My bubbles screensaver lights. I am running Windows 7, IE8.

Similar Questions

• Running Windows XP - SP3. Power light flashes and the fan motor is running but no video to monitor input

  Original title: MY PC has CRASHED or?  Windows XP - SP3

  Running Windows XP - SP3.  Power light is flashing and the fan motor is running but no video input for monitor and no power to the keyboard.  I tried another monitor, but still no video input.  I wonder if the motherboard went wrong or what happened.  Thanks for any help.  Pat J

  Hello

  Since there is no power for the keyboard and monitor, the issue seems to be with the material. I suggest that get you in touch with the hardware manufacturer for further assistance on the issue.

• Too bright light on the screen of Portege 3440CT (running Windows 2000)

  Hello

  Do you know how to reduce the brightness on the screen of the laptop Portege 3440CT running Windows 2000?

  I have another question about the 3440CT Portege battery: battery charge never, I can't solve the problem, I left the power supply 8 days but battery levy at all! I had the same problem with a second battery?

  Any ideas?

  Kind regards
  Jerome

  Hi jnessi,

  as far as I know, you can change the brightness of the P3440 with the key Fn and F2! Agic otherwise your settings in the tool!

  If two batteries are as old as the portege, it may be that this batteries are too old!
  Otherwise your electronic of power supply is damaged, but I do not! ;-)

  Good bye

• bubbles screensaver refuses to change or be removed?

  Hello

  Go to settings of screen saver control--> lower panel down which gives me options to switch between the screen savers is grayed out and cannot be clicked... so I'm stuck with bubbles and I really don't like... I want to remove the bubbles... Infact I don't want all the screensaver and I don't seem to be able to do... Help, please!

  I have problems with my PC freezing at the start of my SS bubbles.  I can't change the settings, and everytime I try, my PC freezes.   I tried your suggestion but when I open the "Windows" folder, there is a folder "Office".

  I am at a loss and begging to become very bored with this problem. I run Windows Vista Edition Home Premium. If there is anything you can do to help, I'd appreciate it.

  Thank you

  JamesMcElyea, this may or may not help your post was a while ago, but maybe it will help someone else or can point you in the right direction since I am on Windows 7.  These are the instructions how to disable the screen saver

  Beginning

  Control Panel

  Appearance & personalization

  Customization

  Change screen saver

  Screen saver drop-down arrow

  Choose "none".

  Hit apply and ok

  or the quickest way:

  Click Start

  Type "Screensaver".

  Change screen saver

  Then continue with the instructions in bold above.

  Hope this helps someone

• HP Envy 23 all-in-one. : HP Envy 23 all in a single C030. Blank Screen, power light, the fan runs.

  HP Envy 23 all in a single C030. Blank Screen, power light, the fan runs. After that I opened start legacy and power cord from my puss. Help me please.

  Hi there @ZiECloNE,

  Welcome to the Forums of HP Support!  I understand that you are no longer able to boot your computer after a "event for pets.  I'm happy to help you with this.

  Don't forget to check all of your connections, power cord, power adapter, and maybe try another outlet and a direct connection to wall.  If there is no change then the following test: desktop HP - computer starts not (Windows 10.8)

  Please let me know if it works for you and if it does not solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

• The desire to have identical screens 'connect' for both computers, both running Windows XP, SP3.

  I have two desktop computers, one running Windows XP Professional, SP3 and the other running Windows XP Home Edition, SP3. When I connect the computer professional, it passes through the boot info, then on the screen of Microsoft Windows XP with horizontally lights flashing and then having to display all users who said "to begin, click your user name." However, on the computer of the publishing house, he crosses the start screen, the screen of Microsoft Windows XP with horizontally lights flashing, but goes to a screen titled "Windows Journal" and asks for my username and password.

  What should I do to get the computer to the Publishing House to display the same "to begin, click your user name" with user names like the professional instead of the "newspapers Windows screen?"

