/06/understanding-storage-timeouts-and-event-129-errors.aspx

  Comment:-26 fev 12:00 Am, I put to tape library firmware update and then we got
  This 129 February 26 event id error 03:00.

  Need help? :)

  Hi SabarnaDeb,

  Thanks for posting your query in the Microsoft Community Forums.

  As the question is limited to Rack in Windows 2008 server, it is better suited for the IT Pro TechNet public. Please ask your question in the Forum on TechNet Support.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  I hope it helps. If you have any questions about Windows in the future, please let us know. We will be happy to help you.

• Omen of HP 15-5000na: \Device\RaidPort1, restore the device, has been published.

  Hello

  My computer laptop freezing from time to time for 15-20 seconds (about 8 - 9 times per hour). When the gel it is impossible to make any disc operation, that is, open the file, or start the Explorer... the disk in the Task Manager activity is 100% reading.

  The only thing I found suspicious is a message in the event viewer / newspapers Windows / system that says:

  -------------8<--------------------------

  Source storahci

  Event ID: 129

  Text is: restore the device, \Device\RaidPort1, has been published.

  -------------8<--------------------------

  I search on google for that matter. I have set up my power plan high performance with settings for "PCI Express" / link state power management 'Off' (was befor change moderate energy economy)

  But this has no effect portable stell gel.

  I have no other choice for any type of RAID in my BIOS and my HARD drive is SanDisk SD6PP4M - 256 G-1006.

  SanDisk dashboard software indicates that the SSD is O.K.

  Windows 10 updates and drivers are up to date, also I flashed the BIOS to the latest version

  Any ideas how to solve this annoying gel are welcome, I will try all of them.

  Kind regards

  spetrov

  Hi go2.

  Thank you very much for the detailed information.

  I installed the hp support assistant and this software updated my drivers for more later you mentioned in you post.

  I can't find how to rebuild my raid (which I don't have) in the Intel Rapid technology software, there are only a few options awailable in this software and none of them can be used to rebuild the raid.

  However, I managed to solve this problem with the activation of additional options for power plan settings for hard drive

  named "AHCI Link Power Management - HIPM/DIPM" registry and then, after that the options are visible in the settings of the power plan, set options for DIPM (HIPM is not taken in charge of my hard drive).

  This link provides information how to activate this option of additional hard drive in the power plan settings and how to change them.

  http://www.SevenForums.com/tutorials/177819-AHCI-link-power-management-enable-hipm-DIPM.html

  Best regards, spetrov

• \Device\RaidPort0, restore the device, has been published. Event ID: 129 storahci

  Hello

  I have a DELL XPS 13 9343.
  I did a clean install of Windows 10 and downloaded the drivers from dell.com.
  I am also running Hyper-V.
  I'm repeated warnings in my saying system Envent Viewer:

  \Device\RaidPort0, restore the device, has been published.
  Source: storahci

  Just before I get these events my computer freeze for 10-20 seconds and I can´t anything.
  It's very annoying, and I hope there is a fix for this?
  Thanks in advance.

  I had exactly the same problem on a lot of my dell systems. Here is how I solved the problem:

  First we need to change ""AHCI Link Power Management " which is a setting hidden in power management." Open the registry editor and change the following settings.

  HKLM\SYSTEM\CurrentControlSet\Control\Power\PowerSettings\0012ee47-9041-4b5d-9b77-535fba8b1442\0b2d69d7-A2A1-449c-9680-f91c70521c60

  Change 1 to 2 attributes

  HKLM\SYSTEM\CurrentControlSet\Control\Power\PowerSettings\0012ee47-9041-4b5d-9b77-535fba8b1442\dab60367-53fe-4FBC-825e-521d069d2456

  And again change the attributes of 1 to 2.

  Now, go to the Control Panel-> system and security control-> Power Options , click on "Change Plan settings" and then click on "change power avancΘs."

  Now under "Hard disk", you should have AHCI Link Power Management - HIPM/DIPM and AHCI Link Power Management - Adaptive options.

  
  Change the 'AHCI Link power management' active, meaning that there is no AHCI power management and finally change adaptive to 0 milliseconds (well if you have enabled "active" this option has no effect).

