Multiple Configuration LAG switch

Similar Questions

• Configure the switch to WAP

  I have a demonstration kit that includes a WLC 2106 and WAP 2 1252. I have configured the WLC correctly (I think) and the WAP 2 can contact the WLC when they are plugged directly into the WLC and I can connect my wireless laptop. I want to spend the WAP directly connected to the WLC to a core switch Cisco 3560 G. No one knows what port on the 3560 settings should do or where I can look. I have configured the switch ports:

  Interface GigabitEthernetX / X

  switchport trunk encapsulation dot1q

  switchport trunk allowed vlan 212,214,215,901

  switchport mode trunk

  but when I plug in it do not access the WLC.

  Happy, it was a simple problem to solve :)

• KVM access - needed to configure the switch upstream?

  I'm short on time, and I'll put up a UCS solution tomorrow for the first time. I have a feeling I'll have problems of access to the console KVM IP subnet.

  Do I need to configure the switch upstream so that the KVM access to the work of the management of VLANS? The subnet KVM stands by the management subnet. I could also set to the same subnet. What is practice here?

  KVM IP subnet must be in the same subnet as the management IP addresses you assign to each fabric interconnect. This is due to the KVM using the versus network ports the FEX upstream to FI ports.

  Hope this helped...

  Richard Pugh

• SG200-08 Configuration LAG and Internet access

  I have what is probably a very simple and completely the question of noob, but after hours and days of research, I can't quite understand.

  I have the switch SG200-08 that I use for the aggregation of connection between a NAS Synology DS713 + and my HP Z820 workstation.

  I have ports 1 and 2 set up as LAG CH1 connection to ports 7 and 8 as LAG CH2 connect to the NAS and HP. I'm AT & T Uverse as my Internet provider so I have a single cable from my Uverse router to the switch Cisco to provide Internet access. I also am coming out of my Cisco switch on my Apple Airport Extreme, offering a Wi - Fi connection at home, in addition to access wireless to the NAS.

  I have no problem to see and connect to my NAS drive, but my problems comes with regular internet access to my computer.

  I created a team with two of my Intel NIC and connect properly to the NAS. My Internet is, however, completely hit or miss.

  A few times, it shows Internet access and connects to the web pages very well and other times he will say: no Internet. I tried dragging around ports, enable/disable some settings that I have either read online thinking that it might be one of my problems, but at this point all this COMPUTER jargon made my brain bleed. I don't know if my basic settings are correct or if I need to change something simple to get this to work all this. I have attached a basic outline to help understand my confusion. Not sure if it is my bad configured switch. It could also be my team of SHIFT created in Windows 8. Hope I've provided enough information.

  

  Thanks for any advice.

  Kind regards

  Toby

  Hello

  I had a similar problem with a workstation running Windows 7 and 8 by using a network card Intel 350 - T2 with a grouping of LAG interface.

  As soon as I DISABLED FRAMES JUMBO on network cards, the questions is arrested and everything worked fine (ping always successful, the Web pages showing all applications).

  Hope this helps for you also.

  B.r.

  Sven

• IviSwitch loses value when sending, "configure the switch" configuration = TRUE

  Hi all

  We are currently assessing Teststand 4.1 with a multimeter keithley 3706 switch system.

  After a first enthusiasm, thinking this tool with the meter switch fits perfectly our needs, real life seems difficult.

  Between several other problems, we must say to the device, the channel "s1com1" and "s1com2" are strings of configuration.

  Configure the teststand step: change the switch step IVI-> IVI, switching, configuration switch: channels "s1com1" Configuration = True

  led to observable in both actions in Ni Spy:

  GetAttributeViBoolean (..., "s1com1", _IS_CONFIGURATION_CHANNEL, VI_FALSE)

  SetAttributeViBoolean (..., "s1com1", _IS_CONFIGURATION_CHANNEL, VI_FALSE)

  manually call to this function of the interactive a CVI fp class works as expected (the VI_TRUE updated)

  Is there any hint that we could do wrong? Currently, we are just before writing wrappers in cvi and jump all the wonderful Types of IVIStep in teststand.

  Looking forward to any comments

  David Clus

  David-

  This would have the same problem we discovered recently in our internal tests. For the problem that we found, we will probably include our fix in a next corrective patch. You can check if the problem persists if you change your locale in English in the control panel? If the problem no longer occurs, can you use this as a workaround for now?

