Monitor (Suspecting software, no hardware isssue) IMG

Similar Questions

• The UPGRADE software and hardware Mac

  I always use the InD CS2 on a G4, running 10.4.11 (Tiger), using a 22blueIV LaCie monitor. Considering an upgrade, but have read on this forum of incompatibility of CS4 and Snow Leopard. Have to wait a while until that software is no longer compatible?

  Also to wonder about a Mac Pro or iMac, use mainly InD and PS.

  All comments and suggestions appreciated regarding software and hardware.

  What budget do you have?

  As for the CS4/Snow Leopard, nothing major thing I've seen.

  Bob

• MacBook air 13 "has no forcetouch? It is a software or hardware built-in to the force click on features?

  MacBook air 13 "has no forcetouch? It is a software or hardware built-in to the force click on features?

  The MacBook has ForceTouch by http://www.apple.com/macbook/specs/

  Force the touch trackpad for precise cursor control and pressure detection capabilities; allows strength clicks, accelerators, drawing sensitive to pressure and Multi Touch gestures

  but the current MacBook Air does not by http://www.apple.com/macbook-air/specs.html

  • Multi-Touch trackpad for precise cursor control; supports inertial scrolling, turn, enter, three‑finger by sweeping, sweeping four fingers, tap, double-tap and drag

  It requires integrated hardware.

• How can I make sure that any firewalls (versions of software or hardware) does not block port 443 to access?

  How can I make sure that any firewalls (versions of software or hardware) does not block port 443 to access?

  Hi Anna_753,

  Usually, you would receive messages from any program if it is impossible to access the port.

  If you want to check if the port is accessible, then you will need to check the firewall settings.

  Each firewall has its own parameters for ports of the computer.

• Could not load the library dill for new software and hardware.

  That's what my software told that goes with my own material. I can't it ends to the bottom of the load.  I close my antivirus to down load.    (deleted) Call me if you want.   Could not load dill liibrary C:\Docume~1\user\Local~\1temp\GLF6.tmp can I use my driver recovery cd and not lose the documents on my computer?  What can I do to get my new software and hardware to work?

  Hi RonaldAndis,

  ·         You try to install a software?

  ·         What software are you trying to install?

  ·         Is it a downloaded software or you have an installation CD?

  Method 1: If this is a downloaded software, then try to download it again and see if it helps.

  Method 2: Search for damage if you try to install using a disc.

  Method 3: Place the computer in a clean boot state to install the program.

  How to configure Windows XP to start in a "clean boot" State

  Note: Make sure that you put the computer to a Normal startup, once the troubleshooting completed.

• Whenever I try to evaluate and improve the performance of the computer, I get a type of white blue screen telling me I have bad software or hardware and my computer does climb?

  Whenever I try to evaluate and improve the performance of the computer, I get a type of white blue screen telling me I have bad software or hardware and my computer does climb? He did NOT finish the task is content to any screen blue screen saying it's bad it's bad, your computer is messed up bigtime, so-to-speak

  Hi Cynthia,.

  1 have you ever done any hardware or software changes to the PC?

  2. What is the brand and model of the PC?

  3. What is the full error you get when you try to evaluate the computer?

  Audit of the statues of the device in the Device Manager.
  a. click the Start button, type devmgmt.msc and press ENTER.
  b. check for any exclaimation mark and the status of the devices.

  Follow these methods.

  I suggest you to first run the resolution of performance problems.

  Method 1: Open the resolution of Performance problems
  http://Windows.Microsoft.com/en-in/Windows7/open-the-performance-Troubleshooter

  Method 2: Disconnect non-essential external devices and try to evaluate the computer.

  Method 3:  Also, temporarily disable the antivirus and check the question.  Anti-virus programs are sometimes called causes this problem.

  Turn off the Antivirus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Let us know if it helps. If the problem persists, please answer, we will be happy to help you.

• Black monitor and remains black - hardware or software issue?

  
  

  I have already suggested you.

  I never had to install a driver of monitor, video projector (Spotlight presentation), HDTV or LCD display. LCD screens are sometimes delivered with driver discs, but the views are also not Plug Play devices. This is why the operating system recognizes and installs the drivers as required.

  The following image is a screenshot of this desktop PC Device Manager. It has two screens connected as you can see. I haven't installed any drivers. Try uninstalling the driver to see what effect it a. let the OS do its job.

  

• Satellite A100 - configuration of the monitor without software

  I need help!

  I almost tried to configure my monitor, but I don't understand.
  I am a passionate photographer, that's why I need to make a configuration of my monitor to get best results when my photos are printed.

  Does anyone know how to change the color and contrast of my monitor?
  I know there is some kind of software to make it easier, but I don't have the money to purchase some.

  Is there no alternative to the configuration without any type of software?

  Thanks a lot for your help! :-)

  Hello

  I do not know what Satellite A100 you exactly and what graphics card is integrated, but please check advanced display settings. There you can find different settings and also with the color settings tab.

• My printing problem is related to software or hardware?

  This is an important distinction to make because, in general, they require two different courses of action.  You can save yourself a lot of time ensuring that you know what type of problem you are having.  Investigation on the front can allow you to focus on the exact problem.

  A printer that stops printing from the computer of treatment might have a hardware or software problem.  Software problems when a printer is not physically able to print will not lead to success.