  Finally under "PCI Express" change "Link State Power management" to OFF.

  I hope this will help you.

  Good luck!

• Migration of es300 to device of esVMWARE

  Good afternoon.  We're upgrading a hard appliance to SonicWALL es300 virtual messaging security appliance.  I have the AV installed on our network of LABORATORIES currently.  A problem is that to restore all the settings/names must match and we are unable to do it on the laboratory.  I did a complete to the top of the production apparatus, then went through each entry (Yes, it was as much fun as it sounds) and changed the names/parameters so that it would correspond to the LAB name and parameters.

  However, after I restored the settings, Junk box, archives, reports, the only thing that seems imported are dictionaries.  There is no date in the archives, no junk mail box or no report parameter info or settings imported.  More importantly, there are no filters.

  I guess if I have to, I can do without the parameters, but I would really like to be able to import existing filters that we have configured.  We have a lot of complex filters long this link in another unit of ORGANIZATION and dictionaries to allow different users send or receive various e-mail or attachments.

  Does anyone have any ideas on how I can get the filters and if possible the undesirable elements, the archives and the report and settings migrate to the new appliance.

  Thank you!

  Hi Dean,

  The all must have the host name even in order to import the backup files.

  If it's just the strategy filters that are not displayed, it seems the file may be damaged. (it probably can be fixed)

  I open a Web folder and attach a copy of your backup and ask if a technician can review explaining the same information you have here.

  There are a lot of files inside backups that contain information about the host name and if not the same may not be present.

  Would have been the right way to get the operational VM with no parameters of first.

  If you can then rename the old device, after getting backups (each article separately) from the user interface, then rename your VM to match the old appliance as well as the IP address if possible. (IP is not necessary).

  Once it is up and the correct name import your backup settings and the other one at a time, separately.

• Migration of VCS (VM device)

  Hello

  Is there an easy way to migrate a virtual machine configuration of a device from VCS?  You can restore from a backup of the device?

  I know how to migrate the licenses already, but I'm not sure of the configuration itself.  I would really prefer to do it by hand if possible.

  Thank you.

  You can use the backup/restore feature VCS located under the maintenance menu to copy your data and configuration from one server to another.  See the section "Backing Up and Restoring Data VCS" VCS administration Guide on page 296.  Remember to take note of the restrictions, such as the two servers must run the same version of software and contain the same option buttons, among other things to note.

  Furthermore, according your original description, it sounds as if you have already purchased the necessary references (R-VMVCS-C-M-K9 or R-VMVCS-E-M-K9) migration for new licenses of virtual VCS, if not, refer to this thread: vcsvcse-license-migration-material-vm.

• Choose to restore the device on itunes or the device?

  I don't know where the box restore or update will appear!

  Please you can rewrite your question because I do not understand. You try to restore your iPad?

  Marco

  UPDATE: just saw the Summit. You forgot your password. Connect your iPad to your PC and then click on restore in iTunes. You may need to put your iPad into DFU mode well. To do that follow these steps:

  • Connect your device to your computer with a USB cable.
  • Turn off the device.
  • Hold the Power button for 3 seconds.
  • Hold the Home and Power buttons for 10 seconds.
  • Release the Power button but keep holding the Home button.
  • After that 15 seconds, you will be alerted by iTunes saying that it has detected a device in Recovery Mode.

• OpenWapp migration to a new device?

  Is it possible to go from the OpenWapp with all contacts and messages from my my flame Keon?

  I learned by watching his source code, OpenWapp seems to use IndexedDB for storage of conversations.

  Using backup_restore_profile.sh, I finally found a way, and I wrote a little HOWTO.

  Migration of the Keon (1.3) to a flame (2.0) seems to work. I write "seems" because I see the messages migrated fine, but I can't connect to WhatsApp for now: OpenWapp registration process has been broken for a few days. Perhaps WhatsApp changed its API.

  Note that simply return the Keon on the flame settings did not work and in fact crashed the device (restart required).

• How to restore a device which was accidentally removed from the list of media sharing

  I accidentally deleted from my list of multimedia sharing device, how can I restore this unit?