• I can't HP printer works again. Configuration, driver, switch print or USB port does not.

  I got the printer doesn't work after downloading the update and the usefulness of HP. They were put in a folder of Tamp, I think.  New utility and install HP downloads don't work this time. In addition, cat pulled the printer USB cable and I don't know where it was connected to. Message Windows XP says out connection or something about switch printing don't no configuration?  I don't understand any of this, can someone ' a please talk me through it? I have a lot of work piled up, legal and medical stuff and really need my printer.

  Hello

  What is the model number of your printer?

  It is sufficient to indicate the complete error message you receive.

  
  Method 1: you can refer to the documentation that came with the printer for printer connections. You can check the following HP link

  http://www.HP.com/United-States/consumer/everyday-printing/Wireless/USB-wireless-setupb.html

  
  Method 2: you can see the steps outlined in the article below to solve printer Windows XP problems

  Resources for the resolution of the printer in Windows XP problems

  http://support.Microsoft.com/kb/308028

• Configure MXL switches blade for active paths using 2 Qty ANC

  Dear members,

  I need to configure a solution in which 2 CNAs Qlogic 57810 s was used to LOM & port B of each server blade m630, converged switches in A1A2 B1B2 & cracks MXL. All switches have under the IO modules mentioned:

  • Ports SFP + 10 GbE Module 4 port replaceable hot 4 x SFP + (optical or direct attach cables)
  • Fiber Channel Flex Module e/s, with 4xDell, networking, transceiver, SFP +, CF, 150M, SW, FIN

  Here are the requirements of the customer

  • Battery A1A2
  • Battery B1B2
  • All roads for SAN i/o Flex modules & LAN of SFP + must be active asset for a redundancy level CNA. attached is a diagram for a better understanding.
  • All empty ports of each switch blade ends at the DMZ switch with SFP + converter RJ45 1GBE customer.

  I know how to stack together A1A2 & B1B2 spend together, I need to know what needs to be set at the level of the CNA to support active active connections/paths. In addition, A1A2 & B1B2 switches to support IO END & Flex for convergence n/w infra.

  Your plan sounds great if there is any VLAN.

• vNetwork Standard Configuration of switch

  Hello

  We have 3 guests ESXi 5.0.

  I configured the network as below that we have only 4 NICs per host;

  All the IPS below are in a VLAN. And what a vlan is configured on a physical switch.

  ESXi 5.0

  vSwitch0

  The VM network

  Networking - same vlan ip

  VMkernel_vMotion - same vlan ip

  2 NICs (active/active)

  vSwitch1

  VMkernal_iSCSI - same ip vlan (our IP storage is a different subnet, but it can communicate with the ip subnet of vlan.) This is when the creation of this port, there is no option to 'check' designed to 'storage', then how iSCSI traffic will pass through this port ONLY?

  2 NICs (active/active)

  I want to know if this configuration is ok?

  OR

  Suggest me a better option than this.

  Thank you

  Mihir

  Easy answer. You don't assign it a gateway to VMkernel iSCSI ports. If you use IP addresses in the same subnet as the storage system, you don't need a gateway. VMware does not support iSCSI traffic routed anyway.

  Now that you have found a VLAN / subnet dedicated to iSCSI traffic, I suggest you research a little more, maybe you are lucky enough to find a dedicated VLAN / subnet for vMotion too.

  André

• Best configuration of switch for 4 natachasery - 5 ESXi

  So, I need to tell my boys to network how I want the configuration of ports (Cisco switches) for 4 natachasery connection to my HP DL 360. I need the vSwitch VM access to 3 different VLAN. I'm NOT going to use vMotion for this.

  I guess, I see 2 possibilities and does not entirely undesrstand pros / cons...

  First of all, I thought I would split the enet to 2 separate switches cables, but I was told that if I chose that this channel of ports 1 route would be active and 2nd would be Eve. Basically can not paste all 4 cards and divide them. This could reduce the bandwidth, but give me a redundancy using 2 physical switches.

  Or I can have all 4 enet cables go to the same switch (etherchannel), but if this switch would die I'm dead in the water, AND I think that EtherChannel mode WE (my network guy preferred LACP) should stay and LACP cannot be used. According... http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 1004048 I think I should also use 'Hash IP' if EtherChannel is used.

  So what is the advantage or disadvantages of each channel? Thank you!

