monitor AOC, will not work when I start my Dell desktop, getting just lights flashing green computer

Similar Questions

• keyboard does not work when you start. Unable to get to the bios screen.

  When I reboot to get to the bios screen my keyboard does become functional until windows load. I don't remember what is a problem in the past, but since I disconnected everything recently I was wondering if it happens to be a USB port which remains hot during startup.  I have a Gigabyte motherboard.

  Thanks for all the help.  I found a port that remained hot during startup.  Not an easy feat because there are 6 USB ports on my MB.  Then after may restart to finally find, I remembered that I have also 2 USB ports on my Dell monitor that remain hot even when the computer is off.  A lesson I will never forget.

• Keyboard does not work when I start windows

  my keyboard does not work when I boot my laptop.   When I do any changes inside through properties keybord (even the spped blinking cursor) he started working. but when I press capslock, it stops working again and I have to still to change the settings in the keyboard properties to make work.i have tried to install the new software, I got my laptop to format but it still does not.

  need help with this and please tell me the solution if r there all

  If by "I got my laptop to format", you mean you have reinstalled Windows and the problem persists, it is probably a hardware problem. If you have a keyboard that can be plugged into your laptop, there the same problem?

• Satellite A200 28H: F6 floppy will not work when installing XP

  Hello

  I am trying to install Windows XP pro on my new laptop (Satellite A200 28 H), and since it needs driver SATA, I downloaded the driver suitable for my laptop (Satellite A200 28 H), put it on a floppy disk for use with a USB floppy drive (which works fine), press "F6" when appropriate and everything... But it simply doesn't. I had training as a technician for a few years, so even thouh that is no longer my work and I might be a little rusty, I think I still know at least a little what I do... Well, apparently I'm more image than I thought!

  I've tried several things, and this is what I get:

  * If I don't use all the disks, Windows XP will not find the hard drive. Which was intended, no problems here, don't except for the fact that it is completely useless for me :)

  * If I force the driver on the floppy disk, despite Windows tells me that is already a driver that can be used, then within 10 seconds I get a BSOD with the stop message 0x7B (found or inaccessible boot device).

  * If I use the floppy drive, but do not force the driver and listen instead of Windows ("oh, you already have a driver? ("OK, then, use and too bad that diskette"), I can actually finish the installation process. Windows will copy all the necessary files on the disk, it will even restart correctly after that and moved on. But when the installation is complete, the computer will restart, I'll see the loading for a second screen, and then, BSOD stop 0x7B again.

  I'm sure I downloaded the driver for my computer. In fact, I also tried a couple of bad drivers too, just to be safe (IE I use Intel Matrix for ICH8M, but I also tried the ICH7M to be sure), I tried with drivers downloaded from the Toshiba site, on the site of Intel and whatnot-other-website-for-newbies-or-powerusers, and I still have the same behavior as described above.

  I tried partitioning / formatting during installation, and I also tried leaving the file system intact. If I do the latter, the only difference is that I have offered 2 possible OS to boot from, the two being Windows XP and both failed miserably.

  It's probably worth mentioning that, if I use the recovery DVDs and start over and clean with Vista, I have no problem whatsoever, except for the loaded gazillion process during startup, the RAM already used half and applications useless hundred I don't give a darn on... And the fact that some applications that I need work just can not be installed on Vista.

  If anyone has any idea how to solve this problem, I would be very grateful!

  Hello

  The procedure, including the SATA drivers in Win XP using the external USB floppy drive is very easy.
  First you need to download the Storage Manager and having to put on the diskette.

  During the installation of Win XP you must press F6 for inclusion since the external floppy drive and follow the new instructions on the screen.

  _Note; _
  Very important is that your XP CD Win would contains SP2!
  Without SP2 a BSOD can appears and could break up of installation!

  Don t format or don t create all partitions after the installation of the SATA driver. It can erase the installed and included from HARD disk SATA driver.

  Last but not least some readers of external floppy drive are not supported. I read that some users had some problems with an external FDD drives they tested another drive and it worked finally

  Check the recommendations may indicate that it might be useful

  Good bye

• Windows Update fails to install KB2539636, KB2468871, KB2533523. Will not work when installing manually or the other.

  I tried to make these updates manually, but they don't always work. I run Windows Vista 32-bit. Despite receiving an error message when installing updates via Windows Update or manually, when I go to the stop, the icon to install the updates always appears next to the stop button. I click to install updates day and then stop, but when I start my computer again the icon is still there, which indicates that they have not installed correctly.

  Manually update an error message of "> Code update here< does="" not="" apply,="" or="" is="" blocked="" by="" another="" condition="" on="" your="" computer.''="" is="">

  When trying to update by using Windows Update, it seems that everything is going as it should (the update is downloaded, it is made a point of restoration etc.) but after they have finished installing, I get an error message in the sense of "updates not installed correctly. An unknown error has occurred. ».