  Hello, ERP,.

  Are what device you referring?

  Stop, unplug, turn on, plug?

  Have you tried a system restore to a date and time when the unit has been included?

  What is the system restore

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  Share your multimedia files
  http://Windows.Microsoft.com/en-us/Windows-XP/help/Windows-Media-Player/11/share-media

  Sharing media on a network using Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows-Vista/sharing-media-on-a-network-using-Windows-Media-Player

  Change settings for sharing media in Windows Media Player

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-settings-for-sharing-media-in-Windows-Media-Player

• Can galleries of DPC lost in Migration be restored?

  Hello

  I have spent countless hours searching and selecting image comps for possible review. These were carefully furnished according to Gallery of Dollarphotoclub, alias bright tables. Without FAQ information or alerts, I assumed that custom galleries would transfer on Adobe stock. I wish desperately galleries can be restored - my clients and I have invested a lot of time and effort. The loss is devastating. Help, please!

  Craig

  Hi Craig

  It is covered in the FAQ Dollar Photo Club - Dollar Club Photo - photo galleries free high quality royalty and vectors - Club picture Dollar

  Will be my galleries and download history be transferred to Adobe Stock?

  No, it is not possible to migrate your galleries or your download history for Adobe Stock.

  After migration, the account of the CPD is closed and there is no option to restore, I'm afraid.

  Kind regards

  Bev

• ICloud will remove my photos if I restore my device?

  I have had some problems with my iPhone and you want to wipe it and then restore a backup iTunes to see if it was a software problem. All my photos from my iPhone are stored in iCloud and I fear that if I wipe my iPhone, pictures of the aura disappeared. Can someone give some advice?

  As long as you sign in settings/iCloud with the same Apple ID and make sure that the sync settings are correct, they must charge on the iPhone.

• Camcorder JVC Windows says vista and XP ' device unrecognized try another usb port if it doesn't have a replacement device.

  Model of camcorder JVC GZ-MG50AA

  computors on XP sp3 and Vista laptop. Both give the same message when the camera connected to download videos and pictures.

  Hi Davo1957,

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: You can try to connect the device to a different USB port and check if the problem persists.

  Method 2: There are chances that the USB cable may be defective. You can check the device connection through different threads.

  Method 3: You can run the Microsoft Fixit from the following link and check if the problem persists.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

   

  Method 4: You can follow the steps in the Microsoft Knowledge Base article and check.

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  http://support.Microsoft.com/kb/871233

   

  Method 5: Install the drivers updated and chipset for the device and check the results. You can see the article mentioned for more information below:

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Let us know if that helps.

• How to restore the devices with removable storage "missing icons

  HelloW sir This is krivy! for some time more I'm months local disk G not displaying don't not its icon (devices with removable storage) totally absent I m so depressed about this because I m unable to put my pen-drive & usb Cables & having so much work to the system that has information in the key USB sir could you tell me a solution for this problem

  Hi krivy,.
   
  Method 1: Check if the drive is visible in disk management.
   
  a. right click on my computer > Manage > Disk Management > right click on the removable storage drive and select Change drive letter > select a new drive letter not already in use.
   
  See if that helps.
   

  Method 2: Run the troubleshooter from the link given below and if that helps.

  Hardware devices not detected or does not

• Factory restore the device?

  Hey there,

  Is there a way to restore/reformat a disk iXpand to its factory state/settings? I use a Mac/iPad.

  Thank you.

  the iXPand is really just a normal flash drive. There is no parameters which can be restored. In the application of the IXpand in car, you can clear the cache, but that's really all.

  You can also put the iXpand to erase all content using a computer. If you have a mac, you will need to format to exFAT or file MS-DOS (FAT) systems and you will need to make sure you use the MBR (Master Boot Record) for the partition type. If you have a windows computer, that you can format with the default settings.

• I forgot my administrator password. How do I restore my device?

  Hello, I forgot my administrator password and I couldn't access my account and if I download something using the guest account, there need varification when you log in to the administrator account. How can I reset the administrator account, or change the password. I have an urgent need to use my camera. Pls help!

  Thank you

  Kathleen

  Hello! Kates, don't worry.