  The order is important?

  Yes.  Any time, you cannot print, you must exclude the material first.  If you decide that you have the hardware and software problems, you must correct the firsthardware problem.

  How do you decide?

  Typical examples of hardware problems:

  • The printer (ordered the printer) status report or a photocopy out empty, low or poor quality.
  • Printer does not respond when trying to photocopy
  • Printer recognizes photocopy request, but no paper is pulled into the printer.
  • In general paper jams.  Sometimes, an update of the firmware can help them.
  • Unable to send a fax directly from the printer.
  • Some colors on paper, but not others.
  • Problems with the ADF Document (CAD) of the power supply.  Sometimes, an update of the firmware can help them.
  • Default alignment.

  Examples of software problems:

  • Unable to send a print job to the printer from the computer, but a copy can be made.
  • Impossible to send a fax from the computer, but a fax can be sent directly from the printer.
  • Can not sweep, but can make a photocopy.

  Solution provided

• Limitation of 200GB SDHC - this is a software or hardware limitation?

  I picked up a good deal of a recently SDHC card that works well for me - this is a card of 128GB.

  From the same provider, I can also get a card of 512 GB for a similar price.

  Issues related to the:

  (1) the limit of 200 GB on SDHC cards is a physical limitation or a software limitation? Are there opportunities for a future update to bring us beyond 200 GB on the Z5 range?

  (2) if the Z5 can't handle the 512 GB, that should be the case now, it would be possible to format such a card to 200 GB?

  See you soon.

  Hi @chrisdbarnett,

  Welcome to the community.

  As I understand it, the limitation is a combination of the two. On the software side of things the WBS format has limits, and on the hardware side, the devices have limited processing power and RAM.

  If you insert a 512 GB SD card in the Z5, theoretically (I have not personally tested) it should always be able to access the card, however, you will not be able to store more than 200 GB.

  Although it is possible to increase the theoretical limit with a firmware update, it is highly unlikely that it will do more that probably cause some performance issues with the phone.

• Migration of the iscsi initiator software to hardware initiator on 2012 Hyper-v cluster.

  Hello

  We have 10 blades x M620 with Broadcom 10gig 57810 M1000e CMC card dedicated for iSCSI Equallogic PS 6110 San.

  Currently software used on cluster hyper-v Windows 2012 connect SAN PS6110 iscsi initiator.

  150 VMS are in production on 15 CSVs.

  We want to change the initiator of the software to the hardware on all our existing blades without CSV output.

  Is it possible on hyper-v cluster 2012 to have 5 blades with initiator software and remaining 5 blades with hardware initiator with same CSV cluster?

  If coexistence of initiator software and material as possible through hosting then I can apply this change a bit on our 10 blades without cluster downtime.

  Hello

  What version of FW EQL do you use?

  Yes, it is possible, however a couple of updates warn first.

  1.) install the latest firmware / boot code and driver for Broadcom cards.

  2.) put the node into maint mode then you can disconnect the SW iSCSI provenance and sign in using the HW iSCSI adapter.

  3.) do not try to do it with an active node / online.

  The advantage of the HW iSCSI adapter reduces the CPU Overload, if you are maxing out the CPU not now, do not expect a large increase in performance after HW iSCSI card.

  Kind regards

• "Application cannot be started. Contact the application provider' but I have the right software and hardware.

  Windows 8.1

  THAT IS TO SAY 11

  XPS 8700

  Get several times, "Application cannot be started.  Contact the application provider.  I recorded and also tried to open it from the site.  I always run as administrator.

  The application is malware or is not certified WHQL.  64-bit versions of windows DO NOT ALLOW any application or driver or hardware to run or install if they are not certified WHQL.

  This is not the dell software and not supported here.

• Calibrator, LCD display, software and hardware... need to recommendation (s)...

  Back to photography when CRTs were the only monitors... I know that this is extremely important and want to be fully compatible with Adobe.  Please advise...

  You want to ask advice on what type of computer and the monitor to buy?

  Most of the machines in the average range (costing around $300 +) made today must be able to manage of Photoshop Elements.

  For reference, this page is the required system configuration. They are the bare minimum required from a computer for Photoshop Elements run. Today most of the new machines would meet these specifications.

• How read a file WPS that was created by processing, what software or hardware do I need to be able to read it, it was sent to me by email

  tried to open it with adobe reader, it did not work and now when I download it again he keeps trying to open it with adobe reader, he was sent to me by email

  Its format of MS Works document
  You may be able to open it with MS Word, otherwise tell the sender to send you the file in plain text format
  It tries to open in the player, because when you've got the popup asking you are looking for a program to open it you had the "always use" check box checked, you must now reset your file associations for "wps".

• A virus attack my software and hardware

  I received a phone call from someone who said that they represented "Microsoft", asking me to give them access to my PC. they gave me with a command (eventvwr) that showed that I had a virus, can someone please explain how to use the microsoft product support to rid my PC of this contamination.

  It is a SCAM and FAKE for sure.

  I suggest you take a look at:

  http://cyberdefend.WordPress.com/2010/05/14/Hello-i-am-from-Microsoft/

  If you think you are infected by the Virus and then try to run a full scan with:

  http://OneCare.live.com/site/en-us/Center/whatsnew.htm