  This is the first problem I had with the Windows updates. Can anyone help?

  Thank you very much

  Nathan.

  Some people have reported that manually download and install updates succeeded in fact.

  Updates:

  1. http://www.microsoft.com/download/en/details.aspx?displaylang=en&id=27017 (KB2539636)
  2. http://www.microsoft.com/download/en/details.aspx?id=3556 (KB2468871)
  3. http://www.microsoft.com/download/en/details.aspx?id=27014 (KB2533523)

  Make sure you download the one appropriate for your system.

  http://support.Microsoft.com/kb/827218 (ie X 86 32-bit =)

  Install as administrator.

• My explorer.exe will not respond when I start my laptop and my entire desktop computer eventually white

  My laptop worked fine when I turned it off for the night, and when I come back to use it the next day, that windows Explorer has stopped working when I turn on my computer. My whole office is empty, including my wallpaper and I can not enter in 'my computer' and 'my documents '. The Task Manager works and I can run iexplore.exe and other programs.
  Here are the details of the problem
  Signature of the problem:
  Problem event name: InPageCoFire
  Error state code: c000009c
  Type of media loopholes: 00000003
  Name of the damaged file: explorer.exe
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1042
  Additional information 1: 559f
  More information 2: 02934d2c52b3f39550891518a9d15746
  3 more information: 6ef5
  Additional information 4: b5d88008fbc27fee13f30131eedf2314

  I run on Windows vista 64-bit

  Hi shellysong, I suggest you follow troubleshooting steps from the method below. Method 1

  Step 1

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2

  I recommend you perform the clean boot.

  See the link below to learn more about how to clean boot.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  Click Start, type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or for confirmation, type your password, or click continue.
  On the general tab, click the Normal startup option, and then click OK.
  When you are prompted to restart the computer, click restart.

  Method 2

   

  Try the SFC scan on the computer.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

• description interface LabVIEW node will not work when compiling

  Hello

  I have a vi that seeks VISA resources and focuses on their name of the interface to select that you connect to.

  I have a strange problem where, if I run the vi in labview it works fine. When the vi is compiled into an exe file, it does not work.

  I traced the problem to the property node "name of Inst Intf' which gives the description of the interface. In Labview, the node of this property returns the description of the interface, as expected.

  When I compile the vi, this node property returns empty strings.

  The station nearest you, that I could find to this kind of problem is it

  http://forums.NI.com/T5/instrument-control-GPIB-serial/why-visa-property-interface-information-inter...

  However, the exe is running as an administrator, so I don't think it's a problem with permissions.

  Any help would be greatly appreciated.

  I have no idea of what was the cause, but I uninstalled the device drivers for the hardware I used, reinstalled and then restarted the computer and now it works fine.

• computer Dell laptop will not work when using battery

  Original title: my pc dell 1564 model. Act when I remove the battery (with adapter only), but when I fix the battery, it is not turn on

  my pc dell 1564 model. Act when I remove the battery (with adapter only), but when I fix the battery, it is not turn on

  Hello

  It is best to get the laptop battery checked from Dell or a local technician. It seems that the battery is dead and does not load when you insert it into the laptop.

  However, you can try to update all drivers installed on the laptop (including the motherboard) and check if it makes a difference.

  http://Windows.Microsoft.com/en-in/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Navigate through the common troubleshooting steps of http://www.dell.com/support/troubleshooting/us/en/04/KCS/KcsArticles/ArticleView?c=us&l=en&s=bsd&docid=266588

  http://FTP.Dell.com/DIAGS/R66243.htm

  Hope this information helps. If you have any questions, please let us know.

• iPhone 5 s microphone will not work when recording video with back camera.its a noise

  My dear engineers

  I had a 5 s 16 GB iPhone. now, I can't record video because it's one a kind of noise but video quality better .What do to this problem.

  IOS 9.2

  Thank you

  Try latest iOS update

  If the problem is still there your microphone near the rear camera does not work properly so best to take it to the repair by Apple Store

• Will not work HP TouchSmart 15-j078ca n ENVY: fingerprint - no lights reader...

  Hello

  Since the replacement of hard disk and reinstall all my fingerprint reader used to light up.

  HP TouchSmart PC ENVY 15-j078ca laptop

  Update driver,

  simplepass update software

  BIOS shows biometric not like option, thinking about this issue perhaps?

  Cannot use HP to check and update because it seems to not be able to rip off my laptop once its identified it!

  Thank you

  @BCBuddy

  The "Scan my PC" program may not work for you, no, I do not know exactly why; Suffice it to say if the program does not scan your PC to find your drivers / support page, you can perform the operation manually, that is, access your computer Support pages.

  Computer:

  HP TouchSmart PC ENVY 15-j078ca laptop

  A few ideas

  There is not a Windows 10 associates BIOS update for your laptop.  I doubt, there is nothing to change (in BIOS), except if you need get the BIOS to default because it has been changed at some point.