  Thanks in advance for your help.

  zeredward

  First, go to control panel > user accounts, and then make sure the "Use the home screen" checkbox is checked. OK your way out.  See http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/ua_logon_at_welcome_page_w.mspx?mfr=true
  If the box is already checked, see this--> http://www.kellys-korner-xp.com/xp_wel_screen.htm (scroll down to "the logon Welcome screen does not appear").

  If still no joy and you have ZoneAlarm or another "security suite", see June 1, 2010 post here--> http://answers.microsoft.com/en-us/windows/forum/windows_xp-desktop/windows-xp-doesn' t-show-the-welcome-screen/e5c5af46-2839-47f3-b3d3-30e55ee74a1f?msgId=b7e70ce8-474c-42c7-a851-a68b5871aaaa

• "The website has encountered a problem and cannot display the page you are trying to see." error when I try to run windows update

  I am re - install XP on an SSD. The installation went well, but when I try to run windows update, I get the following error message: "the site has encountered a problem and cannot display the page you are trying to view. I reformatted the drive and re-installed windows many links - no luck, I get the same error message. Old disk HARD charge with the SME XP install updates to drive very well. Help please!

  See if the article sheds some light for this problem: http://support.microsoft.com/kb/836941

• Run windows explore version 4.0.1377.1 on xp

  Is it possible to run Windows Explorer (from NT 4.0) version4.0.1377.1 on Windows XP.  Personally, I prefer this version. Its light weight and didn't use any form of integration with Internet Explorer. If someone could help with this, I would appreciate it.

  This is not supported.

• Why my bubbles screensaver so fast?

  Why my bubbles screensaver so fast?    OS is Vista Home Premium 32-bit with sp2.  After the screen saver has been for a time is just speeds reaching almost a blur.  Hope you can help.  Thank you

  Hello JoyceBud,

  ·         This happens after the strong activity on the computer or periodically?

  I suggest to create a new Standard user account and check.

  Create a user account

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  If the problem does not persist in the new user account, it could indicate that your old user account is corrupted.

  The below mentioned link and follow the steps to repair the corrupted user profile:

  Difficulty of a corrupted user profile

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Let us know the results.

• I've had my laptop for a year, and it is currently running Windows 7 Professional. I recently had a problem that causes the black screen

  I've had my laptop for a year, and it is currently running Windows 7 Professional. I recently had a problem that causes the black screen randomly with the screen turned on (I mean everything is black and I can't see a thing, but can still see the light of the LCD screen). This often happens when I open/close a window, browsers web example, the records, or even during the boot. I want to know how to solve this problem and if the upgrade to Windows 10 works for her.

  Hi Haolin,

  Thanks for posting your query in Microsoft Community.

  I do not understand that the screen goes black randomly, and I'll be happy to answer your query. Let me ask you;

  • What is the brand and model of the computer?
  • Remember to no particular change in the computer before the show?
  • When was the last time it worked?

  Video card problems are the most common cause of this problem.

  Try the following troubleshooting procedures in the order. If the steps described in the first procedure does not resolve the problem, continue to the next procedure.

  Step 1: Reinstall your video driver

  1. Right click on the bar tasks and then click Start Task Manager.

  2. Click on the processes tab, click explorer.exe, and then click end process.

  3. Click file, and then click new task (run).

  4. In the text box open, type explorer.exe, and then click OK.

  5. Click on the Start button , go into the Device Manager in the start search box, and then, in the search results, click on the peripheral Manager.

  6. Double-click on display the cards, right click the display device, click Update driver software, and then follow the steps in the wizard that appears. You can also visit the website of the manufacturer of the computer support and install the latest available graphics cards for the same model of computer you have.

  Note: After the driver is re-installed, you may need to restart your computer to complete the installation. You may also need to adjust the resolution of the display to its previous value. For more information, see change your screen resolution.

