My battery icon is flashing blue to Orange quickly even if the computer is connected to the power supply

Similar Questions

• Satellite A500 - battery light flashes when connected to the power supply

  Win 7 Satellite A500 PSAM3A-03P00E.

  Battery light flashes when connected to the power supply (intermittent fault), when I disconnect the sector and reconnect the flashing stops and battery (high capacity) continues to receive.

  Also, when battery light blinks the keyboard backlight stays on when it should white and if the backlight is turned off and the battery light starts to blink the keyboard backlight turns on, all other functions seem to work well.

  Charges of battery and the wedges load properly (when the battery flashes).

  Hello

  Have you noticed this problem since the first day of purchase?
  Theoretically, it could be possible that your battery begins to malfunction
  On the other hand, an electrical problem could also be possible

  However, try this:
  Remove the battery and the AC adapter. Then press and hold button power 30 sec long.
  Then insert the battery and plug AC adapter still does that help?

  By the way: this is the BIOS updated? If this isn't the case, perform an update.

• Pavillion G7 1263-nr: HP Pavillion G7 led beside the power supply plug flashes 3 times... does not illuminate?

  Unit does not illuminate. When the Start button / stop is pressed with power cord only or with the battery and the power cord or battery only I get 3 flashes of the white LED on the side of the unit next to the power supply.

  I replaced the receiver taken power in the change of unit No.....

  I used an other (workin) power cord and adapter... no change.

  I tried another battery (work)... no change.

  I pulled the two memory chips don't... no change.

  I put the two don't chip memory in one at a time... no change!

  I'm out of solutions short of replacement motherboard which is not profitable unless I want to take a chance on a reduced opportunity to the Board of Directors.

  Only the indication of all this work are three white flashes of LED is located just next to which DC adapter/cable plugs?

  Any other suggestions/diagnosis would be appreciated.

  Thank you!

  I had to contact HP and according to them the power port led flashes 3 times after pressing the power on button, indicates a failure of the motherboard and requires a replacement.

• Have HP Pavilion dv2500, won, t turn on. When you connect the power supply blinks blue.

  Have HP Pavilion laptop dv2500, p/n kn997ua #aba, does not illuminate. When you connect the power supply blinks blue.

  Now you can take the laptop at best buy or Wal-Mart and get them to plug a power cord. This will give you an idea if you need to buy a power cord or not.

  Again, you can always buy the power supply cord and if it does not return.

  THX

• Spectrum X 360 (N1W02PA #UUF): best practices for the use of the power supply battery for laptop (spectrum X 360)

  Hello.

  I know the best practice to use the power supply to charge the battery? I heard that keep charging your battery while using Notepad deteriorate autonomy. I don't know if that's true, but I do not charge my spectrum X 360 at 20% power level.

  Kindly need some expert advice. Thank you.

  Hello:

  My recommendation is to follow the instructions provided in this document from HP to address... paying particular attention to the info listed according to the recommended battery care practices.

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=c00596784

• System fails to recognize the power supply and will not charge the battery

  Had motherboard replaced but, before that, I had tried a secondary power to check if my principal could be faulty.  Card mother equipped now and all working fine except that I can't get the sytem to recognize my main diet.  Battery won't charge and the system stops if I remove the power supply.  This is on a DELL XPS M1530 laptop.

  Thanks for all the ideas.

  Hello

  Motherboard might not be properly installed or has problems - easy to miss a rider or
  any other connection as well.

  Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
  eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
  them and be careful). Batteries are old, or it could be a problem with the computer.
  Check with the support of the machine system, and many of them have on line forums.

  New Lithium-Ion type battery usually last longer if you do not unload then less than 30%
  However on a laptop that not extend their life a lot. Best is to use the a/c adapter
  When this is possible.

  I use the free version of BatteryBar to monitor my battery. Click on the green button on the
  Yellow box on the right side of the page to download the latest stable version.

  BatteryBar - free version available
  http://osirisdevelopment.com/BatteryBar/index.html

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  You can also check with the manufacturer of system and forums that many use their own
  proprietary software to monitor the battery and they could be known problems with your battery.