  In some weird cases, BIOMETRICS must be enabled in Windows 10; It is primarily a problem unless something hinky, AND you run Windows 10 Pro.  The document below covers a little of this - ignore the idea for now.

  There is not a Windows Validity Sensor 10 / fingerprints Synaptics driver.  The listed pilot is evaluated for Windows 8.1 and should suffice or Windows 10.

  File name: sp63418.exe

• A new Mac (2015). Migrated CS4 products. They will not work even after reinstalling Adobe download. Get error messages.

  Open question cannot be resolved: #.

  0215673548

  Errors with photoshop: some of the missing components. Replace. (I have 3 times without resolution).

  HAVE: Missing fatal error. and error of Plugins.

  Dreamweaver: Could not locate resources file... reinstall. (It's-no not fixed.)

  Finally got Adobe Pro to work after the 2nd re-installation.

  You should probably uninstall and use the cleaning tool before you try to reinstall - it might be useful.  Migration does not work for Adobe products if so doing, he might have left a bit of a mess behind.

  Adobe Creative Suite cleanup tool

  helps resolve installation for CS3 thru CS6 and creative cloud problems

  http://www.Adobe.com/support/contact/cscleanertool.html

• bookmarks and other tools will not work when you click on

  nothing happens when I click on the items on the bar including the bookmarks tool. If I restart the program sometimes it will work for awhile.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the startup window Mode without failure.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Help! in bulk license photoshop 7.0 with Cs3 upgrade will not work when reinstalling - Adobe support cannot help

  I have installed/reinstalled CS3 (upgrade on Photoshop7) a few times since 2007, when I updated my pc - since the first installation, I had to contact their Aussie number 1800 because the Photoshop disc was a version of license in bulk and he didn't like the key when CS3 audited upgrade.  Spent more than an hour today on a chat with Adobe and they will help me more is that they are not trained on PS 7 or CS3.  ANY HELP would be appreciated

  If your products are registered with Adobe, they can unlock CS3. It's called a "challenge code".

  Apparently, Adobe has a coding challenge system.  So, if you have the old serial number of the upgrade and you call customer service.  The customer support has a challenge code procedure where they give you a code that overrides the problem.  Unfortunately, it took me 5 calls to customer support until I found someone who was able to do.  The keyword is "Challenge Code"

  Error "this serial number is not for a product calling it" | CS6, CS5.5, CS5

  Important:  We can unlock your serial number after that we first check that you are eligible for the upgrade. When you contact us, be at your computer to complete the following upgrade verification workflow.

  1. Register your product.

  2. Contact us. You will complete the next steps with a staff member.

  3. Do one of the following methods in the screen upgrade serial number :

     • Windows: Press Ctrl+SHIFT and double-click it.
     • Mac OS: Press command+SHIFT and double-click it.

     The Code upgrade window appears.

  4. Read the challenge Code to support staff member.

     Enter the support Code (which provides Support Adobe) in the field support Code and then click Next.

  Gene

• My windows live mail will not work when my dsl is connected to my router, but when I connect it to my computer, it works fine. Why is this?

  Belkin router

  Hello

  • This happens only Windows live mail?
  You can connect the DSL router and then try to use internet with a browser and visit some websites.
   
  If this only happens with Windows Live mail then it will be better suited in the Windows Live Forum. Click on the link below.
  Windows Live Solution Center
  http://www.windowslivehelp.com/product.aspx?ProductID=15
   

• Task Manager Windows 'show all processes from all users' will not work

  Hi im running service of 64 bit vista Home premium pack 2

  For some reason any button "show all processes from all users" in the Task Manager will not work, when I click nothing happens, uac prompt little or nothing.

  I can end processes very do well no problem it's just the show all button that does not work, I thought that maybe the taskmgr.exe in my right-click system32 folder and compatiability tab and running it as admin it would work, but the compatiability tab is completely grayed out all I can't click anything in it.

  Im not a big computer wiz, but I checked my user accounts account im logged on says that it is the administrator and UAC is on.

  On a side note do not know if this has nothing to do with my problem but recently my computer has got contracted a Trojan horse that has infected the mrt.exe file, I had to delete, now I get an error during windows startup associated with mrt.exe works not properly. any suggestions how to solve this problem too

  Hello

  Make sure that the malware is removed completely

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  _____________________________________________________________________

  also run the sfc/scannow command.

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally madeprograms,Accessories, right-clickguest, and then clickrun as administrator. If you are prompted for an administrator password or a confirmation, type the password, or clickallow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions

  How to analyze the entries in the log file generating the program Checker (SFC.exe) resources of Microsoft Windows in Windows Vista

  http://support.Microsoft.com/kb/928228#appliesTo

  If SFC detects the main problems it can't fix you may need to borrow a Microsoft dvd vista not an acer, HP etc. recovery disk and do a repair installation

  read the below tutorial on how to perform a repair installation

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html