  This article describes the aggregation of ESX/ESXi links:

  • ESX/ESXi host only supports grouping NETWORK adapters on a single physical switch or stacked switches.
  • Aggregation of links is never supported on disparate networks switches.
  • The switch must be set to perform 802.3ad aggregation of links in static mode WE and the virtual switch must have its defined route based on the IP hashload balancing method.  Ensure that participants of the network adapters are connected to the ports configured on the same physical switch.
  • Allowing each route based on the IP hash without 802.3ad aggregation or vice versa disrupts networking, so you must make the changes to the virtual switch first. In this way, the service console is not available, but the physical switch management interface is, so you can activate the aggregation on the affected ports to restore network.
  • For more information on ESX networking concepts, see the VMware Virtual Networking Concepts.
  • For more information on configuring a VLAN for NIC teaming, see Configuration of VLAN Virtual Switch, switch physical and virtual machines (1003806).
  • To set up the consolidation of NETWORK cards on ESX and a physical switch, see example configuration of EtherChannel / link aggregation with ESX/ESXi and Cisco/HP switches (1004048).
  • The only option for switch vSwitch or vDistributed that can be used with balancing EtherChannel is HASH IP.
  • Do not use tag with IP HASH load balancing.
  • Do not uplinks configure standby or not well obliterated with IP HASH load balancing.
  • VMware takes support only a single Etherchannel by vSwitch or distributed vNetwork (vDS).

  heybuzzzz wrote:

  In my case with no vMotion and just management and 3 VLAN all about 1 vSwitch I should put them all to active?

  Yes, they should all be active, there is really no need passive adapters (that I'm aware of your configuration).

  On your physical switches, you don't need to do anything more than what allows a VLAN correct, i.e.: should all etherchannel or a similar montage. Side vSwitch, you must use the default 'Port ID' nic teaming strategy.

• Configuration of switch qsfp force 10 MXL

  Can someone send the link to the qsfp ports configuration. The documents I have are not specific on how to specify that Im using cable A. thank you

  the port number of the 40GbE QSFP + ports in the tracking module, Base: 33 or 37; OPTM

  SLOT 0: 41 or 45; OPTM SLOT 01:49 or 53.

  You can view the status of the interface with the following command.

  # display the status of the interfaces

  This will identify the ports. Then use the following command to access the interface.

  (conf) #interface fortyGigE 0/33

  Let us know if you have any other questions.

• BlackBerry devices with multiple phones of switching software

  I currently use two devices BlackBerry, the Z10 for labor and the Z30 for personal use. I've done a switch of the device of a curve (previous working device) for the Z10 using Blackberry link. I recently bought the Z30 and want to make a switch of the device to my old torch for the Z30. Is it possible to do so using the same link BlackBerry program? Only, I have a PC and want to know if I get a headache trying to do or if there is a better solution.

  Thanks for any help!

  I have not ran into problems because I use two different BlackBerry ID so I had to sign without a job and then sign in to my personal account. Thank you both for your good help.

• Multiple audio stream switching in Win7/WMP12

  Hello.

  I have a bunch of home movies I took with a 1394 camera and recorded on the PC.  I have used DivX to compress these films and my wife overlay a second audio track of Chinese for Grammy can watch movies.

  Previously, I used WMP 9 to play movies and used Morgan Stream Switcher to allow audio to pass (it was quite a thing to learn at the Grammy Awards to right-click).

  Now with Win7 and WMP12, I don't know how to change the audio stream.  Reading, two audio streams are superimposed and I hear Chinese and English both at the same time.   I googled around the internet and binged this site and do not have too much success, just stuff of DirectX, but nothing useful.  It seems that Morgan stopped supporting its flow selector in WMP10, so I don't know if it works or not, or is now by WMPv12 there is finally an embedded solution.  There is another shark codecs pack that seems to resolve the issue, so this may be a limitation of codec in Win7/DirectX/Wmp12.

  We'd appreciate clues.

  Hi DumasaRock,
  
  There are several third party plugins to tour the market. You may need to search for a third-party plugin using your favorite search engine and support for the codec to go with it because there is no embedded solution to Windows Media Player 12 on this issue.
   
  Just as there was Morgan Stream Switcher to allow the passage of audio streams in Windows Media Player 9 with Windows XP, I'm sure there will be a third-party plugin for this one as well.
   