  ============================================================

  Try this - to make a Restore Point

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Then Control Panel - Device Manager - Batteries - Double click on each item - tab drivers - update drivers
  (who can not do anything) - then do a right click and UNINSTALL-REBOOT which will refresh the driver
  Stacks.

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Satellite M105-S3074 - blue light flashes when the power supply cord plugged

  I have a Satellite M105-S3074 that when I plug in the power cord the blue left flashes just light and unit will not feed. When I unplug it from the laptop all lights go out and it is will not help here please

  Thank you

  Hello

  This means that your mobile doesn t boot with AC/DC adapter and AC/DC adapter too?
  Really strange what s

  Have you tried to remove the battery and the AC adapter? If you remove the two you should an hour and then reconnect the two. Maybe it will work.

  If this isn't the case, it seems to be a hardware problem. You must contact an authorized service provider, you can give them a call to speak to a technician.

• Tecra 9100 blue screen when you disconnect the power supply

  Hi people,

  Im having a major problem, Ive had a major problem with my tecra 9100, when I unplug the power cable and try to use the laptop on battery, the blue screen comes up saying NMI: channel check / IOCHK

  then the computer shuts down, it restarts only properley if I plugged power of ext,
  also something to note, when I unplug everything first, he's not str8, its only when I try to use the laptop, which is pressing a key

  If someone knows something about this could you please let me know

  Thanks carl

  Hello

  This has been already discussed here in the forum:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=13784

  Check the sanremo poster, which refers to the knowledge base article Microsoft!

• HP Pavilion DV7 laptop: Touchpad, sometimes active, even when the power button is pressed on off (light orange)

  I use a wireless mouse (or a wired mouse) preferably instead of the touchpad.   The touchpad has a power button to press - white light indicates on and off Orange light.    After booting, I usually disable the touchpad and mouse wireless, however, sometimes when you type I realize my palms are contacting the touchpad and the cursor jumps around accordingly.    The touchpad is disabled (orange light) but I can control it with a finger, it works like its supposed to as if it is enabled.     Any ideas?   I have not downloaded a driver updated or do anything to try to solve this problem, as I fear, it could actually cause other problems.

  Update the driver it is the usual Council for problems - that is the solution here?   Has anyone else had a similar problem.    Most of the touch pad problems I've read is in regards to an erratic touchpad - nothing to do with 'on' or 'off' problems.

  HI @WayneCM,

  Thank you for your inquiry. I will do my best to help you!

  I understand that you use the power button / stop to turn off the touchpad.  Sometimes, you will notice that your palm is in contact with it and the cursor is accordingly jump around but the rest light orange, to show that he has disabled.  Here is a link for HP Notebook PCs - using the touchpad and ClickPad (Windows 10). Please review the section on "Open the properties of the ClickPad" in figure 4, you'll see there's a button where you can disable the touchpad, until you want to reactivate it. Please let me know if this helped.

  Thank you! If it helps you to find a solution, please click the button "accept as Solution" down below in this message. If you want to say 'Thank you' to my effort to help, click on ' Thumbs Up ' to give me a Kudos.

• Satellite A200: Should I remove the battery when working on the power supply

  Hello

  I've been running an A200 machine for the last 2 months, bought as a desktop replacement in order to fit in my small apartment. I realize now that I never ued work on battery - it is always powered on sector. Since this is unlikely to change, should I remove the battery? Deing battery degrades remaining in the machine while it is continusouly by the industry feeding, or does it not matter?

  Thank you very much in advance for your reviews.

  GW.

  You can remove it, but it should not be done. For me, it's stupid to remove the battery and let the dust make the battery place dirty. The batteries we use today are very good and Scott wrote the electronic power supply just to check if the battery is full and care the battery and the battery capacity.

• Portege R500 works on battery, but after connection to the power supply is OFF

  Hello

  Problem I happened suddenly, laptop computer workins perfect all the time, but since yesterday when I plug the laptop ac adapter will work for 10 seconds off powerd then and then lights - just the orange power cord icon flashes.
  I checked the AC with my girlfriend protected r500 adapter - it has exactly the same model and its working perfect on HQ..., when I use the battery of my laptop works again correctly - any ideas

  You can start your Portege with only (removed battery) AC power?
  If yes it and when Windows is fully charged battery back in place.