  Step 2: Search for registry problems

  1. Right click on the bar tasks and then click Start Task Manager.

  2. Click on the processes tab, click explorer.exe, and then click end process.

  3. Click fileand then click new task (run)

     In the text box open, type explorer.exe, and then click OK.

  4. Click on the Start button , type regedit in the search box, and then, in the search results, click on regedit.exe.

  5. Navigate to the following registry key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  6. Click to select the WinLogon key and then in the right pane, click on Shell. The value of shell in the data column must be explorer.exe. If the value of Shell is not explorer.exe, double-click Shell, and then, in the value data text box, type explorer.exe, and then click OK.

  7. Close the registry editor and restart your PC.

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: How to back up and restore the registry in Windows

  If this procedure resolves the issue, you are finished. If this is not the case, proceed to the next set of steps.

  Step 3: Start the computer in safe mode and run system restore

  1. Click on the Start button , click the arrow next to Shut Down, and then click restart.

  2. Do one of the following:

     • If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

     • If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  3. In the Advanced Boot Options screen, use the arrow keys to select Safe Mode, and then press enter.

  4. Log your computer with a user account with administrator rights. When your computer is in safe mode, you will see marked Safe Mode in the corners of your screen.

  5. Click on the Start button , type "System Restore" in the search box, click System Restore, and then click Next. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  6. Choose a restore point when your PC worked as expected, click Next, and then click Finish.

  7. Restart your computer normally.

  Important: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  If these steps resolve the issue, you are finished. If not, try to repeat the steps and chooses an older restore point (if available). If that does not resolve the problem, contact your computer manufacturer or the technical support for further assistance.

• Cannot print from FSX w/acceleration, no further questions. Running Windows 7 64 bit.

  I have FSX w/acceleration installed for a few years now on my HP G71 dual core laptop and it works great, that I had no problem at all. It was my first attempt to print from it however. I wanted to print a flight plan, click on the "print" button and nothing happened. I went to the Panel, open Printers and devices, and my printer was there, online and ready without papers pending. I went to properties and even printed a test page, so I know that the issue is not with the printer. For some reason any FSX does not send the document to the printer. How can I remedy, which should look and where? Thank you in advance for any light that can be shared.

  The duplicate thread information:

  Cannot print from FSX w/acceleration, no further questions. Running Windows 7 64 bit.

  I have FSX w/acceleration installed for a few years now on my HP G71 dual core laptop and it works great, that I had no problem at all. It was my first attempt to print from it however. I wanted to print a flight plan, click on the "print" button and nothing happened. I went to the Panel, open Printers and devices, and my printer was there, online and ready without papers pending. I went to properties and even printed a test page, so I know that the issue is not with the printer. For some reason any FSX does not send the document to the printer. How can I remedy, which should look and where? Thank you in advance for any light that can be shared.

  Hello

  The question you have posted is related to games for Microsoft Flight Simulator X and it would be better suited to the community of players for Windows.

  Please visit the links below to find a community that will provide the support you want for better assistance.

  Games for Windows:

  http://forums.Xbox.com/GFW/default.aspx

  http://forums.Xbox.com/GFW/games_discussion/pc_games_e-k/f/295.aspx

  Support of Microsoft Flight Simulator:

  http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx

  I hope that the information above helps you.

• Nine computer running Windows 8-2 accidents in the first day

  Hello world

  Any help with this problem would be greatly appreciated :)
  Yesterday, I bought a new computer running Windows 8. I use the computer mainly for photo editing, so this morning, I installed my copy of Photoshop CS4 on the computer and needed to install an update to the ACR, I downloaded Adobe.
  The first accident occurred that I tried to download the update (Camera Raw 5.7). It is this crash .dmp file - https://skydrive.live.com/redir?resid=B50D32B2D4102B3F! 187 & authkey =! AHogu8RLIx59Nt4&ithint=file%2c.dmp
  After the reboot, I finished the download of the update, installed and made sure Photoshop was working properly, that it was.
  The second incident took place tonight (Photoshop is not running, no download in progress etc..) It is this crash .dmp file - https://skydrive.live.com/redir?resid=B50D32B2D4102B3F! 188 & authkey =! AJ97jn-_skkL03Y&ithint=file%2c.dmp
  Of course, since this is a brand new computer, I don't expect to be planted at this rate. I assume that the installation of Photoshop or the ACR update caused a few problems (even though nothing I've read has suggested that it should).
  Can someone get any light it? Thanks in advance!