  NOT MS. LINK:
  Important note: this response contains a reference to third party World Wide Web site. Microsoft provides this information as a convenience to you. Microsoft does not control these sites and no has not tested any software or information found on these sites; Therefore, Microsoft cannot make any approach to quality, security or the ability of a software or information that are there. There are the dangers inherent in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet.
  
  See also:
   
  WMPlugins.com : http://windows.microsoft.com/en-US/windows/downloads/wmplugins
   
  Codecs: Frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/codecs-frequently-asked-questions

  Aziz Nadeem - Microsoft Support

• How to configure the switch for JMS bridge

  Hello
  
  I tried with the selector option when working with several bridges, here is the scenario that I applied.
  
  Created five queues ( Q1, Q2, Q3, Q4, and Q5 ) and configured JMS bridge Destinations with each queue with the factory of unique connections ( CF1, CF2, CF3, CF4, and CF5 ) and baptized as D1, D2, D3, D4 and D5.
  Then created JMS JB2 bridges with D1 source and destination as D2. Similarly the JB3 as D1-D3, as D1-D4 JB4 and JB5 as D1-D5.
  And sector for each of the JB2 JB3 and JB4 JB5 as two, three, four and five respectively and reboot after the changes.
  
  Now I expect the following scenario to work
  By pushing the message to Q1/CF1 with two in the content of the message, so wait for the message to be delivered to Q2/CF2 through JB2, but messages is not moved by JB2.
  Similarly, message pushed to Q1/CF1 having three in the content of the message, so waiting for the message to be delivered to Q3/CF3 by JB3, but messages is not moved through JB3. Similar behavior for other messages with four and five in the content of the message.
  
  In the bridge configuration, selected QOS as "Atmost" - once.
  
  Note: all configurations were conducted in the same field and the WL version is 10.3.6.0 *
  
  The example message I am pushing to Q1/CF1 say 'two Test Data'* and expect to reach the queue Q2/CF2
  
  Concerning
  Venkata Madhu
  
  Published by: vv * Sep 12, 2012 13:05

  JMS selectors work normally om jms headers and not on the message.

  In my previous post, I see that WebLogic provides an extension "SELECTOR xpath" in this area, although I recommend using standard selectors when possible. See my previous post for more information on the syntax of the selector, etc.. The best resource on selectors is the javadoc for javax.jms.Message (http://docs.oracle.com/javaee/5/api/javax/jms/Message.html).

• Multiple Configuration Oracle question

  We have a typical environment configuration. I'll explain below:
  
  Our application works Online and Offline Mode. For the online mode, connect us to the Enterprise Server Oracle 10 g and a local instance of access and the offline application works totally in Access.
  
  Now, we want to move away access and have PE Oracle rather simply because we want to use the stored procedure and even all of the code for the treatment of offline and online.
  
  Thus, a typical user's machine will be an instance of PE and an Oracle Client. Currently, we use LDAP.ora for setting up connections. Now, I have a few questions
  
  1. How do you ensure that Oracle PE will work when we have no network connection. Can we have like installation of PE with Tnsnames.ORA
  2. what may be the smallest possible package for PE.
  3. can I use a client to access the databases and PE.
  
  Any help will be much appreciated.
  
  Thanks in advance.

  Assuming that the "Xcopy install" refers to the use of the Windows xcopy command, you can specify what, exactly, you install via xcopy? You are simply use the xcopy command to copy the ODP.Net bits? Or you try to install the Oracle client with this approach?

  If you are concerned about support, you generally want to install everything through the Oracle Universal Installer (except the very occasional components that do not use the YES). Oracle supports usually only software installed via the installer, because particularly on Windows, there are a number of registry entries must be created.

  You can certainly do a custom installation of the personal edition on end-user machines. There are a few prerequisites that must be installed according to me (who will take care of the Installer). I guess that your customization will take the form of a response to the YES file, to do a silent install?

  Justin

• multiple control for switch case structure

  I have four process past... my first process is supposed to work for 12 hours and next three deal for 1 hour each. Since I have many variable to display I use tab control. Now my question is how use two controls for the case selector one based on the tab control where the user can see the second and individual process parameters based on time where the process should be automated according to the time it's when 12 elapsed hours that the second process continues to the next process 1 HR even 3rd and 4th. can someone help me please

  I enclose my vi

  This?