  What happens when you do this?

• MBP - green flashing light on the power supply

  Hello

  I've seen a few posts similar to this one. On my 2009 MBP adapter has a flashing green light and won't turn on. All of the suggestions I've seen seem to suggest removing the battery for 30 seconds or so before putting it back in. I tried this with no luck, too--I always get the same problem without the battery. If I thought that the battery was the culprit I would buy a replacement but as I still have the question without the thing I think that it is something else.

  Could someone point me towards any suggestions please?

  Kind regards

  Matt

  I think this article can deal with your situation.

  On the battery LEDs on MacBook Pro and MacBook (13-inch, aluminum, Late 2008) (Late 2008 and later) - App...

• what it means if the power LED flashes red, that I am plugged into the power outlet

  help what is a flashing red light on average power

  Yes, the batteries in laptops are like any other rechargeable battery, they have a life cycle. Since the bits of information so far, it sounds as if you do not want to replace the battery. You can see what is essentially a stack to the page linked below:

  How to replace your laptop battery
   http://www.Dummies.com/how-to/content/how-to-replace-your-laptop-battery.html

  What I would say has visited support site for the manufacturer of your laptop; using your specific model name/number search for laptops support page. You should be able to get some type of documentation that will explain the flashing red light. Also get the specifications for the battery of your specific model (see technical data). Though on checking support site for the manufacturer to see if they have their own forums, if so you may be able to find details about the light, and what is involved in the specific battery in your laptop.

  Computer manufacturers
   http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  Kind regards

• iPhone 4S heating quickly, turn off the power and the battery drains quickly.

  Hello

  My problem is exactly the same as the title. My iPhone 4S warms up quickly, turn it off and after I turn the iPhone, the battery drains quickly and the iPhone will turn off after 5 minutes. iPhone turns off again and again until I put the iPhone on the charger. It is bad because I like to play games like Pokémon GO. But after 10 minutes of play, the iPhone starts heating (and of course delay).

  Things I've tried: (and didn't work)

  The apps I use no fence. (I close applications once I stop playing)

  Turn off location Services. (Enabled only when I'm with apps like GPS...)

  Reduce the brightness

  I will be grateful for any kind of help.

  Welcome to Apple Support communities, Krystof11cze.

  It seems that you encounter problems with your iPhone 4S on iOS 9.2.1 with heating, battery draining and stopping. Good job on the steps you tried as I would have recommended those as well. I will do my best to help!

  1. backup of your iOS device - because I have erase you your iPhone completely, it is strongly recommended that you will lose your data if you do not.

  2. restore your device to factory settings - using the settings on your iPhone will only erase your personal data. You will need to let iTunes erase the iOS version installed a new clean copy can take place.

  3 test the question - the first time through, set up your iPhone as a new iPhone when it asks. It's just temporary. You can connect to iTunes and App Store and iCloud and also download some of your applications. Test for problems you encounter. If your iPhone's battery life is improved, follow the next step.

  4. restore your iPhone, iPad or iPod touch from a backup

  Take care!

• Adobe Flash Player does not not even once the download installation is completed

  I tried to go on several Web sites and content display - Youtube, lazy and some websites I need for educational purposes. When I try to view the contacts or download a song, I get a message saying that I need the latest version of Adobe Flash Player to do so. I have lived this process several times today, but each time I have download Adobe Flash Player, it tells me that the installation is complete. However, I am still unable to see the content or listen to the songs. I have restarted my computer several times and that didn't work. I see that the Flashplay is listed on my Add / Remove programs in the Control Panel, but it does not when I enter these sites. I called tech support a couple of times today with no resolution to my problem. Please HELP! What can I do? Thank you

  Hi td, I do not know what OS you are using or the version of the browser, so I'll just make a guess :-)

  With IE, go to tools > Manage Add ons and find the Shockwave Flash object... ActiveX control... Flash10d.ocx and make sure it's there and activated.

  If the FF, go to plugins and see that the SWF, vs 10.0.42.34 is listed and enabled.

  Also, go to add/remove and check the versions and lists of Java and post this info back. YouTube uses the latest version of Flash Player and the latest version of Java (which since yesterday is JRE 6 update 18)

  Thank you

  eidnolb