  Hello

  You are going through the exact same thing a user treats here - http://answers.microsoft.com/en-us/windows/forum/windows_8-performance/windows-8-crashes-after-entering-sleep-mode/b140bccd-29ae-414b-840c-ed5269c26ea0

  The attached files of the DMP are bug check ACPI_BIOS_ERROR (a5) .

  This bug check indicates that the BIOS Advanced Configuration and Power Interface (ACPI) computer is not fully compliant with the ACPI specification.

  Error checking A5, {1000, 0, 80001000, 25}

  1000 = ACPI_BIOS_USING_OS_MEMORY.

  ACPI has been a fatal error during the processing of a region of memory operation. The region of operation memory tried memory card which has been attributed to the use of the OS.

  This bug check usually appears in these 2 scenarios:

  1 BIOS bug / damaged and must be resolved with an update or go back to the manufacturer.

  2 Rootkit (not very common).

  Given that you have exactly the same problem and the same HP model, etc... It is a big problem on the part of HP. Contact them and let them know that you want to replace as soon as POSSIBLE, preferably if possible a working model.

  Kind regards

  Patrick

• New on Mac w/purchase of Pro. You want to run Windows applications. 8 vs 10?

  New on Mac w/purchase of Pro. You want to run Windows applications. 8 against 10 using virtualization?

  The two big names of virtualization are Parallels and VMware. They have a sort of leap-frogging each other in terms of features. Parallels has a fairly seamless integration between Mac and Windows.

  Your Mac is also already comes with Boot Camp, which lets you install Windows on a separate partition.

  ws-on-your-mac-boot-camp-vmware-parallel http://www.Macworld.co.UK/feature/Mac-software/best-virtualisation-app-run-Windo...

• My computer with Windows 7 Home updated for Firefox v34.0.5 but my two computers that are running Windows 7 Pro have not yet updated beyond Firefox v34.0. Something wrong?

  See info above. I re - run the update process at least 10 times on the two machines running Windows 7 Pro (most recently this morning), and whenever the two machines running Windows 7 Pro (one is 64-bit, one is 32-bit) say that Firefox v34.0 is "up-to-date". I checked Mozilla.org, which States that Firefox v34.0.5 was released in mid-December, but he said nothing about whether this update was only for some OSs. I also ran several scans antivirus from different vendors on two machines running Windows 7 Pro and all scans show no problems.

  Please advise is there are different versions of Firefox for Windows 7 family or Professional Edition, or if I'm having a problem. If I'm having a problem, please tell us how I can correct.

  We changed how updates were deployed to a test, that's why you were probably the 34.0.5 on a computer and 34.0.0 on the other. The only difference between them is that 34.0.5 defines yahoo as the default search. You don't need to worry because of the different versions (who both were released at the same time BTW)

• Urgent need help: I run windows 10 on iMac. I can't boot into Windows 10 after update to El Capitan 10.11.5. Help, please!

  An urgent need to help!

  I've been running Windows 10 on my iMac via Boot Camp. I just upgraded to El Capitan 10.11 to 10.11.5. I don't know if it was because of this upgrade that made me not be able to return to Windows. In the windows startup disk, my windows HD and OS X HD icons are all grayed out. So, I can't select which one to be my default startup Mode of the disc. Help, please!

  Pisheng D.

  Unlock you the boot floppies pane by clicking the lock button? Look at the lower left corner of this screen.